Paper that is subjected to moisture undergoes dimensional changes. It expands during moistening and shrinks during drying. When the paper is under tension between rollers, the effects are complex since shrinkage and expansion are restricted in the width direction. Waves can then appear on the paper web. This can be a problem in heatset web offset printing. The problem is known as waviness or fluting. The printed papers exhibit a wavy shape, which is visually disturbing due to light reflections which create glossy streaks. The aim of the work described in this thesis was to develop a method suitable for studying the moisture- and tension-induced waviness. Experiments were carried out on a laboratory scale to study how such waves develop during moistening and drying. The experimental setup was based on a modified tensile tester. A CCD camera and image analysis based on the STFI-OptiTopo technique was used to characterise the waviness. Moistening and drying were achieved by changing the surrounding air humidity. The method was used to study the effect of moisture uptake by the paper, and to evaluate the effect of tension on the waviness. It was found that increasing moisture resulted in a higher waviness amplitude, but that the web tension controlled the wavelength of the waviness. A high tension gave rise to a shorter wavelength. The measured wavelength was compared with a previously suggested model and the predicted wavelength was about twice as high as the measured wavelength. / When paper becomes damp it can develop waves which can be a problem with heatset web offset printing. Paper with waves may have glossy streaks after printing. Laboratory experiments studied the effect of moisture uptake by the paper. Readings were taken at a range of air humidities. The effect of tension on the waviness was also measured. The waviness was characterised using a charge coupled device (CCD) camera and the STFI-Packforsk OptiTopo technique to analyse the images. When the humidity was increased the amplitude of the waves increased. A high tension resulted in shorter wavelengths. Results from a previous model were used as a comparison.

Research on freeze-thaw resistance of concrete in general and on curing and moisture conditions in particular is motivated from an economic and product sustainability point of view. Specifically, it is argued for the importance of considering the effect of curing and test exposure conditions on the moisture uptake and performance during freeze-thaw. Due to the demonstrated importance of moisture conditions on performance, they should be related to those of field service conditions when choosing a test procedure in a particular case. This is vital for adequate testing of new and more sustainable concrete materials.

An increasing number of power plants in Scandinavia are beginning to use biofuel instead of coal or oil. The material in the new fuel is a mixture of woodchips, mostly Pine, Spruce and Salix, bark, GROT (tops and branches from felling waste) and sawdust from sawmills. It is heterogeneous, having a moisture content varying from 15% up to 65%. The moisture content affects the combustion of the fuel and therefore its commercial value. The industry is now interested in obtaining a method for measuring the moisture content of biofuel, quickly and reliably; preferably on delivery at the power plant. The measuring technique presented in this thesis is the first reported in the literature capable of measuring the moisture content of a large sample of such an heterogeneous material as biofuel. The equipment is today calibrated for a sample volume of 0.1 m3. A radio frequent signal is supplied from an antenna and penetrates the biofuel. Its reflection is modeled using partial least squares. As part of the work presented in this thesis, a new type of measuring rig and an analysis method for measurement of the moisture content of large samples of heterogeneous material have been developed. A statistical model for moisture content measurements of five different biofuel materials using radio waves has been built, having a root mean square error of prediction of 2.7. The interactions between biofuels and radio frequent signals have been demonstrated, indicating a variation of the reflection with varying types of biofuel material and variation in the reflection and delay of the signal with varying moisture content.

