In this thesis, the mechanism of landslides in loess slope is studied based on a field test in association with laboratory tests and numerical modeling. The field test was carried out in the Heifangtai Plateau in China. Heifangtai belongs to semiarid monsoonal with scarce precipitation. Therefore, agricultural irrigation is the major source of water infiltration for the loess slopes in Heifangtai. The test site was selected at the crest of a steep loess slope with developed cracks, covered by more than 40m loess layer. Ground investigation, including lithological composition, groundwater level, soil sampling and soil permeability, was conducted. A field monitoring program was then performed by installation of inclinometers, piezometers, moisture probes, tensiometers and crackmeters. The field irrigation test with instrument monitoring was conducted at the test site on October 2009, lasting for 12 days. Based on field observation and monitoring results, some typical failures occurred in the field test were analyzed in details, including development of cracks, formation of sinkholes and failures on slope surface. These failures are representative in loess regions and are potential factors of loess landslides. A conceptual model was proposed to reflect soil failures induced by water infiltration along the crack. To characterize the loess behavior to infiltration, a comprehensive triaxial testing program was conducted on trimmed loess specimens sampled in Heifangtai. The fundamental behavior of loess was investigated following different stress paths under both saturated and unsaturated conditions. Based on triaxial tests, the soil parameters including mechanical properties and hydraulic properties were obtained. The finite difference program FLAC3D was adopted in this study, the fluid model of which was extended from saturated flow to saturated/unsaturated flow. A numerical model was built to study the mechanism of soil failures induced by variation of water level in the crack, using a proposed moving boundary algorithm. In the numerical modeling, fluid-mechanical coupled analysis was conducted by solving Biot’s consolidation equation, utilizing soil parameters obtained in the laboratory tests. The proposed conceptual model in the field test was verified in the numerical analysis. Subsequently, different draining rates of water in the crack were simulated to investigate soil failures affected by the dropping of water level in the crack. Based on the numerical analysis, the mechanism of sinkhole formation was discussed. Finally, conclusions and recommendations for future research on loess landslides induced by infiltration were made. It is hoped that the study on the mechanism of loess landslides can provide a useful reference for the future research. / published_or_final_version / Civil Engineering / Doctoral / Doctor of Philosophy

No description available.

Diss. (sammanfattning). Umeå : Sveriges lantbruksuniv., 2003. / Härtill 5 uppsatser.

Understanding the sources of the dust that forms the extensive loess deposits on the Chinese Loess Plateau is crucial for reconstructing atmospheric circulation patterns and dust pathways. Dust sources are however highly debated, mainly due to the low resolution of many records and the often ambiguous nature of geochemical proxies. The widely used concept of elemental ratios as provenance indicators is based on the idea that the relative abundance of immobile elements remains unaffected by chemical weathering, thereby preserving source signals. High-resolution spatial and temporal records of loess composition were determined for two study sites and three lithostratigraphic units using bulk X-ray fluorescence (XRF) analysis, and independently dated using Optically Stimulated (OSL) and post-IR Infrared Stimulated (pIR-IRSL) Luminescence dating. Four elemental ratios were chosen based on element properties of mobility and grain size, linear correlation strength and the existence of lithostratigraphic trends: Ti/Al, Si/Al, K/Al and Fe/Ti. Potential source signals were detected at both sites, at glacial-interglacial transitions as well as within lithostratigraphic units. Source changes detected within lithostratigraphic units show millennial-scale variability, indicating that abrupt shifts in dust provenance are possible. This implies that millennial-scale variability of the East Asian Monsoon may be related to changes in atmospheric dust content.

