Foram desenvolvidos sistemas de medidas visando a caracterização de células solares de sílico monocristalino. Para isso, foram determinadas as características I x V no escuro para diferentes níveis de iluminação. Curvas de resposta espectral e capacitância em função da tensão inversa aplicada foram também obtidas. Foi feita uma avaliação do comportamento dessas células em função da temperatura e realizadas medidas de profundidade de junção utilizando-se três métodos distintos. Os principais parâmetros, que determinam o desempenho dessas células, foram obtidos boa concordância com a teoria e com os resultados apresentados na literatura. / Systems of measurements were developed for the characterization of single crystal silicon solar cells. For that, the curves I x V were measured in the dark and for different intensity of illumination. Curves of spectral response and of capacitance as a function of the reciprocal of the voltage were also measured. The behavior of the cells as a function of temperature was analysed and also measurements of junction depth were made by three different methods. Values for the parameters that characterize the cells were obtained, showing a good agreement with theoretical values and also with already reported values.

This thesis discusses the modeling of a micro-grid with photovoltaic (PV)-wind-fuel cell (FC) hybrid energy system and its operations. The system consists of the PV power, wind power, FC power, static var compensator (SVC) and an intelligent power controller. Wind and PV are primary power sources of the system, and an FC-electrolyzer combination is used as a backup and a long-term storage system. A simulation model for the micro-grid control of hybrid energy system has been developed using MATLAB/Simulink. A SVC was used to supply reactive power and regulate the voltage of the hybrid system. To achieve a fast and stable response for the real power control, the intelligent controller consists of a Radial Basis Function Network-Sliding Mode Control (RBFNSM) and a General Regression Neural Network (GRNN) for maximum power point tracking (MPPT). The pitch angle of wind turbine is controlled by RBFNSM, and the PV system uses GRNN, where the output signal is used to control the DC/DC boost converters to achieve the MPPT.

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / Este trabalho apresenta o estudo, desenvolvimento e aplicação de novas técnicas de controle aos sistemas de geração de energia fotovoltaica, conectados à rede elétrica monofásica, visando a melhoria da eficiência destes sistemas em relação aos métodos de controle tipicamente utilizados. O trabalho é dividido em duas partes principais, as quais estão relacionadas ao rastreamento do ponto de máxima potência (Maximum Power Point Tracking – MPPT) e, depois, ao controlador interno dos conversores boost-quadrático – lado dos painéis fotovoltaicos – assim como aos controladores do inversor de tensão, no lado da rede elétrica monofásica. A primeira parte do trabalho consiste no desenvolvimento de um algoritmo de meta heurística para o MPPT, o qual é baseado no método do recozimento simulado (Simulated Annealing - SA) e tem como objetivo a determinação do ponto de máximo global, buscando soluções fora de uma