Vattenhaltsbestämning är av stor vikt i många sammanhang. T.ex. kan vattenhalten påverka utbytet av en kemisk syntes, eller ha negativ inverkan på hållbarheten av läkemedel och livsmedel. Standardmetoden för vattenhaltsbestämning är Karl Fischer-titrering, baserad på antingen volymetri eller coulometri. I den här avhandlingen presenteras nya infallsvinklar för bestämning av mycket låga halter vatten i komplexa provmatriser, som t.ex. tekniska oljor och substanser som interfererar med alkoholbaserade Karl Fischer-reagens. Vattnet avskiljs ofta från oljematrisen före titrering genom förångning. I samband med framtagningen av nya referensmaterial för vatten i olja ifrågasattes förångningsteknikernas effektivitet av National Institute of Standards and Technology (NIST). NIST menade att en fraktion av vattnet bands hårt i oljefasen och att det inte kunde frigöras och detekteras annat än med en modifierad volymetrisk metod där reagenset innehöll minst 65% kloroform. I den här avhandlingen presenteras en alternativ metod som uppfyller det ställda kravet för en fullständig upplösning av oljefasen. Med denna metod visas att det inte finns någon anledning att ifrågasätta förångningsteknikernas effektivitet och att den modifierade metoden som NIST använder ger systematiskt för höga resultat. Fördelar som enklare handhavande, kortare konditioneringstider och att endast ett reagens behövs har gjort att diafragmafri coulometri har blivit allt mer populär. Spårhaltsbestämning med denna teknik ställer dock speciellt höga krav på reagensen eftersom strömtätheten vid katoden är låg. Med anledning av detta testades olika typer av kommersiella reagensblandningar för bestämning av små vattenmängder och kritiska parametrar identifierades. Dekanol visade sig ha en gynnsam effekt på katodreaktionen i reagens modifierade med xylen enligt standardmetodbeskrivningen för bestämning av vatten i oljor. För provtyper som inte går att analysera med alkoholbaserade reagenser presenteras en ny typ baserad på N-metylformamid. Med ett sådant reagens bestämdes vattenhalten i ett reaktivt salt som används i litiumjonbatterier. Liknande alkoholfria reagens undersöktes mer utförligt i en djupare studie som även inkluderade formamid och dimetylformamid. För- och nackdelar med dessa alternativa lösningsmedel diskuteras och möjliga reaktionsförlopp föreslås. Det visade sig att läget på jämvikten mellan svaveldioxid och vätesulfit är en avgörande faktor för att förklara den stora skillnaden i reaktionshastighet i dessa lösningsmedel. / Moisture determination is of great importance in the production and use of many substances. For example, the moisture content can affect the efficiency of a chemical reaction or determine the shelf life of pharmaceuticals or foods. The standard method for moisture determination is Karl Fischer (KF) titration, based on either volumetry or coulometry. This thesis concerns new approaches to trace determination in complex sample matrices and is focused on oils and substances that interfere with alcoholic KF reagents. Moisture is frequently separated from oil matrices before titration by means of evaporation techniques. In connection with the preparation of new reference materials for moisture in oil, the National Institute of Standards and Technology (NIST) questioned the efficiency of such evaporation techniques. NIST claimed that some of the moisture was sequestered in the oil phase and that it could only be released and detected by using a modified volumetric KF method with a reagent containing at least 65% chloroform. In this thesis, an alternative KF method that meets the proposed requirement for a complete dissolution of the oil sample is presented. With this method it is shown that there is no reason to question the efficiency of the evaporation techniques and that the criticized volumetric method used by NIST is biased high. Ever since its introduction diaphragm-free coulometry has gained popularity due to its ease of use, with a single reagent and short conditioning times. Trace determination with this technique sets great demands on the reagent due to the resulting low current densities at the generator cathode. The performance of several commercial reagents is evaluated under such unfavorable conditions and critical titration parameters are identified. It is also shown that decanol has a favorable effect on the cathode process when using reagents modified with xylene according to standard methods for moisture determination in oils. For samples that are incompatible with the alcohol component in ordinary KF reagent a new reagent based on N-methylformamide is presented. It is shown that is works well for determinations of moisture in a conductive salt used in lithium-ion batteries. The concept of alcohol-free KF reagents is taken a step further in a systematic investigation, also including formamide and dimethylformamide. Advantages and disadvantages with these solvents are discussed and possible reaction paths are surveyed. It is shown that the position of the sulfur dioxide/hydrogen sulfite equilibrium is the main explanation for the large differences in the KF reaction rates in these solvents.

