L’optimisation des systèmes de production d’énergie par combustion requiert une connaissance précise de la cinétique de combustion. Cependant, la majorité des systèmes de production d’énergie par combustion fonctionnent à haute pression et il est reconnu que la pression a une influence sur la cinétique de combustion. En laboratoire, l’analyse de la structure de flamme laminaire se présente comme un outil puissant pour étudier la chimie de la combustion. A ce jour, la plupart des travaux menés ont été réalisés à des pressions inférieures ou égales à la pression atmosphérique. Au cours de cette thèse, un dispositif expérimental pour l’analyse de structure de flammes laminaires, à contre-courants et à haute pression a été mis en place. Il permet de stabiliser des flammes de CH4/air et CH4/CO2/air jusqu’à 0,7 MPa et l’étude de leur structure par diagnostics laser. Les profils de concentration de OH dans les flammes CH4/air et CH4/CO2/air à différentes richesses (=0,7-1,2) et différentes pressions (P=0,1-0,7 MPa) ont été mesurés par Fluorescence Induite par Laser et calibrés en concentration par absorption laser. Pour cela, la longueur du milieu absorbant a été déterminée par Fluorescence Induite par Plan Laser (PLIF). Une attention particulière a été portée aux corrections du signal de fluorescence prenant en compte l’élargissement de raie et le taux de collisions, qui augmentent avec la pression. Les profils expérimentaux obtenus ont été comparés à la modélisation à l’aide du code de calcul OPPDIF et des mécanismes cinétiques GRI-Mech3.0 et GDFKin®3.0. En parallèle, une analyse spectroscopique des flammes de CH4/air à haute pression a été entreprise. / The optimisation of practical combustion devices requires a detailed knowledge of the combustion kinetic. However, most practical combustion systems operate at high pressure and it is known that pressure has an influence on combustion kinetics. In laboratory, the analysis of laminar flame structure is a powerful tool for studying combustion chemistry. However, most of studies have been realised at pressures under or equal to atmospheric pressure. During this thesis, an experimental device has been implemented for the study of the structure of high pressure counterflow flames. It allows the stabilisation and the study of CH4/air and CH4/CO2/air flame structure through laser diagnostics until 0.7 MPa. CH4/air and CH4/CO2/air flames have been studied for a various range of stoichiometry (equivalence ratios from 0.7 to 1.2) and pressures (0.1 MPa to 0.7 MPa). Experimental OH concentration profiles have been measured by Laser Induced Fluorescence and calibrated by laser absorption. To do this, absorption path length has been determined by Planar Laser Induced Fluorescence (PLIF). Great care has been attached to the determination of the fluorescence signal by taking into account the line broadening and de-excitation by quenching which both arise at high pressure. Experimental data were compared with modeling results obtained through the OPPDIF calculation code with GRI-Mech3.0 and GDFKin®3.0 kinetic mechanisms. In parallel, a spectroscopic analysis of the CH4/air flames has been undertaken.

O interesse no desenvolvimento de sistemas eficientes de combustão para reduzir a poluição ambiental e aumentar a eficiência de queima tem chamado a atenção para a combustão em meios porosos inertes. A recirculação de calor, induzida pela matriz sólida a partir dos produtos quentes para os reagentes frios, aumenta a temperatura da chama melhorando a sua estabilidade e permitindo a utilização de combustíveis com baixo poder calorífico. Um estudo teórico recente mostra que uma chama estabilizada por um plano de estagnação imersa em um meio poroso pode, sob certas condições, estender os limites de inflamabilidade de uma mistura de ar e combustível. Por outro lado, o plano de estagnação é um problema que simula o efeito da taxa de deformação do escoamento sobre a estabilidade da chama, o que é relevante para várias configurações de queimador poroso. Portanto, o foco deste trabalho é o estudo da combustão em um queimador poroso com um plano de estagnação. Um experimento é conduzido com empacotamento de esferas, onde uma chama pode ser estabilizada por plano de estagnação devido a um anteparo. A razão de equivalência e a taxa de deformação são controladas pelos fluxos de ar e de combustível e da distância entre injetor e anteparo. A posição da chama é aproximadamente determinada pelo campo de temperaturas medidas por termopares. Complementarmente é realizada uma análise numérica simplificada do problema na qual se pode verificar o efeito da taxa de deformação sobre a estabilidade de chamas em queimadores porosos. Os resultados mostram que é possível estabilizar chamas no interior do meio poroso com plano de estagnação, porém, não foi possível atribuir um aumento de temperatura devido ao aumento da taxa de deformação. / The interest