Intermittent renewable energy sources, such as solar and wind, will only be viable if the electrical energy can be stored efficiently. It is possible to store electrical energy cleanly by splitting the water into oxygen (a clean byproduct) and hydrogen (an energy dense fuel) via water electrolysis. The efficiency of hydrogen production is limited, in part, by the high kinetic overpotential of the oxygen evolution reaction (OER). OER catalysts have been extensively studied for the last several decades. However, no new highly active catalyst has been developed in decades. One reason that breakthroughs in this research are limited is because there have been many conflicting activity trends. Without a clear understanding of intrinsic catalyst activity it is difficult to identify what makes catalysts active and design accordingly. To find commercially viable catalysts it is imperative that electrochemical activity studies consider and define the catalyst’s morphology, loading, conductivity, composition, and structure. The research goal of this dissertation is twofold and encompasses 1) fundamentally understanding how catalysis is occurring and 2) designing and developing a highly active, abundant, and stable OER catalyst to increase the efficiency of the OER. Specifically, this dissertation focuses on developing methods to compare catalyst materials (Chapter II), understanding the structure-compositional relationships that make Co-Fe (oxy)hydroxide materials active (Chapter III), re-defining activity trends of first row transition metal (oxy)hydroxide materials (Chapter IV), and studying the role of local geometric structure on active sites in Ni-Fe (oxy)hydroxides (Chapter V). As part of a collaboration with Proton OnSite, the catalysts studied are to be integrated into an anion exchange membrane water electrolyzer in the future. This dissertation includes previously published and unpublished co-authored material. / 10000-01-01

Le dihydrogène (H2) se présente comme le futur vecteur énergétique pour une économie basée sur des ressources propres et respectueuses de l'environnement. Il est le combustible idéal de la pile à combustible régénérative constituée de deux entités : un électrolyseur pour sa production, et une pile à combustible pour sa conversion directe en énergie électrique. Ce système présente l'avantage d'être compact et autonome. Cependant, l'amélioration de l'activité catalytique des matériaux, leur stabilité et l'élimination de métaux nobles dans leur composition sont nécessaires. Des catalyseurs bifonctionnels à base de métaux de transition associés au graphène ont alors été synthétisés. L'interaction oxyde-graphène a été étudiée sur un catalyseur Co3O4/NRGO. À faible teneur en cobalt, l'interaction entre les atomes de cobalt de l'oxyde et les atomes d'azote greffés sur les plans de graphène a été observée par voltammétrie cyclique. Cette interaction est responsable d'une diminution de la taille des nanoparticules de cobaltite et de l'activité de celles-ci vis-à-vis de la réaction de réduction du dioxygène (RRO). La substitution du cobalt par le nickel dans des structures de type spinelle (NiCo2O4/RGO) obtenu par voie solvothermale, a permis d'améliorer les performances électrocatalytiques vis-à-vis de la RRO et de la RDO. Ce matériau et un autre de type Fe-N-C préparé en collaboration avec un laboratoire de l'Université Technique de Berlin ont servi de cathode dans des études préliminaires réalisées en configuration pile à combustible alcaline à membrane échangeuse d'anion (SAFC). / Hydrogen, as an environmentally friendly future energy vector, is a non-toxic and convenient molecule for regenerative fuel cell, which connects two different technologies: an electrolyzer for H2 production, and a fuel cell for its direct conversion to electric energy. This kind of system possesses many advantages, such as lightness, compactness and more autonomy. However, improvement of activity and durability of electrode materials free from noble metals in their composition is needed. Thereby, bifunctional catalysts composed of transition metals deposited onto graphene-based materials were synthesized. The interaction between the metal atom of the oxide and the graphene doped heteroatom in the Co3O4/NRGO catalyst was investigated physicochemically. With a low cobalt loading, the interaction between cobalt and nitrogen was characterized by cyclic voltammetry, which revealed that it was responsible for decreasing the oxide nanoparticle size, as well as increasing the material activity towards the oxygen reduction reaction (ORR). The substitution of Co by Ni in the spinel structure (NiCo2O4/RGO) obtained by solvothermal synthesis, allowed the enhancement of the electrocatalytic performances towards the ORR and OER. Moreover, this catalyst as well as another material prepared in collaborative program with a lab from Technical University of Berlin were used as cathode in preliminary studies undertaken on solid alkaline fuel cell (SAFC).

