This thesis describes an experimental investigation of optical frequency conversion in isotropic semiconductor waveguides by use of several phase-matching approaches. Efficient, type I second harmonic generation of femtosecond pulses is reported in birefringently-phase-matched GaAs/Alox waveguides pumped at 2.01 μm. Practical second harmonic average powers of up to ~ 650 μW are obtained, for an average launched pump power of ~ 5 mW. This corresponds to a waveguide conversion efficiency of ~ 20 % and a normalized conversion efficiency of greater than 1000 % W−1cm−2. Pump depletion of more than 80 % is recorded. Second harmonic generation by type I, third order quasi-phase-matching in a GaAs- AlAs superlattice waveguide is reported for fundamental wavelengths from ~1480 to 1520 nm. Quasi-phase-matching is achieved through modulation of the nonlinear coefficient χ[sub](zxy)(2), which is realised by periodically tuning the superlattice bandgap. An average output power of ~25 nW is obtained for a launched pump power of < 2.3 mW. Type I second harmonic generation by use of first order quasi-phase-matching in a GaAs/AlAs symmetric superlattice waveguide is also reported, with femtosecond fundamental pulses at 1.55 μm. A periodic spatial modulation of the bulk-like second- order susceptibility χ[sub](zxy)(2) is realized using quantum well intermixing by As+ ion implantation. A practical second harmonic average power of ~1.5 μW is detected, for a coupled pump power of ~11 mW. Second harmonic generation through modal-phase-matching in GaAs/AlGaAs semiconductor waveguides is reported. Using femtosecond pulses, both type I and type II second harmonic conversion is demonstrated for fundamental wavelengths near 1.55 μm. An average second harmonic power of ~10.3 μW is collected at the waveguide output for a coupled pump power of < 20 mW. For a complete characterisation, the optical loss is measured in these nonlinear GaAs- based waveguides over the spectral range 1.3-2.1 μm in the infrared, by deploying a femtosecond scattering technique. Typical losses of ~5-10 dB/cm are measured for the best of the waveguides, while a systematic intensity and wavelength dependent study revealed the contribution of Rayleigh scattering and two photon absorption in the overall transmission loss.

Material and structure engineering are increasingly employed in active optical media,in this context defined as media capable of providing laser or/and optical parametric gain. For laser materials, the main aim of the engineering is to tailor the absorption and emission cross sections in order to optimise the laser performance. At the same time, the engineering also results in a collateral modification of the material’s nonlinear response. In the first part of this work, the nonlinear index of refraction is characterised for two crystallographic forms of laser-ion doped and undoped double-tungstate crystals. These laser crystals have broad gain bandwidths, in particular when doped with Yb3+. As shown in this work, the crystals also have large Kerr nonlinearities, where the values vary significantly for different chemical compositions of the crystals. The combination of a broad gain bandwidthand a high Kerr nonlinearity makes the laser-ion doped double tungstates excellent candidates to employ for the generation of ultrashort laser pulses by Kerr-lens modelocking. The second part of the work relates to the applications of engineered second-order nonlinear media, which here in particular are periodically-poled KTiOPO4 crystals. Periodic structure engineering of second-order nonlinear crystals on a submicrometre scale opens up for the realisation of novel nonlinear devices. By the use of quasi-phase matching in these structures, it is possible to efficiently downconvert a pump wave into two counterpropagating parametric waves, which leads to a device called a mirrorless optical parametric oscillator. The nonlinear response in these engineered submicrometre structures is such that the parametric wave that propagates in the opposite direction of the pump automatically has a narrow bandwidth, whereas the parametric wave that propagates with the pump essentially is a frequency-shifted replica of the pump wave. The unusual spectral properties andthe tunabilities of mirrorless optical parametric oscillators are investigated. / QC 20120330

