In terms of acreage, forage is the number one crop in Virginia. The backbone of these forages has long been tall fescue (Lolium arundinaceum (Schreb.) S.J. Darbyshire). Knowledge of the plant species that make up a pasture and the relative amounts of each species present is important for interpreting potential animal performance. It is also important to know the relative amounts and types of weeds present and to monitor for the presence of poisonous plants or noxious weeds. An experiment was conducted in 2003 through 2005 to investigate botanical composition and yield of "Lakota" prairie grass (Bromus catharticus Vahl.), "Kentucky 31" endophyte-infected (KY31 E+), endophyte-free (KY31 E-), and "Quantum" tall fescue (non toxic endophyte infected) under grazing by stocker steers. Forage botanical composition and yield were determined by clipping three 0.25-m2 areas per treatment replicate. Prior to harvesting, the canopy height within each quadrate was measured with a disc meter. In 2005, productive ground cover was assessed using visual evaluation techniques, point quadrat method, and digital imagery quantified with terrestrial remote sensing. Forages were established September 2002 and grazing was initiated in July of 2003. Experimental design was a randomized complete block with four replications. Averaged over the three years the yield of KY31E+ was higher (p<0.05) than all other treatments. Lakota prairie grass had lower (p<0.05) yields than both KY31 E+ and Quantum tall fescue, however no yields did not differ between Lakota prairie grass and KY31 E-. Our results showed a typical forage distribution curve for all the treatments. Early spring, summer, and fall productivity of Lakota prairie grass was less than all the fescues, thus did not extend the grazing season. Forage persistence was greatest for KY31 E+ and Quantum and lowest for Lakota when averaged over all years. Among sampling methods for ground cover, terrestrial remote sensing was the most accurate, compared with visual evaluation and point quadrat methods. For estimates of all yield indirect methods of assessment had high errors; however the plate meter calibrated by sward density seemed the least variable of the methods tested. / Master of Science

In recent years, there is a clear trend toward increasing the demand for electric power in high-power applications. High-power converters are making major impacts on these high-power applications. Recent breakthroughs in Silicon Carbide (SiC) materials and fabrication techniques have led to the development of high-voltage, high-frequency power devices, which are at the heart of high-power converters. SiC metal-oxide semiconductor field-effect transistors (MOSFETs) have advantages over silicon (Si) devices due to their higher breakdown voltage, higher thermal capability, and lower on-state resistance. However, their fast switching frequency and high blocking voltage bring challenges to the gate-drive circuit design. The gate driver of SiC-MOSFETs requires a power supply that provides a high-voltage, high-density design, a low input-output capacitance (CI/O) transformer design, good voltage regulation, as well as good resilience to faults to enable safe and fast operation. In this thesis, a power supply that supplies multiple gate drivers for 10 kV SiC MOSFETs is presented. A transformer design approach with a single turn at the primary side is proposed. A 20 kV insulation is achieved by the primary HV cable insulation across a toroid transformer core. The CI/O is designed less than 2 pF to mitigate the Common-Mode (CM) noise. A circuit topology analysis is performed and the inductor/capacitor/capacitor/inductor (LCCL) – inductor/capacitor (LC) circuit is selected. This circuit allows Zero-Voltage Switching (ZVS) at full operation range. A Resonant-Current-Bus (RCB) is built at the transformer primary side to achieve load-independence. / Master of Science / Wide-bandgap semiconductor devices have attracted widespread attention due to their superior performance compared to their silicon devices counterpart. To utilize its full benefits, this thesis presents a complete design and optimization of a gate-drive power supply that supplies multiple gate drivers for high-voltage, high-speed semiconductor devices. Four objectives, including high density at high voltage, good noise mitigation, fair voltage regulation, resilience to faults have been achieved. During the design procedure, different topology candidates are introduced and compared, after which a resonant topology is selected. The wide-bandgap semiconductor devices are utilized to reduce the size and losses. Hardware assembly is shown and experimental testing results are provided in the end to verify the design.