Monolayer two-dimensional (2D) materials have been regarded as a hot topic in the fields of condensed matter physics, materials science, and chemistry due to their unique physical, chemical, and electronic properties. However, the research on the preparation method and properties understanding of the 2D monolayer are inadequate. In this dissertation, taking 2D nickel-iron layered double hydroxides (NiFe LDHs) and molybdenum disulfide (MoS2) as examples, the practicability of the direct synthesis of NiFe LDHs monolayer and the thermal enhancement catalytic performance of 2D MoS2 monolayer (MoS2 ML) are discussed. First, a one-pot synthetic strategy (bottom-up method) is presented to synthesize 2D NiFe-based LDHs monolayers, including NiFe, Co-, Ru-, doped, and Au-modified NiFe LDHs. The prerequisite and universality of this strategy are investigated and confirmed. The features of LDHs are characterized by advanced technologies. The obtained LDH bulks own a large interlayer spacing up to 8.2 Å, which can be facilely exfoliated into monolayers in water by hand-shaking within 10 s. As a result, the as-prepared NiFe-based LDH monolayers display a good electrocatalytic oxygen evolution reaction (OER) performance. This facile strategy paves the way for designing easily exfoliated LDHs for highly active catalysts and energy conversion devices based on other monolayer LDHs. Second, with gold-modified tape, 2D MoS2 ML is exfoliated from the bulk crystal through a micromechanical exfoliation method (top-down strategy). The thermal effects of MoS2 ML are confirmed by Raman and photoluminescence (PL) spectra. Moreover, an on-chip MoS2 ML hydrogen evolution reaction (HER) reactor is designed and fabricated. The thermal effects generate efficient electron transfer in the MoS2 ML and at the electrolyte-catalyst (MoS2 ML) interface, leading to an enhanced HER performance. Compared to the results obtained at room temperature, the MoS2 ML shows a direct thermal enhanced HER performance at higher temperatures. In summary, the findings and understandings, the direct synthesis and direct thermal enhancement catalytic performance, of 2D monolayers offer a guideline for synthesizing and catalyst application of other 2D monolayers.

Le développement de catalyseurs de la réaction de dégagement de l’oxygène (OER) pour les électrolyseurs à membrane échangeuse de protons (PEM) dépend de la compréhension du mécanisme de cette réaction. Cette thèse est consacrée à l'application de la spectroscopie d’émission de photoélectrons induits par rayons X (XPS) et de la spectroscopie de structure près du front d'absorption de rayons X (NEXAFS) operando sous une pression proche de l'ambiante (NAP) dans le but d’étudier les mécanismes de la réaction d’oxydation de l’eau sur des anodes à base d’iridium et de ruthénium et leurs dégradation dans les conditions de la réaction. Cette thèse montre les mécanismes différents de la réaction OER pour les anodes à base d’Ir et de Ru impliquant respectivement des transitions anioniques (formation d’espèce OI- électrophile) ou cationiques (formation des espèces de Ru avec l’état d'oxydation supérieur à IV) quelle que soit la nature (thermique ou électrochimique) des oxydes. / Development of oxygen evolution reaction (OER) catalysts for proton exchange membrane water electrolysis technology depends on the understanding of the OER mechanism. This thesis is devoted to the application of near-ambient pressure X-ray photoelectron spectroscopy (NAP-XPS) and near edge X-ray absorption fine structure (NEXAFS) techniques for operando investigation of the Ir, Ru - based anodes. For Ru-based systems, we observe the potential-induced irreversible transition of Ru (IV) from an anhydrous to a hydrated form, while the former is stabilized in the presence of Ir. Regarding single Ir-based anodes, the analysis of O K edge spectra reveals formation of electrophilic oxygen OI- as an OER intermediate. Higher stability of Ir catalysts supported on antimony-doped tin oxide (ATO) is related to their lower oxidation. This work demonstrates different OER mechanisms on Ir, Ru-based anodes involving anion and cation red-ox chemistry, correspondingly, regardless the oxide nature.

