"Adhesion Molecules have been associated with a number of neurological and psychological disorders (humans), and implicated in various developmental processes (animals). Better understanding the development of the nervous system and the roles of adhesion molecules in it may be crucial to better understanding these disorders. LIGs, Leucine Rich Repeat and ImmunoGlobulin containing transmembrane proteins, represent a novel class of such adhesion molecules and have been implicated in various neuronal processes, including neurite outgrowth, axonal pathfinding, neuronal regeneration and survival. Two such LIGs are Kek1 and Kek2, members of a Drosophila LIG family, which have been reported to function in axonal pathfinding and synaptic plasticity, respectively. It is unclear what their roles in these processes are, as well as if other members of the Drosophila LIG family have similar roles. Current studies aim to survey the Kekkon family function in the nervous system, looking to identify new phenotypes and/or to elucidate the mechanisms underlying previously identified phenotypes. To achieve this goal, tissue specific inducible RNAi technique was employed. Validating of a number of transgenic RNAi stocks obtained was necessary and showed that all stocks obtained promoted specific and efficient knock down of target gene. Next an assessment of RNAi knockdown efficacy in developing nervous system was carried out and knockdown was shown to be weak if not in the presence of Dicer-2 co-misexpression. A number of screens for general behavioral phenotypes were performed including ubiquitous, neural, and imaginal discs knockdown. These uncovered possible effects of kek1 neural knockdown, as well as possible interaction of Kek1 with neurotactin, neuroglian and kek2. NMJ analysis of Kek5 and Kek6 was also carried out and preliminary results indicate possible interaction of kek5 in NMJ, although no statistical significance was detected."

Diferentes mecanismos têm sido mostrados por estar envolvidos na evasão à morte mediada por complemento. Neste estudo, demonstramos que a aquisição do FH pela Leptospira é crucial para a sobrevivência das bactérias no soro e que estas espiroquetas interagem com FH, FHL-1, FHR-1 e C4BP. Nós também demonstramos que a ligação à estes reguladores é mediada pelas proteínas leptospiral immunoglobulin-like (Lig). FH se liga as proteínas Lig via short consensus repeat (SCR) principalmente pelos domínios 5 e 20. Ensaios de competição sugerem que FH e C4BP têm sítios de ligação diferentes nas proteínas Lig. Além disso, FH e C4BP ligados nas proteínas Lig mantêm a atividade de cofator, mediando a degradação de C3b e C4b pelo FI. Nós demonstramos que a aquisição de FH e C4BP pela L. biflexa transgênica para LigA e LigB exercem um papel de proteção na sobrevida destas bactérias. Análise por citometria de fluxo também confirmaram a capacidade das leptospiras transgênicas para controlar a deposição de C3, C4 e MAC. As proteínas Lig também foram capazes de ligar plasminogênio, o qual foi ativado em plasmina e esta enzima foi capaz de degradar fibrinogénio, C3b e C5. Estas clivagens inativam C3b e C5, evitando a progressão da cascata, e bloqueando as três vias de complemento. / Different mechanisms have been shown to be involved in evasion of complement-mediated killing. In this study, we demonstrate that acquisition of FH on the Leptospira surface is crucial for bacterial survival in the serum and that these spirochetes interact with FH, FHL-1, FHR-1 and C4BP. We also demonstrate that binding to these regulators is mediated by leptospiral immunoglobulin-like (Lig) proteins. FH binds to Lig proteins via short consensus repeat (SCR) domains 5 and 20. Competition assays suggest that FH and C4BP have distinct binding sites on Lig proteins. Moreover, FH and C4BP bound to immobilized Ligs display cofactor activity, mediating C3b and C4b degradation by FI. We demonstrated that acquisition of FH and C4BP by the LigA and LigB transformed L. biflexa have the protective role, being crucial by bacterial survival. Analysis by Cytometer fluid also confirmed the ability of L. biflexa expressing LigA and LiB to controller the deposition of C3, C4 and MAC. Lig proteins were able to bind plasminogen, which was activated to plasmin and this enzyme was able to degrade the fibrinogen, C3b and C5. These cleavages inactivate C3b and C5, preventing progression of the complement cascade and blocking the three complement pathways.

