Increasing energy demands as well as the depletion of traditional energy sources has led to the need for the development and improvement of energy conversion and storage technologies. Concerns regarding climate change and environmental awareness has also created increased support for renewable energy and clean technology research. One technology of interest is the photocatalyst, which is a material that is able to use natural light irradiation to create electrical currents or drive useful chemical reactions. For this purpose, a strong photocatalytic material has the following properties: i) strong absorbance over a wide solar radiation spectrum; ii) high surface area for adsorbance of target species; iii) high electron efficiency characteristics such as high conductivity, long charge-carrier lifetimes, and direct pathways for electron transport; and iv) good chemical stability. All of these requirements serve to maximize the efficiency and overall output of the device, and are a means of overcoming the performance hurdle required for the commercialization of various energy conversion technologies. Unfortunately, current photocatalytic materials suffer from small absorbance windows and high recombination rates which greatly reduce the conversion efficiency of the catalyst. Titanium dioxide (TiO2), the most well-known and widely used photocatalyst, can only absorb light within the ultraviolet (UV) range – which accounts for only a small fraction of the entire solar spectrum. For this reason, the majority of recent research has been directed toward producing photocatalysts that are able to absorb light within the visible and infrared range in order to maximize the amount of light absorbed in the solar spectrum. Other research is also being conducted to increase electrical conductivity and charge-carrier separation to further increase conversion efficiency. It is hoped that these two major problems surrounding photocatalysis can be solved by using novel functional nanomaterials. Nanomaterials can be synthesized using three main techniques: crystal structuring, doping, and heterostructuring. By controlling the structure of the crystal, materials of different phase, morphology, and exposed crystal facets can be synthesized. These are important for controlling the electronic properties and surface reactivity of the photocatalyst. Doping is the act of introducing impurities into a material in order to modify its band structure and create a red shift in light absorption. Lastly, heterostructuring is a method used to combine different photocatalysts or introduce co-catalysts in order to widen the range of absorption, encourage charge separation, or both. Many novel photocatalytic materials have been synthesized using these techniques. However, the next-generation photocatalytic material has remained elusive due to the high cost of production and complexity of synthesis. This thesis proposes a novel photocatalytic material that can be used in photocatalyzed waste-water remediation. Graphene-wrapped hierarchical TiO2 nanoflowers (G-TiO2) are synthesized using a facile synthesis method. TiO2 is a material of particular interest due to its chemical and photo-corrosion stability, high redox potential, strong electronic properties, and relative non-toxicity. Hierarchical structures are highly desired because they are able to achieve both high surface area and high conductivities. Graphene hybridization is a popular method for creating composites with highly conductive networks and highly adsorptive surfaces. To the best of my knowledge, the hybridization of graphene on hierarchical TiO2 structures without pre-functionalization of TiO2 has not yet been demonstrated in literature. Therefore, it is proposed that the use of such a material would greatly simplify the synthesis process and enhance the overall photocatalytic performance of TiO2 over that of commercial TiO2 photocatalysts. In the first study, hierarchical TiO2 nanoflowers are synthesized using a solvothermal reaction. It is then shown that under UV irradiation, the hierarchical TiO2 material is able to outperform commercial TiO2 material in the photodegradation of methylene blue (MB). Further characterization shows that this improvement is explained by a higher electrical conductivity, and exists in spite of having a lower specific surface area compared to the commercial material. In the second study, G-TiO2 is synthesized by mixing hierarchical TiO2 nanoflowers with graphene oxide (GO) and reducing GO in a hydrothermal reaction. Photocatalytic tests show that this hybridization further improves the performance of the hierarchical TiO2. Further studies reveal that an optimal graphene loading of 5 wt% is desired in order to achieve the higher rate of MB decomposition, and greatly outperforms P25 in this task. Characterization shows that G-TiO2 composites have increased specific surface area and electrical conductivity compared to the hierarchical TiO2 nanoflower. It is believed that this work will provide a simple and efficient avenue for synthesizing graphene–TiO2 composites with greatly improved photocatalytic activity. This work may also find use in other photocatalytic applications such as chemical deconstruction and manufacturing, hydrogen production, solar cells, and solar enhanced fuel cells.