Research on new, environment-friendly, clean and efficient energy sources have contributed immensely to the development of new technologies for the generation and storage of electrical energy. Heterogeneous ‘electrocatalysis’ involves catalysis of redox reactions where the electrode material, termed as ‘electrocatalyst’ reduces the overpotential and maximizes the current for the processes occurring at the electrode/electrolyte interface. Efficient catalysts for hydrogen evolution reaction (HER), oxygen evolution reaction (OER), and oxygen reduction reaction (ORR) are of paramount importance for electrochemical energy generation and storage applications in water splitting, fuel cells and batteries. However, high cost of Pt catalysts that are commonly used for such applications restricts their commercial viability. In addition, there are issues related to poisoning of the surface under certain conditions. One particular case of direct methanol fuel cells involves problems of methanol tolerance as well. Hence, the on-going search in this direction, is to search for alternate catalysts that can match the performance of Pt. There is a quest for the development of stable and durable electrocatalysts/ supports for various electrochemical redox reactions particularly based on energy storage and conversion. The present thesis is structured in exploring the multi-functional aspects of ternary palladium phosphochalcogenides (PdPS and PdPSe) that possess layer-type structure with high crystallinity. They are semiconducting in nature and possess favorable electrochemical, electrical and optical properties. The chalcogenide compounds crystallize in orthorhombic symmetry with an indirect band gap close to 1.5 eV. The current study shows the versatility of ternary phosphochalcogenides in the bulk phase as well as in small sizes. The electrocatalytic activities of the chalcoenides are found to be dramatically improved by increasing the electrical conductivity by way of forming composites with reduced graphene oxide (rGO). The average crystallite size of the PdPS and PdPSe are 30 μm ±10 μm (figure 1). The composites are prepared by simple hydrothermal methods without use of any reducing agent and are characterized using various physico-chemical techniques. Figure 1. FESEM images of (a) PdPSe and (b) PdPS. In the present investigations, PdPS and its reduced graphene oxide composite (rGO-PdPS) are shown to be very efficient hydrogen evolution electrocatalysts (figure 2a). The bulk form of PdPS is found to be very active and the composite of PdPS with reduced graphene oxide improves the hydrogen evolution performance dramatically, even superior to state of the art, MoS2-based catalysts. Figure 2. (a) Linear sweep voltammograms of rGO, bulk PdPS, rGO-PdPS composite and 40 % Pt-C in 0.5 M H2SO4 solution (pH 0.8). Scan rate used is 1 mV s-1. (b) Tafel plots for PdPS, rGO, rGO-PdPS and 40 wt% Pt-C in 0.5 M H2SO4 at 1 mVs-1 scan rate. The Tafel slope and the exchange current density values associated with hydrogen evolution reaction are 46 mV dec-1 and 1.4 x 10-4 A cm-2 respectively (figure 2b). The stability of the PdPS-based catalyst is found to be excellent retaining same current densities even after thousand cycles. Moreover, post-HER characterization reveals the durability of the material even after cycling for a long time. Preliminary spectroelectrochemical investigations are attempted to gain further insight in to the HER. Subsequently, the PdPS and its composite are explored as ORR catalysts in alkaline medium. The composite of PdPS with rGO is formed to enhance the catalytic activity of pure PdPS and the electron transfer kinetics is found to be very favorable. The kinetics of the oxygen reduction reactions are followed by RDE/RRDE measurements. It is experimentally verified that the composite eletrocatalyst is very stable, efficient and methanol tolerant in alkaline medium. The characteristics of the composite catalyst are comparable with widely used standard Pt-C for ORR (figure 3a). Moreover, ternary phophochalcogenide, PdPS, combined with rGO shows good catalytic activity towards OER and it affords a current density of 10 mA cm-2 at an overpotential of η = 570 mV (figure 3b). Figure 3. (a) Comparative voltammograms for rGO, bulk PdPS, rGO-PdPS and 40 % Pt-C in 1M KOH at 1600 rpm. The potential