none

This study used electrospinning to fabricate a polyvinylidene fluoride (PVDF) piezoelectric nanofiber harvesting device with interdigitated electrode to capture ambient energy. According to d33 mechanical-electric energy conversion mode, the energy harvesting device can be applied on the low frequency ambient vibration and impact abilities for the transformation mechanical energy into electrical energy effectively. First, the PVDF powder was mixed in acetone solution uniformly and the dimethyl sulfoxide (DMSO) was mixed with multi-walled carbon nanotube (MWCNT) to prepare PVDF macromolecular solution. The mixed solution was filled in a metals needle injector and contacted hundreds of voltage. After the PVDF drop in the needle was subjected to high electric field, the drop overcame surface tension of the solution itself, then extremely fine PVDF fiber was formed and spun out. The electrospun was collected orderly using X-Y digital control stage and the linear diameter of electrospun can be controlled easily by adjusting the travelling speed of the stage. In the spinning process, as affected by stretching strain and electric field at the same time, the PVDF piezoelectric fiber resulted in electric polarization and transformed £] piezoelectric crystal phase, in which the dipoles are oriented in the same direction. Furthermore, MWCNT was added to improve the mechanical properties of fiber and increase £] phase, to enhance the tensile strength and piezoelectric property of PVDF fiber effectively. Finally, the photolithography was used to fabricate interdigitated electrodes with 100£gm gap on the flexible PI substrate. The PVDF fibers, with a length and diameter of approximately 1cm and 700-1000nm, were aligned on interdigitated electrodes and packaged with the PI film. In order to increase the conversion efficiency of piezoelectric fiber in d33 mode, the PVDF fibers were repolarized in a high electric field. The results showed that the PVDF fiber energy harvesting device can generate 15mV open-circuit voltage under low frequency vibration of 4Hz and generate above 30mV open-circuit voltage under 6Hz vibrations. As compared with the piezoelectric fiber not repolarized by interdigitated electrode, its output voltage was increased by1- 2 times.

Through past research, it is known that carbon nanotubes have the potential of enhancing the thermal performance of heat transfer fluids. The research is of importance in electronics cooling, defense, space, transportation applications and any other area where small and highly efficient heat transfer systems are needed. However, most of the past work discusses the experimental results by focusing on the effect of varying concentration of carbon nanotubes (CNTs) on the thermal performance of CNT nanofluids. Not much work has been done on studying the effect of processing variables. In the current experimental work, accurate measurements were carried out in an effort to understand the impact of several key variables on laminar flow convective heat transfer. The impact of ultrasonication energy on CNT nanofluids processing, and the corresponding effects on flow and thermal properties were studied in detail. The properties measured were viscosity, thermal conductivity and the convective heat transfer under laminar conditions. Four samples of 1 wt % multi walled carbon nanotubes (MWCNT) aqueous suspensions with different ultrasonication times were prepared for the study. Direct imaging was done using a newly developed wet-TEM technique to assess the dispersion characteristics of CNT nanofluid samples. The results obtained were discussed in the context of the CNT nanofluid preparation by ultrasonication and its indirect effect on each of the properties. It was found that the changes in viscosity and enhancements in thermal conductivity and convective heat transfer are affected by ultrasonication time. The maximum enhancements in thermal conductivity and convective heat transfer were found to be 20 % and 32 %, respectively, in the sample processed for 40 minutes. The thermal conductivity enhancement increased considerably at temperatures greater than 24 °C. The percentage enhancement in convective heat transfer was found to increase with the axial distance in the heat transfer section. Additionally, the suspensions were found to exhibit a shear thinning behavior, which followed the Power Law viscosity model.

No description available.

