<p>The topic of this thesis is the development of devices for telecom applications based on poled optical fibers. The focus is on a specific function, optical switching/modulation.</p><p>Some of the most important results are summarized below. Optical switching at telecom wavelengths (1.55 μm) is demonstrated in an all-fiber switch based on a fiber with internal electrodes. The fiber is made electro-optically active with a thermal poling process in which a strong electric field is recorded in the glass at a temperature of 255 °C. After poling, the fiber is put in one arm of a Mach-Zehnder interferometer and by applying a voltage across the two electrodes the refractive index is modulated and the optical signal switched from one output port to the other. A switching voltage of 190 V at 1550 nm was achieved, which to the best of our knowledge is the lowest value reported. By carefully matching the lengths of the fibers in the two arms of the interferometer the optical bandwidth could be made as large as 20 nm. The extinction ratio, determined by the power ratio in the two arms, was 30 dB and the highest modulation frequency was 30 MHz. Poled fibers were packaged to increase the thermal and mechanical stability and to make handling easier. 40 Gb/s transmission test through the device showed no bit-error-rate performance degradation. Protection switching of a 10 Gb/s signal is also demonstrated.</p><p>The depletion region in a poled fiber was found to be wedge-shaped and very wide, 13 μm and completely overlapped with the core. In a time-resolved poling experiment the recorded electric field was measured. The sign of the field changed after ~20 min, when the depletion region passed through the core, which led to the conclusion that an electric field is present also outside of the depletion region.</p><p>A ring laser was constructed with an erbium doped fiber as the gain medium. A fiber modulator was placed inside the cavity and when a small RF signal, with a frequency matched to the cavity ground frequency, was applied to the modulator the laser was modelocked. The output pulse train contained pulses of sub ns duration and is the first demonstration of mode-locking using poled fibers.</p><p>A sampled grating with 16 channels spaced by 50 GHz was inserted into the cavity. The fiber modulator had optical bandwidth of 7 nm with center wavelength that depends on the applied voltage. By applying of 10 – 210 V to the modulator it was possible to tune the laser to 11 of the 16 channels for a total tuning range of over 4 nm.</p><p>A scheme to deposit 1 μm thin silver electrodes inside the holes of an optical fiber is demonstrated together with a new method of creating periodic electrodes by periodically ablating the silver film electrodes. The periodic electrodes are used to create a quasi-phase matched (QPM) nonlinearity in a fibers which is showed in a proof of principle experiment.</p>

For certain nonlinear Schroedinger equations there exist solutions which are called solitary waves. Addition of a potential $V$ changes the dynamics, but for small enough $||V||_{L^\infty}$ we can still obtain stability (and approximately Newtonian motion of the solitary wave's center of mass) for soliton-like solutions up to a finite time that depends on the size and scale of the potential $V$. Our method is an adaptation of the well-known Lyapunov method. For the sake of completeness, we also prove long-time stability of traveling solitons in the case $V=0$.

The work of this dissertation is centered on two non-conventional synthetic approaches to ferromagnetic nanomaterials: high-throughput experimentation (HTE) (polyol process) and continuous flow (CF) synthesis (aqueous reduction and the polyol process). HTE was performed to investigate phase control between FexCo1-x and Co3-xFexOy. Exploration of synthesis limitations based on magnetic properties was achieved by reproducing Ms=210 emu/g. Morphological control of FexCo1-x alloy was achieved by formation of linear chains using an Hext. The final study of the FexCo1-x chains used DoE to determine factors to control FexCo1-x, diameter, crystallite size and morphology. [Ag] with [Metal] provide statistically significant control of crystallite size. [OH]/[Metal] predict 100 % FexCo1-x at > 30. To conclude section 1, a morphological study was performed on synthesis of Co3-xFexOy using the polyol process. Co3-xFexOy micropillars were synthesized at various sizes. The close proximity of the particles in the nanostructure produced an optical anisotropy and was magnetically induced which is evidence for the magneto-birefringence effect. The second non-conventional synthetic approach involves continuous flow (CF) chemistry. Co nanoparticles (Ms=125 emu/g) were newly synthesized by aqueous reduction in a microreactor and had 30 ±10 nm diameter and were produced at >1g/hr, a marker of industrial-scale up viability. The final work was the CF synthesis of FexCo1-x. The FexCo1-x was synthesized with limitation to the composition. The maximum FexCo1-x phase composition at 20 % resulted from the aqueous carrier solvent triggering oxide formation over FexCo1-x.

