Heterogeneous electrocatalysis is the usage of solid materials to decrease the amount of energy needed to produce chemicals using electricity. It is of core importance for modern life, as it enables production of chemicals, such as chlorine gas and sodium chlorate, needed for e.g. materials and pharmaceuticals production. Furthermore, as the need to make a transition to usage of renewable energy sources is growing, the importance for electrocatalysis used for electrolytic production of clean fuels, such as hydrogen, is rising. In this thesis, work aimed at understanding and improving electrocatalysts used for these purposes is presented. A main part of the work has been focused on the selectivity between chlorine gas, or sodium chlorate formation, and parasitic oxygen evolution. An activation of anode surface Ti cations by nearby Ru cations is suggested as a reason for the high chlorine selectivity of the “dimensionally stable anode” (DSA), the standard anode used in industrial chlorine and sodium chlorate production. Furthermore, theoretical methods have been used to screen for dopants that can be used to improve the activity and selectivity of DSA, and several promising candidates have been found. Moreover, the connection between the rate of chlorate formation and the rate of parasitic oxygen evolution, as well as the possible catalytic effects of electrolyte contaminants on parasitic oxygen evolution in the chlorate process, have been studied experimentally. Additionally, the properties of a Co-doped DSA have been studied, and it is found that the doping makes the electrode more active for hydrogen evolution. Finally, the hydrogen evolution reaction on both RuO2 and the noble-metal-free electrocatalyst material MoS2 has been studied using a combination of experimental and theoretically calculated X-ray photoelectron chemical shifts. In this way, insight into structural changes accompanying hydrogen evolution on these materials is obtained. / Heterogen elektrokatalys innebär användningen av fasta material för att minska energimängden som krävs för produktion av kemikalier med hjälp av elektricitet. Heterogen elektrokatalys har en central roll i det moderna samhället, eftersom det möjliggör produktionen av kemikalier såsom klorgas och natriumklorat, som i sin tur används för produktion av t ex konstruktionsmaterial och läkemedel. Vikten av användning av elektrokatalys för produktion av förnybara bränslen, såsom vätgas, växer dessutom i takt med att en övergång till användning av förnybar energi blir allt nödvändigare. I denna avhandling presenteras arbete som utförts för att förstå och förbättra sådana elektrokatalysatorer. En stor del av arbetet har varit fokuserat på selektiviteten mellan klorgas och biprodukten syrgas i klor-alkali och kloratprocesserna. Inom ramen för detta arbete har teoretisk modellering av det dominerande anodmaterialet i dessa industriella processer, den så kallade “dimensionsstabila anoden” (DSA), använts för att föreslå en fundamental anledning till att detta material är speciellt klorselektivt. Vi föreslår att klorselektiviteten kan förklaras av en laddningsöverföring från ruteniumkatjoner i materialet till titankatjonerna i anodytan, vilket aktiverar titankatjonerna. Baserat på en bred studie av ett stort antal andra dopämnen föreslår vi dessutom vilka dopämnen som är bäst lämpade för produktion av aktiva och klorselektiva anoder. Med hjälp av experimentella studier föreslår vi dessutom en koppling mellan kloratbildning och oönskad syrgasbildning i kloratprocessen, och vidare har en bred studie av tänkbara elektrolytföroreningar utförts för att öka förståelsen för syrgasbildningen i denna process. Två studier relaterade till elektrokemisk vätgasproduktion har också gjorts. En experimentell studie av Co-dopad DSA har utförts, och detta elektrodmaterial visade sig vara mer aktivt för vätgasutveckling än en standard-DSA. Vidare har en kombination av experimentell och teoretisk röntgenfotoelektronspektroskopi använts för att öka förståelsen för strukturella förändringar som sker i RuO2 och i det ädelmetallfria elektrodmaterialet MoS2 under vätgasutveckling. / <p>QC 20151119</p>

The experimental data and results demonstrated here illustrate the preparation and application of mesoporous metal oxides in energy storage, adsorption, and catalysis. First, a new method of controlling the pore size and wall thickness of mesoporous silica was developed by controlling the calcination temperature. A series of such silica were used as hard templates to prepare the mesoporous metal oxide Co₃O₄. Using other methods, such as varying the silica template hydrothermal treatment temperature, using colloid silica, varying the materials ratio etc., a series of mesoporous β-MnO₂ with different pore size and wall thickness were prepared. By using these materials it has been possible to explore the influence of pore size and wall thickness on the rate of lithium intercalation into mesoporous electrode. There is intense interest in lithium intercalation into titanates due to their potential advantages (safety, rate) replacing graphite for new generation Li-ion battery. After the preparation of an ordered 3D mesoporous anatase the lithium intercalation as anode material has been investigated. To the best of our knowledge, there are no reports of ordered crystalline mesoporous metal oxides with microporous walls. Here, for the first time, the preparation and characterization of three dimensional ordered crystalline mesoporous α-MnO₂ with microporous wall was described, in which K+ and KIT-6 mesoporous silica act to template the micropores and mesopores, respectively. It was used as a cathode material for Li-ion battery. Its adsorption behavior and magnetic property was also surveyed. Following this we described the preparation and characterization of mesoporous CuO and reduced Cu[subscript(x)]O, and demonstrated their application in NO adsorption and delivery. Finally a series of crystalline mesoporous metal oxides were prepared and evaluated as catalysts for the CO oxidation.

