Este trabalho teve por objetivo desenvolver um processo de sinterização a plasma utilizando gaiola catódica para a sinterização de amostras de alumínio, para atmosferas de argônio, hidrogênio e nitrogênio. Avanços recentes na sinterização a plasma motivaram a investigação sobre seus benefícios para o alumínio e se a técnica de tela ativa, em particular com o uso de gaiola catódica, é capaz de contornar alguns problemas encontrados na sinterização deste material, como a presença de uma camada passiva de óxido e a expansão volumétrica após a sinterização para certos parâmetros de processo. A sinterização foi realizada em três processos: convencional, plasma direto e plasma com gaiola catódica. Para o processo convencional utilizou-se atmosferas de argônio e nitrogênio e, para os processos a plasma, utilizou-se atmosferas de argônio, hidrogênio e nitrogênio. Houve queda na densificação média após a sinterização em todos os processos. Tanto o processo a plasma direto e com gaiola catódica resultaram na menor queda de densificação. A atmosfera de nitrogênio mostrou-se a mais efetiva nos processos avaliados, indo ao encontro com o reportado na literatura consultada. Houve aparente endurecimento superficial das amostras sinterizadas a plasma direto. As amostras sinterizadas a plasma com gaiola catódica obtiveram homogeneidade nos valores de microdureza superficial e transversal entre as atmosferas, concordando com o esperado do uso desta técnica. O processo a plasma direto produziu amostras com maior rugosidade em comparação com os outros processos, não havendo influência significativa da atmosfera de sinterização neste aspecto. Foi detectada a presença de zinco na superfície de amostras provenientes do processo convencional com nitrogênio e do processo a plasma com gaiola catódica utilizando argônio e nitrogênio, sendo confirmado pela análise química. Houve formação de nitreto de alumínio apenas no processo convencional com nitrogênio. O processo a plasma com gaiola catódica mostrou-se o mais promissor por apresentar bons resultados em relação aos obtidos nos outros processos avaliados e por ser capaz de preservar a integridade superficial das amostras. É possível promover a melhora das propriedades superficiais do alumínio com o uso de gaiola catódica através de tratamentos termoquímicos concomitantes com a sinterização, tendo em vista os benefícios relatados na literatura. / This study aimed to develop a plasma sintering process using cathodic cage for sintering aluminum samples for argon, hydrogen and nitrogen atmospheres. Recent advances in plasma sintering motivated the research into its benefits for the aluminum and if the active screen technique, in particular the use of cathodic cage, can overcome some problems encountered in the sintering of this material, as the presence of a passive oxide layer and volumetric expansion after sintering for certain process parameters. Sintering was carried out in three processes: conventional, direct plasma and plasma with cathodic cage. For the conventional process was used argon and nitrogen atmospheres and for the plasma processing was used argon, hydrogen and nitrogen atmospheres. There was a decrease in average densification after sintering in all processes Both the direct plasma and cathodic cage plasma processes resulted in the smallest drop of densification. The nitrogen atmosphere proved to be the most effective in al processes evaluated, meeting with the reported in the literature. There was apparent superficial hardening of the samples sintered in direct plasma. Samples sintered in cathodic cage plasma obtained homogeneity in values of surface and cross section hardness between the atmospheres, according to the expected use of this technique. The direct plasma process produced samples with higher surface roughness compared with other processes, with no apparent influence of the atmosphere in this respect. It was detected the presence of zinc in the sample surface from the conventional process with nitrogen and cathodic cage plasma process with argon and nitrogen being confirmed by chemical analysis. The phase analysis on the sintered samples with nitrogen accused the formation of aluminum nitride for the conventional process. The cathodic cage plasma process proved to be the most promising for showing good results compared to those obtained in the other processes evaluated and to be able to preserve the surface integrity of the samples. It is possible to promote the improvement of the surface properties of aluminum with the use of active screen via thermochemical treatments concomitant with the sintering, in view of the benefits reported in the literature.