Nanomechanics emerged as chemists and physicists began fabricating nanoscale objects. However, there are some materials that have neither been fabricated nor mechanical investigated at the nanoscale, such as rhodium. Rhodium is used in many applications, especially in coatings and catalysis. To contribute to the understanding the nano-properties of this important material, rhodium was fabricated and mechanically investigated at the nanoscale. The nanopillars approach was employed to study size effects on mechanical properties. Nanopillars with different diameters were fabricated using electroplating followed by uniaxial compression tests. SEM was used as a quality control technique by imaging the pillars before and after compression to assure the absence of buckling, barrelling, or any other problems. Transmission electron microscopy (TEM) and SEM were used as microstructural characterization techniques, and the energy-dispersive X-ray spectroscopy (EDX) was used as the chemical characterization technique. Due to substrate induced effects, only the plastic region of the stress-strain curves were investigated, and it was revealed that rhodium softens with decreased nanopillar diameter. This softening/weakening effect was due to the nanocrystallinity of the fabricated pillars. This effect is consistent with the literature that demonstrates the reversed size effect of nanocrystalline metals, i.e., smaller is weaker. Further studies should focus on eliminating the substrate effect that was due to the adhesion layers between Rh and the silicon substrate being softer than Rh, consequently, causing Rh to sink into the adhesion layer when compressed and thus perturbing the stress-strain curve. Moreover, further investigation of other properties of Rh is required to achieve a comprehensive understanding of Rh at the nanoscale, and to render it suitable for specific, multivariable applications.

Polyanionic compounds have been heavily investigated as possible electrode materials in lithium- and sodium-ion batteries. Chief among these is lithium iron phosphate (LiFePO4) which adopts the olivine structure and has a potential of 3.5 V vs. Li/Li+. Many aspects of ion transport, solid-solution behaviour and their relation to particle size in olivine systems are not entirely understood. Morphology, unit cell parameters, purity and electrochemical performance of prepared LiFePO4 powders were greatly affected by the synthetic conditions. Partially delithiated olivines were heated and studied by Mössbauer spectroscopy and solid-solution behaviour by electron delocalization was observed. The onset of this phenomenon was around 470-500 K in bulk material but in nanocrystalline powders, the onset of a solid solution was observed around 420 K. The isostructural manganese member of this family (LiMnPO4) was also prepared hydrothermally. Owing to the thermal instability of MnPO4, partially delithiated LiMnPO4 did not display any solid-solution behaviour. Phosphates based on the tavorite (LiFePO4OH) structure include LiVPO4F and LiFePO4(OH)1-xFx which may be prepared hydrothermally or by solid state routes. LiVPO4F is a high capacity (2 electrons/transition metal) electrode material and the structures of the fully reduced Li2VPO4F and fully oxidized VPO4F were ascertained. Owing to structural nuances, the potential of the iron tavorites are much lower than that of the olivines. The structure of Li2FePO4F was determined by a combined X-ray and neutron diffraction analysis. The electrochemical properties of very few phosphates based on sodium are known. A novel fluorophosphate, Na2FePO4F, was prepared by both solid state and hydrothermal methods. This material exhibited two two-phase plateau regions on cycling in a half cell versus sodium but displayed solid-solution behaviour when cycled versus lithium, where the average potential was 3.3 V. On successive cycling versus Li a decrease in the sodium content of the active material was observed, which implied an ion-exchange reaction occurred between the material and the lithium electrolyte. Studies of polyanionic materials as positive electrode materials in alkali metal-ion batteries show that some of these materials, namely those which contain iron, hold the most promise in replacing battery technologies currently available.