Diferentes mecanismos têm sido mostrados por estar envolvidos na evasão à morte mediada por complemento. Neste estudo, demonstramos que a aquisição do FH pela Leptospira é crucial para a sobrevivência das bactérias no soro e que estas espiroquetas interagem com FH, FHL-1, FHR-1 e C4BP. Nós também demonstramos que a ligação à estes reguladores é mediada pelas proteínas leptospiral immunoglobulin-like (Lig). FH se liga as proteínas Lig via short consensus repeat (SCR) principalmente pelos domínios 5 e 20. Ensaios de competição sugerem que FH e C4BP têm sítios de ligação diferentes nas proteínas Lig. Além disso, FH e C4BP ligados nas proteínas Lig mantêm a atividade de cofator, mediando a degradação de C3b e C4b pelo FI. Nós demonstramos que a aquisição de FH e C4BP pela L. biflexa transgênica para LigA e LigB exercem um papel de proteção na sobrevida destas bactérias. Análise por citometria de fluxo também confirmaram a capacidade das leptospiras transgênicas para controlar a deposição de C3, C4 e MAC. As proteínas Lig também foram capazes de ligar plasminogênio, o qual foi ativado em plasmina e esta enzima foi capaz de degradar fibrinogénio, C3b e C5. Estas clivagens inativam C3b e C5, evitando a progressão da cascata, e bloqueando as três vias de complemento. / Different mechanisms have been shown to be involved in evasion of complement-mediated killing. In this study, we demonstrate that acquisition of FH on the Leptospira surface is crucial for bacterial survival in the serum and that these spirochetes interact with FH, FHL-1, FHR-1 and C4BP. We also demonstrate that binding to these regulators is mediated by leptospiral immunoglobulin-like (Lig) proteins. FH binds to Lig proteins via short consensus repeat (SCR) domains 5 and 20. Competition assays suggest that FH and C4BP have distinct binding sites on Lig proteins. Moreover, FH and C4BP bound to immobilized Ligs display cofactor activity, mediating C3b and C4b degradation by FI. We demonstrated that acquisition of FH and C4BP by the LigA and LigB transformed L. biflexa have the protective role, being crucial by bacterial survival. Analysis by Cytometer fluid also confirmed the ability of L. biflexa expressing LigA and LiB to controller the deposition of C3, C4 and MAC. Lig proteins were able to bind plasminogen, which was activated to plasmin and this enzyme was able to degrade the fibrinogen, C3b and C5. These cleavages inactivate C3b and C5, preventing progression of the complement cascade and blocking the three complement pathways.

Magazine readers in South Africa have a wide choice: there are more than 188 consumer magazines on the shelf and this gives readers the opportunity to choose what they like. However, there are very few Afrikaans Christian magazines and they have to compete commercially with the other publications. The question that arises is how these magazines manage to maintain a Christian character while at the same time staying competitive. In an attempt to answer this question, this study investigates the covers and contents of Finesse, Lig and Lééf. A literature study was used to determine which features and approaches can be used to make a Christian magazine's agenda (and therefore approach) unique. A qualitative content analysis is used to investigate how the covers and contents of Finesse, Lig and Lééf correlate with what one associates with Christian journalism, and how these magazines differ from one another in this regard. All these findings are compared with the biggest Afrikaans women's magazine, Sarie, to identify correspondences and differences. Semi-structured interviews were also held with the editors of Finesse, Lig and Lééf. Specific directive arguments were formulated about the features of Christian journalism and about agenda setting and the role of magazine covers. These specific directive arguments were used as a guideline in the content analysis. It was found that all four publications in question use well-known personalities (like actresses, singers and sports stars) as cover models. However, there are differences in the way the covers are presented and framed. Ug and Leer give noticeably more attention to the spiritual lives of their models, and as a result these magazines have clear features that can be associated with Christian journalism. Signs of the so-called "celebrity" culture were particularly evident in the covers and contents of Finesse and Sarie. In summary, it may be argued that Ug and Leer (which are outspoken Christian publications) strongly display their Christian character. On the other hand, Finesse (who views itself not as a Christian publication but as a lifestyle publication for the Christian woman) less consistently displays a Christian character. There is a strong distinction between Lig and Lééf and the secular Sarie, whereas Finesse displays more correspondences with Sarie. / Thesis (M.A. (Communication Studies))--North-West University, Potchefstroom Campus, 2010