Four silicon nitride powder blends vary in starting powder characteristics, glass chemistry, and phase composition. This work focuses on how these properties influence densification behavior, microstructural development, and the resulting mechanical performance of dense ceramics. Previous work completed on alpha-rich, low oxide containing (8 wt%), and fine silicon nitride powder (GS-44) showed high hardness equiaxed with grained ceramic. GS-44 served as an excellent precursor for the matrix phase material in graphene reinforced composites, which resulted in 235% increase in toughness and high hardness retention [1] with the addition of 1.5 vol% graphene. As the GS-44 powder is no longer in production, investigative work into other commercial powders and customization of powder blends was initiated. Commercial blends were selected based on availability, high alpha content, fine particle size, and additive chemistry (Al2O3, MgO, and Y2O3). The objective was to understand which powder characteristics led to a ceramic design that contained high hardness, strength, and toughness properties in order to increase the use of silicon nitride in extreme temperature environments. One such example is aerospace and structural applications that require a high-performance material that is lightweight and good thermal stability. Strong covalent bonding in silicon nitride make densification of powders extremely difficult; thereby, sintering additives are necessary to promote liquid phase sintering processes. Compaction of ceramic powders was carried out using a spark plasma sintering (SPS) furnace by utilizing a pulsed direct current through a conductive graphite die that encapsulates the sample powder. SPS was preferred over other conventional sintering methods owing to its high heating rate and short dwell times at the sintering target temperature. Thus, SPS provides superior control for tailoring the final silicon nitride properties by producing a hard alpha-phase and tough beta-phase microstructures. The custom blend developed had an appreciable amount of media wear included during the milling process that increased the additive content. Development of the custom blend was used to understand the effect of a larger additive content. Commercial GS-44 blend was used as the control to track the effect of adjusting specific surface area and oxide content in silicon nitride powder systems (HCS-M, C-R3, and UA-SN). The mechanical results for the four matrix systems, showed that toughness increased with grain coarsening and minimization of alumina content in beta silicon nitride. Based on these findings it is important to determine tradeoffs (i.e. balance of high hardness, toughness, and strength) to engineer an optimal ceramic that can be used for structural and aerospace applications.

Diploma thesis occupy with preparation of porous material from magnesium powder with a HAp admixture by cold pressing followed by spark plasma sintering (SPS). This thesis contain both preparation of bulk material, diffusion plot and charakterization of materials based on the compaction process conditions. On the basis of physical mechanical characteristics, the impact of the pressing process on the subsequent sintering and the resulting material properties are evaluated. Bulk material is characterized considering to structure and physical–mechanical properties. Properties of final metarial will serve to optimize conditions for process of bulk material preparation.

This diploma thesis deals with research and preparation of bulk materials based on the Mg–Al–Ti system. The theoretical part summarizes the basic knowledge about magnesium alloys, focusing mainly on Mg–Al and Mg–Ti systems. Furthermore, basic information on powder metallurgy methods was included here, from the production of powder materials, through their compaction, to heat treatment and spark plasma sintering (SPS). The theoretical part ends with literature review on the current research of the Mg–Al–Ti system. In the experimental part, bulk materials based on the Mg–Al–Ti system was prepared using traditional methods of powder metallurgy, as well as using the SPS method. The microstructure of the material, elemental and phase composition was examined in this thesis. Subsequently, Vickers hardness and flexural strength were measured, and fractographic observation of the fracture surface was performed. It was found that the aluminum was completely dissolved during the heat treatment, but the titanium particles remained almost intact in the material and worked as a particulate reinforcement. Materials prepared by methods of conventional powder metallurgy showed increased porosity compared to materials prepared by the SPS, resulting in lower hardness and flexural strength. The hardness increased with increasing the amount of aluminum and titanium and with the amount of magnesium phase . Fractographic observation of the fracture surface suggests that a diffuse connection between the reinforcement and the matrix may have occurred after the sintering process.

