Spelling suggestions: "subject:"article size distribution."" "subject:"1article size distribution.""
11 |
Particle Size Distribution of Gypseous SamplesArnett, Morgan P. 16 January 2010 (has links)
Particle size distribution (PSD) of gypseous soils is important in the soil science community. When gypsum constitutes a major portion of the soil, its removal prior to PSD analysis distorts the results and may lead to textures that do not relate to conditions in the field. In order to understand the true characterization of the soil and the gypsum particles, the entire soil sample should be analyzed. Four different approaches to the BaCl2 method presented in the literature (Hesse, 1976, Matar and Douleimy, 1978, Viellefon, 1979) were used to evaluate the use of BaCl2 solution to reduce the solubility of gypsum by forming a protective coating of BaSO4 around gypsum particles. Results showed that the BaCl2 method was unsatisfactory, as dispersion of clays was not sufficient to allow particle size analysis using the pipette method. A procedure using a laser diffraction particle size analyzer (LPSA) was also evaluated. As gypsum is insoluble in methanol, methanol was selected as a possible solution, but it caused flocculation of clays and could not be used to analyze samples containing silicate clays. Gypsum saturated water containing Na hexametaphosphate was evaluated as a solution. First, 20 non-gypseous samples were analyzed on a sand-free basis using saturated gypsum water with Na hexametaphosphate. Results were used to establish a relationship comparing LPSA results and pipette results. An equation y = 1.37x + 2.03 was established relating LPSA clay percent by volume (x) to the pipette clay percent by weight (y). The equation had a R2 value of 0.84 and was significant at the 1% level. From this equation a comparison of 21 gypseous samples was made, between clay percentages of the pipette method and the LPSA method. Results indicate that LPSA can be used to give a satisfactory particle size distribution of gypseous soils when coupled with sand analysis by sieving.
|
12 |
Particle Size Distribution of Gypseous SamplesArnett, Morgan P. 16 January 2010 (has links)
Particle size distribution (PSD) of gypseous soils is important in the soil science community. When gypsum constitutes a major portion of the soil, its removal prior to PSD analysis distorts the results and may lead to textures that do not relate to conditions in the field. In order to understand the true characterization of the soil and the gypsum particles, the entire soil sample should be analyzed. Four different approaches to the BaCl2 method presented in the literature (Hesse, 1976, Matar and Douleimy, 1978, Viellefon, 1979) were used to evaluate the use of BaCl2 solution to reduce the solubility of gypsum by forming a protective coating of BaSO4 around gypsum particles. Results showed that the BaCl2 method was unsatisfactory, as dispersion of clays was not sufficient to allow particle size analysis using the pipette method. A procedure using a laser diffraction particle size analyzer (LPSA) was also evaluated. As gypsum is insoluble in methanol, methanol was selected as a possible solution, but it caused flocculation of clays and could not be used to analyze samples containing silicate clays. Gypsum saturated water containing Na hexametaphosphate was evaluated as a solution. First, 20 non-gypseous samples were analyzed on a sand-free basis using saturated gypsum water with Na hexametaphosphate. Results were used to establish a relationship comparing LPSA results and pipette results. An equation y = 1.37x + 2.03 was established relating LPSA clay percent by volume (x) to the pipette clay percent by weight (y). The equation had a R2 value of 0.84 and was significant at the 1% level. From this equation a comparison of 21 gypseous samples was made, between clay percentages of the pipette method and the LPSA method. Results indicate that LPSA can be used to give a satisfactory particle size distribution of gypseous soils when coupled with sand analysis by sieving.
|
13 |
The modeling of arsenic removal from contaminated water using coagulation and sorptionKim, Jin-Wook 01 November 2005 (has links)
To achieve predictive capability for complex environmental systems with coagulation and arsenic sorption, a unified improved coagulation model coupled with arsenic sorption was developed. A unified coagulation model coupled with arsenic sorption was achieved by the following steps: (1) an improved discretized population balance equation (PBE) was developed to obtain the exact solution of conventional coagulation, (2) the improved PBE was extended to an adjustable geometric size interval having higher numerical stability, accuracy, and computational efficiency than existing models for fractal aggregate coagulation that includes agglomeration and fragmentation, (3) a surface complexation equilibrium model and a sorption kinetic model was introduced to predict arsenic sorption behavior onto hydrous metal oxide surfaces, and (4) an improved discretized PBE was coupled with arsenic sorption kinetics and equilibrium models by aid of collision efficiency ?? depending on surface charge (potential) on the hydrous metal oxide particles, colliding particle size ratio, and fluid strain-rate in applied flow system. The collision efficiency ?? into the improved (r,r)ij(r,r)ijdiscretized coagulation model for fractal aggregate yielded a unified improved coagulation model coupled with arsenic sorption kinetics and the equilibrium model. Thus, an improved unified coagulation model could provide high statistical accuracy, numerical stability, and computational efficiency to enhance predictive capability for behavior of arsenic sorption and fractal colloid particle aggregation and break-up, simultaneously. From the investigation, it is anticipated that the unified coagulation model coupled with arsenic sorption kinetics and equilibrium will provide a more complete understanding of the arsenic removal mechanism and its application to water/wastewater treatment. Further, this coupled model can be applied to other water and wastewater treatment systems combined with sorption and filtration processes. These combined processes can be optimized by the coupled model that was developed in this study. By simulating the arsenic sorption and particle size distribution as a pretreatment before filtration (sand filtration or membrane filtration), the overall arsenic removal efficiency and operation cost can be estimated.