Portland cement concrete (PCC) structures deteriorate with age and need to be maintained or replaced. Early detection of deterioration in PCC (e.g., alkali-silica reaction, freeze/thaw damage, or chloride presence) can lead to significant reductions in maintenance costs. However, it is often too late to perform low-cost preventative maintenance by the time deterioration becomes evident. Non-destructive evaluation (NDE) methods are potentially among the most useful techniques developed for assessing constructed facilities. They are noninvasive and can be performed rapidly. Portland cement concrete can be nondestructively evaluated by electrically characterizing its complex dielectric constant. The real part of the dielectric constant depicts the velocity of electromagnetic waves in PCC. The imaginary part describes the conductivity of PCC and the attenuation of electromagnetic waves, and hence the losses within the PCC media. Dielectric properties of PCC have been investigated in a laboratory setting using a parallel plate capacitor operating in the frequency range of 0.1MHz to about 40MHz. This capacitor set-up consists of two horizontal-parallel plates with an adjustable separation for insertion of a dielectric specimen (PCC). While useful in research, this approach is not practical for field implementation In this research, a capacitance probe has been developed for field application. The probe consists of two planar conducting plates and is made of flexible materials for placement on exposed surfaces of the specimens to be tested. The calibration method of both capacitive systems has been extensively studied to minimize systematic errors in the measurement process. These two measurement systems will be discussed and compared to one another on the basis of sensitivity and measurement repeatability. / Master of Science

As device technologies migrate into Deep Submicron (DSM) feature sizes, high-performance power-efficient computer architectures that keep pace with improving technologies need to be explored. Technology scaling increases the effects of wire latencies, inductive effects, noise and crosstalk in on-chip communication, limiting the performance of DSM designs. Power efficient performance gains from Instruction Level Parallelism (ILP) are reaching a limit. Single-Chip Parallel Computers are promising solutions to the DSM design challenges and the performance limitations of ILP. These systems are explicitly modular architectures that efficiently support Thread Level Parallelism (TLP) while avoiding global signals and shared resources. Microarchitectural level power analysis is required for evaluating the feasibility of newly conceived architectures in terms of power dissipation and energy efficiency. Accounting for power in the early stages of design shortens the time-to-market due to reduced design iteration times. Power optimizations at the architectural level can yield large power savings. This thesis proposes a microarchitectural level power estimation and analysis infrastructure for Single Chip Parallel Computers. The power estimation tool and the analysis methodology are developed based on the Single Chip Message-Passing Parallel (SCMP) Computer and can be extended to other Single Chip Parallel Computers. The thesis focuses on the development of power estimation models, construction of the power analysis tool, study of the power advantages of the architecture and identification of subsystems requiring power optimization. / Master of Science