Biomass is one of the most promising replacements for fossil fuels as a feedstock for chemical and transportation fuel production. The combination of low vapor pressure and high polarity of most biomass derived molecules makes water the ideal solvent for biomass upgrading reaction schemes. Metal oxide and metal oxide supported catalysts are heavily used in oil refining and petrochemical production, and are capable of upgrading biomass molecules as well. However, the surface chemistries that dictate the behavior of aqueous phase biomass upgrading reactions over metal oxide catalysts are not nearly as well understood as in the case of gas phase hydrocarbon refining systems. This dissertation aims to investigate the surface chemistries of biomass derived oxygenate molecules on metal oxide and metal oxide supported metal catalysts. There are three main objectives in this dissertation: to understand how two and three carbon polyols interact with metal oxide surfaces, to elucidate the role of various surface sites on polyol-metal oxide interactions, and to discover the surface species of kinetic importance in aqueous phase reforming reactions of biomass molecules. Transmission infrared spectroscopy and density functional theory modeling were the major techniques used to demonstrate that polyols with alcohol groups on the first and third carbons, 1,3-propanediol and glycerol, form a multidentate surface species with a bridging alkoxide bond and an acid/base interaction through their two primary alcohol groups with Lewis acid sites of g-Al₂O₃. These interactions occur in the presence of bulk water. Polyols with alcohol groups only on the first and second carbons, ethylene glycol and 1,2-propanediol, only formed alkoxy bonds with the g-Al₂O₃ surface when bulk water was not coadsorbed, and these bonds were removed by re-adsorbing water. Glycerol also forms the same surface species on other metal oxides with strong Lewis acidic character: TiO₂ anatase, ZrO₂, and CeO₂. Glycerol only forms hydrogen bonds with MgO, which lacks strongly Lewis acidic sites. Basic surface hydroxyls and surface oxygen atoms of the metal oxides only played a minor role in interacting with the adsorbed glycerol. In-situ attenuated total reflectance infrared spectroscopy demonstrated that the aqueous phase reforming of glycerol over a 5 wt% Pt on g-Al₂O₃ catalyst is hindered by residual platinum bound hydrogen or oxygen atoms from commonly utilized catalyst reduction or cleaning procedures, respectively. A pretreatment consisting of multiple iterations of dissolved oxygen, dissolved hydrogen, and dissolved helium in water flow periods provides the cleanest Pt surface for monitoring carbon monoxide formation dynamics, and allows for observing the rate limiting step of the aqueous phase reforming reactions water-gas shift removal of Pt bound carbon monoxide. The bridging bound carbon monoxide is preferentially removed over the linearly bound species via water gas shift reactions even at room temperature.