We show some preliminary 10-37 micron high-resolution spectra taken with the Spitzer Space Telescope in 2008-9 of Mira variables distributed across the M, S and C chemical subclasses. Our entire Spitzer sample of 25 galactic Miras was observed from two to several times during this observing campaign and all have simultaneously measured near-infrared interferometric diameters acquired using the Palomar Testbed Interferometer. Because our sources are very bright for Spitzer IRS (typically 5-100 Janskys), we have excellent signal to noise and for many sources see marked changes in overall flux levels as a function of phase. Further, we are able to identify many strong emission lines and emission features due to silicate and carbon dusts and molecular constituents. We introduce the sample and the design of our experiment, discuss the data reduction required for such bright sources using Spitzer, show several examples of spectra with phase and discuss some preliminary findings. Finally, we discuss future steps for Paper II, to be presented later in the year.

Ferroelectric crystals are commonly used in nonlinear optics for frequency conversion of laser radiation. The quasi-phase matching (QPM) approach uses a periodically modulated nonlinearity that can be achieved by periodically inverting domains in ferroelectric crystals and allows versatile and efficient frequency conversion in the whole transparency region of the material. KTiOPO4 (KTP) is one of the most attractive ferroelectric non-linear optical material for periodic domain-inversion engineering due to its excellent non-linearity, high resistance for photorefractive damage, and its relatively low coercive field. A periodic structure of reversed domains can be created in the crystal by lithographic patterning with subsequent electric field poling. The performance of the periodically poled KTP crystals (PPKTP) as frequency converters rely directly upon the poling quality. Therefore, characterization methods that lead to a deeper understanding of the polarization switching process are of utmost importance. In this work, several techniques have been used and developed to study domain structure in KTP, both in-situ and ex-situ. The results obtained have been utilized to characterize different aspects of the polarization switching processes in KTP, both for patterned and unpatterned samples. It has also been demonstrated that it is possible to fabricate sub-micrometer (sub-μm) PPKTP for novel optical devices. Lithographic processes based on e-beam lithography and deep UV-laser lithography have been developed and proven useful to pattern sub- μm pitches, where the later has been the most convenient method. A poling method based on a periodical modulation of the K-stoichiometry has been developed, and it has resulted in a sub-μm domain grating with a period of 720 nm for a 1 mm thick KTP crystal. To the best of our knowledge, this is the largest domain aspect-ratio achieved for a bulk ferroelectric crystal. The sub-micrometer PPKTP samples have been used for demonstration of 6:th and 7:th QPM order backward second-harmonic generation with continuous wave laser excitation, as well as a demonstration of narrow wavelength electrically-adjustable Bragg reflectivity. / QC 20100930

All firearms within the United States are required by the Gun Control Act to be physically marked with a serial number; which is at least 0.003” in depth and 1/16” in height. The purpose of a serial number is to make each firearm uniquely identifiable and traceable. Intentional removal of a serial number is a criminal offense and is used to hide the identity and movements of the involved criminal parties. The current standard for firearm serial number restoration is by chemical etching; which is time & labor intensive as well as destructive to the physical evidence (firearm). It is hypothesized that a new technique that is accurate, precise, and time efficient will greatly aid law enforcement agencies in pursuing criminals. This thesis focuses on using a large chamber scanning electron microscope to take secondary electron (SE) images of a stamped metal plate and analyzing them using the MIRA MX 7 UE image processing software for purposes of depth determination. An experimental peak luminance value of 77 (pixel values) was correlated to the known depth (273 μm) at the bottom of the sample character. Results show that it is potentially possible to determine an unknown depth from a SEM image; using luminance values obtained in the MIRA analysis.