Graduation date: 1992

Abstract Drought is the most common abiotic stress limiting chickpea production in the world. Ninety percent of the worlds chickpea is produced in areas relying upon conserved, receding soil moisture, therefore, crop productivity is largely dependent on efficient utilization of available soil moisture. Because of the variability in drought pattern from year to year, trait based selection could have an advantage over selection on the basis of grain yield alone. Trait based breeding, however, requires trait dissection into components. Successful marker identification would facilitate integration of MAS procedures in breeding programs enabling the pyramiding of favourable alleles.<p> The genetic map produced in this study was based on a population of recombinant inbred lines of a cross of ILC 588 x ILC 3279 containing 52 SSR markers spanned 335 cM of the chickpea genome at an average density of 6.4 cM. A total of 13 genomic regions were shown to be associated with drought tolerance traits. Some of these genomic regions showed pleiotropic effect on multiple traits. This was also supported by the analysis of phenotypic data where these traits were found to be correlated. For example, early flowering and maturity had a strong association with high grain yield. High grain yield was also associated with better portioning ability between biomass and grain yield, i.e. harvest index. Drought tolerance score (DTS) was associated with various important traits including biomass, early flowering, early maturity.<p> This study also concluded that chickpea genotypes differed in terms of root length, root length density, root weight density and root length to weight ratio at every 20 cm soil layer up to 100 cm depth in response to water deficits. Consideration of an efficient root system vs. a larger root system is also important, since in this research, large root systems were offset by low harvest index, presumably due to the lack of assimilate available for grain growth. A restricted root system is important in environments like Western Canada, where crop growth termination is usually required prior to fall frost. This study also reported significant associations of stomatal conductance (gs) with each of HI, grain yield under drought, drought susceptibility index and drought tolerance score (DTS). Stomatal conductance can also be used to assess plant stress due to drought. Values of gs less than 250 mmol m-2s-1 during flowering indicated drought stress under greenhouse conditions. A higher degree of plant stress due to drought was shown by increased stomatal closure at midday (gs <150 mmol m-2s-1). The study of 157 RILs under natural drought stress during 2005-07 revealed that the 17 RILs which had high grain yield under drought (Group A), also tended to have higher gs than the 42 RILs that had lower grain yield (Group B). Group A had mean gs values of 390 mmol m-2s-1 during the week before flowering, while Group B had mean gs value of 330 mmol m-2s-1. Stomatal conductance increased at flowering and then sharply decreased later in the reproductive period, particularly in Group B. These findings were also supported by canopy temperature differential measurements as Group A was also able to maintain lower canopy temperature than Group B, indicating the ability of these plants to maintain adequate transpiration and a cooler canopy under drought stress. This research indicated that gs and canopy temperature can be used to assess chickpea drought stress and to screen drought tolerant genotypes. This study identified a QTL on LG7 for gs, QTLs on LG1, LG3 and LG6 associated with canopy temperature differential, as well as QTLs associated with grain yield under drought, HI, DTS, days to flower, days to maturity, reproductive period and plant height. These QTLs identified for traits related to higher chickpea productivity under drought stress could have important implications for accelerating the process of pyramiding of favourable genes into adapted genotypes and on future marker-assisted breeding for drought prone areas.

The mining of oil sands in the sub-humid region of Northern Alberta, Canada causes large-scale landscape disturbance, which subsequently requires extensive reclamation to re-establish the surface and subsurface hydrology. The reconstructed watersheds examined in this study are located at the Syncrude Canada Limited mine site, 40 km North of Fort McMurray, Alberta, Canada. The three experimental reconstructed watersheds, with nominal soil thicknesses of 1.0 m, 0.50 m and 0.35 m comprised a thin layer of peat (15-20 cm) over varying thicknesses of secondary (till) soil, have been constructed to cover saline sodic overburden and to provide sufficient moisture storage for vegetation while minimizing surface runoff and deep percolation to the underlying shale overburden. In order to replicate the hydrological behavior, assess the sustainability, and trace the evolution over time of the reclaimed watersheds, a suitable modeling tool is needed.</p> <p>In this research, a model is developed using the system dynamics approach to simulate the hydrological processes in the three experimental reconstructed watersheds and to assess their ability to provide the various watershed functions. The model simulates the vertical and lateral water movement, surface runoff and evapotranspiration within each watershed. Actual evapotranspiration, which plays an important role in the hydrology of the Canadian semi-arid regions, is simulated using an indexed soil moisture method. The movement of water within the various soil layers of the cover is based on parametric relationships in conjunction with conceptual infiltration models. The feedback relationships among the various dynamic hydrologic processes in the watershed are captured in the developed System Dynamic Watershed Model (SDWM). </p> <p>Most hydrological models are evaluated using runoff as the determining criterion for model calibration and validation, while accounting for the movement of moisture in the soil as a water loss. Since one of the primary objectives of a reconstructed watershed is to maintain the natural flora and fauna, it is important to recognize that soil moisture plays an important role in assessing the performance of the reconstructed watersheds. In turn, soil moisture becomes an influential factor for quantifying the health of the reconstructed watershed. The developed model has been calibrated and validated with data for two years (2001-2002), upholding the sensitive relationship between soil moisture and runoff. Accurate calibration of the model based on simulations of soil moisture in the various soil layers improves its overall performance. The model was subsequently used to simulate the three sub-watersheds for five years, with changing the calibrated model parameters to use them as indicators of watershed evolution. The simulated results were compared with the observed values. </p> <p>The results of the study illustrate that all three watersheds are still evolving. Failure to identify a unique parameter set for simulating the watershed response supports the hypothesis of watershed evolution. Soil moisture exchange between the till and peat layers changed with time in all of the watersheds. There was also a modest change in the water movement from the till to shale layers in each of the sub-watersheds. Vegetation is increasing in all of watersheds although there is an indication that one of the sub-watersheds may be sustaining deep rooted vegetation. The results demonstrate the successful application of the system dynamics approach and the developed model in simulating the hydrology of reconstructed watersheds and the potential for using this approach in assessing complex hydrologic systems.

