This document explores the isolated multiple-input single ended primary inductor converter (IMISEPIC) and discusses its application. This thesis proposes the following control methods such as current feed-forward control, voltage feedback control and maximum power point control to analyze the IMISEPIC. Zero-ripple technique is also applied to IMISEPIC in order to increase the converter’s life-time. Design strategy and concerns about the IMISEPIC are also presented, and simulations and circuit experiments are conducted to verify the analysis. Finally, the discussion about control limitation is used for future design consideration. / text

A heavy duty vehicle looses approximately 30-40 % of the energy in the fuel as waste heat through the exhaust system. Recovering this waste heat would make the vehicle meet the legislative and market demands of emissions and fuel consumption easier. This recovery is possible by transforming the waste heat to electric power using a thermoelectric generator. However, the thermoelectric generator electric characteristics makes direct usage of it unprotable, thus an electric power conditioner is necessary. First a study of dierent DC-DC converters is presented, based on that the most suitable converter for thermoelectric application is determined. In order to maximize the harvested power, maximum power point tracking algorithms have been studied and analyzed. After the investigation, the single ended primary inductor converter was simulated and implemented with a perturb and observe algorithm, and the incremental conductance algorithm. The converter was tested with a 20 W thermoelectric generator, and evaluated.The results show that the incremental conductance is more robust and stable compared to the perturb and observe algorithm. Further on, the incremental conductance also has a higher average eciency during real implementation.

The use of SMPS (Switched mode power supply) in embedded systems is continuously increasing. The technological requirements of these systems include simultaneously a very good voltage regulation and a strong compactness of components. SEPIC ( Single-Ended Primary Inductor Converter) is a DC/DC switching converter which possesses several advantages with regard to the other classical converters. Due to the difficulty in control of its 4th-order and non linear property, it is still not well-exploited. The objective of this work is the development of successful strategies of control for a SEPIC converter on one hand and on the other hand the effective implementation of the control algorithm developed for embedded applications (FPGA, ASIC) where the constraints of Silicon surface and the loss reduction factor are important. To do it, two non linear controls and two observers of states and load have been studied: a control and an observer based on the principle of sliding mode, a deadbeat predictive control and an Extended Kalman observer. The implementation of both control laws and the Extended Kalman observer are implemented in FPGA. An 11-bit digital PWM has been developed by combining a 4-bit Δ-Σ modulation, a 4-bit segmented DCM (Digital Clock Management) phase-shift and a 3-bit counter-comparator. All the proposed approaches are experimentally validated and constitute a good base for the integration of embedded switching mode converters

L’utilisation des alimentations à découpage (SMPSs : switched mode power supplies) est à présent largement répandue dans des systèmes embarqués en raison de leur rendement. Les exigences technologiques de ces systèmes nécessitent simultanément une très bonne régulation de tension et une forte compacité des composants. SEPIC (Single-Ended Primary Inductor Converter) est un convertisseur à découpage DC/DC qui possède plusieurs avantages par rapport à d’autres convertisseurs de structure classique. Du fait de son ordre élevé et de sa forte non linéarité, il reste encore peu exploité. L’objectif de ce travail est d’une part le développement des stratégies de commande performantes pour un convertisseur SEPIC et d’autre part l’implémentation efficace des algorithmes de commande développés pour des applications embarquées (FPGA, ASIC) où les contraintes de surface silicium et le facteur de réduction des pertes sont importantes. Pour ce faire, deux commandes non linéaires et deux observateurs augmentés (observateurs d’état et de charge) sont exploités : une commande et un observateur fondés sur le principe de mode de glissement, une commande prédictive et un observateur de Kalman étendu. L’implémentation des deux lois de commande et l’observateur de Kalman étendu sont implémentés sur FPGA. Une modulation de largeur d’impulsion (MLI) numérique à 11-bit de résolution a été développée en associant une technique de modulation Δ-Σ de 4-bit, un DCM (Digital Clock Management) segmenté et déphasé de 4-bit, et un compteur-comparateur de 3-bit. L’ensemble des approches proposées sont validées expérimentalement et constitue une bonne base pour l’intégration des convertisseurs à découpage dans les alimentations embarquées. / The use of SMPS (Switched mode power supply) in embedded systems is continuously increasing. The technological requirements of these systems include simultaneously a very good voltage regulation and a strong compactness of components. SEPIC ( Single-Ended Primary Inductor Converter) is a DC/DC switching converter which possesses several advantages with regard to the other classical converters. Due to the difficulty in control of its 4th-order and non linear property, it is still not well-exploited. The objective of this work is the development of successful strategies of control for a SEPIC converter on one hand and on the other hand the effective implementation of the control algorithm developed for embedded applications (FPGA, ASIC) where the constraints of Silicon surface and the loss reduction factor are important. To do it, two non linear controls and two observers of states and load have been studied: a control and an observer based on the principle of sliding mode, a deadbeat predictive control and an Extended Kalman observer. The implementation of both control laws and the Extended Kalman observer are implemented in FPGA. An 11-bit digital PWM has been developed by combining a 4-bit Δ-Σ modulation, a 4-bit segmented DCM (Digital Clock Management) phase-shift and a 3-bit counter-comparator. All the proposed approaches are experimentally validated and constitute a good base for the integration of embedded switching mode converters