With excellent electrical, thermal and mechanical properties as well as large specific surface area, graphene has been applied in next-generation nano-electronics, gas sensors, transparent electrical conductors, thermally conductive materials, and superior energy capacitors etc. Convenient and productive preparation of graphene is thereby especially important and strongly desired for its manifold applications. Chemically developed functionalized graphene from graphene oxide (GO) has significantly high productivity and low cost, however, toxic chemical reduction agents (e.g. hydrazine hydrate) and raised temperature (400-1100°C) are usually necessary in GO reduction yet not preferred in current technologies. Here, microwaves (MW) are applied to reduce the amount of graphene oxide (GO) at a relatively low temperature (~165°C). Experimental results indicate that resurgence of interconnected graphene-like domains contributes to a low sheet resistance with a high optical transparency after MW reduction, indicating the very high efficiency of MW in GO's reduction. Moreover, graphene is usually recumbent on solid substrates, while vertically aligned graphene architecture on solid substrate is rarely available and less studied. For TIMs, electrodes of ultracapacitors, etc, efficient heat dissipation and electrical conductance in normal direction of solid surfaces is strongly desired. In addition, large-volume heat dissipation requires a joint contribution of a large number of graphene sheets. Graphene sheets must be aligned in a large scale array in order to meet the requirements for TIM application. Here, thermally conductive fuctionalized multilayer graphene sheets (fMGs) are efficiently aligned in a large scale by vacuum filtration method at room temperature, as evidenced by SEM images and polarized Raman spectroscopy. A remarkably strong anisotropy in properties of aligned fMGs is observed. Moreover, VA-fMG TIMs are prepared by constructing a three-dimensional vertically aligned functionalized multilayer graphene architecture between contact Silicon/Silicon surfaces with pure Indium as a metallic medium. Compared with their counterpart from recumbent A-fMGs, VA-fMG TIMs have significantly higher equivalent thermal conductivity and lower contact thermal resistance. Electrical and thermal conductivities of polymer composite are also greatly interested here. Previous researches indicated that filler loading, morphology of fillers, and chemical bonding across filler/polymer interfaces have significant influence on electrical/thermal conductivity of polymer composite. Therefore, the research also pays substantial attention to these issues. First, electrical resistivity of CPCs is highly sensitive on volume or weight ratio (filler loading) of conductive fillers in polymer matrix, especially when filler loading is close to percolation threshold (pc). Thermal oxidation aging usually can cause a significant weight loss of polymer matrix in a CPC system, resulting in a filler loading change which can be exhibited by a prompt alteration in electrical resistivity of CPCs. Here, the phenomena are applied as approach for in-situ monitoring thermal oxidation status of polymeric materials is developed based on an electrical sensors based on conductive polymeric composites (CPCs). The study developed a model for electrical resistivity of sensors from the CPCs as a function of aging time at constant aging temperature, which is in a good agreement with a Boltzmann-Sigmoidal equation. Based on the finding, the sensors show their capability of in-situ in-situ monitor and estimate aging status of polymeric components by a fast and convenient electrical resistance measurement. Second, interfacial issues related to these thermal conductive fillers are systemically studied. On the one hand, the study focuses on relationship between morphology of h-BN particles and thermal conductivity of their epoxy composites. It is found that spherical-agglomeration of h-BN particles can significantly enhance thermal conductivity of epoxy resin, compared with dispersed h-BN plates, by substantially reducing specific interfacial area between h-BN and epoxy resin. On the other hand, surface of high thermal conductive fillers such as SiC particles and MWNTs are successfully functionalized, which makes their surface reactive with bisphenol A diglycidyl ether and able to form chemical bonding between fillers and epoxy resin. By this means, thermal conductivity of polymer composites is found to be significantly enhanced compared with control samples, indicating the interfacial chemical bonding across interface between thermal conductive fillers and polymer matrix can promote heat dissipation in polymeric composites. The finding can benefit a development of high thermal conductive polymer composites by interfacial chemical bonding enhancement to meet the demanding requirements in current fine pitch and Cu/low k technology.