<p>This thesis discusses a new scheme for generating radiation in the mid infrared spectral region, especially the 3.5-5 µm range. The scheme uses established Nd³⁺-lasers at 1.06 µm and down conversion in nonlinear optical crystals. The down conversion is made by two optical parametric oscillators (OPO) in series. The second OPO is a classical OPO using a zink germanium phosphide (ZGP) crystal. ZGP is the best nonlinear material available for the 4-8 µm spectral range, but it is absorbing below 2 µm. The new development presented in this thesis is the OPO used to convert the 1.06 µm laser radiation to a suitable OPO pump near 2 µm.</p><p>The OPO uses a type I quasi phase-matched crystal, which accesses high nonlinearities and avoids walk-off. The problem with type I OPOs close to degeneracy is the broad bandwidth of the generated radiation, which reduces the efficiency of a second OPO. This has been solved with a spectrally selective cavity using a volume Bragg grating output coupler. Unlike other bandwidth limiting schemes this introduces no intracavity losses and thus efficient OPO operation is achievable.</p><p>Narrow linewidth (~0.5 nm) OPO operation has been achieved with periodically poled LiNbO₃ (PPLN) and periodically poled KTiOPO4 (PPKTP) while locking the signal wavelength at 2008 nm and simultaneously generating an idler at 2264 nm. A high average power PPLN OPO with 36 % conversion efficiency and 47 % slope efficiency is reported. Operation very close to degeneracy at 2128 nm with the narrowband signal and idler peaks separated by 0.6 nm was demonstrated in a PPKTP OPO. Both the signal at 2008 nm and the combined signal and idler around 2128 nm from the PPKTP OPOs have been used to show efficient pumping of a ZGP OPO. The maximum conversion efficiency from 1 µm to the mid-IR demonstrated is 7 % with a slope efficiency of 10 %. This is not quite as high as what has been presented by other authors, but the experiments reported here have not shown the optimum efficiency of the new scheme. Relatively simple improvements are expected to give a significant increase in conversion efficiency.</p>

This thesis discusses a new scheme for generating radiation in the mid infrared spectral region, especially the 3.5-5 µm range. The scheme uses established Nd3+-lasers at 1.06 µm and down conversion in nonlinear optical crystals. The down conversion is made by two optical parametric oscillators (OPO) in series. The second OPO is a classical OPO using a zink germanium phosphide (ZGP) crystal. ZGP is the best nonlinear material available for the 4-8 µm spectral range, but it is absorbing below 2 µm. The new development presented in this thesis is the OPO used to convert the 1.06 µm laser radiation to a suitable OPO pump near 2 µm. The OPO uses a type I quasi phase-matched crystal, which accesses high nonlinearities and avoids walk-off. The problem with type I OPOs close to degeneracy is the broad bandwidth of the generated radiation, which reduces the efficiency of a second OPO. This has been solved with a spectrally selective cavity using a volume Bragg grating output coupler. Unlike other bandwidth limiting schemes this introduces no intracavity losses and thus efficient OPO operation is achievable. Narrow linewidth (~0.5 nm) OPO operation has been achieved with periodically poled LiNbO3 (PPLN) and periodically poled KTiOPO4 (PPKTP) while locking the signal wavelength at 2008 nm and simultaneously generating an idler at 2264 nm. A high average power PPLN OPO with 36 % conversion efficiency and 47 % slope efficiency is reported. Operation very close to degeneracy at 2128 nm with the narrowband signal and idler peaks separated by 0.6 nm was demonstrated in a PPKTP OPO. Both the signal at 2008 nm and the combined signal and idler around 2128 nm from the PPKTP OPOs have been used to show efficient pumping of a ZGP OPO. The maximum conversion efficiency from 1 µm to the mid-IR demonstrated is 7 % with a slope efficiency of 10 %. This is not quite as high as what has been presented by other authors, but the experiments reported here have not shown the optimum efficiency of the new scheme. Relatively simple improvements are expected to give a significant increase in conversion efficiency. / QC 20101108

In this thesis the control of ultrafast (10⁻¹³ s) optical pulses used for metrological applications has been investigated. Two different measurement set-ups have been considered, both based around the `pump-probe' technique, where an optical pulse is divided into two parts, one to `pump' or excite a physical system of interest, the other to `probe' or measure the outcome. In both cases the measurement uses electro-optic sampling (EOS), where an electric field is measured by detecting changes in the optical probe pulse polarisation after interaction with the field. In the first study, a method for wavelength metrology in the terahertz (THz) region has been demonstrated by producing an optical pulse shaper and genetic algorithm to control pump pulses and so indirectly influence the THz spectra they generate. In the second study an OPO (optical parametric oscillator) has been developed to provide ultrafast optical pulses for the generation of < 100 fs electrical pulses for metrology using quantum interference control (QUIC). QUIC electrical signals have been demonstrated successfully by charge accumulation measurements and the QUIC electrical pulse temporally measured using EOS, though the low signal levels due to power restrictions mean the QUIC electrical pulse is unsuitable for metrology at this time. Finally, a portable optical pulse measurement device based around frequency-resolved optical gating (FROG) has been designed, built and tested. This has been shown to be capable of retrieving amplitude and phase information in both the temporal and spectral domains for optical pulses as short as 20 fs duration. The ability to characterise shaped pulses also has been demonstrated successfully, with the requirements for full automation identified.

