Anthropogenic emission of greenhouse gases has long been suspected to contribute to global warming and climate change. Most greenhouse gases are emitted in a mixture, so efficient methods and materials to separate and capture the gases are in demand in order to reduce emissions. A promising material group for this purpose is metal-organic frameworks (MOFs). This class of material have the ability to selectively adsorb green house gases due to its high porosity and high surface area. Zeolitic imidazolate frameworks (ZIFs) are a subclass of MOFs that are topologically similar to zeolites and are known for their good chemical and thermal stability.   The aim of this project was to investigate if the greenhouse gas (i.e. CO2 and SF6) capture performance of ZIFs could be improved and tuned using a mixed-linker approach with seven different imidazolate-based organic linkers of different sizes or with various functional groups. As well as to investigate the processability of MOFs using 3D printing. ZIFs composed of different ratios of 2-methylimidazolate as base linker and a second linker of imidazolate, benzimidazolate, 2-aminobenzimidazolate, 5,6-dimethylbenzimidazolate, and 4,5-dichloroimidazolate were succesfully made. The materials were all found to be crystalline, however, mixed-linker ZIFs containing 2-aminobenzimidazole, 5,6-dimethylbenzimidazole and dichloroimidazole were observed to contain more than a single phase. All samples showed to be somewhat porous towards CO2 and SF6, and there seem to be a trend where a low % of a bulkier linker (eg. bIm, ambIm) resulted in a higher uptake of SF6 whereas a high % resulted in a higher uptake of CO2. For dcIm it was the other way around, a low % showed a higher uptake for CO2  whereas a high % showed a higher uptake for SF6. For CO2, the ZIF containing 80% benzimidazolate showed the highest uptake of 9.81 wt%. For SF6, the 25% 4,5-dichloroimidazolate showed the highest uptake of 17.73 wt%. Furthermore, direct ink writing (DIW) 3D printing was also successfully utilized to process and structure a Mn-based MOF using carbopol as binder. The printed structure was found to have similar properties to the pristine MOF in regards to crystallinity and porosity.

The precise control of the resonance frequency of plasmonic nanostructures is critical and depends on the size, composition, shape, and dielectric nature of the environment. The ability to control the shape and size of nanomaterials acutely depends on the fabrication technique and material design. We used a cheap and scalable method known as nanosphere lithography (NSL) to fabricate plasmonic nano-prism (NP) on glass and indium tin oxide substrate (ITO). The methods involve substrate hydrophilicity treatment, polystyrene nanosphere masking, metal deposition, and mask removal. The array and specific morphology of the fabricated NP was established using scanning electron microscope (SEM) and atomic force microscope (AFM). Finally, we used UVVis spectroscopy to determine the plasmonic resonance frequencies of fabricated NP on different substrates. The results reported herein have potential applications in surface-enhanced Raman spectroscopy (SERS), and biosensing. We also used scanning tunneling microscope to obtain high spatial resolution images of supramolecular trigrams.

Fem metoder har använts för att modifiera barrvedslignin med syftet att öka reaktiviteten av ligninet mot epoxidgrupper. Ligninprover analyserades med NMR och FTIR medan reaktivitet var mätt genom reometri. Metoder som ökade mängden karboxylsyragrupper på ligninet minskade ligninets reaktivitet. Modifikation av lignin med resorcinol minskade reaktiviteten medan modifikation med fenol ökade reaktivitet mot epoxidgrupper. / Five different methods were used to modify softwood kraft lignin with the goal of increasing the reactivity of lignin towards epoxide groups. Lignin samples were characterized with NMR and FTIR while reactivity was measured through rheometry. Methods that increased carboxylic acid content in lignin decreased reactivity. Lignin modification with resorcinol decreased reactivity while lignin modified with phenol increased reactivity.