Solution processed circuits are expected to be the main components to achieve low cost, large area, flexible electronics. However, the commercialization of solution processed flexible electronics face several challenges. The passive component such as capacitors are limited in frequency range and operating voltage. The active component such as transistors suffer from low mobility ultimately leading to limited current-carrying capacity. Just as in traditional silicon technology, the fabrication process and material choices significantly impact the performance of the fabricated devices. My thesis focuses on the optimization of the performance of printed capacitors and transistors through investigation of several aspects of the device structure and fabrication process. The first part of this work focuses on the optimization of printed nanoparticle/polymer composite capacitors. Thin film metal oxide nanoparticle/polymer composites have enormous potential to achieve printable high-k dielectrics. The combination of high-k ceramic nanoparticle and polymer enables room temperature deposition of high dielectric constant film without the need of high temperature sintering process. The polymer matrix host fills the packing voids left behind by the nanoparticles resulting to higher effective dielectric permittivity as a system and suppresses surface states leading to reduced dielectric loss. Such composite systems have been employed in a number of flexible electronic applications such as the dielectrics in capacitors and thin film transistors. One of the most important properties of thin film capacitors is the breakdown field. In a typical capacitor system, the breakdown process leads to catastrophic failure that destroys the capacitor; however, in a nanoparticle/polymer composite system with self-healing property, the point of breakdown is not well-defined. The breakdown of the dielectric or electrodes in the system limits the leakage observed. It is possible, however, to define a voltage/field tolerance. Field tolerance is defined as the highest practical field at which the device stays operational with low failure rate by qualifying the devices with defined leakage current density. In my work, the optimization of the field tolerance of (Ba,Sr)TiO₃ (BST)/parylene-C composite capacitors is achieved by studying the influence of the electromigration parameter on leakage and field strength through the inherit asymmetrical structure of the fabricated capacitors. One approach to creating these composites is to use a spin-coated nanoparticle film together with vapor deposited polymers, which can yield high performance, but also forms a structurally asymmetric device. The performance of a nanoparticle BST/parylene-C composite capacitor is compared to that of a nanoparticle BST capacitor without the polymer layer under both directions of bias. The composite device shows a five orders of magnitude improvement in the leakage current under positive bias of the bottom electrode relative to the pure-particle device, and four orders of magnitude improvement when the top electrode is positively biased. The voltage tolerance of the device is also improved, and it is asymmetric (44 V vs. 28 V in bottom and top positive bias, respectively). This study demonstrates the advantage of this class of composite device construction, but also shows that proper application of the device bias in this type of asymmetrical system can yield an additional benefit. The dependence of the field tolerance of nanoparticle/polymer composite capacitors on the electromigration parameter of the electrodes is investigated using the symmetrical dielectric system. The breakdown is suppressed by selecting the polarity used in nanoparticle (Ba,Sr)TiO₃/parylene-C composite film-based capacitors. Metals including gold, silver, copper, chromium, and aluminum with comparable surface conditions were examined as the electrodes. The asymmetric silver, aluminum, gold, copper, and chromium electrode devices show a 64 %, 29 %, 28 %, 17 %, 33 %, improvement in the effective maximum operating field, respectively, when comparing bias polarity. The field at which filament formation is observed shows a clear dependence on the electromigration properties of the electrode material and demonstrates that use of electromigration resistant metal electrodes offers an additional route to improving the performance of capacitors using this nanoparticle/polymer composite architecture. The second part of my thesis focuses on the novel pneumatic printing process that enables manipulation of the crystal growth of the organic semiconductors to achieve oriented crystal with high mobility. Small molecule organic semiconductors are attracting immense attention as the active material for the large-area flexible electronics due to their solution processability, mechanical flexibility, and potential for high performance. However, the ability to rapidly pattern and deposit multiple materials and control the thin-film morphology are significant challenges facing industrial scale production. A novel and simple pneumatic nozzle printing approach is developed to control the crystallization of organic thin-films and deposit multiple materials with wide range of viscosity including on the same substrate. Pneumatic printing uses capillary action between the nozzle and substrate combined with control of air pressure to dispense the solution from a dispense tip with a reservoir. Orientation and size of the crystals is controlled by tuning the printing direction, speed, and the temperature of the substrate. The main advantages of pneumatic printing technique are 1) simple setup and process, 2) multi-material layered deposition applicable to wide range of solution viscosity, 3) control over crystal growth. The manipulation of crystal growth will be discussed in the next chapter. This method for performance optimization and patterning has great potential for advancing printed electronics. The dependence of the mobility of printed thin film 6,13-bis(triisopropylsilylethynyl) pentacene [TIPS-pentacene] and C8-BTBT on printing conditions is investigated, and the result indicates that the formation of well-ordered crystals occurs at an optimal head translation speed. A maximum mobility of 0.75 cm²/(Vs) is achieved with 0.3 mm/s printing speed and 1.3 cm²/(Vs) with 0.3 mm/s printing speed at 50C for TIPS-pentacene and C8-BTBT respectively. In summary, pneumatic printing technique can be an attractive route to industrial scale large area flexible electronics fabrication.