The topic of this thesis is the development of devices for telecom applications based on poled optical fibers. The focus is on a specific function, optical switching/modulation. Some of the most important results are summarized below. Optical switching at telecom wavelengths (1.55 μm) is demonstrated in an all-fiber switch based on a fiber with internal electrodes. The fiber is made electro-optically active with a thermal poling process in which a strong electric field is recorded in the glass at a temperature of 255 °C. After poling, the fiber is put in one arm of a Mach-Zehnder interferometer and by applying a voltage across the two electrodes the refractive index is modulated and the optical signal switched from one output port to the other. A switching voltage of 190 V at 1550 nm was achieved, which to the best of our knowledge is the lowest value reported. By carefully matching the lengths of the fibers in the two arms of the interferometer the optical bandwidth could be made as large as 20 nm. The extinction ratio, determined by the power ratio in the two arms, was 30 dB and the highest modulation frequency was 30 MHz. Poled fibers were packaged to increase the thermal and mechanical stability and to make handling easier. 40 Gb/s transmission test through the device showed no bit-error-rate performance degradation. Protection switching of a 10 Gb/s signal is also demonstrated. The depletion region in a poled fiber was found to be wedge-shaped and very wide, 13 μm and completely overlapped with the core. In a time-resolved poling experiment the recorded electric field was measured. The sign of the field changed after ~20 min, when the depletion region passed through the core, which led to the conclusion that an electric field is present also outside of the depletion region. A ring laser was constructed with an erbium doped fiber as the gain medium. A fiber modulator was placed inside the cavity and when a small RF signal, with a frequency matched to the cavity ground frequency, was applied to the modulator the laser was modelocked. The output pulse train contained pulses of sub ns duration and is the first demonstration of mode-locking using poled fibers. A sampled grating with 16 channels spaced by 50 GHz was inserted into the cavity. The fiber modulator had optical bandwidth of 7 nm with center wavelength that depends on the applied voltage. By applying of 10 – 210 V to the modulator it was possible to tune the laser to 11 of the 16 channels for a total tuning range of over 4 nm. A scheme to deposit 1 μm thin silver electrodes inside the holes of an optical fiber is demonstrated together with a new method of creating periodic electrodes by periodically ablating the silver film electrodes. The periodic electrodes are used to create a quasi-phase matched (QPM) nonlinearity in a fibers which is showed in a proof of principle experiment. / QC 20101015

Lithium niobate (LiNbO3) and KTiOPO4 (KTP) are ferroelectric crystals of considerable interest in different fields of optics and optoelectronics. Due to its large values of the nonlinear optical, electro-optic (EO), piezoelectric and acousto-optical coefficients, LiNbO3 is widely used for laser frequency conversion using the quasiphase matching (QPM) approach where the sign of nonlinearity has been periodically modulated by electric field poling (EFP). In the microwave and telecommunication field LiNbO3 is used for surface acoustic devices and integrated optical modulators. KTP and its isomorphs, on the other hand, exhibit slightly lower nonlinear coefficients but have much higher photorefractive damage thresholds, so that it is mainly used in the fabrication of QPM devices for both UV, IR and visible light generation and in high power applications. This thesis focus on different key issues: (1) accurate characterization of specific optical properties of LiNbO3, which are of interest in nonlinear and EO applications; (2) in-situ visualization and characterization of domain reversal by EFP in LiNbO3 and KTP crystals for a through understanding of the ferroelectric domain switching; (3) fabrication of periodic surface structures at sub-micron scale in LiNbO for photonic applications. An interferometric method is used for accurate measurement of ordinary and extraordinary refractive indices in uniaxial crystals, which is of great interest in the proper design of QPM crystals. A digital holography (DH) based method is presented here for 2D characterization of the EO properties of LiNbO , which is considerably interesting in the applications where the proper design of the EO device requires a spatially resolved information about the EO behaviour and the existing pointwise techniques are not sufficient. A DH method for novel in-situ monitoring of domain reversal by EFP in both LiNbO3 and KTP, is also presented here. The technqiue could be used as a tool for high fidelity periodic domain engineering but also provides information about domain kinetics, internal field and crystals defects. 3 3 3 Finally this thesis presents novel results concerning nanoscale periodic surface structuring of congruent LiNbO3. Holographic lithography (HL) is used for sub-micron period resist patterning and electric overpoling for surface domain reversal. Surface structures are obtained by selective etching. Moiré effect is also used in the HL to fabricate complicated structures with multiple periods. The depth compatibility with waveguide implementation allows foreseeing possible applications of these structures for Bragg gratings or innovative photonic crystal devices, exploiting the additional nonlinear and EO properties typical of LiNbO3. / QC 20100824