in developing efficient combustion systems to reduce environmental pollution and increase the burning efficiency has called attention to the combustion in inert porous media. The heat recirculation, induced by the solid matrix, from the hot products to the incoming cold reactants, increases the flame temperature and improves its stability, allowing for the use of fuels with low heat content. A recent study shows theoretically that a flame stabilized by a stagnation plane immersed in a porous medium may, under certain conditions, to extend the flammability limits of a mixture of fuel and air. On the other hand, the stagnation plane imposes a certain strain rate on the flow field, which is relevant to various porous burner configurations. Therefore, the focus of this work is the study of combustion in a porous burner with a stagnation plane. An experiment is conducted with packing bed of spheres where a flame can be stabilized against a stagnation plane. The equivalence ratio and the strain rate are controlled by the flows of air and fuel and the distance between the injector and the stagnation plane. The flame position is approximately determined by the temperature field measured by thermocouples. In addition, it is performed a simplified numerical analysis of the problem in which one can see the effect of the strain rate on the stability of flames in porous burners. The results show that it is possible to stabilize flames within the porous medium with stagnation plane, however, it has not been possible to assign a temperature increase due to the increased strain rate.

O interesse no desenvolvimento de sistemas eficientes de combustão para reduzir a poluição ambiental e aumentar a eficiência de queima tem chamado a atenção para a combustão em meios porosos inertes. A recirculação de calor, induzida pela matriz sólida a partir dos produtos quentes para os reagentes frios, aumenta a temperatura da chama melhorando a sua estabilidade e permitindo a utilização de combustíveis com baixo poder calorífico. Um estudo teórico recente mostra que uma chama estabilizada por um plano de estagnação imersa em um meio poroso pode, sob certas condições, estender os limites de inflamabilidade de uma mistura de ar e combustível. Por outro lado, o plano de estagnação é um problema que simula o efeito da taxa de deformação do escoamento sobre a estabilidade da chama, o que é relevante para várias configurações de queimador poroso. Portanto, o foco deste trabalho é o estudo da combustão em um queimador poroso com um plano de estagnação. Um experimento é conduzido com empacotamento de esferas, onde uma chama pode ser estabilizada por plano de estagnação devido a um anteparo. A razão de equivalência e a taxa de deformação são controladas pelos fluxos de ar e de combustível e da distância entre injetor e anteparo. A posição da chama é aproximadamente determinada pelo campo de temperaturas medidas por termopares. Complementarmente é realizada uma análise numérica simplificada do problema na qual se pode verificar o efeito da taxa de deformação sobre a estabilidade de chamas em queimadores porosos. Os resultados mostram que é possível estabilizar chamas no interior do meio poroso com plano de estagnação, porém, não foi possível atribuir um aumento de temperatura devido ao aumento da taxa de deformação. / The interest in developing efficient combustion systems to reduce environmental pollution and increase the burning efficiency has called attention to the combustion in inert porous media. The heat recirculation, induced by the solid matrix, from the hot products to the incoming cold reactants, increases the flame temperature and improves its stability, allowing for the use of fuels with low heat content. A recent study shows theoretically that a flame stabilized by a stagnation plane immersed in a porous medium may, under certain conditions, to extend the flammability limits of a mixture of fuel and air. On the other hand, the stagnation plane imposes a certain strain rate on the flow field, which is relevant to various porous burner configurations. Therefore, the focus of this work is the study of combustion in a porous burner with a stagnation plane. An experiment is conducted with packing bed of spheres where a flame can be stabilized against a stagnation plane. The equivalence ratio and the strain rate are controlled by the flows of air and fuel and the distance between the injector and the stagnation plane. The flame position is approximately determined by the temperature field measured by thermocouples. In addition, it is performed a simplified numerical analysis of the problem in which one can see the effect of the strain rate on the stability of flames in porous burners. The results show that it is possible to stabilize flames within the porous medium with stagnation plane, however, it has not been possible to assign a temperature increase due to the increased strain rate.