vizinhança próxima, de modo a evitar o atracamento em máximos locais da curva de potência de saída do arranjo de painéis fotovoltaicos, melhorando, assim, o aproveitamento da energia em situações de sombreamento parcial. A segunda parte do trabalho apresenta o projeto de controladores baseados no modelo interno (Internal Model Control – IMC) com 1 grau de liberdade (1 Degree of Freedom – 1 DOF) aplicados, primeiramente, ao conversor CC-CC Boost Quadrático, utilizado para o MPPT, e, posteriormente, a um inversor de tensão com filtro LCL, conectado à rede elétrica monofásica, operando no modo de injeção de corrente. É apresentada a modelagem matemática de ambos os conversores e analisada a compensação da realimentação interna ao sistema do inversor de tensão, correspondente ao desacoplamento da tensão da rede, através da estratégia de alimentação à frente (Feedforward). Visando-se uma base de comparação, para a análise de desempenho do conversor IMC – 1DOF, também é aplicado ao sistema de injeção de corrente, o controlador Proporcional-Ressonante (P+Res). São apresentados resultados de simulação computacional e experimentais de ambos os 8 controladores, os quais permitem verificar o desempenho do sistema em situação de rede fraca e carga local não-linear. / This paper presents the study, development and application of new control techniques for photovoltaic power generation systems, connected to single-phase power grid in order to improve the efficiency of these systems in relation to control methods typically used. The work is divided into two main parts, which are related to tracking the maximum power point (Maximum Power Point Tracking - MPPT) and then the internal controller of boost quadratic converters - side of the photovoltaic panels - as well as the controllers the voltage inverter, the side of the single-phase mains. The first part of the work is the development of a heuristic goal algorithm for MPPT, which is based on the method of simulated annealing (Simulated Annealing - SA) and aims at determining the overall maximum point, seeking out solutions in a close vicinity, so as to prevent the docking local maxima in the curve of power output of the photovoltaic array, thereby improving the utilization of energy in partial shading situations. The second part presents the design of controllers based on internal model (Internal Model Control - IMC) with 1 degree of freedom (1 Degree of Freedom - 1 DOF) applied, first, the DC-DC Boost Quadratic converter, used for MPPT, and thereafter, a voltage inverter with LCL filter connected to the single phase power supply operating in current injection mode. A mathematical modeling of both converters and analyzed the compensation of internal feedback to the voltage inverter system corresponding to the disconnection of the mains voltage through the power strategy a head (feedforward). A basis of comparison for the performance analysis of IMC-1DOF converter is aiming at, is also applied to the current injection system, Proportional-Resonant Controller (P + Res). They are presented computer simulation and experimental results of both controllers, which allow you to check the system performance in low and non-linear local load network situation. / Tese (Doutorado)