Nonlinear optical interaction in quasi-phase-matched structures opens up unique possibilities to build compact and efficient parametric devices such as optical parametric oscillators, generators, and amplifiers with tailored spectral properties. The focus of this thesis is on novel parametric interactions with periodically-poled KTiOPO4 (PPKTP) as the parametric gain medium. Optical parametric oscillators (OPOs) are attractive light sources for many applications, particularly in spectroscopy, and plays a central role in this thesis. Special attention is put on simple, yet powerful, spectral-manipulation and bandwidth-narrowing techniques for OPOs. The overall knowledge gained from these studies has been used for device construction of several tunable ultraviolet sources for biological sensing. In the case of bandwidth narrowing, the observation of decreasing spectral bandwidth in a noncollinear, idler-resonant OPO, as compared with a signal-resonant one, has been found to be due to the interplay between the material properties and the angular dispersion of PPKTP. To further reduce the bandwidth, we have shown that it is very beneficial to replace the output mirror in an OPO with a bulk Bragg grating. In fact, even close to degeneracy, where the bandwidth is typically wide, this approach is able to decrease the bandwidth drastically. Moreover, different OPO cavity designs have been examined in order to spectrally manipulate the resonant waves. By deploying a grating in a ring OPO cavity, it becomes possible to access the resonant wave and spectrally manipulated it in a zero-dispersion arrangement; the filtered wave is subsequently sent back into its own cavity as a seed signal, in a self-seeding arrangement. This particular cavity design decreases the bandwidth close to ~ 1000 times as compare to the free-running mode. An interesting phenomenon arises when two mutually coherent laser beams are used to pump a linear OPO cavity. When the pump beams intersect within the PPKTP crystal, an interference grating is formed and acts as a catalyst for the generation of new spectral sidebands through multiple cascaded four-wave mixing, in the pump, the idler and the signal directions. The spacing of these sidebands is determined geometrically by the incident pump angle, while the signals are continuously tunable over the c-band telecom window (λ ~ 1.5 μm) by rotating the cavity. Ultrabroad bandwidths have been generated in an optical parametric generator (OPG) pumped by an amplified picosecond Ti:sapphire laser. In the collinear direction the output spectrum extends over three octaves in the mid-infrared region. This enormously broad spectrum is also Fourier-filtered and subsequently used for narrowband seeding of an optical parametric amplifier (OPA). Finally, the spectral range between 285 nm and 340 nm is of importance for detection of biological substances through fluorescence spectroscopy. With this spectral region in mind a practical way to generate a tunable parametric device in the ultraviolet region is presented in the thesis. The developed ultraviolet laser is used for studies of the characteristics of biological particles. The ultraviolet source and the results from these studies, will be utilized in an integrated detection system, a so called early-warning system. / QC 20100923

Nonlinear optical frequency conversion is one of the most important key techniques in order to obtain lasers with wavelengths targeted for specific applications. In order to realize efficient and tailored lasers, the quasi-phase-matching (QPM) approach using periodically-poled ferroelectric crystals is getting increasingly important. Also understanding of damage mechanisms in nonlinear materials is necessary to be able to design reliable and well working lasers. This is especially true for high power application lasers, which is a rapidly growing field, where the damage problem normally is the ultimate limiting factor. In this thesis work, several promising novel ferroelectric materials have been investigated for nonlinear optical applications and the emphasis has been put on QPM devices consisting of periodically-poled structures. The materials were selected from three different types of ferroelectric materials: 1) MgO-doped stoichiometric LiNbO3 (MgO:SLN) and LiTaO3 (MgO:SLT), and non-doped stoichiometric LiTaO3 (SLT), 2) KTiOPO4 (KTP) and its isomorphs RbTiOPO4 (RTP), and 3) KNbO3 (KN). The focus in our investigations have been put on the spontaneous polarization switching phenomena, optimization of the periodic poling conditions, and the photochromic optical damage properties which were characterized by the help of blue light-induced infrared absorption (BLIIRA) measurements. With electrical studies of the spontaneous polarization switching, we were able to determine quantitatively, and compare, the coercive field values of different materials by applying triangularly shaped electric fields. We found that the values of the coercive fields depended on the increase rate of the applied electric field. The coercive field of KN was the lowest (less than 0.5 kV/mm) followed by the ones of KTP, SLT, and MgO:SLT (1.5 to 2.5 kV/mm). MgO:SLN, and RTP had relatively high coercive fields, approximately 5.0 to 6.0 kV/mm, respectively. Based on the domain switching characteristics we found, we successfully fabricated periodically-poled devices in all of the investigated materials with 30 μm periodicities and sample thickness of 1 mm. Blue light-induced infrared absorption (BLIIRA) has been characterized for unpoled bulk and periodically-poled samples using a high-sensitivity, thermal-lens spectroscopy technique. SLT showed a large photorefraction effect and the BLIIRA signal could not be properly measured because of the large distortion of the probe beam. The rise and relaxation time of BLIIRA, after switching the blue light on and off was in a time span of 10 to 30 sec except for KTP and its isomorphs, which needed minutes to hours in order to saturate at a fixed value. KN and MgO:SLN showed the lowest susceptibility to the induced absorption. Periodic poling slightly increased the susceptibility of KTP, MgO:SLT, and KN. Relatively high thresholds were observed in MgO:SLT and KN. By increasing the peak-power intensity of the blue light, the induced absorption for MgO:SLN, KTP and KN saturated at a constant value while that of MgO:SLT increase in a constant fashion. This trend is critical issue for the device reliability at high-power applications. / QC 20100830