>Magister Scientiae - MSc / We have used the Spitzer Survey of Stellar Structure in Galaxies (S⁴G) as a representative sample of the local universe (total of 2352 galaxies in S⁴G) to make a catalog of offset disk barred galaxies. Using the combined variation of the position angle and the ellipticity (provided by ellipse fit) and also through visual inspection, we have been able to identify all offset structures in S⁴G. While primary bars are present in 2=3 of the disk galaxies in the visible universe, offset bars have a much lower fraction. Of the ̴ 1500 (3.6µm images) disk galaxies available in S⁴G, we classified only 49 as offset barred disk galaxies. We have determined basic properties (bar to total luminosity ratio, bar length, disk scale-length and bars of offset bars shape) using GALFIT, a widely used galaxy decomposition software package. Our main conclusion is that all the offset bars are boxy, independent of their offset from the galaxy center, or the mass of the host galaxy. Additionally we find that, the early type offset bars seem to be more boxy than the late types. The comparison of our offset sample with two other samples, respectively, low mass and high mass normal barred galaxies ("normal" for bars located at the photometric center of the host galaxy), reveals them to be at an intermediate position between the two normal samples. The bar length, disk scale-length and bar to total luminosity ratio are on average larger than the low mass normal and smaller than high mass normal barred galaxies. We have found, overall, a tighter correlation between the disk and bar properties for offset bars in comparison to the two normal samples. Our explanation is that, although the offset has no visible impact on the global shape of the bars, the process responsible for these disturbances seems to affect the star formation rate such that their disk and bars are on average more active than the normal barred galaxies in the same mass range, but not enough to surpass normal barred galaxies with much higher mass.

Abstract In this thesis, iterative detection and estimation algorithms for digital communications systems in the presence of parametric uncertainty are explored and further developed. In particular, variational methods, which have been extensively applied in other research fields such as artificial intelligence and machine learning, are introduced and systematically used in deriving approximations to the optimal receivers in various channel conditions. The key idea behind the variational methods is to transform the problem of interest into an optimization problem via an introduction of extra degrees of freedom known as variational parameters. This is done so that, for fixed values of the free parameters, the transformed problem has a simple solution, solving approximately the original problem. The thesis contributes to the state of the art of advanced receiver design in a number of ways. These include the development of new theoretical and conceptual viewpoints of iterative turbo-processing receivers as well as a new set of practical joint estimation and detection algorithms. Central to the theoretical studies is to show that many of the known low-complexity turbo receivers, such as linear minimum mean square error (MMSE) soft-input soft-output (SISO) equalizers and demodulators that are based on the Bayesian expectation-maximization (BEM) algorithm, can be formulated as solutions to the variational optimization problem. This new approach not only provides new insights into the current designs and structural properties of the relevant receivers, but also suggests some improvements on them. In addition, SISO detection in multipath fading channels is considered with the aim of obtaining a new class of low-complexity adaptive SISOs. As a result, a novel, unified method is proposed and applied in order to derive recursive versions of the classical Baum-Welch algorithm and its Bayesian counterpart, referred to as the BEM algorithm. These formulations are shown to yield computationally attractive soft decision-directed (SDD) channel estimators for both deterministic and Rayleigh fading intersymbol interference (ISI) channels. Next, by modeling the multipath fading channel as a complex bandpass autoregressive (AR) process, it is shown that the statistical parameters of radio channels, such as frequency offset, Doppler spread, and power-delay profile, can be conveniently extracted from the estimated AR parameters which, in turn, may be conveniently derived via an EM algorithm. Such a joint estimator for all relevant radio channel parameters has a number of virtues, particularly its capability to perform equally well in a variety of channel conditions. Lastly, adaptive iterative detection in the presence of phase uncertainty is investigated. As a result, novel iterative joint Bayesian estimation and symbol a posteriori probability (APP) computation algorithms, based on the variational Bayesian method, are proposed for both constant-phase channel models and dynamic phase models, and their performance is evaluated via computer simulations.