|
14 |
Modelling studies of the interaction between homogenisation, centrifugation and inclusion body dissolution / by Heng Ho Wong.Wong, Heng Ho January 1997 (has links)
Bibliography: leaves 208-216. / xxii, 231 leaves : ill. ; 30 cm. / Title page, contents and abstract only. The complete thesis in print form is available from the University Library. / The aim of this thesis is to define optimal centrifuge operating conditions for inclusion body recovery. Special attention is directed to the interaction of the recovery step with upstream and downstream processes. A new Eschenchia coli debris sizing method, Asoc, is developed to overcome the limitations of existing sizing methods. / Thesis (Ph.D.)--University of Adelaide, Dept. of Chemical Engineering, 1997?
|
15 |
Physicochemical properties of protein inclusion bodies / by Norbertus Djajasantosa Wangsa-Wirawan.Wangsa-Wirawan, Norbertus Djajasantosa January 1999 (has links)
Bibliography: leaves 182-198. / xv, 207 leaves : ill. (some col.) ; 30 cm. / Title page, contents and abstract only. The complete thesis in print form is available from the University Library. / Improvements in the current production system of inclusion bodies and the downstream processing sequence are essential to maintain a competitive advantage in the market place. Optimisation of fermentation is considered to improve production yield; then flotation as a possible inclusion body recovery method. / Thesis (Ph.D.)--University of Adelaide, Dept. of Chemical Engineering, 2000?
|
16 |
Método de formulação de argamassas de revestimento baseado em distribuição granulométrica e comportamento reológico. / Formulation method for rendering mortars based on particle size distribution and rheological behavior.Fábio Alonso Cardoso 11 September 2009 (has links)
O desempenho final das argamassas depende das matérias-primas e de suas proporções na formulação, pois estas determinam o comportamento do material na etapa de aplicação e a microestrutura final do material endurecido. Entre as patologias de revestimentos, a falha de aderência é um dos fenômenos mais freqüentes, sendo originada pela incompatibilidade entre o comportamento reológico da argamassa e a energia de lançamento utilizada, resultando em defeitos na interface argamassa substrato. A adequação das características reológicas das argamassas às solicitações envolvidas na aplicação fornece condições de processamento mais favoráveis para a obtenção das máximas propriedades finais do revestimento. Assim, o objetivo do trabalho é desenvolver critérios de formulação, baseados nas características das matérias-primas, nos modelos de empacotamento de partículas e nos comportamentos reológicos, de modo a obter um método de formulação de argamassas. O método de squeeze-flow foi desenvolvido com sucesso para avaliação reológica de argamassas, sendo as principais variáveis experimentais foram estudadas, assim como o efeito do tipo de mistura no comportamento reológico. Procedimento para quantificação da segregação pasta-agregado foi criado, tendo em vista o intenso efeito que este fenômeno exerce sobre o comportamento reológico em squeeze-flow, especialmente em baixas velocidades. Foi ainda comprovado que o squeeze-flow tem boa relação com a percepção do pedreiro, principalmente, nas etapas de lançamento e aperto. Diversas argamassas nacionais e européias foram caracterizadas, resultando em um mapeamento das características de formulação, do comportamento reológico e das propriedades no estado endurecido. Através da aplicação de conceitos de empacotamento e distância de separação de partículas, foi verificado que a otimização do empacotamento de agregados permite um melhor aproveitamento da pasta para promover argamassas com comportamento reológico mais adequado à aplicação ou com menor consumo de finos e água. As correlações estabelecidas entre as características no estado fluido e as propriedades no estado endurecido permitem prever o comportamento das propriedades no estado endurecido com boa confiabilidade. Por fim, são descritas diretrizes sistemáticas para a formulação de argamassas considerando requisitos de desempenho tanto no estado fresco quanto no endurecido. / The in-use performance of rendering mortars depends on the raw materials features and their content in the formulation, since they have major influence on the material behavior during emplacement, as well as, on its final properties. Adherence failure is one of the most frequent problems of this class of building materials, caused by the incompatibility between rheological behavior and the application process, generating mortar/substrate interface flaws. A rheological behavior more suitable to the application demands, provides appropriate conditions to obtain maximum final rendering properties. Therefore, the main goal of this work is to develop mix-design parameters based on raw materials features, particle packing models and rheological behavior, in order to create a mix-design method for mortars. Squeeze-flow technique was successfully adapted for the rheological evaluation of rendering mortars, and the most important experimental parameters were studied. The method is sensitive enough to measure rheological changes as a function of the mixing process applied. Considering that phase segregation plays an important role on the rheological behavior of concentrated suspensions especially at low speeds, a method was developed