is swept at a rate of 5 mVs-1. (b) Linear sweep voltammograms of oxygen evolution reaction on rGO-PdPS, PdPS and 40 % Pt-C in 1 M KOH electrolyte. Scan rate 5 mV s-1. Apart from its tri-functional electrocatalytic behavior, PdPS and its rGO composite act as an anode material for Li-ion batteries showing high storage capacity of lithium (figure 4). The capacity fading of bulk PdPS is analyzed using XRD and SEM. The introduction of rGO, a well-known conducting matrix, improves the performance. Palladium phosphorous selenide (PdPSe) and its composite with rGO (rGO-PdPSe) are also explored as electrocatalysts for HER, ORR and OER. They show the tri¬functional electrocatalytic behavior as well. Figure 4. Discharge capacity as a function of number of cycles for PdPS, rGO rGO-PdPS electrode at current density of 35 mAg-1 in rechargeable lithium ion battery. The next chapter deals with single or few layer PdPS where layer-type PdPS is exfoliated by several methods such as ultra-sonication and solvent exfoliation. Various microscopic and spectroscopic techniques have been used to characterize the material. These sheets show significantly improved electrocatalytic activity towards ORR and HER with notably low onset potential and low Tafel slopes. The charge storage capacity also increases by an order from its bulk counterpart. The catalyst shows excellent stability for HER and good methanol tolerance behavior towards ORR is also observed. This opens up possibilities for applications of few-layer ternary phosphosulphides in energy conversion and storage. However, one should be cautious since the exfoliation results in a slightly different composition of the material. Different aspects of electrodeposition of gallium nanoparticles on exfoliated graphite surfaces from aqueous acidic solution forms part of the next study. The electrodeposited surface is characterized by various microscopic and spectroscopic techniques. The presence of surface plasmon peak in the visible region has led us to explore the use of Ga on EG for SERS studies. This preliminary work shows that the Raman signal of R6G is enhanced in the presence of Ga deposited on EG surface. The research work presented in the next part of the thesis deals with the preparation, physicochemical, spectroscopic characterization of room temperature molten electrolytes based on amides. Room temperature ternary molten electrolyte involving a combination of acetamide, urea and gallium nitrate salt is prepared and the molten eutectic is characterized. An electrochemical process is developed for depositing gallium nitride from the ternary molten electrolyte on Au electrode. Gallium ion is reduced at low potentials while nitrate ion is reduced to produce atomic nitrogen, forming gallium nitride under certain conditions. Au coated TEM grid is used for patterning gallium nitride (figure 5). The deposited gallium nitride is further annealed at high temperature to increase the crystalinity and improve the stoichiometry of gallium nitride. Figure 5. The FESEM image of patterned gallium nitride deposited on Au coated TEM grid. Elemental mapping of Ga and N from the same region is given. The last chapter explores the prepration and uses of textured GaN tubes synthesized from GaOOH rod-like morphology. The precursor material is prepared by simple hydrothermal technique, maintaining certain value for the pH of the solution. The thermal treatment under ammonia atmosphere leads to highly crystalline, single phase textured tube- like morphology. The as-prepared material is explored as photoanodes in photoelectrochemical water splitting, dye sensitized solar cells and active substrate for SERS. The appendix-I discusses the Na-ion storage capacity by rGO-PdPS composite whereas appendix-II deals with the synthesis of InN and FeN from ternary molten electrolyte. (For figures pl refer the abstract pdf file)