O interesse no desenvolvimento de sistemas eficientes de combustão para reduzir a poluição ambiental e aumentar a eficiência de queima tem chamado a atenção para a combustão em meios porosos inertes. A recirculação de calor, induzida pela matriz sólida a partir dos produtos quentes para os reagentes frios, aumenta a temperatura da chama melhorando a sua estabilidade e permitindo a utilização de combustíveis com baixo poder calorífico. Um estudo teórico recente mostra que uma chama estabilizada por um plano de estagnação imersa em um meio poroso pode, sob certas condições, estender os limites de inflamabilidade de uma mistura de ar e combustível. Por outro lado, o plano de estagnação é um problema que simula o efeito da taxa de deformação do escoamento sobre a estabilidade da chama, o que é relevante para várias configurações de queimador poroso. Portanto, o foco deste trabalho é o estudo da combustão em um queimador poroso com um plano de estagnação. Um experimento é conduzido com empacotamento de esferas, onde uma chama pode ser estabilizada por plano de estagnação devido a um anteparo. A razão de equivalência e a taxa de deformação são controladas pelos fluxos de ar e de combustível e da distância entre injetor e anteparo. A posição da chama é aproximadamente determinada pelo campo de temperaturas medidas por termopares. Complementarmente é realizada uma análise numérica simplificada do problema na qual se pode verificar o efeito da taxa de deformação sobre a estabilidade de chamas em queimadores porosos. Os resultados mostram que é possível estabilizar chamas no interior do meio poroso com plano de estagnação, porém, não foi possível atribuir um aumento de temperatura devido ao aumento da taxa de deformação. / The interest in developing efficient combustion systems to reduce environmental pollution and increase the burning efficiency has called attention to the combustion in inert porous media. The heat recirculation, induced by the solid matrix, from the hot products to the incoming cold reactants, increases the flame temperature and improves its stability, allowing for the use of fuels with low heat content. A recent study shows theoretically that a flame stabilized by a stagnation plane immersed in a porous medium may, under certain conditions, to extend the flammability limits of a mixture of fuel and air. On the other hand, the stagnation plane imposes a certain strain rate on the flow field, which is relevant to various porous burner configurations. Therefore, the focus of this work is the study of combustion in a porous burner with a stagnation plane. An experiment is conducted with packing bed of spheres where a flame can be stabilized against a stagnation plane. The equivalence ratio and the strain rate are controlled by the flows of air and fuel and the distance between the injector and the stagnation plane. The flame position is approximately determined by the temperature field measured by thermocouples. In addition, it is performed a simplified numerical analysis of the problem in which one can see the effect of the strain rate on the stability of flames in porous burners. The results show that it is possible to stabilize flames within the porous medium with stagnation plane, however, it has not been possible to assign a temperature increase due to the increased strain rate.

Considering the importance of combustion characteristics in combustion applications including spark ignition engines and gas turbines, both laminar and turbulent burning velocities were measured for gasoline related fuels. The first part of the present work focused on the measurements of laminar burning velocities of Fuels for Advanced Combustion Engines (FACE) gasolines and their surrogates using a spherical constant volume combustion chamber (CVCC) that can provide high-pressure high-temperature (HPHT) combustion mode up to 0.6 MPa, 395 K, and the equivalence ratios ranging 0.7-1.6. The data reduction was based on the linear and nonlinear extrapolation models considering flame stretch effect. The effect of flame instability was investigated based on critical Peclet and Karlovitz, and Markstein numbers. The sensitivity of the laminar burning velocity of the aforementioned fuels to various fuel additives being knows as octane boosters and gasoline extenders including alcohols, olfins, and SuperButol was investigated. This part of the study was further extended by examining exhaust gas re-circulation effect. Tertiary mixtures of toluene primary reference fuel (TPRF) were shown to successfully emulate the laminar burning characteristics of FACE gasolines associated with different RONs under various experimental conditions. A noticeable enhancement of laminar burning velocities was observed for blends with high ethanol content (vol ≥ 45 %). However, such enhancement effect diminished as the pressure increased. The reduction of laminar burning velocity cause by real EGR showed insensitivity to the variation of the equivalence ratio. The second part focused on turbulent burning velocities of FACE-C gasoline and its surrogates subjected to a wide range of turbulence intensities measured in a fan-stirred CVCC dedicated to turbulent combustion up to initial pressure of 1.0 MP. A Mie scattering imaging technique was applied revealing the mutual