This work expands the current understanding of materials chemistry and engineering capabilities of two synthetic platforms: 1.) bis-ortho-diynylarenes (BODA) and 2.) trifluorovinylaryl ethers (TFVE). Each platform possesses a unique chemistry which paradoxically enables the development of high-performance materials therefrom while simultaneously retaining exceptional melt and solution processability. Leveraging the apparent dichotomy in properties (performance/processability) obtainable from these two synthetics platforms, we have pursued and achieved a practical approach to high-temperature resistant materials with an immense potential for technology transfer and commercialization: 1.) BODA-derived resins (BDR) constitute a versatile platform of melt-processable resins capable of rapidly producing high performance matrix composites which include thermoset, carbon-carbon, and other specialty carbon or hybrid ceramic composite structure. BODA monomers can be synthesized via a three-step process from commercially available bisphenols and undergo a facile catalyst-free, thermal-initiated polymerization to yield polyarylene thermosets with outstanding thermal-oxidative stability, low heat release, flame resistance, and high carbon yields (>80%). The combination of melt processability, ease of cure, and high carbon yields in BDR provides an attractive quick, single-step fabrication of carbon/carbon (C/C) composites with excellent interlaminar shear strength (ILSS; ~1800 psi) after a single infusion/carbonization. Furthermore, our work in this area has shown that C/C from BDR can be prepared via a fast carbonization (10 °C/min), relative to typical 1 °C/min or 1 °C/hr industrial carbonizations, without causing undesirable shrinkage, cracking, interlaminar debonding, or detrimental changes in ILSS. 2.) Large polyaromatic hydrocarbons (PAHs) are typically known for their interesting thermal- and photo-optical properties but suffer from poor solubility and processability issues. Functionalization of these moieties with TFVE fluorocarbon groups enables melt or solution polymerization via a thermally initiated [2+2] cyclodimerization of the TFVEs towards high performance perfluorocyclobutyl (PFCB) aryl ether polymers. For example, successful fabrication of free-standing photoluminescent films with record high glass transition temperatures (Tg ~ 300 °C), exceptional thermal-oxidative stability (~250 °C, 24 h), unprecendented photostability at 250 °C in air, and excellent solubility in common organic solvents (at room temperature) have been realized via a set of triphenylene-enchained PFCB aryl ether polymers.

The increasing energy demand requires a transition from fossil fuels to renewable resources. Lithium-ion batteries (LIBs) offer a promising solution as efficient energy storage devices. However, the aluminum current collector (CC) in LIBs is susceptible to anodic dissolution above 3 V vs. Li+/Li in commercial carbonate liquid electrolytes, compromising the battery performance. In this study, various approaches were explored to mitigate anodic dissolution in LiFSI EC:DEC at high voltages of the aluminum CC in LIBs, employing cyclic voltammetry (CV) and scanning electron microscopy (SEM). It was found that boiling the Al foil in water in an air atmosphere to increase the thickness of the surface Al2O3 layer improved the anodic stability and offered enhanced protection against proton attack (due to the oxidation of the carbonate solvent at high voltage). However, increasing the LiFSI electrolyte concentration to 2 M did not increase the anodic stability due to the absence of a passivating AlF3 layer. Notably, in 4 M LiFSI, impurity-induced high F- concentration facilitated the formation of a passivating AlF3 layer, resulting in improved anodic stability. Moreover, specific volume ratios of LiFSI EC:DEC and 1 M LiPF6 EC:DEC (1:1) (LP40) yielded the F- concentration necessary for forming a passivating AlF3 layer and significantly enhanced the anodic stability. On the other hand, carbon-coating the Al foil did not show significant improvements regarding the anodic stability. It was found that the corrosion was time-dependent at a low scan rate, a drastic anodic dissolution of the aluminum was seen at higher temperatures, and the corrosion also became more pronounced. At room temperature, carbon-coated Al foils exhibited increased stability.