Synopsis of thesis entitled “Electrochemical and Photoelectrochemical Investigations of Co, Mn and Ir-based Catalysts for Water Splitting” by Ahamed Irshad M (SR No: 02-01-02-10-11-11-1-08823) under the supervision of Prof. N. Munichandraiah, Department of Inorganic and Physical Chemistry, Indian Institute of Science, Bangalore (India), for the Ph.D. degree of the Institute under the Faculty of Science. Hydrogen is considered as the fuel for future owing to its high gravimetric energy density and eco-friendly use. In addition, H2 is an important feedstock in Haber process for ammonia synthesis and petroleum refining. Although, it is the most abundant element in the universe, elemental hydrogen is not available in large quantities on the planet. Consequently, H2 must be produced from its various chemical compounds available on earth. Currently, H2 is produced in large scale from methane by a process called steam-methane reforming (SMR). This process releases huge amount of CO2 into atmosphere as the by-product causing serious environmental issues. The development of alternate clean methods to generate H2 is a key challenge for the realization of hydrogen economy. Production of H2 gas by water splitting using electricity or sunlight is known. Low cost, high natural abundance and carbon neutrality make water as the best source of hydrogen. Thermodynamically, splitting of H2O needs 237 kJ mol-1 of energy, which corresponds to 1.23 V according to the equation, ΔG = -nFE. However, commercial electrolyzers usually operate between 1.8 to 2.1 V, due to the need of large overvoltage. The high overvoltage and subsequent energy losses are mainly associated with the sluggish kinetics of oxygen evolution reaction (OER) at the anode and hydrogen evolution reaction (HER) at the cathode. The overvoltage can be considerably reduced using suitable catalysts. Hence, the design and development of stable, robust and highly active catalysts for OER and HER are essential to make water splitting efficient and economical. Attempts in the direction of preparing several novel OER and HER catalysts, physicochemical characterizations and their electrochemical or photoelectrochemical activity are described in the thesis. A comprehensive review of the literature on various types of catalysts, thermodynamics, kinetics and mechanisms of catalysis are provided in the Chapter 1 of the thesis. Chapter 2 furnishes a brief description on various experimental techniques and procedures adopted at different stages of the present studies. Chapter 3 explains the results of the studies on kinetics of deposition and stability of Nocera’s Co-phosphate (Co-Pi) catalyst using electrochemical quartz crystal microbalance (EQCM). The in-situ mass measurements during CV experiments on Au electrode confirm the deposition of Co-Pi at potential above 0.87 V vs. Ag/AgCl, 3 M KCl (Fig.1a and b). The catalyst is found to deposit via a nucleus mediated process at a rate of 1.8 ng s-1 from 0.5 mM Co2+ in 0.1 M neural phosphate solution at 1.0 V. Further studies on the potential and electrolyte dependent stability of the Co-Pi suggest that the catalyst undergoes severe corrosion at high overpotential and in non-buffer electrolytes. Current/ Fig.1 (a) Cyclic voltammograms and (b) mass variations vs. potential of Au-coated quartz crystal in 0.1 M potassium phosphate buffer solution (pH 7.0) containing 0.5 mM Co(NO3)2 Chapter 4 deals with the electrochemical deposition of a novel OER catalyst, namely, Co-acetate (Co-Ac) from a neutral acetate electrolyte containing Co2+ ions. Use of acetate solution instead of phosphate avoids the solubility limitations and helps to get thick layer of the catalyst in a short time from concentrated Co2+ solutions. In addition, the Co-Ac is found to be catalytically superior to Co-Pi (Fig. 2a). It is also observed that the Co-Ac catalyst undergoes ion exchange with electrolyte species during electrolysis in phosphate buffer solution, which results in the formation of a hybrid Co-Ac-Pi catalyst (Fig. 2b). The presence of both acetate and phosphate ions in the catalyst and their synergistic catalytic effect enhance the OER activity. Fig.2. (a) Linear sweep voltammograms of Co-Ac in (i) phosphate and (ii) acetate electrolytes, and that of Co-Pi in (iii) acetate and (iv) phosphate electrolytes. (b) SEM image showing the formation of two layers of the catalysts after electrolysis in phosphate solution. In Chapter 5, high OER activity of an electrodeposited amorphous Ir-phosphate (Ir-Pi) is investigated. The catalyst is prepared by the anodic polarization of a carbon paper electrode in neutral phosphate solution containing Ir3+ ions (Fig. 3). The Ir-Pi film deposited on the electrode has Ir and P in an approximate ratio of 1:2 with Ir in an oxidation state higher than +4. Phosphate ions play a major role for both the electrochemical deposition process and its catalytic activity towards OER. The Ir-Pi catalyst is superior to similarly deposited IrO2 and Co-Pi catalysts both in terms of onset potential and current density at any potential in the OER region. Tafel measurements and pH dependence studies identify the formation of a high energy intermediate during oxygen evolution. Fig.3. (a) Cyclic voltammograms during the Ir-Pi deposition and (b) SEM image of Ir-Pi on C. Chapter 6 is on the preparation of a composite of Mn-phosphate (MnOx-Pi) and reduced graphene oxide (rGO) and its utilization as an OER catalyst. The composite is prepared by the simultaneous electrochemical reduction of KMnO4 and graphene oxide (GO) in a phosphate solution (pH 7.0). Various analytical techniques such as TEM, XPS, Raman spectroscopy, etc. confirm the formation of a composite (Fig. 4) and electrochemical studies indicate the favourable role of rGO towards OER. Under identical conditions, MnOx-Pi-rGO gives 6.2 mA cm-2 at 2.05 V vs. RHE whereas it is only 2.9 mA cm-2 for MnOx-Pi alone. However, the catalyst is not very stable during OER which is ascribed to slow oxidation of Mn3+ in the catalyst. Fig.4. (a) Raman spectrum and (b) TEM image of MnOx-Pi-rGO. In Chapter 7, an amorphous Ni-Co-S film is prepared by a potentiodynamic deposition method using thiourea as the sulphur source. The electrodeposit is used as a catalyst for the HER in neutral phosphate solution. The composition of the catalyst and the HER activity are tuned by varying the ratio of concentrations of Ni2+ and Co2+. The bimetallic Ni-Co-S catalyst exhibits better HER activity than both Ni-S and Co-S (Fig. 5a). Under optimized deposition conditions, Ni-Co-S requires just 150 mV for the onset of HER and 10 mA cm-2 is obtained for 280 mV overpotential. The Ni-Co-S shows two different Tafel slopes, indicating two different potential dependent HER mechanisms (Fig. 5b). Presence of two different catalytic sites which contribute selectively in different potential regions is proposed. Fig.5. (a) Linear sweep voltammograms of HER at 1 mV s-1 in 1 M phosphate solutions (pH 7.4) using (i) Ni-S, (ii) Co-S and (c) Ni-Co-S. (b) Tafel plot of Ni-Co-S showing two Tafel slopes. Photoelectrochemical OER using ZnO photoanode and Co-acetate (Co-Ac) cocatalyst is studied in Chapter 8 of the thesis. Randomly oriented crystalline ZnO nanorods are prepared by the electrochemical deposition of Zn(OH)2 followed by heat treatment at 350 ºC in air. Co-Ac is then photochemically deposited onto ZnO nanorods by UV illumination in the presence of neutral acetate buffer solution containing Co2+ ions. The hybrid Co-Ac-ZnO shows higher photoactivity in comparison with bare ZnO towards PEC water oxidation (Fig. 6). Co-Ac acts as a cocatalyst and reduces the charge carrier recombination at the electrode/electrolyte interface. Fig.6. (a) Linear sweep voltammograms of ZnO under (i) dark and (ii) light conditions, and that of Co-Ac-ZnO in (iii) dark and (iv) light in 0.1 M phosphate (pH 7.0) electrolyte. Chapter 9 deals with PEC water oxidation using α-Fe2O3 photoanode and Ir-phosphate (Ir-Pi) cocatalyst. α-Fe2O3 is prepared by direct heating of Fe film in air which in turn is deposited by the electrochemical reduction of Fe2+. Thickness of the film as well as calcination temperature is carefully optimized. In order to further enhance the OER kinetics, Ir-Pi is electrochemically deposited onto α-Fe2O3. Under optimized conditions, Ir-Pi deposited α-Fe2O3 shows around 3 times higher photocurrent than that of bare α-Fe2O3 at 1.23 V vs. RHE (Fig. 7). Ir-Pi acts as a cocatalyst for OER and reduces the photogenerated charge carrier recombination. Fig.7. Photocurrent variation of α-Fe2O3 electrode at 1.23 V vs. RHE for (i) front and (ii) back side illuminations, against Ir-Pi deposition time. The thesis ends with a short summary and future prospectus of studies described in the thesis. The research work presented in the thesis is carried out by the candidate as the part of Ph.D. program. Some of the results have already been published in the literature and some manuscripts are under preparation. A list of publications is included at the end of the thesis. It is anticipated that the studies reported in the thesis will constitute a worthwhile contribution.