Pleistocene loess-palaeosol sequences provide a unique proxy-record enabling detailed reconstruction of Quaternary palaeoenvironments. Environmental magnetic methods are often used to read the natural archives. The loess-palaeosol sequences exposed in two sections located in southern Moravia and a sequence from central Bohemia were studied in a frame of this Diploma Thesis. Variations of bulk magnetic susceptibility, measured in the sediments, show similar pattern as in the Chinese loess-palaeosol bodies - i.e. palaeosols reveal higher magnetic susceptibility in comparison with loess due to magnetic enhancement. The magnetic enhancement is driven by weathering during pedogenic processes related to the formation of ultra-fine magnetite particles. The magnetite content is controlling the sediment magnetic behavior. The magnetic enhancement rate indicates more intense pedogenic processes in the Moravia in comparison with Bohemia. Magnetic fabric in studied loess, represented by space orientation of anisotropy of magnetic susceptibility ellipsoid, indicates dominating glacial wind palaeocurrents across the southern Moravia blowing from W or SW, respectively. The magnetic fabric in the central Bohemian sequence has revealed a dominant control of running water and re-deposition of the loess material...

Climate change is today one of our highest priority challenges. But to understand the change in climate and to be able to make predictions about the future, knowledge about past climate is of substantial importance. The key archive of past climate change can be studied through loess deposits. This paper examines loess sources in Europe and how deposits can tell us about different origins through different geochemical techniques and methods.    Secondary data of loess deposits and sources over Central-Eastern Europe have been collected and examined in order to test some of the possible major dust source areas for European loess deposits that have been suggested by other scientists.   Different techniques and methods are used to examine loess sediments when trying to identify their origin. Generally, techniques and methods can be divided into geochemical and analytical parameters, which are XRD (X-ray diffraction) and XRF (X-ray fluorescence spectrometry), elemental ratios, SrNd isotopic analyses, zircon U-Pb geochronology, combined bulk and single grain analyses, as well as more statistical approaches.    The results are based on the three mainly studied articles show that it is more likely that loess sources are coming from High Alps and mountain areas, such as the Carpathians, rather than from glaciers, as was previously the main idea.   This paper therefore draws the conclusion that loess material, in most cases, seems to be originating from relatively nearby and local mountain areas and only a small portion appear to have been transported longer distances.