Foram desenvolvidos sistemas de medidas visando a caracterização de células solares de sílico monocristalino. Para isso, foram determinadas as características I x V no escuro para diferentes níveis de iluminação. Curvas de resposta espectral e capacitância em função da tensão inversa aplicada foram também obtidas. Foi feita uma avaliação do comportamento dessas células em função da temperatura e realizadas medidas de profundidade de junção utilizando-se três métodos distintos. Os principais parâmetros, que determinam o desempenho dessas células, foram obtidos boa concordância com a teoria e com os resultados apresentados na literatura. / Systems of measurements were developed for the characterization of single crystal silicon solar cells. For that, the curves I x V were measured in the dark and for different intensity of illumination. Curves of spectral response and of capacitance as a function of the reciprocal of the voltage were also measured. The behavior of the cells as a function of temperature was analysed and also measurements of junction depth were made by three different methods. Values for the parameters that characterize the cells were obtained, showing a good agreement with theoretical values and also with already reported values.

Submitted by Renata Lopes (renatasil82@gmail.com) on 2016-03-04T10:45:15Z No. of bitstreams: 1 leandrodamottaborges.pdf: 2242416 bytes, checksum: 10ac80b836250ec857dfe2dc8f819119 (MD5) / Approved for entry into archive by Adriana Oliveira (adriana.oliveira@ufjf.edu.br) on 2016-04-24T01:49:45Z (GMT) No. of bitstreams: 1 leandrodamottaborges.pdf: 2242416 bytes, checksum: 10ac80b836250ec857dfe2dc8f819119 (MD5) / Made available in DSpace on 2016-04-24T01:49:45Z (GMT). No. of bitstreams: 1 leandrodamottaborges.pdf: 2242416 bytes, checksum: 10ac80b836250ec857dfe2dc8f819119 (MD5) Previous issue date: 2013-09-27 / Este trabalho apresenta o estudo, dimensionamento e gestão de um sistema solar fotovoltaico isolado da rede elétrica para alimentar cargas de equipamentos de automação industrial. Um exemplo de aplicação são unidades de comando e sinalização ferroviária que, em alguns casos, são comandadas por relés e, mais atualmente, sendo substituídas por Controladores Lógico Programáveis. No sistema solar fotovoltaico isolado, o excedente de energia elétrica produzida nos painéis solares fotovoltaicos é armazenado em baterias eletroquímicas estacionárias de chumbo-ácido para posterior aproveitamento durante o período noturno e de baixa produção de eletricidade. Esse tipo de bateria apresenta efeito de memória, não pode sofrer descarga profunda ou ser submetida a tensões elevadas. Assim, este trabalho visa especificar e dimensionar um sistema solar fotovoltaico para aplicações em cargas de automação industrial isolados da rede elétrica, bem como assegurar elevada vida útil da bateria eletroquímica de chumbo-ácido sem prejudicar o rastreamento de máxima potência dos painéis solares fotovoltaicos. Para isso, uma estratégia de gestão de energia possibilita alterar o controle do conversor CC-CC que realiza a interconexão entre os painéis solares fotovoltaicos e a bateria eletroquímica. Resultados de simulação computacional apontam para o bom desempenho conceitual do sistema e seu potencial para a aplicação pretendida. / This work presents the study, design and management of a stand-alone photovoltaic system to feed industrial automation load. E examples of application are railway signaling unit controls, which in some cases are controlled by electromechanical relays and more currently being replaced by programmable logical controllers. In a stand-alone photovoltaic system, the excess of electricity produced in the photovoltaic panels is stored in lead-acid stationary electrochemical batteries for later use during the night and low electricity production periods. This kind of battery presents memory effect, cannot have deep discharge or be subjected to high voltages. Thus, this work aims to specify and size a solar photovoltaic system for applications in industrial automation loads isolated from the grid, as well as ensuring longer lifetime to electrochemical battery of lead-acid without harming the maximum power tracker of photovoltaic panels. For this, a strategy for changing power management enables the control of DC-DC converter that performs the interconnection of photovoltaic panels and electrochemical battery. Results of computer simulation indicate the good conceptual performance of the system and its potential for the intended application.

The aim of this thesis is to describe the advantages of simultaneous utilization of photovoltaic and wind electricity in an autonomous system, supplying the household with electricity without connection to the electrical grid. The most used methods of connecting photovoltaic modules and wind generators to chemical batteries are discussed. Several maximum power point tracking methods and their properties are described. A block schematic diagram of an autonomous off-grid system utilizing chemical accumulators is proposed. The system also contains an inverter producing standard mains voltage 230 VAC to supply common household appliances. A Quasi-Square Wave converter topology was chosen for all three power converters. An experimental 180 W output power QSW converter with one controllable switch was designed, simulated with Pspice, manufactured and tested to verify the efficiency of the topology. Excellent agreement was found between predicted and measured efficiency at full output power. Efficiency for reliable operation varies between 89% and 92,2% at full power and depends mainly power inductor and MOSFET used. After successful evaluation of QSW topology, the power converters for the main system were designed. Because of higher power, the converters were designed as four-phase, whereas each phase contains two controllable switches to boost efficiency mainly in low-power area. The most critical and difficult part of the project was to design the mixed-signal control sections for the converters to ensure proper switching of two controllable MOSFETs in each phase. For user interactivity, main control board with graphic LC display, Ethernet module and SD memory card slot was also manufactured.