Les propriétés idéales d’un matériau de blindage sont la combinaison d’une extrême dureté pour casserles noyaux des projectiles et d’une grande ductilité pour résister à l’impact et arrêter les fragments du projectile. Or cettecombinaison de propriétés est incompatible avec un matériau unique. Pour pallier ce problème, les concepteurs de blindageassocient un matériau dur (céramique) à un matériau ductile (métal). Une autre solution serait de réaliser un matériauprésentant un gradient de propriétés mécaniques : dans le cas présent, d’une très grande dureté de la face avant à une grandeductilité de la face arrière. Les technologies non conventionnelles de frittage telles que le Spark Plasma Sintering (SPS)permettent d’assembler ou de fritter/assembler des matériaux aux caractéristiques aussi différentes et complémentaires. Ils’agit donc d’étudier les conditions d’assemblage ou de cofrittage de tels matériaux (dans le cas présent, Al2O3 et Ti) ainsique l’influence de la microstructure résultante de l’ensemble sur sa performance balistique.La première partie de ce travail a porté sur la caractérisation de l’alumine et du titane. Cinq poudres d’alumines ontété étudiées d’un point de vue comportement au frittage. Trois d’entre elles sont retenues en raison de leurs microstructuresintéressantes, proches en termes de densité et de taille de grains. Ces alumines ont été caractérisées mécaniquement (dureté,ténacité, résistance à la rupture) et balistiquement pour n’en garder qu’une dans la deuxième partie du travail. Le titane, frittédans les mêmes conditions que l’alumine, a montré qu’il n’avait malheureusement pas les propriétés attendues (absence deductilité).La seconde partie du travail a montré que l’obtention de MGFs sains à partir de Al2O3 et Ti uniquement est délicate,que ce soit avec un intercalaire sous forme de monocouche ou de multicouche. La forte affinité du titane avec l’oxygène(formation d’oxyde ou en insertion) et le carbone (formant des carbures), ainsi que sa réactivité avec l’alumine (produisantdes intermétalliques) rend le MGF fragile et incapable d’accommoder les contraintes résiduelles d’élaboration. L’insertiond’une faible proportion de nickel (plus ductile et moins réactif vis-à-vis de l’oxygène que le titane) dans les composites apermis d’obtenir des MGFs sains, dont le comportement balistique a pu être évalué. / The objective is to improve ballistic performance of armors. A perfect armor combines ductility to resistto the impact and high hardness to stop projectile’s fragments. However, such an association of properties is inconsistent witha single material. The solution is to perform a functionally graded material (FGM) with a ductile metal at the back side of thesample and a hard ceramic on the top side. Non-conventional technologies like Spark Plasma Sintering allow joining orsintering all types of materials with different and additional properties. Furthermore, with this technique, high heating ratescan be achieved, limiting grain growth and resulting in a fine microstructure. The goal is to study joining conditions or cosinteringof such materials (in this case, Al2O3 and Ti), as well as the resulting microstructure on the ballistic efficiency.The first part of the study focused on the characterization of alumina and titanium. Five powders of alumina werestudied from a sintering point of view. Three of which were selected because of their interesting microstructures, close indensities and grain sizes. These ceramics have been characterized mechanically (hardness, toughness and strength) andballistically. One of them is adopted to realize FGM. Titanium, sintered with the same conditions, unfortunately, doesn’t haveexpected properties (absence of ductility).The second part of the work showed that the preparation of FGM without cracks from Al2O3 and Ti only ischallenging, with an interlayer with one or more layers. The strong affinity of Ti with oxygen (formation of oxides orinsertion) with C (forming carbides) and its reactivity with alumina (forming intermetallics) make the FGM brittle and enablethe release of residual stresses during the process. By adding a low amount of nickel (more ductile and less reactive withoxygen and titanium) in composites, FGMs almost without cracks were obtained. The latter were evaluated ballistically.