flame-turbulence interaction. Furthermore, considerable efforts were made towards designing and commissioning a new optically-accessible fan-stirred HPHT combustion vessel. A time-resolved stereoscopic particle image velocimetry (TR-PIV) technique was applied for the characterization of turbulent flow revealing homogeneous-isotropic turbulence in the central region to be utilized successfully for turbulent burning velocity measurement. Turbulent burning velocities were measured for FACE-C and TPRF surrogate fuels along with the effect of ethanol addition for a wide range of initial pressure and turbulent intensity. FACE-C gasoline was found to be more sensitive to both primarily the primary contribution of turbulence intensification and secondarily from pressure in enhancing its turbulent burning velocity. Several correlations were validated revealing a satisfactory scaling with turbulence and thermodynamic parameters. The final part focused on the turbulent burning characteristics of piloted lean methane-air jet flames subjected to a wide range of turbulence intensity by adopting TR-SPIV and OH-planar laser-induced florescence (OH-PLIF) techniques. Both of the flame front thickness and volume increased reasonably linearly as normalized turbulence intensity, u^'/ S_L^0, increased. As u^'/ S_L^0 increased, the flame front exhibited more fractalized structure and occasionally localized extinction (intermittency). Probability density functions of flame curvature exhibited a Gaussian like distribution at all u^'/ S_L^0. Two-dimensional flame surface density (2D-FSD) decreased for low and moderate u^'/ S_L^0, while it increased for high u^'/ S_L^0Turbulent burning velocity was estimated using flame area and fractal dimension methods showing a satisfactory agreement with the flamelet models by Peters and Zimont. Mean stretch factor was estimated and found to increase linearly as u^'/ S_L^0increased. Conditioned velocity statistics were obtained revealing the mutual flame-turbulence interaction.

An experimental study of sooting characteristics of laminar underventillated ethylene non-premixed flames in hot vitiated environments was performed using a modified Wolfhard-Parker co-flowing slot burner. The burner could be operated in "single mode" with a cold air/oxygen mixture as the oxidizer for the non-premixed flame or in varying degrees of "dual mode" where the products of lean premixed hydrogen/air/oxygen flames were used as the oxidizer for the non-premixed flame. Premixed flame stoichiometries of 0.3 and 0.5 were considered for the dual mode cases. Dual mode operation of the burner was intended to simulate the conditions of fuel rich pockets of gas burning in the wake of previously burned fuel/air mixture as typically found in real nonpremixed combustion devices. Dual mode operation introduced competing thermal and chemical effects on soot chemistry. Experimental conditions were chosen to match peak nonpremixed flame temperatures among the cases by varying oxidizer inert (N2) concentration to minimize the dual mode thermal effect. In addition the molecular oxygen (post premixed flame for dual mode cases) and ethylene fuel flow rates were held constant to maintain the same overall equivalence ratio from case to case. Thermocouple thermometry utilizing a rapid insertion technique and radiation corrections yielded the gas temperature field. Soot volume fractions were measured simultaneously with temperature using Thermocouple Particle Densitometry (TPD). Soot volume fraction, particle size and particle number density fields were measured using laser light scattering and extinction. Gas velocities were measured using Particle Imaging Velocimetry (PIV) on the non-premixed flame centerline by seeding the ethylene flow and calculated in the oxidizer flow stream. Porous sinters in the oxidizer slots prevented oxidizer particle seeding required for PIV measurements. In general as the degree of dual mode operation was increased (i.e. increasing stoichiometry of the premixed flames) soot volume fractions decreased, particle sizes increased and soot particle number densities decreased. This trend is suspected to be result of water vapor elevating OH concentrations near the flame front in dual mode operation reducing soot particle nucleation early in the flame by oxidizing soot precursors. The larger particle sizes measured at later stages of dual mode flames are suspected to be the result of lower competition for surface growth species for the lower particle number densities in those flames. Integrated soot volume fraction and particle number fluxes at various heights in the flame decreased with increasing degree of dual mode operation. / Master of Science