Urea is an important nitrogen fertilizer for plant nutrition, but is very susceptible to moisture sorption and caking even at low moisture contents, e.g. 0.25% w/w. When urea particles adsorb moisture followed by drying, crystal bridges form between urea particles. For particles in a bed, this process is called caking. Cakes in stored urea cause a degradation of its quality and value. Investigations of the moisture absorption in beds of manufactured urea particles and adsorption on the external and internal surfaces of urea particles are a necessary step if engineers are to recommend procedures to reduce caking and control inventories. Research on moisture adsorption and cake strength of urea fertilizer has not been sufficiently explored. Only recently have researchers started to devise tests to investigate the crystal bonding between two urea particles. Prior to this research, investigations of the moisture interactions in beds of urea were nearly non-existent. This thesis presents experimental, theoretical and numerical methods to investigate the coupled heat and moisture transfer processes in a bed of urea particles while the bed is exposed to ambient air with changing temperature and humidity.<p> Urea particles are nearly spherical with uniform particle size distribution. The particle size, its internal pore structure and rough crystalline external surface depend on the manufacturing process. In this thesis, two types of urea products are investigated, i.e. prill Georgia urea and granular Terico urea. The rough external surface and internal pore structure of each particle makes the total surface area exposed to water much larger than similar smooth and solid spherical particles. Although Georgia urea has higher external surface area than Terico urea, the latter type has larger total surface area and internal pore volume. For both Terico urea and Georgia, the internal surface area dominates the water sorption process but the external moisture sorption of Georgia urea is more important than that of Terico urea.<p> All the water vapor interaction experiments were carried out with air flow through a test bed because it shortens the duration of each experiment to a few hours in most cases. A series of experiments with step changes in inlet air temperature and humidity for air flow through a urea bed indicated that the measured outlet air temperature and humidity responses, each at a specific air flow rate, reveals a typical exponential or transient time change that can be characterized by a time constant. After formulating the theoretical problem for step changes in the inlet properties, the analytical solutions showed that the time constants of outlet response to whether a temperature step change or a humidity step change are functions of the convection coefficient and air velocity. The predicted outlet air temperature is determined by only one time constant for a temperature step change while it is determined by these two time constants for a humidity step change.<p> A new test cell with sampling test ports was developed to measure the transient moisture uptake of a urea particle bed and its distribution at any time without any interruption of the experiment. A novel particle sampling device, modified from a syringe and pistons, was designed to minimize the particle exposure to ambient air during the moisture content determination using a Karl Fischer titrator. Data from two continuous cyclic step changes in the inlet flow with relative humidities between 4% and 70% at room temperature showed a hysteresis in the isothermal moisture content for only the first cycle. After the second sorption- desorption cycle, the hysteresis disappeared. This implies that the internal pore and particle surface geometry changes are very slow after the first cycle.<p> A new theoretical porous media model was developed for a coupled heat and moisture transport process when humid air flowed uniformly through a large test bed in two coupled computational domains: internal domain (i.e., the particle phase) and the external domain (i.e., the interstitial air space). The moisture migration in two computational domains included: water vapor diffusion inside each particle, and water vapor convection and diffusion in the interstitial air space in the urea particle bed. For energy transport, the temperature was assumed to be uniform inside each particle, but heat convection and conduction between the urea particles and the interstitial air outside particles occurred throughout the bed. Both heat transfer and mass transfer in internal domain and external domain were coupled by the heat and mass convection at the gas-particle interface. The numerical simulation was compared with the data of moisture uptake and showed good agreement implying that the internal moisture diffusion that dominates the moisture uptake process is a very slow process.<p> These above experimental, theoretical and numerical research studies provide a set of information on how urea particles adsorb or desorb moisture from or to ambient air on the external and internal pore surface, which offers a useful suggestion for urea caking prevention and is also a first and necessary step to the study of further caking formation and strength.