Analyzing climate changes by loess sediment deposits formed after the last glacial maximum gives us information about how the environment was dynamically before humans physically could record climate changes. Sampling and analyzing loess from different places in the world give us a more reliable view of when events and changes in climate took place. Loess is a last step eolian transported, fine grained sediment and can be a good record as a Quaternary climate archive (Muhs 2013; Stevens et al. 2020). Loess-paleosol sequences can be used as a relative record for climate change. The paleosols in the sequence corresponds to soil which can indicate warmer interglacial/interstadial periods when chemical weathering was active at site. Loess in these sequences reflects on cold and dry climate during glacial periods (Buggle et al. 2008; Muhs 2013). By analyzing geochemical composition of bulk-samples from chosen site one can get information about if paleosols or loess deposits are present at certain depths of profile. Also, if a glacial or interglacial period was present then (Buggle et al. 2011; Johansson 2017). In this study X-ray fluorescence Spectroscopy (XRF), will be used to analyze elemental composition of loess. This to see how soluble and mobile elements relate to immobile and non-soluble ones. This can indirectly tell how paleosols and loess are distributed over the site and if shifts attempt by depth. The samples of loess in this study were taken from north-western France at a site called Primel-Tregastel. Soil weathering indexes will be used in this study to calculate weathering intensities for deposit. Na/Al-based indices called CIA, CIW, CPA, PIA, Index B and Sr-based ratios Ba/Sr and Rb/Sr was used (Buggle et al. 2011). The purpose of the study is to see if weathering has been active at site. And if, to reconstruct at which depths and to make a paleoclimatic interpretation of the site. Na/Al-based indices CIA, CIW, CPA, PIA and Index B shows indications of active weathering at site. Sr-based ratios Ba/Sr and Rb/Sr do also show same indications but with more dramatically variations. The content of mobile and immobile elements does also follow the principle that when mobile elements decrease in percentage, immobile elements get enriched in bulk-sample. The trends shown are a long time of cold climate due to low weathering intensities followed by one warmer and more humid period. Increasing weathering intensities, indicating an interglacial/interstadial period happens as a first development. Continuously a decrease happens in weathering intensity which would indicate a start of a colder period. Topmost layer has been improved and re-worked by human activity and will be misleading to use in a geochemical analysis and paleoenvironmental interpretation. / Att analysera klimatförändringar genom lössjordar formade efter senaste glaciala maximumet ger oss information om hur miljön såg ut dynamiskt innan människan hade möjligheten att mäta klimatvariationer. Genom analys och provtagning av lössjordar från olika platser i världen ger oss en mer trovärdig bild över när händelser och förändringar i klimat skedde. Lössjord är ett slutligen vindtransporterad, finkornigt sediment som även fungerar bra som register för Kvartära klimatarkiv (Muhs 2013; Stevens et al. 2020). Loess-paleosol sekvenser kan användas som ett relativt register för klimatförändringar. Paleosolerna i sekvensen motsvarar jord som indikerar varmare interglaciala/interstadiala perioder när kemisk vittring kan ha varit aktiv. Lössavlagringar i sekvensen reflekterar kallare och torrare klimat under glaciala istider (Buggle et al. 2008; Muhs 2013). Genom att analysera geokemiskt innehåll av prover från lokal kan man få fram information om paleosoler eller lössavlagringar finns vid visst djup i profilen. Indirekt även om en glacial eller interglacial period pågick då (Buggle et al. 2011; Johansson 2017). I den här studien används X-ray fluorescens Spektroskopi (XRF) för att analysera geokemiskt innehåll av lössjord. Detta för att se hur lösliga och mobila element är relaterade till icke-mobila och icke-lösliga element. Det kan indirekt peka på hur paleosoler och löss är fördelat över en lokal och visa om skillnader finns vid olika djup. Proverna i denna studie är tagna från nord-västra Frankrike vid en lokal som heter Primel Trégastel. Jord vittrings index kommer att användas i studien för att beräkna vittringsintensiteter för avlagringen. Na/Al-baserade index som heter CIA, CIW, CPA, PIA och Index B och Sr-baserade förhållanden Ba/Sr och Rb/Sr kommer användas (Buggle et al. 2011). Syftet med studien är att se om vittring har skett vid lokalen. Och om vittring påvisas, kunna rekonstruera vid vilka djup och slutligen göra en paleoklimatisk tolkning över lokal. Na/Al-baserade index CIA, CIW, CPA, PIA och Index B visar indikationer av vittring som varit aktiv vid studerad lokal. Sr-baserade förhållanden Ba/Sr och Rb/Sr visar samma indikation men med mer dramatiska variationer. Innehållet av mobila och icke-mobila element följer även principen om att när mobila element minskar i procent så ökar dom icke-mobila elementen. Trenderna som visas är en lång tid av kallt klimat med låg vittringsintensitet som följs av en varmare och fuktigare period med högre vittringsintensitet. Utvecklingen av denna ökande vittringsintensitet indikerar en pågående interglacial/interstadial period. Fortsättningsvis sker en minskning i vittringsintensitet vilket påvisar en början av en kallare period. Det översta lagret i lokalen har bevisats blivit förändrat av mänsklig aktivitet och kan var missvisande i en geokemisk analys och paleoklimatologisk tolkning.