Influence of dust particles on the characteristics of premixed methane-air flames has been studied in this dissertation. Experiments are performed in a Bunsen burner type experimental set-up called Hybrid Flame Analyzer (HFA), which can be used to measure the burning velocity of gas, dust, and hybrid (gas and dust) premixed flames at constant pressure operating conditions. In the current study, analysis of particle-gas-air system of different types of dust particles (at particle size, dp = 75-90 µm) in premixed methane-air (ϕg = 0.8, 1.0 and 1.2) flames. Coal, sand, and sodium bicarbonate particles are fed along with a premixed methane-air mixture at different concentrations (λp = 0-75 g/m3) in both laminar and turbulent conditions. First, the variation of laminar burning velocity with respect to the concentration of dust particles, and type of dusts are investigated for different equivalence ratios. Second, the laminar premixed flame extinction with inert and chemical suppressant particles are studied. Third, the variation of turbulent burning velocity of these hybrid mixtures are investigated against different turbulent intensities apart from the different concentrations and types of dusts. Fourth, the radiative fraction of heat released from turbulent gas-dust premixed flames are also presented against the operating parameters considered. Combustible dust deflagration hazard is normally quantified using the deflagration index (Kst) measured using a constant volume explosion sphere, which typically is a sealed 20-liter metal sphere where a premixed mixture is ignited at the center and the progression of the resulting deflagration wave is recorded using the pressure measured at the vessel wall. It has been verified from prior studies that the quantification of the turbulence by this method is questionable and there is a need to analyze the controlling parameters of particle-gas-air premixed system accurately through a near constant pressure operated experimental platform. Thus, the main objective of this study is to analyze the influence of dust particles on premixed methane-air flames at near constant pressure conditions. The turbulent burning velocity is calculated by averaging the measured flame heights and the laminar burning velocity is calculated through the premixed cone angle measurements from several high-speed shadowgraph images obtained from the experiments. The turbulent intensity and length scale of turbulence generated by a perforated plate in the burner is quantified from the hot-wire anemometer measurements. Radiative heat flux is also measured for each of the turbulent test conditions. The outcomes from these experiments are: 1. An understanding of the variation of turbulent burning velocity of gas-dust premixed flames as a function of dust type, turbulent intensity, integral length scale, dust concentration and gas phase mixture ratio. 2. An understanding of the flame extinction characteristics and variation of laminar burning velocity of gas-dust premixed flames as a function of dust concentration and gas phase mixture ratio. 3. Quantify the radiative heat flux and radiative fraction of heat released from gas-dust turbulent premixed flames as a function of dust type, turbulent intensity, dust concentration and gas phase mixture ratio. Dust type and concentration play an important role in deciding the trend in the variation of both laminar (SL) and turbulent burning velocity (ST). Coal particles, with the release of volatile (methane), tend to increase burning velocities except for fuel rich conditions and at higher coal concentrations at larger turbulent intensities. At a higher turbulent intensity and larger concentrations, higher ST values are observed with the addition of sand. Sodium bicarbonate addition, with the release of CO2 and H2O, decreased the burning velocity at all the concentrations, turbulent intensities and equivalence ratios. Laminar flame extinction was observed with the addition of sand and sodium bicarbonate particles at conditions exceeding certain critical dust concentrations. These critical concentrations varied with the equivalence ratios of gaseous premixed flames. The turbulence modulation exhibited by particles and particle concentration is evident in these observations. The independent characteristic time scale analysis performed using the experimental data provided further insights to the results. The chemical and convective times in gas phase confirm the broadened preheat thin reaction zone regime in the current test cases, which has an effect of attenuating turbulence and thereby the resulting turbulent burning velocity. The particle time scale analysis (Stokes number) show that the effect of particles and particle concentration is to slightly enhance the turbulence and increase the turbulent burning velocity at lower concentrations. However, the time scale analysis of particle vaporization (vaporization Damköhler number) indicate an increase in the vaporization rate for particles (coal and sodium bicarbonate) resulting in a decrease in their turbulent burning velocities at higher concentrations and turbulent intensities. Sodium bicarbonate has higher evaporation rate than coal at same level of turbulence and the absence of this effect for inert (sand) results in higher turbulent burning velocities at higher concentrations. An increase in the turbulent intensity increases the vaporization rate of particles. The investigation on radiative fraction of heat released by methane-air-dust turbulent premixed flames identified that, the addition of dust particles increases the radiative fraction irrespective of the dust type due to the radial and axial extension of flame. A unified approach to couple this multiple complex phenomenon of turbulence, particle interaction, particle vaporization and combustion in particle laden premixed gaseous flames is the direction for future research.