Pour répondre aux nouvelles contraintes économiques et environnementales auxquelles l'industrie doit faire face aujourd'hui, des techniques de frittage rapide se développent pour la fabrication des céramiques. Parmi elles, une technique prometteuse est le frittage par micro-ondes dans laquelle le champ électromagnétique à l'origine du chauffage pourrait permettre d'obtenir des microstructures innovantes, tout en réduisant la température, le temps de cycle et la consommation énergétique. Pour expliquer le comportement particulier des poudres en présence des micro-ondes, différentes théories prévoyant des effets thermiques ou non-thermiques ont été proposées. L'existence même de ces effets n'a cependant toujours pas été démontrée de façon sûre, notamment à cause des limites des dispositifs expérimentaux qui ne permettent pas une comparaison pertinente du frittage micro-ondes avec le frittage conventionnel. Dans ce contexte, les travaux réalisés pendant cette thèse, dans le cadre du projet ANR Fµrnace, ont été consacrés à la mise en évidence et à la compréhension de l'influence du champ électromagnétique sur les mécanismes responsables de la densification et de l'évolution microstructurale de poudres céramiques. Une forte attention a été portée au développement technologique de la cavité de chauffage micro-ondes monomode utilisée dans nos recherches. Le procédé a été entièrement automatisé et équipé de divers systèmes de contrôle de la température et du retrait des échantillons pour que les résultats obtenus puissent être comparés de façon incontestable avec ceux issus d'essais de frittage conventionnel. Des simulations numériques ont été réalisées pour améliorer la compréhension de la propagation du champ électromagnétique et de son interaction avec les éléments introduits au sein de la cavité micro-ondes. Un matériau de référence, l'alumine, a été choisi et l'influence de certaines caractéristiques des poudres (surface spécifique, présence de dopants, transformation de phase) sur les cinétiques de densification et l'évolution microstructurale a été étudiée. Les résultats obtenus ont permis d'identifier des effets spécifiques des micro-ondes sur les mécanismes de diffusion responsables de la densification et de la croissance granulaire. Ces effets se produisent principalement pendant les stades initial et intermédiaire du frittage, ainsi que pendant la transformation de phase de poudres de transition et ont été attribués à une force de type pondéromotrice déjà proposée dans la littérature. L'utilisation de cette technique de frittage n'a cependant pas permis d'obtenir des alumines avec des microstructures plus performantes que celles issues du frittage conventionnel. / To meet the new economic and environmental constraints that the industry faces today, fast sintering processes are developed for the fabrication of ceramics. Among them, a promising technique is microwave sintering, in which the electromagnetic field at the origin of heating could be used to obtain innovative microstructures, while reducing sintering temperature, cycle time and energy consumption. To explain the particular behavior of powders under microwaves, different hypotheses related with thermal or non-thermal effects have been proposed in the literature. These effects, however, has not really been demonstrated for the moment, especially because of the limits of experimental devices that do not allow for a meaningful comparison of microwave sintering with conventional sintering. In this context, the work performed during this thesis in the framework of FμRNACE ANR project has been dedicated to identifying and understanding the influence of the electromagnetic field on the mechanisms of densification and microstructure changes in ceramic powders. High attention has been paid to the technological development of the single-mode microwave cavity used in our research. The heating process has been fully automated and instrumented with various equipments allowing for temperature and sample shrinkage measurement. The aim was to ensure direct and reliable comparison of microwave sintering data with those resulting from conventional sintering. Numerical simulation has been conducted to improve our understanding of the propagation of the electromagnetic field and its interaction with the components introduced in the microwave cavity. Alumina has been chosen as a reference material and the influence of several features of the powders (specific surface area, doping elements, phase transformation) on densification kinetics and microstructure changes has been studied. The results have identified specific effects of microwaves on the mechanisms controlling densification and grain growth. These effects occur essentially during the initial and intermediate stages of sintering and during the phase transformation of transition powders. They have been attributed to the ponderomotive force as already proposed in the literature. However the use of microwaves as a heating mode does not permit obtaining alumina with better microstructures than those resulting from conventional sintering.

Cette thèse s’intéresse à l’exaltation du signal Raman sur des nanomatériaux cuivrés. Des couches minces d’épaisseur de cuivre variable ont été préparées et étudiées avant et après oxydation dans l’air à des températures inférieures à 200°C. Leur microstructure a été caractérisée par microscopies MEB et AFM. L’épaisseur des couches de cuivre et d’oxyde cuivreux a été mesurée localement par ces techniques, et comparée aux résultats d’études spectroscopiques par ellipsométrie et absorption UV-visible. Une modélisation des spectres d’absorption UV-visible, basée sur des calculs d’interférences à partir des équations de Fresnel, permet de déterminer à la fois les épaisseurs des couches et leurs indices de réfraction. L’étude Raman de ces échantillons permet de discuter et de quantifier le phénomène d’exaltation Raman par interférences (IERS). D’autres échantillons nanostructurés à base de cuivre, recouverts de graphène monofeuillet, ont été étudiés. Les variations d’intensité Raman du graphène sont discutées en termes d’IERS. La dernière partie du manuscrit est consacrée à l’étude du signal SERS de molécules déposées sur des substrats commerciaux nanostructurés d’or, et à leur évolution après avoir recouvert ces substrats d’une couche mince de cuivre. / This thesis studies the enhanced Raman signatures on copper based materials. Thin copper films were prepared and studied before and after thermal oxidation in air, under 200 °C. Their microstructure has been characterized by SEM and AFM. The thickness of the copper and cuprous oxide films have been characterized locally by those techniques, and by ellipsometry and UV-visible absorption spectroscopic techniques. A modeling of the UV-visible spectra has been performed based on interference calculations using Fresnel equations, allowing the determination of both the thicknesses and the refractive indices of the films. Raman study of these samples allows a quantification of the interference enhanced Raman phenomenon (IERS). Other copper nanostructured samples covered with single layer graphene (SLG) have been studied, and The Raman intensity of SLG discussed in terms of IERS. The last part of the manuscript is dedicated to SERS studies of molecules deposited on nanostructured golden commercial substrates and to the evolution of the Raman the signal after covering these substrates with a thin copper layer.