Metal oxide-facilitated transformation is likely an important degradation pathway of antibacterial agents at soil-water interfaces. Phenolic disinfectants (triclosan and chlorophene), fluoroquinolones (FQs), and aromatic N-oxides are of particular concern due to their widespread usage, potential toxicity and frequent detection in the environment. Results of the present study show that the above antibacterial agents are highly susceptible to metal oxide-facilitated oxidation. The interfacial reactions exhibit complex reaction kinetics, which are affected by solution pH, the presence of co-solutes, surface properties of metal oxides, and structural characteristics of antibacterial agents. Adsorption of the antibacterial agents to Mn and Fe oxide surfaces generally proceeds faster than oxidation reactions of these compounds by Mn and Fe oxides, especially in the case of Fe oxides. Reaction intermediates and end products are identified by GC/MS, LC/MS and/or FTIR. Structurally-related model compounds are examined to facilitate reaction site and mechanism elucidation. On the basis of experimental results and literature, reaction schemes are proposed. In general, the antibacterial agent is adsorbed to the oxide surface, forming a precursor complex. Electrons are transferred within the precursor complex from the antibacterial agent to the oxide, followed by releasing of the radical intermediates which undergo further reactions to generate oxidation products. The precursor complex formation and electron transfer are likely rate-limiting. For triclosan, phenoxy radicals are critical intermediates to form oxidation products through three pathways (i.e., radical coupling, further oxidation of the radical, and breakdown of an ether bond within the radical). The first two pathways are also operative in the oxidation of chlorophene. For FQs, oxidation generates radical intermediates that are most likely centered on the inner N in the piperazine ring. The radical intermediates then undergo three major pathways (i.e., radical coupling, N-dealkylation, and hydroxylation) to yield a variety of products. For aromatic N-oxides, a N-oxide radical intermediate is generated upon oxidation by MnO2, followed by the loss of oxygen from the N-oxide moiety and the formation of a hydroxyl group at the C-atom adjacent to the N-oxide moiety. Overall, a fundamental understanding of the reaction mechanisms between three classes of antibacterial agents and metal oxides has been obtained.

The metallic alloys employed in oxidizing environment at high temperature rely on the development of a protective oxide scale to sustain the long-term aggressive exposition. However, the oxide scale growth is most of the time coupled with stress and morphological developments limiting its lifetime and then jeopardizing the metallic component reliability. In this study, a mechanism of local stress effect on the oxidation kinetics at the metal/oxide interface is investigated. The objective is to improve the understanding on the possible interactions between stress generation and non-uniform oxide scale growth, which might result in a precipitated mechanical failure of the system. Two different oxides are studied, alumina and chromia, in two different industrial systems, thermal barrier coatings and solid oxide fuel cell interconnects. A specific thermodynamic treatment of local oxide phase growth coupled with stress generation is developed. The formulation is completed with a phenomenological macroscopic framework and a numerical simulation tool is developed allowing for realistic analyses. Two practical situations are simulated and analyzed, concerning an SOFC interconnect and a thermal barrier coating system, for which oxide scale growth and associated stress and morphological developments are critical. The consequence of the non-uniform oxide growth on the system resistance to mechanical failure is investigated. Finally, the influences of material-related properties are studied, providing optimization directions for the design of metallic alloys which would improve the mechanical lifetime of the considered systems.