The aeolian sediment loess, which consists of mineral dust, is one of the most detailed terrestrial record of both global and regional climate changes. As climate changes in the past cover a much wider range of climate variability than humans have directly recorded, the soil memory of loess is vital for understanding the Earth’s climate system. By examining past climate records and analyzing past climate changes and factors that have instigated changes, inferences regarding future climate can be made. Therefore, the aim of this research was to define the specific depositional and post-depositional conditions of a loess sequence in Primel-Tr gastel, Brittany, north-western France. This was done by examining the magnetic susceptibility (MS), and loss on ignition (LOI) of 63 samples from the Primel-Tr gastel sequence. The result suggests that the lower part was formed during a relatively long, cold and dry period, with significant temperature oscillations, resulting in several periglacial phases. The data also shows an increase in the MS signal for the middle units, which then gradually decreases simultaneously as there is a sharp rise in the proportion of organic matter (OM). This is followed by a steep drop and finally an overall increase in OM, which suggests that this period has been characterized by both stadial and interstadial phases. The upper part displays a general increase in MS values, as well as increased organic matter, which implies a milder climate with increased temperatures. The study provides the first comprehensive estimate of the regional climate variability and provides a base towards a more comprehensive and overarching understanding of our climate system.

Loess-paleosol sequences preserve information that can be used to reconstruct paleoenvironement, specifically the climatic conditions and the vegetation present at the time of their formation. A dense network of reliably analyzed sequences from different geographic locations is crucial for representation of ecological and climatic trends during the Pleistocene (Frechen, 2011). The aim of this thesis is to fill the gap in the geographical distribution of well described loess-paleosol sequences in Central Europe. Therefore, it focuses on a loess- paleosol sequence in Bůhzdař, situated 9 km NW of Prague, Czech Republic. This profile was last studied in 1952 by naturalist Vojen Ložek. This thesis uses a number of analyses in order to get a multi-proxy record of local paleoenvironmental changes archived in a sequence of alternating loess sediments and paleosols in Bůhzdař. Geochemical approaches are combined with grain size distribution to define climatic conditions at the time of formation of the strata. Key words: loess/paleosol sequences, Bůhzdař, Czech Republic, particle size distribution, total organic carbon, XRF, XRD, stable isotopes 13 C and 18 O

More than two million people in the Chaco-Pampean plain in central Argentina are affected by high As levels in groundwater. The concentrations of As are far exceeding the WHO standard limit for safe drinking water of 0.1 μg/L and the provisional Argentinean limit of 0.5 μg/L. The NE of La Pampa province is one of the areas affected with geogenic As in shallow aquifers within the Chaco-Pampean plain. These aquifers are in closed basins and they are only available water resource of the region for drinking and agriculture purposes. The Pampean aquifer is composed of a multi-layered system of Quaternary loess deposits covered by aeolian sands and also containing layers of rhyolitic volcanic ash, which is considered the primary source of As. Volcanic ash layers can be visible in the shallow sediments or intermixed in the loess. During the weathering of volcanic ash sediments As is dissolved to the aqueous phase and can be quickly adsorbed or co-precipitated on secondary Fe, Al and Mn oxy-hydroxides under favourable conditions. Also, previous more arid climatic conditions have led to the formation of carbonate "calcrete" layers in the top sequences of the loess and this has affected the geochemistry of the aquifer. Two sites were investigated in the NE of La Pampa province in order to assess (i) the quality of groundwater for drinking water use, (ii) the distribution of As and other trace elements in shallow aquifers and (iii) to understand better the factors controlling its mobility in groundwater. The results showed that groundwater was circum-neutral to alkaline and under moderate oxidizing conditions. The predominant groundwater composition was of Na-HCO3 for fresh water and Na-Cl-SO42- for brackish water types. High salinity levels are evidenced by the high Electrical Conductivity and might be explained by to the high evaporation rates. Groundwater sampled in both areas was enriched with As, F and other trace elements at different ranges of concentration. From the total As concentrations, arsenate As(V) predominated over arsenite As(III) species. Shallow groundwater is also enriched with fluoride exceeding the WHO standard limit of 1.5 mg/L and placed in the same As hotspots. One possible factor controlling the mobility of As is the high pH of groundwater, which is controlled by the carbonates equilibrium. Under this high pH conditions As is less strongly bind to Fe, Al and Mn oxy-hydroxides and can be easily mobilized to groundwater when other competing ions are getting adsorbed on the surface sites of binding minerals.