abstract: As the use of engineered nanomaterials (ENMs) in consumer products becomes more common, the amount of ENMs entering wastewater treatment plants (WWTPs) increases. Investigating the fate of ENMs in WWTPs is critical for risk assessment and pollution control. The objectives of this dissertation were to (1) quantify and characterize titanium (Ti) in full-scale wastewater treatment plants, (2) quantify sorption of different ENMs to wastewater biomass in laboratory-scale batch reactors, (3) evaluate the use of a standard, soluble-pollutant sorption test method for quantifying ENM interaction with wastewater biomass, and (4) develop a mechanistic model of a biological wastewater treatment reactor to serve as the basis for modeling nanomaterial fate in WWTPs. Using titanium (Ti) as a model material for the fate of ENMs in WWTPs, Ti concentrations were measured in 10 municipal WWTPs. Ti concentrations in pant influent ranged from 181 to 3000 µg/L, and more than 96% of Ti was removed, with effluent Ti concentrations being less than 25 µg/L. Ti removed from wastewater accumulated in solids at concentrations ranging from 1 to 6 µg Ti/mg solids. Using transmission electron microscopy, spherical titanium oxide nanoparticles with diameters ranging from 4 to 30 nm were found in WWTP effluents, evidence that some nanoscale particles will pass through WWTPs and enter aquatic systems. Batch experiments were conducted to quantify sorption of different ENM types to activated sludge. Percentages of sorption to 400 mg TSS/L biomass ranged from about 10 to 90%, depending on the ENM material and functionalization. Natural organic matter, surfactants, and proteins had a stabilizing effect on most of the ENMs tested. The United States Environmental Protection Agency's standard sorption testing method (OPPTS 835.1110) used for soluble compounds was found to be inapplicable to ENMs, as freeze-dried activated sludge transforms ENMs into stable particles in suspension. In conjunction with experiments, we created a mechanistic model of the microbiological processes in membrane bioreactors to predict MBR, extended and modified this model to predict the fate of soluble micropollutants, and then discussed how the micropollutant fate model could be used to predict the fate of nanomaterials in wastewater treatment plants. / Dissertation/Thesis / Ph.D. Civil and Environmental Engineering 2011

Ce travail de thèse porte sur la synthèse de nouveaux matériaux nanostructurés sous conditions extrêmes de pression et de température (P > 5 GPa et T > 1000 °C). Les matériaux que nous étudions sont basés sur un élément particulier : le bore. Ces matériaux présentent des propriétés uniques. D'une part, les allotropes du bore présentent des duretés élevées et une grande inertie chimique. D'autre part, les alliages du bore (ou borures métalliques) présentent des propriétés variées, de la thermoélectricité (HfB2) à la supraconductivité (MgB2). La synthèse en sels fondus est utilisée afin d'obtenir des systèmes nanostructurés comprenant deux composants : des nanoparticules cristallines d'environ 10 nm de borures métalliques (HfB2 ou CaB6) comprises dans une matrice de bore amorphe.Le traitement sous haute pression et température est le seul permettant de cristalliser la phase amorphe. La conservation de la nanostructure initiale est démontrée. Plusieurs nouveaux matériaux sont ainsi synthétisés : des nanocomposites borure/borate (HfB2/HfB2O5 ou CaB6/CaB2O4) ou borure/bore (HfB2/?-B ou CaB6/?-B), premiers membres de nouvelles familles de nanomatériaux. Un précurseur de bore amorphe nanostructuré synthétisé en sels fondus est ensuite utilisé. Il est cristallisé sous haute pression et haute température. En sus de la première occurrence de bore epsilon nanostructuré, deux nouvelles phases riches en bore sont obtenues, dont la structure est en cours de résolution. En somme, ce travail conduit à une nouvelle méthode de synthèse à la frontière entre la chimie des nanomatériaux et la physique des hautes pressions et températures, à l'origine de nouveaux nanomatériaux et structures. / In this PhD work, we develop a way to prepare new nanostructured materials under extreme pressure and temperature conditions (P > 5 GPa et T > 1000 °C). The studied materials are based on a specific element: boron. Indeed, these materials have unique properties. On the one hand, boron allotropes exhibit high hardness and chemical inertness. On the other hand, metal-boron alloys (metal borides) span a wide range of properties, from thermoelectricity (HfB2) to superconductivity (TiB2). We use the synthesis in molten salts to reach nanostructured systems with two components: crystalline boride nanoparticles (ca. 10 nm) embedded in an amorphous boron matrix. High pressure high temperature treatments on these systems enable crystallisation of the amorphous component into unique phases, thus yielding new nanomaterials: boride/borate (HfB2/HfB2O5 or CaB6/CaB2O4) or boride/boron (HfB2/β-B or CaB6/β-B) nanocomposites, representing the first members of new nanomaterials families. In a final step, a specific nanostructured amorphous boron precursor is synthesised in molten salts. It is crystallised under high pressure and temperature. In addition to the first nanostructured occurrence of the epsilon-boron phase, we report two new boron-rich phases, which structure is under resolution. All in all, a new synthetic route is developed at the frontier of nanomaterials chemistry and high pressure and temperature physics, leading to new nanomaterials and structures.

This thesis presents a study of hybrid solar cells, specifically looking at various methods which can be employed in order to increase the power conversion efficiency of these devices. The experiments and results contained herein also present a very accurate picture of how rapidly the field of hybrid solar cells has progressed within the past three years. Chapters 1 and 2 present the background and motivation for the investigations undertaken, as well as the relevant theory underpinning solar cell operation. Chapter 2 also gives a brief review of the literature pertinent to the main types of devices investigated in this thesis; dye-sensitised solar cells, semiconductor sensitized solar cells and perovskite solar cells. Descriptions of the synthetic procedures, as well as the details of device fabrication and any measurement techniques used are outlined in Chapter 3. The first set of experimental results is presented in Chapter 4. This chapter outlines the synthesis of mesoporous single crystals (MSCs) of anatase TiO₂ as well as an investigation of its electronic properties. Having shown that this material has superior electronic properties to the conventionally used nanoparticle films, they were then integrated into low temperature processed dye-sensitised solar cells and achieved power conversion efficiencies of > 3%, exhibiting electron transport rates which were orders of magnitude higher than those obtained for the high temperature processed control films. Chapter 5 further investigates the use of MSCs in photovoltaic devices, this time utilising a more strongly absorbing inorganic sensitiser, Sb₂S₃. Utilising the readily tunable pore size of MSCs, these Sb₂S₃ devices showed an increase in voltage and fill factor which can be attributed to a decrease in recombination within these devices. This chapter also presents the use of Sb₂S₃ in the meso-superstructured configuration. This device architecture showed consistently higher voltages suggesting that in this architecture, charge transport occurs through the absorber and not the mesoporous scaffold. Chapters 6 and 7 focus on the use of hybrid organic-inorganic perovskites in photovoltaic devices. In Chapter 6 the mixed halide, lead-based perovskite, CH₃NH₃PbI_3-xCl_x is employed in a planar heterojunction device architecture. The effects of Lewis base passivation on this material are investigated by determining the photoluminescence (PL) lifetimes and quantum efficiencies of treated and untreated films. It is found that passivating films of this material using Lewis bases causes an increase in the PLQE at low fluences as well as increasing the PL lifetime. By globally fitting these results to a model the trap densities are extracted and it is found that using these surface treatments decreases the trap density of the perovskite films. Finally, these treatments are used in complete solar cells resulting in increased power conversion efficiencies and an improvement in the stabilised power output of the devices. Chapter 7 describes the materials synthesis and characterisation of the tin-based perovskite CH₃NH₃SnI₃ and presents the first operational, lead-free perovskite solar cell. The work presented in this thesis describes significant advances in the field of hybrid solar cells, specifically with regards to improvements made to the nanostructured electrode, and the development and implementation of more highly absorbing sensitizers. The improvements discussed here will prove to be quite important in the drive towards exploiting solar power as a clean, affordable source of energy.