Dielectric elastomers (DEs) are a relatively new electroactive polymer (EAP) transducer technology. They are capable of over 100% strain when actuated, and can be used as sensors to measure large strains. In actuation mode, the DE is subject to an electric field; in sensing mode, the capacitance of the dielectric elastomer is measured. In this work, a dielectric elastomer configured as a circular membrane clamped around its outer edge over a sealed chamber and inflated by a bias pressure is studied in order to characterize its static and dynamic electromechanical behavior. In both cases, the experiments were conducted with prestretched dielectric elastomer actuators fabricated from 0.5 mm or 1 mm thick polyacrylate films and unless stated otherwise carbon grease electrodes were used. The static tests investigate the effect of flexible electrodes and passive layers on the electromechanical response of dielectric elastomer membrane actuators and sensors. To study the effect of the flexible electrodes, four compliant electrodes were tested: carbon grease, silver grease, graphite spray, and graphite powder. The electrode experiments show that carbon grease is the most effective electrode of those tested. To protect the flexible electrodes from environmental hazards, the effect of adding passive elastic layers to the transducers was investigated. A series of tests were conducted whereby the position of the added layers relative to the transducer was varied: (i) top passive layer, (ii) bottom passive layer, and (iii) passive layers on both the bottom and top of the transducer. For the passive layer tests, the results show that adding elastic layers made of the same material as the DE dramatically changes both the mechanical and electrical response of the actuator. The ability to use capacitance measurements to determine the membrane's maximum stretch was also investigated. The experiments demonstrate that the capacitance response can be used to sense large mechanical strains in the membrane ï ³ 25%. In addition, a numerical model was developed which correlates very well with the experimental results especially for strains up to 41%. The dynamic experiments investigate the dynamic response of a dielectric elastomer membrane due to (i) a time-varying pressure input and (ii) a time-varying voltage input. For the time-varying pressure experiments, the prestretched membrane was inflated and deflated mechanically while a constant voltage was applied. The membrane was cycled between various predetermined inflation states, the largest of which was nearly hemispherical, which with an applied constant voltage of 3 kV corresponded to a maximum strain at the pole (center of membrane) of 28%. These experiments show that for higher voltages, the volume displaced by the membrane increases and the pressure inside the chamber decreases. For the time varying voltage experiments, the membrane was passively inflated to various predetermined states, and then actuated. Various experiments were conducted to see how varying certain system parameters changed the membrane's dynamic response. These included changing the chamber volume and voltage signal offset, as well as measuring the displacement of multiple points along the membrane's radius in order to capture its entire motion. The chamber volume experiments reveal that increasing the size of the chamber onto which the membrane is clamped will cause the resonance peaks to shift and change in number. For these experiments, the pole strains incurred during the inflation were as high as 26 %, corresponding to slightly less than a hemispherical state. Upon actuation using a voltage signal with an amplitude of 1.5 kV, the membrane would inflate further, causing a maximum additional strain of 12.1%. The voltage signal offset experiments show that adding offset to the input signal causes the membrane to oscillate at two distinct frequencies rather than one. Lastly, experiments to capture the entire motion of the membrane revealed the different mode shapes the membrane's motion resembles. / Master of Science

With recent advancements in material science, industrial operations are being conducted at higher and higher temperatures. This is apparent in the nuclear industry where a division of the field is working to develop the High Temperature Gas Reactor and the Very High Temperature Gas Reactor concurrently. Both of these facilities will have outlet gas temperatures that are at significantly higher temperatures than the typical water cooled reactor. These increased temperatures provide improved efficiency for the production of hydrogen, provide direct heating for oil refineries, or more efficient electricity generation. As high temperature operations are being developed, instruments capable of measuring the operating parameters must be developed concurrently. Within the gas reactor community there is a need to measure the impurities within the primary coolant. Current devices will not survive the temperature and radiation environments of a nuclear reactor. An instrument is needed to measure the impurities within the coolant while living inside the reactor, where this instrument would measure the amount of the impurity within the coolant. There are many industrial applications that need to measure the ratio of two components, whether it be the amount of particulate in air that is typical to pneumatic pumping, or the liquid to gas ratio in natural gas as it flows through a pipeline. All of the measurements in these applications can be met using a capacitance sensor. Current capacitance sensors are built to operate at ambient temperatures with only one company producing a product that will handle a temperature of up to 400 °C. This maximum operating temperature is much too low to measure the gas characteristics in the High Temperature Gas Reactor. If this measurement technique were to be improved to operate at the expected temperatures, the coolant within the primary loop could be monitored for water leaks in the steam generator, carbon dust buildup entrained in the flow, or used to measure the purity of the coolant itself. This work details the efforts conducted to develop such an instrument. While the concept of designing a capacitance sensor to measure a gas mixture is not unique, the application of using a capacitance sensor within a nuclear reactor is a new application. This application requires the development of an instrument that will survive a high temperature nuclear reactor environment and operate at a sensitivity not found in current applications. To prove this technique, instrument prototypes were built and tested in confined environments and at high temperatures. This work discusses the proof of concept testing and outlines an application in the High Temperature Test Facility to increase the operational understanding of the instrument. This work is the first step toward the ultimate outcome of this work, which is to provide a new tool to the gas reactor community allowing real-time measurements of coolant properties within the core. / Graduation date: 2013