Magazine readers in South Africa have a wide choice: there are more than 188 consumer magazines on the shelf and this gives readers the opportunity to choose what they like. However, there are very few Afrikaans Christian magazines and they have to compete commercially with the other publications. The question that arises is how these magazines manage to maintain a Christian character while at the same time staying competitive. In an attempt to answer this question, this study investigates the covers and contents of Finesse, Lig and Lééf. A literature study was used to determine which features and approaches can be used to make a Christian magazine's agenda (and therefore approach) unique. A qualitative content analysis is used to investigate how the covers and contents of Finesse, Lig and Lééf correlate with what one associates with Christian journalism, and how these magazines differ from one another in this regard. All these findings are compared with the biggest Afrikaans women's magazine, Sarie, to identify correspondences and differences. Semi-structured interviews were also held with the editors of Finesse, Lig and Lééf. Specific directive arguments were formulated about the features of Christian journalism and about agenda setting and the role of magazine covers. These specific directive arguments were used as a guideline in the content analysis. It was found that all four publications in question use well-known personalities (like actresses, singers and sports stars) as cover models. However, there are differences in the way the covers are presented and framed. Ug and Leer give noticeably more attention to the spiritual lives of their models, and as a result these magazines have clear features that can be associated with Christian journalism. Signs of the so-called "celebrity" culture were particularly evident in the covers and contents of Finesse and Sarie. In summary, it may be argued that Ug and Leer (which are outspoken Christian publications) strongly display their Christian character. On the other hand, Finesse (who views itself not as a Christian publication but as a lifestyle publication for the Christian woman) less consistently displays a Christian character. There is a strong distinction between Lig and Lééf and the secular Sarie, whereas Finesse displays more correspondences with Sarie. / Thesis (M.A. (Communication Studies))--North-West University, Potchefstroom Campus, 2010

The hybridization of direct write (DW) and additive manufacturing (AM) technologies to create additively manufactured electronics (AME) has enabled the integration of electrical functionality to form multifunctional AM components. Current work in AME has demonstrated the integration of conductive traces into and onto geometries and form factors that are not possible through traditional electronics packaging processes. This has largely been accomplished by using AM and DW technology to deposit conductive inks to form interconnects on the surface of AM substrates or within multimaterial AM geometries. However, the requisite thermal post-processing and high resistivity of the conductive inks and the limitations in thermal and dielectric performance of printable substrates commonly used in AME restrict the capabilities of these parts. This thesis proposes an alternative process for the conformal deposition of low resistivity traces on additively manufactured all-aromatic polyimides (AM-PI) without the use of conductive inks. This is accomplished through the selective patterning of laser induced graphene (LIG), a porous 3D graphene fabricated via laser irradiation, onto the AM-PI. While the resultant LIG is conductive, its resistivity is further reduced by the electrodeposition of copper (Cu-LIG). In this thesis, the synthesis of LIG on AM-PI, thermally post processed to 240℃, 300℃, and 450℃, is demonstrated and characterized through sheet resistance measurements and Raman spectroscopy. AM-PI post-processed to 300℃ demonstrated the lowest resistivity LIG formation (13.8 Ω/square). The resistivity of Cu-LIG is compared to an industry standard silver ink (Micromax CB028) used in direct write hybrid manufacturing applications. Cu-LIG was found to have a measured resistivity (1.39e-7 Ω·m), two orders of magnitude lower than the measured resistivity of the CB028 silver ink (1.62e-5 Ω·m). Additionally, the current capacity of the Cu-LIG was demonstrated and Joule heating of the material was observed via IR thermography. Cu-LIG demonstrated no failure of conductive trace or substrate under 5A of current for 2 minutes, heating to a maximum recorded temperature of 76.3℃. Several multifunctional components were fabricated as case studies to further validate the process. Several small passive electronic devices (e.g., a heater and an interdigitated capacitor) are fabricated to demonstrate selective deposition of complex copper traces. The fabrication of an Archimedes spiral on a hemispherical substrate via Cu-LIG is completed to demonstrate the ability to use the process to fabricate conformal conductive traces. An LED circuit is fabricated on a face-center cubic AM-PI lattice which demonstrates multi-planar fabrication on geometrically