Abstract In gravure offset printing, ink is transferred with the help of an offset material from a patterned gravure plate to a substrate. This thesis is concerned with the study and further development of this printing process for electronics; on alumina, glass and polymers. The work has been divided into five parts. In the first section, the printing process is described. The second section describes the composition of the inks for gravure offset printing and the resulting ink properties. It also presents the ink transfer mechanism; the model that explains how the ink is transferred between an offset material and a substrate. The third chapter details the printing process explained by a solvent absorption mechanism. The forth chapter describes the firing/curing of printed samples and their properties. The last chapter describes applications of the method. The inks used to produce conductors on ceramics (ceramic inks) and conductors on polymers (polymer inks) contain silver particles, and were under development for gravure offset printing. The major achieved properties were the high ink pickup to the offset blanket and high transfer percentage to the substrate. 100% ink transfer from blanket to substrate for ceramic inks and almost 100% ink transfer for polymer inks was obtained. The printing of ceramic inks was able to produce 8 μm of relatively thick, 300 μm wide lines with < 10 mΩ/sq. resistance. The minimum line width for conducting lines was 35 μm, with one printing. Multi printing was applied producing as many as 10 times wet-on-wet multiprinted lines with 100 % ink transfer from blanket to substrate resulting in a square resistance of 1mΩ/sq. Polymer inks were able produce a square resistance of 20 mΩ/sq. for 300 μm wide lines after curing at 140 °C for about 15 min, and the minimum width was down to 70 μm. In the optimised manufacturing process, the delay time on the blanket was reduced to 3 s. In addition to ultra-fine-line manufacturing of conductors, the method enables the manufacture of special structures e.g. laser-solder contact pads with 28/28 μm lines/spaces resolution. With industrial printing equipment it is possible to produce 100 m2/h with the demonstrated printing properties.

Abstract The thesis is concerned with the development of gravure-offset-printing and low temperature co-fired ceramic (LTCC) technologies for the miniaturisation of electronic devices and components. The development work has been verified by several applications. Several aspects of gravure-offset-printing have to be optimised in order to make it suitable for fine-line printing and these have been addressed in the study with a focus on the printing inks and plates. Gravure-offset-printing inks were developed from commercial thick-film pastes. The effects of different ink characteristics on some properties of conductor lines, such as line width and resistivity, were studied. The dependence of the conductor lines on the quality of the engravings in the printing plates was also studied. The narrowest line widths obtained were about 30 μm with an accuracy of ±5 μm. Various LTCC compositions and processing steps involved in the production of integrated electronic devices, and the properties of several fabricated devices are discussed. The devices include inductors, band-pass filters and resistors for the 1–2 GHz frequency range. Miniaturisation has been the main focus of attention. For example, the integration of high-permittivity tapes in addition to low-permittivity tapes has made the miniaturisation of filter structures possible. Compatibility between these tapes during firing was found to be good. LTCC technology was further developed by adapting a modified LTCC-on-metal (LTCC-M) approach. A traditional way of guiding heat away from a component is to place a heat-sink under the component and utilise thermal vias and solder balls. In this study high- and low-permittivity tapes were attached directly on a heat-sink. Different heat-sink options were evaluated and the best performance was achieved with an AlN heat-sink which was deposited by screen-printing a Au layer on it. High-power chips were attached directly on the heat-sink through cavities in the LTCC tapes. This approach also restricted the shrinkage of the LTCC tapes. The fabricated test structures and components proved the viability of the approach although the compatibility between the pastes and tapes was not optimal.

In many instances the properties of a network are obstructed by an intervening network, which is required when performing measurements of the network. These intervening networks are often in the form of a mode transformer and are, in the general sense, referred to as error networks. A new analysis mechanism is developed by applying a de-embedding method that was identified as being robust. The analysis was subsequently implemented in a numerical computational software package. The analysis mechanism can then be applied to perform the characterisation of error networks. The performance of the analysis mechanism is verified using an ideal lumped-element network. The limitations of the mechanism are identified and possible ways of addressing these limitations are given. The mechanism is successfully applied to the characterisation of three different microwave networks. / Dissertation (MEng)--University of Pretoria, 2013. / gm2014 / Electrical, Electronic and Computer Engineering / unrestricted

No description available.