In today’s fast adjustment to renewable energy, new battery technologies are needed to meetthe ever-growing demands of energy storage. Cheaper and easier to produce materials areneeded, as well as materials with a lower environmental impact. One new and interestingtechnology is the dual-ion battery, and more specifically the aluminum dual-ion battery. Thisbattery uses cheap and abundant aluminum together with a graphitic cathode to work. However,a lot of research today uses expensive and sophisticated cathode materials to make this type ofbattery work. Therefore, this thesis focuses on creating a cheap and easy to produce graphitecathode material through the phase inversion method for the use in aluminum dual-ionbatteries, that is also freestanding for better energy density. Graphene is also used as anadditive to improve the electrical conductivity of the material, and the material is later tested in afull cell with the typical ionc liquid electrolyte EMImCL/AlCl4.Through phase inversion, a freestanding graphite cathode is produced with 8 wt% PVDF binderand 0.4 wt% graphene. The material has a porous structure and an enhanced electricalconductivity with the graphene added. Through CV cycling and symmetric Al-Al tests the batteryreactions are shown to work. However, when cycling the cell with a constant current there areproblems, probably coming from some sort of soft shorting or side reactions. It is revealed thatapart from the expected reactions, Ni dissolution from the contact tabs also takes place, andmay cause problems. Further tests are needed to validate if this material works. However,because no new active materials have been introduced to the battery chemistry, it is reasonableto believe that the battery will work with some small changes.Tek nisk-naturvetensk apliga fak ulteten, Upps ala universitet. Utgiv nings ort U pps al a/Vis by . H andledare: Anwar Ahniy az , Äm nesgranskar e: D aniel Brandell, Ex aminator: Lena Klintberg

<p dir="ltr">Nonconjugated radical polymers and small molecules are employed as electrically conducting materials in multiple organic electronic devices, including electrolyte-supported devices and solid-state electronic devices, because of their charge transport and redox-active properties. In fact, macromolecules with nonconjugated backbones and stable radical pendent groups can have impressive charge transport capabilities (i.e., thin-film conductivities of ~20 S m^-1) if proper molecular design principles are employed.</p><p dir="ltr">In the first part of this work, a polysiloxane-based polymer bearing galvinoxyl radical groups has been synthesized. Density functional theory (DFT) calculations predicted that the spin delocalization behavior of the galvinoxyl group would result in a higher charge transfer rate compared with nitroxide radical systems. It is determined that the flexible backbone endowed the polymer with a glass transition temperature around 0 ℃, and this feature allowed the radical moieties to pack into conductive domains after thermal annealing. Furthermore, the conductivity of this radical polymer was quantified to be ~ 10^-1 S m^-1 after being cast into a thin film. Thus, these studies provide a strategy to direct molecular packing and facilitate charge transport in radical polymers with delocalized open-shell sites, which can aid in deciphering the charge transport mechanism in radical polymer thin films.</p><p dir="ltr">In the second part of this work, the charge transport and the magnetic properties of several nitroxide radical-based small molecules have been studied because 1) despite the success of nonconjugated radical polymers as solid-state charge conductors, the charge transport properties of nonconjugated open-shell small molecules have received less attention despite the fact that studying small molecule systems can facilitate the development of macromolecular radical conductors; 2) the unpaired electrons on these materials provide a means by which to respond to magnetic fields, making these materials promising candidates for organic magnets. Motivated by the need to develop open-shell small molecule materials, we quantify the electrical conductivity and magnetic properties in organic radical single crystals. Through proper molecular engineering of functional groups, we synthesized and crystallized a nitroxide radical-based material that has a single-crystal electrical conductivity of ~3 S m^-1, which is the highest values over 1 µm-scale for nonconjugated organic materials reported to date. Furthermore, we manipulate the molecular packing of the nitroxide radical molecules in the single crystals by introducing alkyl chains to the molecular structures. As a result, a strong antiferromagnetic ordering is obtained in the crystals with a Néel temperature of 40 K. In conclusion, new open-shell materials are developed with excellent charge transport capabilities and strong magnetic properties. This effort provides clear insights into designing the next-generation organic radical electrical conductors and magnetic materials.</p>