Ce travail porte sur l'évolution microstructurale d'un alliage TiAl lors du frittage par un procédé appelé Spark Plasma Sintering (SPS). Les poudres initiales, élaborées par atomisation, sont constituées principalement d'une phase métastable. Les transformations qui accompagnent le retour à l'équilibre de cette dernière durant un chauffage sont finement caractérisées par MEB, MET et EBSD. Ces transformations seront ensuite utilisées comme marqueur thermique lors de la densification SPS afin de mieux estimer les amplitudes des gradients thermiques et mécaniques du procédé de frittage. Les mécanismes de densification responsables de la formation des cous sont discutés, ainsi que les origines des hétérogénéités microstructurales des échantillons complètement densifiés. Un comparatif des mécanismes de densification et des microstructures finales entre une poudre broyée et une poudre non broyée est dressé. Enfin, l'influence de l'application d'une contrainte dynamique pendant la compaction au moyen d'un dispositif original est présentée / This work focuses on the microstructure evolution of a TiAl alloy during sintering by a process called Spark Plasma Sintering (SPS). The initial powders, elaborated by atomization, consist primarily of a metastable phase. The transformations of the return to equilibrium of the latter during heating are finely characterized using SEM, TEM and EBSD. These phase transformations are then used as a thermal indicator during the SPS densification to estimate the thermal and mechanical gradients. The densification mechanisms responsible for the neck formation and the origins of the microstructure heterogeneities of fully densified samples are discussed. A comparison between the densification mechanisms and the final microstructures of a milled powder and a no milled powder is showed. Finally, the effect of the application of a dynamic stress during the compaction using an original process is presented

L'utilisation de la thermoélectricité passe par une amélioration du rendement du module thermoélectrique à travers l'optimisation de ses dimensions et l'augmentation du facteur de mérite des matériaux thermoélectriques, mais aussi par une réduction des coûts de synthèse et de mise en forme. Dans le cadre de cette thèse nous nous sommes intéressés à la synthèse de β–Zn4Sb3 nanométrique par une méthode de chimie douce à faible dépense énergétique. Nous avons étudié la mise en forme de ce matériau par des technologies d'impression qui permettent d'atteindre les dimensions optimales et présentent un coût réduit. β-Zn4Sb3 est obtenu en deux étapes : une synthèse à reflux suivie d'un traitement thermique à 400°C sous vide secondaire. La composition chimique (DRX, affinement Rietveld), la morphologie (MEB, TEM) et la stabilité en température (spectroscopie Raman) de la poudre sont étudiées. β-Zn4Sb3 ainsi obtenu est densifié par SPS et ses propriétés thermoélectriques sont mesurées montrant une augmentation du facteur de mérite pour des températures inférieures à 100°C. Au dessus de cette température, la présence de porosité et de zinc augmente la résistivité électrique et la conductivité thermique et les échantillons ont un facteur de mérite de 0,6 à 400°C. Enfin, la poudre est mise en forme par sérigraphie et atomisation sur substrat en verre et en Kapton. Le β-Zn4Sb3 montre une forte résistivité électrique juste après impression mais l'application de traitement mécanique et thermique permet de la diminuer. Le facteur de mérite estimé des dépôts est de 0,06 à 400°C. Cependant le faible coût de mise en forme et la possibilité d'automatisation rendent ces techniques viables. / Use of thermoelectricy involves an increase of the module efficiency. In this purpose we need to optimize the dimension of the module and to increase the figure of merit of thermoelectric materials. But we also need to reduce the synthesis and shaping cost. Within the framework of this thesis, we focused on the synthesis of β-Zn4Sb3 nanoparticles by a low energy technique: wet chemistry. We also studied the shaping of this material by printing technologies. These cost-effective technologies allow reaching optimized dimensions. β-Zn4Sb3 is synthesized in two steps: a reflux synthesis flowed by a thermal treatment at 400 °C under vacuum. Chemical composition (XRD, Rietveld refinement), morphology (SEM, TEM) and thermal stability of the powder are studied. The as product β-Zn4Sb3 is densified by SPS and we measured its properties. They show an increase of the figure of merit for temperatures below 100 °C. However above this temperature the presence of zinc and porosity increase electric resistivity and thermal conductivity, leading to a figure of merit of 0.6 at 400 °C. Finally the powder is shaped by two printing technologies: screenprinting and atomization on glass and Kapton substrate. Just after printing the samples show a high electrical resistivity but a decrease is observed after mechanical and thermal treatment. The estimate figure of merit of printing β-Zn4Sb3 is 0.06 at 400 °C. However the printing techniques are cost-effective and allow mass production, which make them still interesting.