This study presents near-field electrospinning (NFES) on flat and hollow cylindrical process to fabricate permanent piezoelectricity of polyvinylidene fluoride (PVDF)/ multi-walled carbon nanotube (MWCNT) piezoelectric nanofibers. Then the mechanical properties of fibers were measured. PVDF is a potential piezoelectric polymer material combining desirable mechanical, thermal, electrical properties with excellent chemical resistance. The existing researches mostly focused on piezoelectric thin film process. However, the research of characteristic about piezoelectric fiber is little. The methods of measurement of the mechanical properties (Young¡¦s modulus, hardness, and tensile strength¡Belongation) of the electrospun PVDF/MWCN composite nanofiber were carried out by using nano-indention test (MTS Nanoindenter Windows XP System) and tensile test (Microforce Testing System). By setting electric field (1¡Ñ107 V/m), rotating velocity (900 rpm) of the hollow cylindrical glass tube on a motion X-Y stage (2 mm/sec) and PVDF solution concentration (16 wt%), and MWCNT (0.03 wt%), in-situ electric poling, mechanical stretching and morphology of PVDF nanofiber were demonstrated. After the experiments of nano-indention test and tensile strength test, it is suggested that the good mechanical properties in NFES on cylindrical process. The results show that the mechanical properties of composite nanofiber are better than the conventional NFES process. The Young¡¦s modulus of 16% PVDF fiber prepared by cylindrical process is 0.89 GPa and hardness is 26.5 MPa. The mechanical properties were increased 56.2% and 49.4% after adding 0.03% of MWCNT, corresponding to 1.39 GPa and 39.6 MPa. The tensile strength was increased 32.7% and elongation at breaking point was increased 35% after adding 0.03% MWCNT.

Radio frequency identification (RFID) and sensing are two key technologies enabling the Internet of Things (IoT). Development of RFID tags augmented with sensing capabilities (RFID sensor tags) would allow a variety of new applications, leading to a new paradigm of the IoT. Chipless RFID sensor technology offers a low-cost solution by eliminating the need of an integrated circuit (IC) chip, and is hence highly desired for many applications. On the other hand, printing technologies have revolutionized the world of electronics, enabling cost-effective manufacturing of large-area and flexible electronics. By means of printing technologies, chipless RFID sensor tags could be made flexible and lightweight at a very low cost, lending themselves to the realization of ubiquitous intelligence in the IoT era. This thesis investigated three construction methods of printable chipless RFID humidity sensor tags, with focus on the incorporation of the sensing function. In the first method, wireless sensing based on backscatter modulation was separately realized by loading an antenna with a humidity-sensing resistor. An RFID sensor tag could then be constructed by combining the wireless sensor with a chipless RFID tag. In the second method, a chipless RFID sensor tag was built up by introducing a delay line between the antenna and the resistor. Based on time-domain reflectometry (TDR), the tag encoded ID in the delay time between its structural-mode and antenna-mode scattering pulse, and performed the sensing function by modulating the amplitude of the antenna-mode pulse. In both of the above methods, a resistive-type humidity-sensing material was required. Multi-walled carbon nanotubes (MWCNTs) presented themselves as promising candidate due to their outstanding electrical, structural and mechanical properties. MWCNTs functionalized (f-MWCNTs) by acid treatment demonstrated high sensitivity and fast response to relative humidity (RH), owing to the presence of carboxylic acid groups. The f-MWCNTs also exhibited superior mechanical flexibility, as their resistance and sensitivity remained almost stable under either tensile or compressive stress. Moreover, an inkjet printing process was developed for the f-MWCNTs starting from ink formulation to device fabrication. By applying the f-MWCNTs, a flexible humidity sensor based on backscatter modulation was thereby presented. The operating frequency range of the sensor was significantly enhanced by adjusting the parasitic capacitance in the f-MWCNTs resistor. A fully-printed time-coded chipless RFID humidity sensor tag was also demonstrated. In addition, a multi-parameter sensor based on TDR was proposed.The sensor concept was verified by theoretical analysis and circuit simulation. In the third method, frequency-spectrum signature was utilized considering its advantages such as coding capacity, miniaturization, and immunity to noise. As signal collision problem is inherently challenging in chipless RFID sensor systems, short-range identification and sensing applications are believed to embody the core values of the chipless RFID sensor technology. Therefore a chipless RFID humidity sensor tag based on near-field inductive coupling was proposed. The tag was composed of two planar inductor-capacitor (LC) resonators, one for identification, and the other one for sensing. Moreover, paper was proposed to serve as humidity-sensing substrate for the sensor resonator on accounts of its porous and absorptive features. Both inkjet paper and ordinary packaging paper were studied. A commercial UV-coated packaging paper was proven to be a viable and more robust alternative to expensive inkjet paper as substrate for inkjet-printed metal conductors. The LC resonators printed on paper substrates showed excellent sensitivity and reasonable response time to humidity in terms of resonant frequency. Particularly, the resonator printed on the UV-coated packaging paper exhibited the largest sensitivity from 20% to 70% RH, demonstrating the possibilities of directly printing the sensor tag on traditional packages to realize intelligent packaging at an ultra-low cost. / <p>QC 20150326</p>