Optical parametric oscillators (OPOs) and optical parametricamplifiers (OPAs) constitute a class of optical frequencyconverting devices that have many possible applications, e.g.in range finding, molecular spectroscopy and medicine. They canconvert the frequency of the incident pump field with highefficiency, and generate two waves at new frequencies that willbe continuously tuneable over a wide spectral range. Virtuallyany wavelengths within the transparency region of the nonlinearmaterial can be generated if the material can bequasi-phasematched (QPM). In addition, QPM gives thepossibility to utilise the largest nonlinear tensor element ofthe material and allows walk-off free interaction between thewaves. The aims of this thesis have been to investigate thepossibility to use QPM KTiOPO4crystals as nonlinear material in nanosecond OPOsand OPAs operating at room-temperature, and to explore theadvantages and shortcomings of these devices. The technique ofelectric field poling has been employed to implement the QPMstructure in flux grown KTiOPO4(KTP). The main conclusion is that periodically poled KTP (PPKTP)is a suitable material to use in nanosecond OPOs and OPAs. Thematerial properties that foremost make KTP into an attractivenonlinear material are: The large value of the nonlinearcoefficient d33, the high resistance to optically inducedbreakdown, the low susceptibility to grey-track formation, theinsensitivity to the photorefractive effect, the widetransparency and the low coercive field. The thesis shows that it is possible to pole large volumesof KTP with a high quality of the QPM structure. Highlyefficient nanosecond OPOs have been constructed during thisproject. Maximum conversion efficiencies have reached 45 % inthe case of a singly resonant OPO (SRO) built around a 3 mmthick PPKTP crystal. Total pulse energies for both the signal(1.72 µm) and the idler (2.8 µm) of up to 18 mJ wasreached and an average output power of 2 W was obtained forthis sample. However, up to 24 W was produced in a doublyresonant OPO operating close to degeneracy. The efficiencyreached 48 % for that case. Truly continuous and very widespectral tuning has also been demonstrated, as well as a narrowbandwidth OPO operating on one single longitudinal mode. <b>Keywords:</b>optical parametric oscillators, opticalparametric amplifiers, quasi-phasematching, KTiOPO4, nonlinear optics, frequency conversion, periodicelectric field poling, ferroelectrics, high-order secondharmonic generation, electro-optic effect.

<p>Optical parametric oscillators (OPOs) and optical parametricamplifiers (OPAs) constitute a class of optical frequencyconverting devices that have many possible applications, e.g.in range finding, molecular spectroscopy and medicine. They canconvert the frequency of the incident pump field with highefficiency, and generate two waves at new frequencies that willbe continuously tuneable over a wide spectral range. Virtuallyany wavelengths within the transparency region of the nonlinearmaterial can be generated if the material can bequasi-phasematched (QPM). In addition, QPM gives thepossibility to utilise the largest nonlinear tensor element ofthe material and allows walk-off free interaction between thewaves.</p><p>The aims of this thesis have been to investigate thepossibility to use QPM KTiOPO₄crystals as nonlinear material in nanosecond OPOsand OPAs operating at room-temperature, and to explore theadvantages and shortcomings of these devices. The technique ofelectric field poling has been employed to implement the QPMstructure in flux grown KTiOPO₄(KTP).</p><p>The main conclusion is that periodically poled KTP (PPKTP)is a suitable material to use in nanosecond OPOs and OPAs. Thematerial properties that foremost make KTP into an attractivenonlinear material are: The large value of the nonlinearcoefficient d₃₃, the high resistance to optically inducedbreakdown, the low susceptibility to grey-track formation, theinsensitivity to the photorefractive effect, the widetransparency and the low coercive field.</p><p>The thesis shows that it is possible to pole large volumesof KTP with a high quality of the QPM structure. Highlyefficient nanosecond OPOs have been constructed during thisproject. Maximum conversion efficiencies have reached 45 % inthe case of a singly resonant OPO (SRO) built around a 3 mmthick PPKTP crystal. Total pulse energies for both the signal(1.72 µm) and the idler (2.8 µm) of up to 18 mJ wasreached and an average output power of 2 W was obtained forthis sample. However, up to 24 W was produced in a doublyresonant OPO operating close to degeneracy. The efficiencyreached 48 % for that case. Truly continuous and very widespectral tuning has also been demonstrated, as well as a narrowbandwidth OPO operating on one single longitudinal mode.</p><p><b>Keywords:</b>optical parametric oscillators, opticalparametric amplifiers, quasi-phasematching, KTiOPO₄, nonlinear optics, frequency conversion, periodicelectric field poling, ferroelectrics, high-order secondharmonic generation, electro-optic effect.</p>