complex 3D printed substrates. / Master of Science / The hybridization of direct write (DW) and additive manufacturing (AM) technologies to create additively manufactured electronics (AME) has enabled the fabrication of AM components which have electronic functionality. Current work in AME has demonstrated the integration of conductive traces into and onto geometries and form factors that are not possible through traditional electronics packaging processes. This has largely been accomplished through the deposition of conductive inks to form interconnects on the surface of AM substrates or within multimaterial AM geometries. However, these conductive inks require thermal post-processing temperatures which exceed the thermal performance of common AM substrates. The dielectric performance of AM substrates is also restrictive to the capabilities of these parts. This thesis proposes an alternative process for the conformal deposition of low resistivity traces on high performance additively manufactured all-aromatic polyimides (AM-PI) without the use of conductive inks. This is accomplished through the selective patterning of laser induced graphene (LIG), a porous 3D graphene fabricated via laser irradiation, onto the AM-PI. While the resultant LIG is conductive, its resistivity is further reduced by the electrodeposition of copper (Cu-LIG). In this thesis, the synthesis of LIG on AM-PI, thermally post processed to 240℃, 300℃, and 450℃, is demonstrated and characterized through sheet resistance measurements and Raman spectroscopy. AM-PI post-processed to 300℃ demonstrated the lowest sheet resistance LIG formation (13.8 Ω/square). The resistivity of Cu-LIG is compared to an industry standard silver ink (Micromax CB028) used in direct write hybrid manufacturing applications. Cu-LIG was found to have a measured resistivity (1.39e-7 Ω·m), two orders of magnitude lower than the measured resistivity of the CB028 silver ink (1.62e-5 Ω·m). Additionally, the thermal performance and current capacity of the Cu-LIG was demonstrated by observing resistive heating of the material under current load via IR thermography. Cu-LIG demonstrated no failure of conductive trace or substrate under 5A of current for 2 minutes, heating to a maximum recorded temperature of 76.3℃. Several multifunctional components were fabricated as case studies to further validate the process. A heater and an interdigitated capacitor are fabricated to demonstrate selective deposition of complex copper traces. The fabrication of an Archimedes spiral on a dome via Cu-LIG is completed to demonstrate the ability to use the process to fabricate conformal conductive traces. An LED circuit is fabricated on an AM-PI lattice which demonstrates multi-planar fabrication on geometrically complex 3D printed substrates.

The main objective of this study was to determine the applicability of advanced water treatment processes namely granular activated carbon (GAC) adsorption, ultraviolet (UV) light disinfectant and ozone in the management of deteriorating water quality in the Mid-Vaal River system for drinking purposes. Both the scarcity and the deteriorating quality of water in South Africa can be addressed by investigating advanced water treatment processes such as GAC adsorption, UV light disinfectant and ozone. Previously disregarded water resources have the potential to be purified and advanced treatments can improve water quality where conventional water treatments have failed. In addition, advanced treatment processes can be applied to treat used water. The two sampling sites selected for the study, Rand Water Barrage (RWB) and Midvaal Water Company (MWC), are both located in the Middle Vaal Water Management Area with RWB upstream of MWC. RWB uses GAC adsorption and UV light disinfection and MWC uses ozone as pre- and intermediate treatment process steps for water purification. The quality of the source water at both sampling sites was determined by analysing the physical and chemical characteristics as well as the algal and invertebrate compositions of the source water. The physical and chemical water quality variables measured included pH, conductivity, turbidity, dissolved organic carbon (DOC), total organic carbon (TOC), total photosynthetic pigments (TPP), microcystin and geosmin. The source water of both sites was characterised as hypertrophic on account of high chlorophyll concentrations. The water quality of the two sites was distinctly different and a downstream change was observed. The source water of RWB was characterised by high microcystin, geosmin, DOC, TOC and conductivity measurements and dominated by Bacillariophyceae (diatoms) and Cyanophyceae (blue-green bacteria). Problematic species that were present in the source water of RWB included Aulacoseira sp., other unidentified centric diatoms, Pandorina sp., Anabaena sp., Microcystis sp., Oscillatoria sp., Cryptomonas sp., Ceratium sp. and Trachelomonas sp. The source water of MWC was characterised by high pH, turbidity and TPP measurements and was dominated by Chlorophyceae (green algae) and