In this study, a numerical model is developed for determining coupled heat and moisture transfer in a run-around membrane energy exchanger (RAMEE) using two counter/cross flow exchangers and with a salt solution of MgCl2 as the coupling fluid. The counter/cross flow exchanger is a counter-flow exchanger with cross-flow inlet and outlet headers. The model is two-dimensional, steady-state and based on the physical principles of conservation of momentum, energy, and mass. The finite difference method is used in this model to discretize the governing equations.<p> The heat transfer model is validated with effectiveness correlations in the literature. It is shown that the difference between the numerical model and correlations is less than ¡À2% and ¡À2.5% for heat exchangers and run around heat exchangers (RAHE), respectively. The simultaneous heat and moisture transfer model is validated with data from another model and experiments. The inter-model comparison shows a difference of less than 1%. The experimental validation shows an average discrepancy of 1% to 17% between the experimental and numerical data for overall total effectiveness. At lower NTUs the numerical and experimental results show better agreement (e.g. within 1-4% at NTU=4).<p> The model for RAHE is used to develop new effectiveness correlations for the geometrically more complex counter/cross flow heat exchangers and RAHE systems. The correlations are developed to predict the response of the exchangers and overall system to the change of different design characteristics as it is determined by the model. Discrepancies between the simulated and correlated results are within ¡À2% for both the heat exchangers and the RAHE systems.<p> It is revealed by the model that the overall effectiveness of the counter/cross flow RAMEE depends on the entrance ratio (the ratio of the length of the inlet and outlet headers to the length of the exchanger, xi/x0), aspect ratio (the ratio of the height to the length of the exchanger, y0/x0), number of heat transfer units (NTU), heat capacity rate ratio (Cr*), number of mass transfer units (NTUm), and the mass flow rate ratio of pure salt in desiccant solution to dry air (m*). Beside these dimensionless parameters, the performance of the RAMEE system is affected by the liquid-air flow configuration and the operating inlet temperature and humidity.<p> This study concludes that the maximum effectiveness of the RAMEE system with two counter/cross flow exchangers occurs when NTU and NTUm are large (e.g. greater than 10). At any NTU, the overall effectiveness of the RAMEE system increases with Cr* until it reaches a maximum value when Cr*= . Increasing Cr* above causes the overall effectiveness to decrease slightly. Therefore, to achieve the maximum overall effectiveness of the system, Cr* must be close to . is a function of NTU and operating conditions e.g., with NTU=10, and under AHRI summer and winter operating conditions, respectively. The exchangers in the RAMEE system are needed to have a small aspect ratio (e.g. y0/x0<0.2) and small entrance ratio (e.g. xi/x0<0.1) to get the maximum overall effectiveness of a RAMEE system using two counter/cross flow exchangers. Such a RAMEE system has a total effectiveness 6% higher and 1.5% lower compared to the same cross-flow and counter-flow RAMEE, respectively (at NTU=10, Cr*¡Ö3, y0/x0=0.2 and xi/x0=0.1).

This thesis contains the numerically investigations of the performance of a run-around membrane energy exchanger (RAMEE) at different outdoor air conditions and the effects of non-uniform exchanger channels. The RAMEE is a new type of building ventilation air energy recovery system that allows heat and moisture to be transferred between isolated supply and exhaust air streams. Two liquid-to-air membrane energy exchangers (LAMEEs) are placed in the supply and exhaust air ducts and transfer heat and moisture between air and a circulating liquid desiccant that couples the two LAMEEs together. The ability of the system to transfer heat and moisture between isolated supply and exhaust ducts makes it appropriate for numerous HVAC applications (e.g., hospitals and building energy retrofits). <p> The performance of the RAMEE at different outdoor air conditions is shown to be highly variable due to the coupling of the heat and moisture transfer by the desiccant. This coupling allows the humidity ratio between the indoor and outdoor air to influence the heat transfer and the moisture transfer is influenced by the difference between the indoor and outdoor air temperatures. The coupling produces some complex RAMEE performance characteristics at some outdoor air conditions where the effectiveness values (i.e., sensible, latent, and total) were shown to be less than 0% or greater than 100%. Effectiveness and operating correlations are developed to describe these complex behaviours because existing correlations do not account for the coupling effects. The correlations can serve as design and operation tools for the RAMEE which do not require the use of an iterative computational numerical model.<p> Non-uniform exchanger channels are present in the RAMEE because of pressure differences between the air and solution channels which deform the membrane into the air channel. The non-uniform channels are analytically shown to create maldistributed fluid flows and variable heat and mass transfer coefficients. The combined effects of these two changes lead to a reduction in the RAMEE effectiveness, which increases as the size of the membrane deformation increases. The reduction in total effectiveness for an exchanger where the membrane has a peak deflection of 10% of the nominal air channel thickness operating at a NTU of 12 was shown to be 12.5%. These results of non-uniform exchanger channels agree with previously conducted experimental results.