In March 2011, the European Commission submitted a proposal for a Council Directive on an optional common consolidated corporate tax base (CCCTB). If this proposed CCCTB system comes into force, taxes calculated under the currently existing system of separate accounting might be replaced by a system of group consolidation and formulary apportionment. Then, multinational groups (MNGs) would face the decision as to whether to opt for the CCCTB system. Prior research focuses mainly on the differences in economic behaviour under both systems in general. By contrast, we study the conditions under which one or the other tax system is preferable from the perspective of an MNG, with a particular focus on loss-offsets. We identify four effects that determine the decision of an MNG: the tax-utilization of losses, the allocation of the tax base, the dividend and intragroup interest taxation. We find mixed results, e.g., that the CCCTB system proves advantageous for increasing loss/profit streams (e.g. from start-ups or R&D projects) of the individual group entities, whereas the system of separate accounting is beneficial for decreasing profit/loss streams (e.g. caused by a decrease in return from a mature product). The results of our analysis are helpful for MNGs facing the decision as to whether to opt for the CCCTB system and can also support legislators and politicians in the EU but also in other regions in their tax reform discussions. (authors' abstract)

This licentiate thesis comprises two complementary studiesdealing with the sheet-fed offset printing of paper. The firststudy addresses the further development of a practical methodto acoustically monitor and analyse the film splitting ofoffset inks. This method was tested on laboratory printingequipment, specifically monitoring the continuous ink splittingin the nip of an IGT ink distribution unit and the short-timeink splitting in the inked print disc-paper nip of the printingunit of an ISIT instrument. The study verified that the inksplitting component of the acoustic signal contributes to thehigher frequency range (10-20 kHz) of the audible spectrum, andcan thus be separated from the lower frequency machine noise.Furthermore, the film splitting component is sensitive tochanges in the ink and printing conditions, thus enabling itsuse in probing the fundamental mechanisms occurring during inktransfer and also suggesting its applicability fornon-intrusive monitoring of industrial printing presses. Anincrease in film thickness during ink distribution correspondsto an increased acoustic power, with the exception of very lowink amounts, which give reduced acoustic emission due to alubricating effect. The effect of the presence of fountainsolution was simulated by adding emulsion-forming, butnon-evaporative, ethylene glycol. This produces an increase inacoustic power at low amounts, due to resistance to glycol dropdeformation, followed by a decrease at higher amounts owing toexcess glycol lining the rolls. During test printing on paper,increasing ink amounts also display an increased acousticresponse. The second study further developed a theoretical model toexplain and predict the evolution of ink tack in terms of inksetting directly after offset printing on coated paper. Asmeasured by the ISIT, the tack of the printed ink rises duringshorter time periods, attains a maximum, and then falls atlonger times. The proposed model described how the ink tack,characterised by the impulse during disc pull-off, dependsdynamically on the viscoelastic properties of the ink, thecontact with paper and disc, and the flow geometry. The inksetting was modelled as a diffusion-limited transport of theoil vehicle through the ink film and into the pores of thecoated paper. The coupling of the tack and setting models,compared to the ISIT experimental measurements, then provided adiffusion coeffcient for ink setting during the tack riseperiod. This coeffcient decreases with time, and increasinglyrapidly with decreasing ink amounts due to theconcentration-dependent diffusion. For an accurate descriptionthe elasticity and adhesion effects also have to be considered,at least for explaining the tack fall period.

Indiana University-Purdue University Indianapolis (IUPUI) / The nanotechnology materials have been used for high sensitivity sensing devices due to their ability to alter their properties in response to the environmental parameters such as temperature, pressure, gas, electromagnetic, and chemicals. The features of employing nanoparticles on top of graphene thin film have driven the hypothesis of achieving high sensing nanotechnology devices. This study demonstrates a novel approach for designing a low noise nanoparticle based gas sensing device with internet of things (IoT) capability. The system is capable of minimizing cross-talk between multiple channels of amplifiers arranged on one chip using guard rings. Graphene mono-layer is utilized as sensing material with the sensitivity catalyzed by addition of gold nano-particles on its surface. The signal from the sensing unit is received by an offset cancellation amplifying system using a system on chip (SoC) approach. IoT capability of the sensing device is developed using FRDM K64f micro-controller board which sends messages on IoT platform when a gas is sensed. The message is received by an application created and sent as an email or message to the user. This study details the mathematical models of the graphene based gas sensing devices, and the interface circuitry that drives the differential potentials, resulting from the sensing unit. The study presents the simulation and practical model of the device, detailing the design approach of the processing unit within the SoC system and wireless implementation of it. The sensing device was capable of sensing gas concentration from 5% to 100% using both the resistive and capacitive based models. The I-V characteristics of the FET sensing device was in agreeable with the other models. The SoC processing unit was designed using cadence tools, and simulation results showed very high CMRR that enable the amplifier to sense a very low signal received from the gas sensors. The cross talk noise was reduced by surrounding guard rings around the amplifier circuits. The layout was accomplished with 45nm technology and simulation showed an offset voltage of 17μV.

No description available.