to measure paste-aggregate segregation. It was also established that the squeeze-flow agrees well with the workers perception during manual emplacement. Several Brazilian and European products were evaluated, and significant differences were determined on the formulation features, rheological behavior and hardened properties. Using models of particle packing and particle distance, it was verified that optimized packing of aggregates enhances rheological behavior and can also allow the reduction of water and fine particles consumption. The experimental relationships established between fresh characteristics, rheological behavior and final properties can be used to predict hardened features and properties with fair confidence. Lastly, mix-design suggestions are made considering both fresh and hardened performance.
|
17 |
Stochastic simulation of soil particle-size curves in heterogeneous aquifer systems through a Bayes space approachMenafoglio, A., Guadagnini, A., Secchi, P. 08 1900 (has links)
We address the problem of stochastic simulation of soil particle-size curves (PSCs) in heterogeneous aquifer systems. Unlike traditional approaches that focus solely on a few selected features of PSCs (e.g., selected quantiles), our approach considers the entire particle-size curves and can optionally include conditioning on available data. We rely on our prior work to model PSCs as cumulative distribution functions and interpret their density functions as functional compositions. We thus approximate the latter through an expansion over an appropriate basis of functions. This enables us to (a) effectively deal with the data dimensionality and constraints and (b) to develop a simulation method for PSCs based upon a suitable and well defined projection procedure. The new theoretical framework allows representing and reproducing the complete information content embedded in PSC data. As a first field application, we demonstrate the quality of unconditional and conditional simulations obtained with our methodology by considering a set of particle-size curves collected within a shallow alluvial aquifer in the Neckar river valley, Germany.
|
18 |
INFLUENCE OF ELECTROSTATIC CHARGE UPON THE DEPOSITION BEHAVIOR OF PHARMACEUTICAL AEROSOLS WITHIN CASCADE IMPACTORSMohan, Megha 16 August 2012 (has links)
Cascade impactors, routinely used for in vitro particle size characterization of pharmaceutical aerosols, are calibrated using dilute, charge-neutralized, monodisperse aerosols. But pharmaceutical aerosols are known to generate concentrated, inherently charged, polydisperse aerosol clouds. A computational model of the Andersen Cascade Impactor (ACI) suggested that the presence of charge on aerosol particles may influence their deposition within the ACI, but experimental validation of the model is warranted. This dissertation investigates the influence of electrostatic charge upon the deposition behavior of aerosols within cascade impactors, to address the impact of charge on particle size characterization. The influence of applied charge upon the deposition pattern and aerodynamic particle size distribution (APSD) of commercially available pressurized metered dose inhalers (pMDIs) within the Electrical Low Pressure Impactor (ELPI) was examined. Electrostatic properties were modified using an external voltage source in conjunction with the ELPI corona charger and observed to be dependent on the formulation and device packaging. Induced artificial charge on the aerosol particles influenced the deposition pattern within the impactor, but did not result in a significant change in the apparent APSD. An experimental apparatus capable of producing charge neutralized and charged aerosol, with targeted deposition on the CFD predicted ‘charge sensitive’ ACI stages, was developed. In vitro results were observed to be in partial agreement with the CFD predictions. While charge influenced the deposition pattern in the ACI with increased deposition observed in the charger and on the upper stages of the ACI, it did not influence the apparent APSD of the aerosol. Electrostatic charge effects on deposition behavior within cascade impactors were delineated with respect to space charge and image charge effects by investigating the influence of impactor grounding, particle size, stage coating and loading. While the deposition pattern within the ACI was influenced by charge, only stage coating and stage loading resulted in a small, significant difference in the apparent APSD, which may not be practically relevant due to the variability associated with in vitro aerosol testing. Similar trends were observed in the deposition behavior of charge neutralized and charged aerosol within an abbreviated ACI system compared to the full resolution ACI.
|
19 |
The application of the attainable region analysis in comminution.Khumalo, Ngangezwe 09 June 2008 (has links)
ABSTRACT
This work applies the concepts of the attainable region for process synthesis
in comminution. The attainable region analysis has been successfully applied
for process synthesis of reactor networks. The Attainable Region is defined
as the set of all possible output states for a constrained or unconstrained
system of fundamental processes (Horn, 1964). A basic procedure for
constructing the attainable region for the fundamental processes of reaction
and mixing has been postulated in reaction engineering (Glasser et al., 1987).