Šioje disertacijoje teoriškai ir eksperimentiškai tiriamas erdvinių šviesos darinių formavimasis didelės apertūros monolitiniuose parametriniuose šviesos generatoriuose (PŠG), nagrinėjamos fotoninių kristalų (FK) rezonatorių erdvinės dispersijos savybės. Darbas susideda iš įvado, literatūros apžvalgos ir dviejų pagrindinių dalių. Pirmoje dalyje aprašomas PŠG tyrimas didelės apertūros (5x5x1,5 mm) BBO I fazinio sinchronizmo tipo kristalo monolitiniame mini rezonatoriuje. Generatoriui kaupinti naudojami antros Nd:IAG lazerio harmonikos (532 nm) 13 ns trukmės ir 7-15 mJ energijos impulsai. Erdviniai šviesos dariniai registruojami artimajame ir tolimajame laukuose. Eksperimentiškai parodoma ir teoriškai interpretuojama, kad tokio rezonatoriaus emisija gali būti kūginė ir daugiakūgė, o signalinės ir skirtuminės bangų kryptys gali būti valdomos keičiant kampą tarp rezonatoriaus optinės ašies ir kaupinimo pluošto. Taip pat parodoma, kad dryžių erdvinio šviesos darinio formavimasis gali būti pasiekiamas injektuojant pagrindinio dažnio užkrato signalą. Antrojoje disertacijos dalyje pristatomi ir tiriami plokščiųjų veidrodžių Fabri ir Pero tipo rezonatoriai su vidine lūžio rodiklio moduliacija, atitinkančia vieną fotoninio kristalo (FK) išilginį periodą. FK rezonatoriai sukurti veidrodžių paviršiuje suformuojant 2 µm, 4 µm ir 15 µm periodinę lūžio rodiklio moduliaciją (t.y. suformuojant vienmatę arba dvimatę fazinę difrakcinę gardelę). FK rezonatorių kampinis pralaidumas matuotas... [toliau žr. visą tekstą] / This Ph.D. thesis contains experimental and theoretical analysis of nonlinear optical pattern formation in monolithic mini-cavity optical parametrical oscillators and spatial properties of linear photonic crystal resonators. The thesis consists of introduction, literature review and two chapters. In the first chapter experimental investigation of optical parametrical oscillation (OPO) in broad aperture monolithic (5x5x1.5 mm) BBO type I crystal mini-cavity is described. OPO was pumped by second harmonic (532 nm) 13 ns duration, 7 15 mJ energy pulses, of Nd:YAG laser. Optical patterns were registered in a near and far field of OPO emission. Experiments and theoretical interpretation revealed that emission of such resonator can be conical and multiconical and direction of signal and idler waves can be controlled by changing the mini-cavity orientation with respect to pump beam. It was also showed, that the stabilization of stripes (or roll) pattern can be achieved by a weak seed injection at subharmonic frequency and temporal spectrum of the stripe pattern degenerate OPO emission is 1/f – like noise spectrum . In the second chapter plane-mirror Fabry-Pérot resonators filled with a single period of photonic crystal (PhC) are introduced and analyzed. PhC resonators are realized by adding periodical 2 µm, 4 µm and 15 µm refraction index modulation on a resonator mirror surfaces (i.e. fabricating 1D or 2D phase diffraction grating). PhC resonator angular transmission measured by... [to full text]