L'alliage Si-Ge est utilisé depuis de nombreuses années dans les modules thermoélectriques dans les sondes spatiales de la NASA. Ils convertissent la chaleur résultant de la désintégration radioactive de matériaux riches en un ou plusieurs radio-isotopes en électricité. Cet alliage est performant à haute température (à partir de 700 °C), c'est pourquoi il trouve également un fort intérêt dans l'industrie automobile. De nombreuses recherches dans ce secteur s'orientent vers la thermoélectricité, notamment vers des modules fonctionnant à haute température pour permettre la réduction de consommation de carburant.La meilleure composition de l'alliage en thermoélectricité est Si0,8Ge0,2. Le facteur de mérite réduit (ZT) de ces matériaux est généralement proche de 0,75 et de 0,45 à 700 °C pour les types n et p respectivement. Le germanium étant très onéreux, la composition retenue dans cette étude est Si0,92Ge0,08. Pour améliorer les performances de la composition choisie et se rapprocher de celles de la meilleure composition, la voie retenue est l'incorporation de nanoinclusions à base de siliciures de molybdène dans le matériau, permettant la diminution de la conductivité thermique.L'alliage Si-Ge est synthétisé par mécanosynthèse, et densifié par SPS. Les dopants utilisés sont le phosphore et le bore pour les types n et p respectivement. Le taux de dopage optimal est de 0,7 %. Ainsi, les ZT obtenus à 700 °C sont égaux à 0,7 et 0,5 pour les types n et p respectivement. La nature des inclusions stables dans la matrice est déterminée par la méthode CalPhad qui permet l'obtention du diagramme ternaire Mo-Si-Ge. La phase MoSi2 apparait alors comme étant la seule phase stable dans la matrice Si0,92Ge0,08. La fraction volumique optimale de molybdène est de 1,3 % lorsque les matériaux sont densifiés à 1280 °C. Le ZT obtenu est supérieur à 1 à 700 °C pour le type n, et proche de 0,8 pour le type p. L'ajout de nanoinclusions a permis d'augmenter les performances de 43 % et de 60 % à 700 °C. / Si-Ge alloys has been used for many years in the thermoelectric modules in the NASA space probes in which they convert heat produced by the radioactive decay of a heat source into electricity. This alloy is effective at high temperature (from 700 °C), so it is also a strong interest in the automotive industry. The strong incentive in this area to reduce fuel consumption leads researchers to develop thermoelectric modules that can operate at high temperatures. The composition at which SiGe alloys are the most thermoelectrically efficient is Si0.8Ge0.2. Their figure of merit (ZT) is generally close to 0.75 and 0.45 at 700 °C for type n and p respectively. As Germanium is very expensive, this study aims to develop a Si0.92Ge0.08 alloy that can compare to the existing Si0.8Ge0.2 alloys. To get to a higher level of performance, the thermal conductivity of the chosen composition has to be decreased, which is done by incorporating molybdenum silicides in the Si0.92Ge0.08 alloys.The Si-Ge alloy was synthesized by mechanical alloying, and sintered by SPS. The dopants used are phosphorous and boron for the n and p types respectively. The optimal doping level is 0.7%. ZT obtained for Si0.92Ge0.08 base alloys at 700 °C are equal to 0.7 and 0.5 for n and p types respectively. The nature of stable inclusions in the matrix has been determined by the CALPHAD method to obtain the ternary diagram Mo-Si-Ge. Then, the MoSi2 phase appears to be the only stable phase in the matrix Si0.92Ge0.08. The optimum volume fraction of molybdenum was 1.3% when the materials are sintered at 1280 °C. Therefore, the ZT obtained is higher than 1 at 700 °C for n-type and close to 0.8 for p-type. Adding nanoinclusions has increased performance by 43% (n-type) and 60% (p-type) at 700 °C.