This procedure has been followed in this work to construct the candidate
attainable region for size reduction processes as found in a size reduction
environment.
A population balance model has been used to characterise the evolution of
particle size distributions from a comminution event. Herbst and Fuerstenau
(1973) postulated the dependency of grinding on the specific energy. A
specific energy dependent population balance model was used for the
theoretical simulations and for the fitting of experimental data.
A new method of presenting particle size distributions as points in the
Euclidian space was postulated in place of the traditional cumulative
distribution. This allows successive product particle size distributions to be
connected forming a trajectory over which the objective function can be
evaluated. The curve connects products from successive batch grinding
stages forming a pseudo-continuous process.
Breakage, mixing and classification were identified as the fundamental
processes of interest for comminution. Agglomeration was not considered in
any of the examples. Mathematical models were used to describe each
fundamental process, i.e. breakage, mixing and classification, and an
The application of the attainable region analysis in comminution Abstract
algorithm developed that could calculate the evolution of product particle size
distributions. A convex candidate attainable region was found from which
process synthesis and optimisation solutions could be drawn in two
dimensional Euclidian space. As required from Attainable Region Theory, the
interior of the bounded region is filled by trajectories of higher energy
requirements or mixing between two boundary optimal points.
Experimental validation of the proposed application of the attainable region
analysis results in comminution was performed. Mono-sized feed particles
were broken in a laboratory ball mill and the products were successfully fitted
using a population balance model. It was shown that the breakage process
trajectories were convex and they follow first order grinding kinetics at long
grind times. The candidate attainable region was determined for an objective
function to maximise the mass fraction in the median size class 2. It was
proved that the same specific energy input produces identical products. The
kinematic and loading conditions are supposed to be chosen as a subsequent
event after the required specific energy is identified.
Finally the fundamental process of classification was added to the system of
breakage and mixing. The attainable regions analysis affords the opportunity
to quantify exactly the reduction in energy consumption due to classification
in a comminution circuit, thus giving optimal targets. Classification showed the
potential to extend the candidate attainable region for a fixed specific energy
input. The boundary of the attainable region is interpreted as pieces of
equipment and optimum process conditions. This solves both the original
process synthesis and successive optimisation problems.
|
20 |
Investigation of size, concentration and particle shapes in hydraulic systems using an in-line CMOS image matrix sensorKornilin, Dmitriy V. January 2018 (has links)
The theoretical and experimental investigation of the novel in-line CMOS image sensor was performed. This sensor is aimed to investigate particle size distribution, particle concentration and shape in hydraulic liquid in order to implement the proactive maintenance of hydraulic equipment. The existing instruments such as automatic particle counters and techniques are not sufficiently enough to address this task because of their restricted sensitivity, limit of concentration to be measured and they cannot determine particle shape. Other instruments cannot be used as inline sensors because they are not resistant to the arduous conditions such as high pressure and vibration. The novel mathematical model was proposed as it is not possible to use previously developed techniques based on using optical system and complicated algorithms. This model gives the output signal of the image sensor depending on the particle size, its distance from the light source (LED) and image sensor. Additionally, the model takes into account the limited exposure time and particle track simulation. The results of simulation based on the model are also performed in thesis. On the basis of the mathematical model the image processing algorithms were suggested in order to determine particle size even when this size is lower than pixel size. There are different approaches depending on the relation between the size of the particle and the pixel size. The approach to the volume of liquid sample estimation was suggested in order to address the problem of low accuracy of concentration measurement by the conventional automatic particle counters based on the single photodiode. Proposed technique makes corrections on the basis of particle velocity estimation. Approach to the accuracy estimation of the sensor was proposed and simulation results are shown. Generally, the accuracy of particle size and concentration measurement was considered. Ultimately, the experimental setup was used in order to test suggested techniques. The mathematical model was tested and the results showed sufficient correlation with the experiment. The zinc dust was used as a reference object as there are the particles within the range from 1 to 25 microns which is appropriate to check the sensitivity. The results of experiments using reference instrument showed the improved sensitivity and accuracy of volume measured compared to the reference one.
|
Page generated in 0.1142 seconds