L’incorporation croissante des (nanomatériaux) NMx dans les aliments et les emballages a contribué à une demande sociétale majeure au regard de l’évaluation des risques des NMx sur la santé. Toutefois, en raison des nombreux paramètres des NMx (taille, forme, structure cristalline, solubilité…), ainsi que des processus physiologiques (comme la digestion) pouvant impacter sur l’absorption et la réponse toxique des NMx, l’évaluation des risques des NMx est compliquée. De plus, leur évaluation in vitro est délicate en raison d’interférences (optiques, catalytiques…) lors de la réalisation des tests. Notre projet de recherche visait à déterminer, l’impact des paramètres d’hydrophobicité des NMx de TiO2 de structure cristalline rutile et l’impact de la solubilité des NMx d’Al0 et Al2O3 sur leur toxicité/génotoxicité au niveau intestinal (organe primo-exposé) et hépatique (organe d’accumulation). Les effets de ces NMx ont été étudiés par une combinaison de méthodes complémentaires in vivo par gavage sur rat, et in vitro sur les lignées humaines Caco-2 et HepaRG différenciées, tout en tenant compte des interférences in vitro. Aucune réponse toxique et génotoxique n’a été observée in vitro malgré la différence de revêtement hydrophobe/hydrophile des NMx de TiO2. Seuls les NMx d’Al2O3 ont induit des lésions oxydatives de l’ADN mais uniquement dans les cellules Caco-2, tandis que de fortes interférences ont empêché de conclure avec les NMx d’Al0. Aucun dommage chromosomique n’a été observé pour ces NMx. In vivo aucun effet génotoxique n’a été observé dans l’intestin, le colon et le foie mais des dommages à l’ADN ont été décelés avec les NMx d’Al2O3 dans la moelle osseuse. La comparaison des résultats avec ceux de la forme ionique AlCl3 suppose un mécanisme de génotoxcité indépendant de la solubilité des NMx d’Al0 et d’Al2O3 dans les milieux biologiques. Malgré les nombreux progrès en nanotoxicologie, l’ensemble de nos résultats a souligné la difficulté d’obtenir des conclusions fiables avec des tests classiques utilisés pour les produits chimiques in vitro, la difficulté d’extrapolation in vitro/in vivo des effets des NMx et le besoin de poursuivre les recherches pour disposer de méthodes et d’outils permettant d’évaluer les effets des NMx de manière fiable. / The growing incorporation of nanomaterials (NMs) into food and packaging has contributed to the increasing demand for the assessment of the health hazards of these particles. However, this task is rendered difficult since the numerous intrinsic parameters (size, shape, crystalline structure, solubility ...), as well as physiological processes (such as digestion) can have an impact on the absorption and toxicological responses of NMs. Moreover, their evaluation in vitro is complicated by various sources of interference (optical, catalytic …) with toxicity tests. Our research project aimed to evaluate, the impact of hydrophobicity of rutile TiO2 NMs and solubility of AlO and Al2O3 NMs on their intestinal (first-exposed organ) and hepatic (accumulation organ) toxicity/genotoxicity. The effects of these NMs were investigated by a combination of complementary methods, in the rat in vivo by gavage, and in vitro using differentiated human Caco-2 and HepaRG cell lines, while taking into account potential interference with in vitro tests. No toxic/genotoxic response was observed in vitro despite the difference of hydrophobic/hydrophilic surface coating for TiO2 NMs. Only Al2O3 induced oxidative DNA damage solely in Caco-2 cells, while significant interference led to inconclusive results for AlO NMx. No chromosomal damage was observed for Al0 or Al2O3 NMx. In vivo no genotoxic effect was observed in the intestine, colon and liver but DNA damage was detected with Al2O3NMx in the bone marrow. Comparison of results with those for the ionic form AlCl3 demonstrated that effects observed were not related to the solubility of Al0 and d’ Al2O3 NMs in the biological environment. Despite considerable progress in nanotoxicology, our results have highlighted the difficulty to obtain reliable re sults with the traditional toxicity tests used for chemical compounds in vitro, the difficulty associated with the in vitro/in vivo extrapolation of the effects of NMs, as well as the need to continue research aimed at developing robust and reliable methods and tools for the evaluation of the effects of NMs.