A theoretical investigation of acoustic wave interactions with turbulent premixed flames was performed. Such interactions affect the characteristic unsteadiness of combustion processes, e.g., combustion instabilities. The small perturbation method (SPM) was utilized to evaluate the scattered fields as a result of the flame-wave interaction at the instantaneous wrinkling surface of a randomly moving turbulent flame. Stochastic analysis of ensemble-averaged net acoustic energy was conducted to examine coherent and incoherent acoustic energy amplification /damping by the interaction. Net acoustic energy flux out of the flame is due to two factors: the acoustic velocity jump due to unsteady heat release from flame. The other is the flames unsteady motion. Five(5) dimensionless parameters that govern this net acoustic energy were determined: rms height and correlation length of flame front, incident wave frequency, the ratio of flames diffusion time to flame fronts correlation time, and incidence angle. The dependence of net acoustic energy upon these dimensionless parameters was illustrated and discussed by numerical simulations in case of Gaussian statistics of flame front. The laminar flame response to equivalence ratio perturbations was also examined, showing that the overall heat release response is controlled by the superposition of three disturbances: heat of reaction, flame speed, and flame area. Heat of reaction disturbances dominate the flame response at low Strouhal numbers, roughly defined as (frequency x flame length)/(axial flow velocity). All three disturbances play equal roles at Strouhal numbers of O(1). In addition, the mean equivalence ratio exerts little effect upon this transfer function at low Strouhal numbers. At O(1) Strouhal numbers, the flame response increases with decreasing values of the mean equivalence ratio.

The present thesis deals with the fundamental aspects of turbulent mixing and non-premixed combustion in the wall-jet flow, which has a close resemblance to many industrial applications. Direct numerical simulations (DNS) of turbulent wall-jets with isothermal and exothermic reactions are performed. In the computational domain, fuel and oxidizer enter separately in a nonpremixed manner and the flow is compressible, fully turbulent and subsonic. The triple “turbulence-chemistry-wall” interactions in the wall-jet flow have been addressed first by focusing on turbulent flow effects on the isothermal reaction, and then, by concentrating on heat-release effects on both turbulence and flame characteristics in the exothermic reaction. In the former, the mixing characteristics of the flow, the key statistics for combustion and the near-wall effects in the absence of thermal effects are isolated and studied. In the latter, the main target was to identify the heat-release effects on the different mixing scales of turbulence. Key statistics such as the scalar dissipation rates, time scale ratios, two-point correlations, one and two-dimensional premultiplied spectra are used to illustrate the heat release induced modifications. Finer small mixing scales were observed in the isothermal simulations and larger vortical structures formed after adding significant amounts of heat-release. A deeper insight into the heat release effects on three-dimensional mixing and reaction characteristics of the turbulent wall-jet flow has been gained by digging in different scales of DNS datasets. In particular, attention has been paid to the anisotropy levels and intermittency of the flow by investigating the probability density functions, higher order moments of velocities and reacting scalars and anisotropy invariant maps for different reacting cases. To evaluate and isolate the Damkohler number effects on the reaction zone structure from those of the heat release a comparison between two DNS cases with different Damkohler numbers but a comparable temperature rise is performed. Furthermore, the wall effects on the flame and flow characteristics, for instance, the wall heat transfer; the near-wall combustion effects on the skin-friction, the isothermal wall cooling effects on the average burning rates and the possibility of formation of the premixed mode within the non-premixed flame are addressed. The DNS datasets are also used for a priori  analysis, focused on the heat release effects on the subgrid-scale (SGS) statistics. The findings regarding the turbulence small-scale characteristics, gained through the statistical analysis of the flow have many phenomenological parallels with those concerning the SGS statistics. Finally, a DNS of turbulent reacting wall-jet at a substantially higher Reynolds number is performed in order to extend the applicability range for the conclusions of the present study and figuring out the possible differences. / <p>QC 20150225</p>