<div>In this paper various applications of axial tensile load, bending load, and rolling loading has been applied to a Copper Indium Gallium Diselenide (CIGS) Solar Cell to lean how it would affect the solar cell parameters of: Open circuit voltage (Voc), Short circuit current, (Isc), Maximum power (Pmax), and Efficiency (EFF), and Fill Factor (FF). These Relationships were found for with three different experiments. The first experiment the applies axial tensile stress is to a CIGS solar cell ranging from 0 to 200 psi with various strain rates: 0.0001, 0.001, 0.01, and 0.1 in/sec as well as various relaxation time: 1min, 5min, and 10 min while the performance of solar cell is measured. The results of this gave several trends couple pertaining the Voc . The first is that open circuit voltage increases slightly with increasing stress. The second is the rate of increase (the slope) increases with longer relaxation times. The second set of trend pertains to the Isc. The first is that short circuit current generally is larger with larger stress. The second is there seems to be a general increase in the Isc up to a given threshold of stress. After that threshold the Isc seems to decrease. The threshold stress varies depending on strain rate and relaxation time. The second set of experiments consisted of holding a CIGS solar cell in a fixed curved position while it was in operational use. The radii of the curved cells were: 0.41, 0.20, 0.16, 0.13, 0.11, 0.094, and 0.082 m. The radii were performed for both concave and convex cell curvature. The trends for this show a slight decrease in all cell parameters with decreasing radii, the exception being Voc which is not effecting, the convex curvature causing a slightly faster decrease than the concave. This set of experiments were also processed to find the trends of the single diode model parameters of series resistance (Rs), shunt resistance (Rsh), dark current (I0), and saturation current (IL), which agreed with the experimental results. The second experiment consisted of rolling a CIGS solar cell in tensile (cells towards dowel.) and compression (cells away from dowel) around a dowel to create internal damage. The diameter of the dowels decreased. The dowel diameters were: 2. 1.75, 1.25, 1, 0.75, 0.5, and 0.25 inches. This experiment showed similar trends as the bending one but also had a critical diameter of 1.75 in where beyond that damage much greater. Finally a parametric study was done in COMSOL Multiphysics® to examine how changes in the CIGS material properties of electron mobility (EM), electron life time, (EL), hole mobility 15 (HM), and Hole life time (HL) effect the cell parameters. The trends are of an exponential manner that converges to a given value as the material properties increase. When EL, EM, HL are very small, on the order of 10-4 times smaller than their accepted values, a transient like responses occurs.<br></div>

A heavy duty vehicle looses approximately 30-40 % of the energy in the fuel as waste heat through the exhaust system. Recovering this waste heat would make the vehicle meet the legislative and market demands of emissions and fuel consumption easier. This recovery is possible by transforming the waste heat to electric power using a thermoelectric generator. However, the thermoelectric generator electric characteristics makes direct usage of it unprotable, thus an electric power conditioner is necessary. First a study of dierent DC-DC converters is presented, based on that the most suitable converter for thermoelectric application is determined. In order to maximize the harvested power, maximum power point tracking algorithms have been studied and analyzed. After the investigation, the single ended primary inductor converter was simulated and implemented with a perturb and observe algorithm, and the incremental conductance algorithm. The converter was tested with a 20 W thermoelectric generator, and evaluated.The results show that the incremental conductance is more robust and stable compared to the perturb and observe algorithm. Further on, the incremental conductance also has a higher average eciency during real implementation.

This thesis aims to increase photovoltaic (PV) panel power efficiency by employing a cooling system based on water circulation, which represents an improved version of water flow based active cooling systems. Theoretical calculations involved finding the heat produced by the PV panel and the circulation water flow required to remove this heat. A data logger and a cooling system for a test panel of 20W was designed and employed to study the relationship between the PV panel surface temperature and its output power. This logging and cooling system includes an Arduino microcontroller extended with a data logging shield, temperature sensing probes, current sensors, and a DC water pump. Real-time measurements were logged every minute for one or two day periods under various irradiance and air temperature conditions. For these experiments, a load resistance was chosen to operate the test panel at its maximum power point. Results indicate that the cooling system can yield an improvement of 10% in power production. Based on the observations from the test panel experiments, a cooling system was devised for a PV panel array of 640 W equipped with a commercial charge controller. The test data logger was repurposed for this larger system. An identical PV array was left uncooled and monitored simultaneously to compare the effect of cooling, demonstrating that the cooled array provided up to an extra 132W or 20% of maximum power for sunny weather conditions. Future expansion possibilities of the project include automated water level monitoring system and water filtration systems.

No description available.