Water pollution is a profound ecological concern, exerting detrimental effects on human well-being, ecological systems, and animal life. Among the emerging contaminants that critically influence water quality and have garnered substantial scientific interest in recent times are per- and polyfluoroalkyl substances (PFAS). It is crucial to investigate the de- velopment of an easy technique for PFAS detection and measurement that can be used for quick analysis. This thesis explores the possibility to use amine-functionalized mesoporous carbon as an adsorbent to develop a detection method based on sequential adsorption of per- and polyfluoroalkyl substances (PFAS) and a dye, Rose Bengal, onto the adsorbent. The hypothesis is that the concentration of non-adsorbed dye is dependent on the amount of PFAS present, making the color intensity of the remaining solution proportional to the PFAS concentration. Mesoporous carbon was chosen as the adsorbent due to their high specific surface area, providing a high adsorption capacity, and the potential to functionalize the surface with amine groups which will attract the PFAS. Rose Bengal was selected as a concentration indicator as it has been shown that it can be used as a proxy for PFAS. In this study, the most prevalent PFAS compounds, namely PFOA and PFOS, were investigated. Prior to testing, the adsorbent underwent characterization using diverse techniques to show the porosity and particle morphology. The adsorption experiments encompassed varying PFAS concentrations and a range of dye solutions to determine the detection range, the powder-to-solution ratio necessary for discernible differentiation, and the adsorption or saturation time for both PFAS and dye. This thesis concludes that it was not possible to detect neither PFOA nor PFOS in the range of 0.1 pg/mL to 1 μg/mL with the setup, even though Rose Bengal adsorption could be detected down to 0.6 μg/mL. It was further observed that amine-functionalized hard templated mesoporous carbon has a higher adsorption capacity compared to the soft templated material.

No description available.

Metallic films are important in various applications, such as electric devices where it can act as contacts. In electrical devices, the substrate typically consists of silicon dioxide (SiO2) which is a temperature-sensitive substrate. Therefore, plasma enhanced chemical vapor deposition (PECVD) are better suited than thermally activated chemical vapor deposition (CVD). Depositing metallic films with PECVD demands co-reactants that act as reducing agents. However, these are not well-studied and do not always have the power enough to perform the reduction reaction for metals. Recently it has been concluded that electrons can act as reducing agents in the deposition of first row transition metallic films in a PECVD process. By supplying a positive bias to the substrate, the electrons got attracted to the surface of the substrate, which facilitated metal growth. The study concluded that metal growth only occurred at conductive -and semiconductive substrates and that the substrate bias and plasma power affected the metal growth. The process is however not well understood, which causes a knowledge gap, signifying that studies of the surface chemistry are needed. Here a new modified analytical method to study the surface chemistry in the newly developed process mentioned above is presented. The analytical method consists of an electrically modified quartz crystal microbalance (QCM) with gold electrodes as a conductive substrate. This allows the electron current to run through the QCM during the measurement. By supplying a DC-voltage to the front electrode it gets readily biased (negative and positive) and by placing a capacitor in the circuit, it connects the AC-circuit (oscillator circuit) and the DC-circuit (DC-voltage bias circuit). At the same time, it blocks the DC-current from going back to the oscillator but allows the high-frequency signal to pass from the QCM. The results in this thesis concluded that the QCM can be electrically modified to allow an electron flux to the QCM while using it as a substrate when electrons are used as reducing agents. Scanning electron microscopy (SEM) of a QCM crystal revealed that a 2 µm film had been deposited while SEM coupled with energy dispersive X-ray spectroscopy (EDS) showed that the film indeed contained iron. Further analysis was made by high-resolution X-ray photoelectron spectroscopy (HR-XPS) to find the elemental composition of the film, which revealed that the thin film contained 41 at.% iron. In addition, this study investigated if the QCM could be used to study CVD processes where electrons were used as reducing agents. The results indeed revealed that it is possible to study the surface chemistry where electrons are used as reducing agents with the electrically modified QCM to gain knowledge concerning film deposition. Initial results of the QCM showed that film growth could be studied when varying the plasma power between 5 W to 15 W and the QCM bias between -40 V to +40 V. The method generated easily accessible data concerning the process where electrons are used as reducing agents, which gained insight to the method that never has been disclosed before.