This Ph.D. thesis contains experimental and theoretical analysis of nonlinear optical pattern formation in monolithic mini-cavity optical parametrical oscillators and spatial properties of linear photonic crystal resonators. The thesis consists of introduction, literature review and two chapters. In the first chapter experimental investigation of optical parametrical oscillation (OPO) in broad aperture monolithic (5x5x1.5 mm) BBO type I crystal mini-cavity is described. OPO was pumped by second harmonic (532 nm) 13 ns duration, 7 15 mJ energy pulses, of Nd:YAG laser. Optical patterns were registered in a near and far field of OPO emission. Experiments and theoretical interpretation revealed that emission of such resonator can be conical and multiconical and direction of signal and idler waves can be controlled by changing the mini-cavity orientation with respect to pump beam. It was also showed, that the stabilization of stripes (or roll) pattern can be achieved by a weak seed injection at subharmonic frequency and temporal spectrum of the stripe pattern degenerate OPO emission is 1/f – like noise spectrum . In the second chapter plane-mirror Fabry-Pérot resonators filled with a single period of photonic crystal (PhC) are introduced and analyzed. PhC resonators are realized by adding periodical 2 µm, 4 µm and 15 µm refraction index modulation on a resonator mirror surfaces (i.e. fabricating 1D or 2D phase diffraction grating). PhC resonator angular transmission measured by... [to full text] / Šioje disertacijoje teoriškai ir eksperimentiškai tiriamas erdvinių šviesos darinių formavimasis didelės apertūros monolitiniuose parametriniuose šviesos generatoriuose (PŠG), nagrinėjamos fotoninių kristalų (FK) rezonatorių erdvinės dispersijos savybės. Darbas susideda iš įvado, literatūros apžvalgos ir dviejų pagrindinių dalių. Pirmoje dalyje aprašomas PŠG tyrimas didelės apertūros (5x5x1,5 mm) BBO I fazinio sinchronizmo tipo kristalo monolitiniame mini rezonatoriuje. Generatoriui kaupinti naudojami antros Nd:IAG lazerio harmonikos (532 nm) 13 ns trukmės ir 7-15 mJ energijos impulsai. Erdviniai šviesos dariniai registruojami artimajame ir tolimajame laukuose. Eksperimentiškai parodoma ir teoriškai interpretuojama, kad tokio rezonatoriaus emisija gali būti kūginė ir daugiakūgė, o signalinės ir skirtuminės bangų kryptys gali būti valdomos keičiant kampą tarp rezonatoriaus optinės ašies ir kaupinimo pluošto. Taip pat parodoma, kad dryžių erdvinio šviesos darinio formavimasis gali būti pasiekiamas injektuojant pagrindinio dažnio užkrato signalą. Antrojoje disertacijos dalyje pristatomi ir tiriami plokščiųjų veidrodžių Fabri ir Pero tipo rezonatoriai su vidine lūžio rodiklio moduliacija, atitinkančia vieną fotoninio kristalo (FK) išilginį periodą. FK rezonatoriai sukurti veidrodžių paviršiuje suformuojant 2 µm, 4 µm ir 15 µm periodinę lūžio rodiklio moduliaciją (t.y. suformuojant vienmatę arba dvimatę fazinę difrakcinę gardelę). FK rezonatorių kampinis pralaidumas matuotas... [toliau žr. visą tekstą]

La spectrométrie photoacoustique QEPAS constitue l’une des méthodes les plussensibles pour la détection de gaz à l’état de traces. Ses performances sont étroitement liées àcelles de sa source de lumière infrarouge cohérente et de son résonateur mécanique qui détecteles ondes acoustiques. La thèse a pour objectif de développer ces deux briques élémentaires.Dans un premier temps, les performances des résonateurs mécaniques sont modélisées, permettantde mieux comprendre leur comportement. Une formule analytique originale de leurfacteur de qualité y est incorporée, permettant de prédire avec précision les pertes qu’ils subissentlorsqu’ils résonnent dans un gaz. Grâce à ces modèles, de nouveaux résonateurs optimiséssont conçus et réalisés, aboutissant à des performances améliorées. Dans un secondtemps, les sources cohérentes infrarouges QCL et OPO sont améliorées pour la photoacoustique.L’impulsion de pompe optimale pour un OPO est présentée pour distribuer au mieuxl’énergie de pompe disponible dans le temps, et ainsi maximiser le rendement de rayonnementinfrarouge disponible. Un logiciel de simulation numérique original des OPOs est égalementcréé, et permet de simuler rapidement le spectre d’émission d’un OPO quelconque. / Infrared photoacoustic spectrometry QEPAS is one of the most sensitive techniquefor trace gas sensing. The goal of the thesis is to improve the two key elements of the instrument: the mechanical resonator and the coherent infrared light source.First, the use of resonators as an acoustic waves sensor is investigated, allowing to better understandtheir behavior. Our modeling include a new analytical formula of their quality factor,predicting the amount of losses they experience when immersed within a gaz. The models areused to design and fabricate new custom resonators, leading to enhanced performances. Second,two infrared sources named QCL and OPO are optimized for the photoacoustic application.The optimal pump pulse for an OPO is derived to efficiently distribute the available pumpenergy in time, hence maximizing the yield of infrared light. A simulation software has alsobeen created for OPOs, able to quickly predict the spectrum of any type of OPO.