Amorphous oxide semiconductors (AOSs) are of great current interest for thin-film transistor (TFT) channel layer applications. In particular, indium gallium zinc oxide (IGZO) is under intense development for commercial applications because of its demonstrated high performance at low processing temperatures. The objective of the research presented in this thesis is to provide detailed assessments of device stability, temperature dependence, and related phenomena for IGZO-based TFTs processed at temperatures between 200 °C and 300 °C. TFTs tested exhibit an almost rigid shift in log₁₀(I[subscript D]) – V[subscript GS] transfer curves in which the turn-on voltage, V[subscript ON], moves to a more positive gate voltage with increasing stress time during constant-voltage bias-stress testing of IGZO TFTs. TFT stability is improved as the post-deposition annealing temperature increases over the temperature range of 200 – 300 ºC. The turn-on voltage shift induced by constant-voltage bias-stressing is at least partially reversible; V[subscript ON] tends to recover towards its initial value of V[subscript ON] if the TFT is left unbiased in the dark for a prolonged period of time and better recovery is observed for a longer recovery period. V[subscript ON] for a TFT can be set equal to zero after bias-stress testing if the TFT electrodes are grounded and the TFT is maintained in the dark for a prolonged period of time. Attempts to accelerate the recovery process by application of a negative gate bias at elevated temperature (i.e., 100 ºC) were unsuccessful, resulting in severely degraded subthreshold swing. An almost rigid log₁₀(I[subscript D]) – V[subscript GS] transfer curve shift to a lower (more negative) V[subscript ON] with increasing temperature is observed in the range of –50 °C to +50 °C, except for a TFT with an initial V[subscript ON] equal to zero, in which case the log₁₀(ID) – V[subscript GS] transfer curve is temperature-independent. A more detailed temperature-dependence assessment, however, indicates that the log₁₀(I[subscript D]) – V[subscript GS] transfer curve shift is not exactly rigid since the mobility is found to increase slightly with increasing temperature. A noticeable anomaly is observed in certain log₁₀(I[subscript D]) – VGS transfer curves, especially when obtained at elevated temperature (e.g., 30 and 50 ºC), in which I[subscript D] decreases precipitously near zero volts in the positive gate voltage sweep. This anomaly is attributed to a gate-voltage-step-involved detrapping and subsequent retrapping of electrons in the accumulation channel and/or channel/gate insulator interface. In fact, all IGZO TFT stability and temperature-dependence trends are attributed to channel interface and/or channel bulk trapping/detrapping. / Graduation date: 2009

Orientador: Margarita Ballester F. Santos / Tese (doutorado) - Universidade Estadual de Campinas, Faculdade de Engenharia Mecanica / Made available in DSpace on 2018-07-22T11:08:57Z (GMT). No. of bitstreams: 1 Kawakami_Kenji_D.pdf: 19175620 bytes, checksum: b6a661ea70e2abc1018ffcac8a295caa (MD5) Previous issue date: 1996 / Resumo: Não informado / Abstract: In this work is developped a procedure for evaluation of oxides films properties. Through Electrochemical Impedance Spectroscopy, by obtaining from Bode diagrams a capacitance and dissipation coefficient. It is proposed a mathematical model for the metal-oxide-eletrolute system description based on na equivalent circuit. The oxide films properties are evaluated by fitting procedure. The technique . is applied to Ti-6AI-7Nb anodized alloys, used as a substitute for Ti-6AI-4Valloy, in surgical aplications. The results show the possibility of film properties evaluation from direct analysis of Bode diagrams / Doutorado / Materiais e Processos de Fabricação / Doutor em Engenharia Mecânica

Metal oxide reactions at metal oxide surfaces or at metal-metal oxide interfaces are of exceptional significance in areas such as catalysis, micro- and nanoelectronics, chemical sensors, and catalysis. Such reactions are frequently complicated by the presence of high electric fields and/or H2O-containing environments. The focus of this research was to understand (1) the iron oxide growth mechanism on Fe(111) at 300 K and 500 K together with the effect of high electric fields on these iron oxide films, and (2) the growth of alumina films on two faces of Ni3Al single crystal and the interaction of the resulting films with water vapor under non-UHV conditions. These studies were conducted with AES, LEED, and STM. XPS was also employed in the second study. Oxidation of Fe(111) at 300 K resulted in the formation of Fe2O3 and Fe3O4. The substrate is uniformly covered with an oxide film with relatively small oxide islands, i.e. 