This paper describes the development of an electrochemical sensor glassy carbon modified with gold nanoparticles and a film of multiâwalled carbon nanotube and cobalt phthalocyanine (CoPc-fMWCNTs/AuNp/GCE) for the determination of diethylstilbestrol hormone (DES) in water samples and meat, using a square wave technique voltammetry. (SWV). The electrolyte used was Britton-Robinson buffer (BR) 0.04 mol L-1 pH 10.0. Initially it was studied the electrode configuration to be used for the development work, after the optimization of solution pH, study scan speed to evaluate the charge transfer kinetics in the redox process of the DES, the optimized parameters for SWV, the analytical curve, and finally, applying the methodology developed. The optimized parameters for SWV were f = 5 sâ1, a = 50 mV and &#916;Es=1 mV. The CoPc-fMWCNTs/AuNp/GCE was ready to be used for the application since all conditions were optimized. Analytical curves were obtained in the concentration ranged from 7.9365 à 10&#8722;7 â 5.6604 à 10&#8722;6 mol Lâ1 (R = 0.9996) and there were obtained limits of detection (LOD) and quantification (LOQ) of 1.9910 x 10â7 mol Lâ1and 6.6367 x 10â7 mol Lâ1, respectively, being comparable to those reported in the literature. The repeatability and reproducibility of the proposed procedure were evaluated. The relative standard deviation (RSD) were 4.33% and 3.49%, respectively, indicating the precision of the assay. The recovery percentage was 98.56% for the water sample and 94.05% for beef sample (RSD of 0.40 and 1.55% respectively). The modified electrode has developed sensitivity, reproducibility and repeatability appropriate and consistent LOD and LOQ values with those reported in the literature. Moreover, the results obtained by the use of CoPc-fMWCNTs/AuNp/GCE proved very efficient as the detection and DES recovery, being thus a promising device in the detection and quantification of DES in water samples and food. / O presente trabalho descreve o desenvolvimento de um sensor eletroquÃmico de carbono vÃtreo modificado com nanopartÃculas de ouro, nanotubos de carbono de paredes mÃltiplas funcionalizados e ftalocianina de cobalto (CV/NpAu/NTCPMf-FcCo) para a determinaÃÃo do hormÃnio dietilestilbestrol (DES) em amostras de Ãgua e carne, utilizando a tÃcnica de voltametria de onda quadrada (VOQ). O eletrÃlito empregado foi tampÃo BrittonâRobinson (BR) 0,04 mol Lâ1 pH 10,0. Inicialmente estudou-se a configuraÃÃo do eletrodo a ser utilizado para o desenvolvimento do trabalho, depois a otimizaÃÃo do pH do meio, estudo da velocidade de varredura para avaliar a cinÃtica de transferÃncia de carga no processo redox do DES, otimizaÃÃo dos parÃmetros da VOQ, construÃÃo da curva analÃtica e por fim, a aplicaÃÃo da metodologia desenvolvida. Os parÃmetros otimizados para a VOQ foram: f = 5 sâ1, a = 50 mV e &#916;Es = 1 mV. De posse de todas as condiÃÃes otimizadas para aplicaÃÃo do CV/NpAu/NTCPMf-FcCo, curvas analÃticas foram obtidas no intervalo de concentraÃÃo de 7,9365 à 10&#8722;7 â 5,6604 à 10&#8722;6 mol Lâ1 (R = 0,9996) e os limites de detecÃÃo (LD) e de quantificaÃÃo (LQ) calculados foram 1,9910 x 10â7 mol Lâ1 e 6,6367 x 10â7 mol Lâ1, respectivamente, sendo comparÃveis aos citados na literatura. A repetibilidade e a reprodutibilidade do procedimento proposto foram avaliadas. Os valores de desvio padrÃo relativo (DPR) obtidos foram 4,33% e 3,49%, respectivamente, evidenciando a precisÃo da metodologia. O percentual de recuperaÃÃo foi de 98,56% para amostra de Ãgua e 94,05% para amostra de carne bovina (DPR de 0,40 e 1,55% respectivamente). O eletrodo modificado desenvolvido apresentou sensibilidade, reprodutibilidade e repetibilidade adequados, bem como valores de LD e LQ concordantes com os relatados na literatura. Os resultados obtidos pelo emprego do CV/NpAu/NTCPMf-FcCo se mostraram muito eficientes quanto à detecÃÃo e recuperaÃÃo de DES, mostrando-se, desse modo, um dispositivo promissor na detecÃÃo e na quantificaÃÃo de DES em amostras de Ãgua e alimentos.