Bacillariophyceae (diatom) species. Problematic algal species that were present in the source water of MWC included Cyclotella sp., Coelastrum sp., Pediastrum sp. and Scenedesmus sp. The source water of MWC was deemed to be of a better quality due to the lower Cyanophyceae concentrations and lower microcystin levels. The invertebrate composition of both sites was similar with Rotatoria as the dominant invertebrate group. The efficacy of GAC adsorption/UV light disinfection/ozonation on restoring the physical and chemical characteristics of the source water at both sampling sites as well as the algal and invertebrate compositions was determined by ascertaining the nature of the change in or the percentage removal of a water quality variable. The potable water of both sites complied with the standards of water intended for domestic use except for the conductivity at RWB that was slightly elevated. The phytoplankton was removed effectively from the source water of both sites but the removal of invertebrates was unsatisfactory. GAC adsorption and filtration proved to be more effective in the removal of TPP, turbidity, DOC, microcystin and geosmin than ozone. Ozone effected an increase in DOC. UV light disinfection had no or little effect on restoring the water quality variables investigated in this study. / M (Environmental Sciences), North-West University, Potchefstroom Campus, 2015

The main objective of this study was to determine the applicability of advanced water treatment processes namely granular activated carbon (GAC) adsorption, ultraviolet (UV) light disinfectant and ozone in the management of deteriorating water quality in the Mid-Vaal River system for drinking purposes. Both the scarcity and the deteriorating quality of water in South Africa can be addressed by investigating advanced water treatment processes such as GAC adsorption, UV light disinfectant and ozone. Previously disregarded water resources have the potential to be purified and advanced treatments can improve water quality where conventional water treatments have failed. In addition, advanced treatment processes can be applied to treat used water. The two sampling sites selected for the study, Rand Water Barrage (RWB) and Midvaal Water Company (MWC), are both located in the Middle Vaal Water Management Area with RWB upstream of MWC. RWB uses GAC adsorption and UV light disinfection and MWC uses ozone as pre- and intermediate treatment process steps for water purification. The quality of the source water at both sampling sites was determined by analysing the physical and chemical characteristics as well as the algal and invertebrate compositions of the source water. The physical and chemical water quality variables measured included pH, conductivity, turbidity, dissolved organic carbon (DOC), total organic carbon (TOC), total photosynthetic pigments (TPP), microcystin and geosmin. The source water of both sites was characterised as hypertrophic on account of high chlorophyll concentrations. The water quality of the two sites was distinctly different and a downstream change was observed. The source water of RWB was characterised by high microcystin, geosmin, DOC, TOC and conductivity measurements and dominated by Bacillariophyceae (diatoms) and Cyanophyceae (blue-green bacteria). Problematic species that were present in the source water of RWB included Aulacoseira sp., other unidentified centric diatoms, Pandorina sp., Anabaena sp., Microcystis sp., Oscillatoria sp., Cryptomonas sp., Ceratium sp. and Trachelomonas sp. The source water of MWC was characterised by high pH, turbidity and TPP measurements and was dominated by Chlorophyceae (green algae) and Bacillariophyceae (diatom) species. Problematic algal species that were present in the source water of MWC included Cyclotella sp., Coelastrum sp., Pediastrum sp. and Scenedesmus sp. The source water of MWC was deemed to be of a better quality due to the lower Cyanophyceae concentrations and lower microcystin levels. The invertebrate composition of both sites was similar with Rotatoria as the dominant invertebrate group. The efficacy of GAC adsorption/UV light disinfection/ozonation on restoring the physical and chemical characteristics of the source water at both sampling sites as well as the algal and invertebrate compositions was determined by ascertaining the nature of the change in or the percentage removal of a water quality variable. The potable water of both sites complied with the standards of water intended for domestic use except for the conductivity at RWB that was slightly elevated. The phytoplankton was removed effectively from the source water of both sites but the removal of invertebrates was unsatisfactory. GAC adsorption and filtration proved to be more effective in the removal of TPP, turbidity, DOC, microcystin and geosmin than ozone. Ozone effected an increase in DOC. UV light disinfection had no or little effect on restoring the water quality variables investigated in this study. / M (Environmental Sciences), North-West University, Potchefstroom Campus, 2015