5-15 nm in width. At 500 K, Fe3O4 is the predominant oxide phase formed, and the growth of oxide is not uniform, but occurs as large islands (100 - 300 nm in width) interspersed with patches of uncovered substrate. Under the stress of STM induced high electric fields, dielectric breakdown of the iron oxide films formed at 300 K occurs at a critical bias voltage of 3.8 ± 0.5 V at varying field strengths. No reproducible result was obtained from the high field stress studies of the iron oxide formed at 500 K. Ni3Al(110) and Ni3Al(111) were oxidized at 900 K and 300 K, respectively. Annealing at 1100 K was required to order the alumina films in both cases. The results demonstrate that the structure of the 7 Å alumina films on Ni3Al(110) is k-like, which is in good agreement with the DFT calculations. Al2O3/Ni3Al(111) (γ'-phase) and Al2O3/Ni3Al(110) (κ-phase) films undergo drastic reorganization and reconstruction, and the eventual loss of all long-range order upon exposure to H2O pressure > 10-5 Torr. Al2O3/Ni3Al(110) film is significantly more sensitive to H2O vapor than the Al2O3/Ni3Al(111) film, and this may be due to the incommensurate nature of the oxide/Ni3Al(110) interface. STM measurements indicate that this effect is pressure- rather than exposure- dependent, and that the oxide instability is initiated at the oxide surface, rather than at the oxide/metal interface. The effect is not associated with formation of a surface hydroxide, yet is specific to H2O (similar O2 exposures have no effect).

Land application of biosolids has become common practice in the United States as an alternative to industrial fertilizers. Although nutrient rich, biosolids have been found to contain high concentrations of emerging contaminants (e.g. pharmaceuticals, personal care products) while containing a significant fraction of inorganic nano-scale colloidal materials such as oxides of iron, titanium, and aluminum. Given their reactivity and small size, there are many questions concerning the potential migration of these nano-sized colloidal materials through the soil column and into our surface and groundwater bodies. Transport of emerging pollutants of concern through the soil column, at minimum, is impacted by colloidal properties (e.g. chemical composition, shape, aggregation kinetics), solution chemistry (e.g. pH, ionic strength, natural organic matter), and water flow velocity. The purpose of this current research was to characterize the long-term transport behavior of aluminum oxide nanoparticles (Al2O3) through a natural porous media with changes in pH, aqueous-phase concentration, pore-water velocity and electrolyte valence. Additionally, deposition rates during the initial stages of deposition were compared to several models developed based on colloid filtration theory and DLVO stability theory. Benchtop column laboratory experiments showed that, under environmentally relevant groundwater conditions, Al2O3 nanoparticles are mobile through saturated porous media. Mobility increased under conditions in which the nanoparticles and porous media were of like charge (pH 9). Changes in linear pore water velocity, under these same high pH conditions, showed similar transport behavior with little mass retained in the system. Deposition is believed to be kinetically controlled at pH 9, as evidenced by the slightly earlier breakthrough as flow rate increased and was further supported by observed concentration effects on the arrival wave following several stop flows. While lower aqueous-phase concentrations resulted in significantly longer breakthrough times, the total mass retained in the system was found to be independent of concentration. Additionally, experimental deposition rate coefficients (kd), used to describe deposition kinetics under "clean bed" conditions, were similar across the aqueous-phase concentrations studied. The use of calcium chloride electrolyte solution in transport studies resulted in enhanced mobility relative to potassium chloride suggesting that changes in groundwater solution chemistry could impact mobility of contaminants associated with biosolids. Predicted deposition rate coefficients, using three different models, were found to under- or over-predict values relative to those experimentally determined values depending on the model. This current research has shown that nanocolloids associated with biosolids, specifically Al2O3, are mobile through saturated porous media. Given the ubiquity of nanocolloidal materials, particularly engineered nanomaterials, coupled with the expected increase in land-application of biosolids, a clear understanding of their transport and fate is prudent to understanding the potential impact these emerging pollutants may have on our surface and groundwater bodies.