Carbon nanotubes are molecular-scale tubes of graphitic carbon that possess many unique properties. They have high tensile strength and elastic modulus, are thermally and electrically conductive, and can be structurally modified using well established carbon chemistries. There is global interest in taking advantage of their unique combination of properties and using these interesting materials as components in nanoscale devices and composite materials. The goal of this research was the correlation of the mechanical properties of coiled carbon nanotubes with their chemical structure. Individual nanocoils, grown by chemical vapor deposition, were attached to scanning probe tip using the arc discharge method. Using a scanning probe microscope the nanocoils are repeatedly brought into and out of contact with a chemically-modified substrate. Precise control over the length (or area) of contact with the substrate is achievable through simultaneous monitoring the cantilever deflection resonance, and correlating these with scanner movement. The mechanical response of nanocoils depended upon the extent of their compression. Nonlinear response of the nanocoil was observed consistent with compression, buckling, and slip-stick motion of the nanocoil. The chemical structure of the nanocoil and its orientation on the tip was determined using scanning and transmission electron microscopy. The mechanical stiffness of eighteen different nanocoils was determined in three ways. In the first, the spring constant of each nanocoil was computed from the slope of the linear response region of the force-distance curve. The assumptions upon which this calculation is based are: 1) under compression, the cantilever-nanocoil system can be modeled as two-springs in series, and 2) the nanocoil behaves as an ideal spring as the load from the cantilever is applied. Nanocoil spring constants determined in this fashion ranged from 6.5x10-3 to 5.16 TPa for the CCNTs understudy. In the second, the spring constant of the nanocoil was computed from measuring the critical force required to buckle the nanocoil. The critical force method measured the force at the point where the nanocoil-cantilever system diverges from a linear region in the force curve. Nanocoil spring constants determined in this fashion ranged from 1.3x10-5 to 10.4 TPa for the CCNTs understudy. In the third, the spring constant of each nanocoil was computed from the thermal resonance of the cantilever-nanocoil system. Prior to contact of the nanocoil with the substrate, the effective spring constant of the system is essentially that of the cantilever. At the point of contact and prior to buckling or slip-stick motion, the effective spring constant of the system is modeled as two springs in parallel. Nanocoil spring constants determined in this fashion ranged from 2.7x10-3 to 0.03 TPa for the CCNTs understudy. Using the thermal resonance of the cantilever system a trend was observed relating nanocoil structure to the calculated modulus. Hollow, tube-like nanostructures had a higher measured modulus than solid or fibrous structures by several orders of magnitude. One can conclude that the structure of carbon nanocoils can be determined from using their mechanical properties. This correlation should significantly contribute to the knowledge of the scientific and engineering community. It will enable the integration of carbon nanocoils in microelectromechanical (MEMS) or nanoelectromechanical systems (NEMS) as resonators, vibration dampers, or any other application in which springs are used within complex devices.

No description available.

Since their discoveries, carbon nanotubes have been widely studied, but mostly in the forms of 1D individual carbon nanotube (CNT). From practical application point of view, it is highly desirable to produce carbon nanotubes in large scales. This has resulted in a new class of carbon nanotube material, called the vertically aligned carbon nanotube arrays (VA-CNTs). To date, our ability to design and model this complex material is still limited. The classical molecular mechanics methods used to model individual CNTs are not applicable to the modeling of VA-CNT structures due to the significant computational efforts required. This research is to develop efficient structural mechanics approaches to design, model and characterize the mechanical responses of the VA-CNTs. The structural beam and shell mechanics are generally applicable to the well aligned VA-CNTs prepared by template synthesis while the structural solid elements are more applicable to much complex, super-long VA-CNTs from template-free synthesis. VA-CNTs are also highly “tunable” from the structure standpoint. The architectures and geometric parameters of the VA-CNTs have been thoroughly examined, including tube configuration, tube diameter, tube height, nanotube array density, tube distribution pattern, among many other factors. Overall, the structural mechanics approaches are simple and robust methods for design and characterization of these novel carbon nanomaterials