Les travaux présents ici portent sur l’étude et la prospection de matériaux ferroiques. Cette étude consiste en une approche revêtant plusieurs aspects que sont la chimie du solide, la physique du solide et la science des matériaux. Deux parties sont développées, avec deux approches différentes. La première se concentre sur les liens entre composition/structure/propriétés dans des matériaux de la famille des TTB dérives de Ba2NdFeNb4O15 à travers l’étude de solutions solides à base de Li et l’étude de l’impact des différents paramètres de synthèse sur la nature de l’anomalie diélectrique mesurées sur pastilles densifiées. La mise en évidence de modulation structurale dans cette famille de matériaux semble être en lien direct avec l’observation des variations de propriétés diélectriques. L’utilisation de diffraction électronique notamment permet la mise en évidence de ces modulations structurales et leur évolution en température. Dans une seconde partie, l’approche consiste à utiliser le Spark Plasma Sintering (SPS) comme technique de densification pour des matériaux dits “fragiles” mais aussi d’explorer des propriétés diélectriques jusqu’alors inaccessibles, sur matériaux massifs. Le développement de la technique SPS à basse température permet ainsi non seulement de densifier à basse température des matériaux fragiles, mais aussi d’obtenir des phases inaccessibles dans des conditions de températures similaires par traitement thermique conventionnel. De même, l’obtention de céramique moléculaire de très haute densité a pu être réalisée, malgré des températures de décomposition extrêmement faible (100 ˚C). / The present work focuses on the prospection and understanding study of ferroic materials. It consists in a multiple aspect approach, including materials chemistry, materials physics and materials processing. Two parts compose this work, with two different approaches. The first one focuses on the links between composition, structure and properties in materials belonging to the TTB family, more specifically derived from Ba2NdFeNb4O15, through the exploration of Li containing solid solutions, and the impact of synthesis parameters on measured dielectric anomalies on dense samples. The observation of structural modulation in these materials seems to be closely related to the observation of dielectric anomalies variations. Using electron diffraction techniques allowed the evidence of such anomalies and the following of their thermal evolution. In a second part, the approach consists in using Spark Plasma Sintering (SPS) as a densification technique for so called “fragile” materials but also explore dielectric properties impossible to experimentally measure thus far. Developing low temperature SPS technique not only allows to densify ceramics at low temperatures fragile materials, but also to obtain inaccessible phases in similar temperature conditions using conventional thermal treatments. Moreover, sintering of molecular ceramic at very high density was possible, even if its decomposition temperature is extremely low (100 ˚C).

Les assemblages multicouches polymère-métal, combinant la faible densité du polymère à la résistance du métal, se présentent comme une solution à fort potentiel pour répondre aux problématiques d’allégement de structure dans le secteur des transports. Plus particulièrement, ces travaux s’intéressent à l’élaboration de multicouches basés sur l’utilisation de polymères thermoplastiques thermostables associés à un alliage d’aluminium via un procédé de la métallurgie des poudres appelé « Spark Plasma Sintering » (SPS). Dans un premier temps, la mise en forme par SPS du polymère seul a été étudiée. Les influences des paramètres SPS tels que la température, la pression appliquée et le temps de maintien sur les caractéristiques structurales et les propriétés mécaniques du polyétheréthercétone (PEEK) ont été déterminées au moyen d’un plan d’expérience. Cette étude a permis de proposer des mécanismes de frittage et de mettre en évidence le rôle complexe joué par la pression sur la structure cristalline. Ensuite, le développement des assemblages, sans colle, d’un polyimide ou PEEK associé avec l’aluminium a été considéré. Une approche expérimentale a été mise en place, dans le but d’améliorer l’adhésion entre les deux matériaux. Des traitements de surface appliqués à l’aluminium visant à augmenter l’ancrage mécanique et la compatibilité chimique ont été testés. Le renforcement du polymère afin de limiter sa dilatation thermique a également été abordé. Les contributions de chacun des facteurs sont discutées sur la base de mesures d’adhérence et de caractérisations microstructurales. Cette stratégie a permis d’obtenir des multicouches avec une forte résistance à l’interface. / Polymer/metal multilayer assemblies, combining the low density of the polymer with the strength of the metal, are considered to be of great interest for high-demand engineering applications, especially in the transportation industries where the lightweighting issues are predominant. Keeping this in mind, the present study deals with the development of this kind of assembly, using thermostable thermoplastic polymers associated with an aluminum alloy by means of a powder metallurgy process: the “Spark Plasma Sintering” (SPS) technology. As the first part of this work, the sintering of the polymer was considered. The effects of SPS parameters such as temperature, pressure, and dwell time on mechanical properties of a PolyEtherEtherKetone (PEEK) were investigated thanks to a design of experiment. This study allowed to determine the mechanisms of polymer’s consolidation and the intricate role of pressure on the PEEK crystallinity was examined with particular attention. Then, the development of the assembly, without adhesive part, composed of both polymer (polyimide or PEEK) and aluminum alloy was considered. An approach was set up to improve the compliance between these dissimilar materials comprising: surface treatments on aluminum in order to enhance their mechanical anchoring and their chemical compatibility, as well as polymer reinforcement with the aim of reducing its thermal expansion. The efficiency of each solution is discussed based on microstructural and mechanical characterizations. This approach enabled to process multilayer assemblies with a significant strength at the interface.