[ES] El objetivo de esta tesis es la investigación y análisis de la estructura interna de los chorros diésel reactivos y el efecto de las condiciones de contorno en los parámetros asociados a la combustión. Este objetivo se consigue por medio de la simulación numérica del chorro con modelos de turbulencia RANS y LES usando un modelo de combustión avanzado basado en el concepto flamelet. Para este estudio, se aplica una aproximación simplificada de las flamelets de difusión, conocidas en la literatura como Flamelets de Difusión Aproximadas (ADF en inglés), como fundamento del modelo de combustión. En una primera etapa, el modelo se valida con combustibles de diferente complejidad química en regímenes estacionarios y transitorios para el conjunto de posibles velocidades de deformación. Una vez se confirma su idoneidad para condiciones encontradas en chorros diésel, se aplica a la simulación del chorro A del Engine Combustion Network (ECN), representativo de chorros diésel. Para proporcionar un cuadro completo de los fenómenos subyacentes, la combustión se analiza inicialmente para condiciones homogéneas y llamas laminares para las distintas condiciones de contorno de este experimento. Después este análisis se complementa con la simulación de diferentes mecanismos químicos para determinar cómo las características del encendido predichas por el esquema de oxidación afectan a la propagación de llama. Los resultados obtenidos en esta etapa se enlazan con el análisis del chorro turbulento en el contexto de simulaciones RANS y LES para describir cómo el fenómeno de la combustión se modifica con los diferentes niveles de complejidad física. La estructura del chorro turbulento se describe profundamente para las distintas condiciones de contorno y mecanismos químicos en términos de mezcla y escalares reactivos para las fases temporales y las regiones espaciales de la llama. La satisfactoria concordancia con los resultados experimentales muestran que el concepto flamelet, y más particularmente el modelo ADF, es adecuado para las simulaciones de chorros diésel. / [CAT] L'objectiu d'esta tesi és la investigació i anàlisi de l'estructura interna dels dolls dièsel reactius i l'efecte de les condicions de contorn en els paràmetres associats a la combustió. Este objectiu s'aconsegueix per mitjà de la simulació numèrica del doll amb models de turbulència RANS i LES usant un model de combustió avançat basat en el concepte flamelet. Per a este estudi, s'aplica una aproximació simplificada de les flamelets de difusió, conegudes a la literatura com Flamelets de Difusió Aproximades (ADF en anglés), com a fonament del model de combustió. En una primera etapa, el model es valida amb combustibles de diferent complexitat química en règims estacionaris i transitoris per al conjunt de possibles velocitats de deformació. Una vegada es confirma la seua idoneïtat per a condicions trobades en dolls dièsel, s'aplica a la simulació del doll A del Engine Combustion Network (ECN), representatiu de dolls dièsel. Per a proporcionar un cuadre complet dels fenòmens subjacents, la combustió s'analitza inicialment per a condicions homogènies i flames laminars per a les distintes condicions de contorn d'aquest experiment. Després esta anàlisi es complementa amb la simulació de diferents mecanismes químics per a determinar com les característiques de l'encesa predites per l'esquema d'oxidació afecten la propagació de flama. Els resultats obtinguts en esta etapa s'enllacen amb l'anàlisi del doll turbulent en el context de simulacions RANS i LES per a descriure com el fenomen de la combustió es modifica amb els diferents nivells de complexitat física. L'estructura del doll turbulent es descriu profundament per a les distintes condicions de contorn i mecanismes químics en termes de mescla i escalars reactius per a les fases temporals i les regions espacials de la flama. La satisfactòria concordança amb els resultats experimentals mostren que el concepte flamelet, i més particularment el model ADF, és adequat per a les simulacions de dolls dièsel. / [EN] The objective of this thesis is the investigation and analysis of the internal structure of diesel-like reacting sprays and the effect of boundary conditions on combustion related parameters. This objective is achieved by means of the numerical simulation of the spray with RANS and LES turbulence models using an advanced combustion model based on the flamelet concept. For this study, a simplified approach for diffusion flamelets, known in the literature as Approximated Diffusion Flamelet (ADF), is applied as the basis of the combustion model. In a first step, this model is validated for fuels with different chemical complexity in steady and transient regimes for the whole set of possible strain rates. Once its suitability is confirmed for conditions found in diesel sprays, it is applied to the simulation of spray A from the Engine Combustion Network (ECN), representative of diesel-like sprays. In order to provide a complete picture of the underlying phenomena, combustion is initially analysed in homogeneous conditions and laminar flames for the different boundary conditions of this experiment. Later, this analysis is complemented with the simulation of different chemical mechanisms in order to determine how the ignition characteristics predicted by the oxidation scheme affect to the flame propagation. The results obtained at this stage are connected with the analysis of the turbulent spray in the context of RANS and LES simulations as a way to track how combustion phenomenon is modified at the different levels of physical complexity. The turbulent spray structure is thoroughly described for the different boundary conditions and chemical schemes in terms of mixing and reactive variables for both temporal phases and spatial flame regions. The satisfactory agreement with experimental results shows that the flamelet concept, and more particularly the ADF model, is suitable for diesel-like sprays simulations. / Pérez Sánchez, EJ. (2019). Application of a flamelet-based combustion model to diesel-like reacting sprays [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/117316 / TESIS