Philosophiae Doctor - PhD (Chemistry) / Supercapacitors, also known as ultracapacitors or electrochemical capacitors, are considered one of the most important subjects concerning electricity or energy storage which has proven to be problematic for South Africa. In this work, graphene oxide (GO) was supported with platinum, silver and copper nanoparticles anchored with dodecylbenzenesulphonic acid (DBSA) doped polyaniline (PANI) to form nanocomposites. Their properties were investigated with different characterization techniques. The high resolution transmission electron microscopy (HRTEM) revealed GO's nanosheets to be light, flat, transparent and appeared to be larger than 1.5 ?m in thickness. This was also confirmed by high resolution scanning electron microscopy (HRSEM) with smooth surfaces and wrinkled edges observed with the energy dispersive X-ray analysis (EDX) confirming the presence of the functional groups such as carbon and oxygen. The HRTEM analysis of decorated GO with platinum, silver and copper nanoparticles (NPs) revealed small and uniformly dispersed NPs on the surface of GO with mean particle sizes of 2.3 ± 0.2 nm, 2.6 ± 0.3 nm and 3.5 ± 0.5 nm respectively and the surface of GO showed increasing roughness as observed in HRSEM micrographs. The X-ray fluorescence microscopy (XRF) and EDX confirmed the presence of the nanoparticles on the surface of GO as platinum, silver and copper which appeared in abundance in each spectra. Anchoring the GO with DBSA doped PANI revealed that single GO sheets were embedded into the polymer latex, which caused the DBSA-PANI particles to become adsorbed on their surfaces. This process then appeared as dark regions in the HRTEM images. Morphological studies by HRSEM also supported that single GO sheets were embedded into the polymer latex as composite formation appeared aggregated and as bounded particles with smooth and toothed edges.

The content of this thesis is the validation of the method of dynamic testing of solar photovoltaic cells. Testing methods for determining the parameters of the photovoltaic cell replacement scheme has been verified through testing a set of crystalline silicon photovoltaic cells. To accelerate the diffusion capacity measurement and to improve reproducibility of the measurement we propose new method of determining the time constant for diffusion capacitance using a combination of two short pulses. For this method of measurement new scheme for dynamic tester timing has been proposed and implemented.

Philosophiae Doctor - PhD / Energy storage technologies are rapidly being developed due to the increased awareness of global warming and growing reliance of society on renewable energy sources. Among various electrochemical energy storage technologies, high power supercapacitors and lithium ion batteries with excellent energy density stand out in terms of their flexibility and scalability. However, supercapacitors are handicapped by low energy density and batteries lag behind in power. Supercapatteries have emerged as hybrid devices which synergize the merits of supercapacitors and batteries with the likelihood of becoming the ultimate power sources for multi-function electronic equipment and electric/hybrid vehicles in the future. But the need for new and advanced electrodes is key to enhancing the performance of supercapatteries. Leading-edge technologies in material design such as nanoarchitectonics become very relevant in this regard. This work involves the preparation of vanadium pentoxide (V2O5), pristine and zinc doped lithium manganese silicate (Li2MnSiO4) nanoarchitectures as well as their composites with hydroxylated graphene (G-ol) and carbon nanotubes (CNT). / 2023-12-01

Thesis (MScEng (Electrical and Electronic Engineering))--University of Stellenbosch, 2006. / In order to rapidly detect, monitor and predict changes in milk as it ferments, sensors would need to be designed specifically for milk. To this end, invasive surgical stainless steel probes were investigated and the probe impedances were characterised according to measurements made in various saline concentrations. Based on these findings, specific probes were designed that were robust and easy to use in milk. To measure multiple probe sensors continuously and accurately, an automatic measurement device was designed and manufactured. The device was self-sustaining, portable and calculated and stored all probe impedance data internally, allowing experimental runs to take place in controlled laboratory environments. The probes designed in this thesis were consequently tested in various milk fermentation experiments and it was found that surgical stainless steel probes were effective at detecting and monitoring fermentation changes. The probe impedance changes also lead the pH changes in milk, giving it a predictive element. The probe sensor studies provided enough data so that studies could be done into potential non-invasive sensors. Therefore, capacitive sensors were investigated and a fringe field capacitor was presented as a potential non-invasive milk fermentation sensor.