Techn. Universiẗat, Diss., 2004--Darmstadt.

The aim of this master thesis deals with the optimization of the preparation of thin hydrogel films based on polyvinyl alcohol (PVA) with the possibility of incorporating suitable additives (polyelectrolytes, plasticizers, etc.) into the structure of the prepared film to modify its properties. DEAE-Dextran hydrochloride and polyglutamic acid (PGA) were used as polyelectrolytes. The basic characterization of the properties was performed on modified films, which were compared with pure PVA films. The films were characterized by thickness, swelling ability, barrier properties, tensile properties, specific surface area, antimicrobial tests, and thermogravimetric analysis. The swelling ability of PVA/PGA films was very high, which may be a disadvantage for their use in the packaging industry. Swelling increases the amount of water in the matrix of the PVA film, what leads to a higher growth of microorganisms and to degradation of thin film. The water vapor transmission rate was greatly affected by the addition of a plasticizer. The small specific surface area of the films indicates a smooth surface that promotes good barrier properties. Films with the addition of a plasticizer showed relatively good mechanical properties. The values of tensile strength, elongation and elastic modulus were comparable to commercially available films such as polypropylene (PP) or polyethylene (PE). Based on all experiments, PVA, PVA/DEAEDextran films and their variants with the addition of glycerol as a plasticizer were evaluated as the best candidates for the use of these films as packaging materials. The follow-up work could be dealing with the optimization of PVA films for oxygen permeability. Furthermore, the possibilities of using these films in the packaging industry based on the relative humidity of the environment, could be defined as other interesting area of future research.

Polymerem impregnované cementové materiály představují zajímavou a perspektivní alternativu klasických portlandských cementových past. Hlavním zástupcem těchto materiálů jsou macrodefect-free (MDF) kompozity, složené z anorganického pojiva a organického polymeru. I přes řadu vynikajících mechanických vlastností je plné zavedení MDF kompozitů na trh omezené především z důvodu jejich relativně nízké odolnosti vůči vlhkosti. Jednou z možností jak zvýšit odolnost výsledného MDF vůči vlhkosti je „in situ“ síťování polymeru. V této práci byla připravena počáteční série MDF kompozitů na bázi hlinitanového cementu a polyvinylalkoholu se třemi typy organo-titanátových síťovacích činidel (Tyzory). Efekt modifikace MDF kompozitů byl hodnocen na základě zkoušek pevnosti v tahu za ohybu po uložení materiálů v různých vlhkostních podmínkách.

Im Rahmen des Transferprojektes T01 „Textilbeschichtung mit hochviskosen Massen“ des Sonderforschungsbereiches 532 (SFB 532) wird die Realisierung und Bewertung eines integrierten Beschichtungskonzeptes zur nachhaltigen Verbesserung der Tragfähigkeit von textilbewehrten Betonbauteilen an der RWTH Aachen University untersucht. Dazu wird eine neue Auftragstechnik für hochviskose Beschichtungsmassen entwickelt, die eine vollständige Penetration von Multifilamentgarnen mit großen Garntitern und einer hohen Anzahl an Filamenten in textilen Gelegen erzielt. Des Weiteren werden aktive Beschichtungsmassen auf der Basis von Polyvinylalkohol-Zement-Compositen, die eine homogene Anbindung aller Einzelfilamente an die Zementmatrix ermöglichen, erforscht.

Eine Möglichkeit der kostensenkenden Technologieentwicklung bei der Herstellung von Geschirrporzellan stellt das gleichzeitige Brennen von Scherben und Glasur im Einmal-Schnellbrand dar. Der Einsatz eines Gemisches aus organischen und anorganischen Additiven bringt dabei optimale Verarbeitungseigenschaften der Porzellangranulate hervor. Feinere Porzellangranulate sind in Verbindung mit einem Mindestanteil an geeigneten organischen Bindern industriell verpressbar. Daraus hergestellte Flachgeschirrartikel weisen ausreichende Gefügefestigkeiten und –dichten im ungebrannten Zustand und während des Brandes auf. Der Glasurauftrag erfolgte durch Spritzen. Eine spezielle Brennkurve ermöglicht eine ausreichend lange Entgasungsperiode vor dem Dichtsintern des Scherbens und dem Ausfließen der Glasur. Das Einsetzen einer Feuerpolitur nach Beenden der Haltezeit bei maximaler Brenntemperatur führt zu einer Verbesserung der Glasuroberflächenqualität.

This diploma thesis investigates the suitability of relaxation tests as a part of complex characterization of hydrogel materials using classical rheology methods. With respect to the current research, creep and three interval thixotropy tests were taken into account. For them, general optimization was done aiming to find an ideal parameter settings. The optimization was performed using physically crosslinked agarose (AG) hydrogel and the tuned tests were also applied to two more samples: hyaluronan (HyA) and polyvinyl alcohol (PVAl) gel. These materials were selected due to their mutually different crosslinking principle. The experiments showed, the AG gel proved to have the best ability to recover after deformation of all studied samples. On the other hand, the HyA gel relaxed the worst. Although the final results of both tests were comparable, the regeneration process itself was different. Hence, the complex relaxation characteristics cannot be described using one of the performed tests alone and both the creep and three interval thixotropy tests have great importance in the scope of complex relaxation behaviour. The obtained results may lead to more precise description of deformation and relaxation, which are frequent phenomena occurring during treatment and application of hydrogel materials.

The subject of the diploma thesis is the preparation of macro-defect-free (MDF) composites based on calcium-aluminate cement and organic polymer polyvinylalcohol. Attention focused on the optimization of the dose, the degree of hydrolysis and molecular weight of the polymer with respect to the heat resistance of the material. Thermal degradation of polyvinyl alcohol leads to changes in the structure of MDF composite. The study was mainly focused on the characteristics of polyvinyl alcohol dosage associated with the resultant mechanical properties of the material. During the work were monitored for changes in the mechanical properties of samples were cured at 60 °C and subsequently fired at 180 °C, 600 °C, 1000 °C and 1400 °C. It was tested in flexural strength, heat microscopy, TGA-DTA-EGA and SEM analysis.

The subject of the thesis is to improve the moisture resistance of MDF (macro-defect-free) composites prepared on the basis of aluminous cement and polyvinyl alcohol. These materials are characterized by the absence of defects in the structure and high mechanical performance. These features make MDF composites a promising type of material that could be used in the future for construction purposes. The basic deficiency of MDF composites is insufficient resistance to water or moisture, accompanied by a significant decrease in strength. Therefore, this work deals with increasing of moisture resistance using organotitanate agent and modification of the polymer. Two types of polyvinyl alcohols differing in hydrolysis degree and degree of the polymerization has been modified. Based on the results of the measurement the effect of storage conditions on the properties and structure of prepared MDF composites was observed. The characterization of MDF composites were realized by measurement of flexural strength in bending, scanning electron microscopy with EDS analysis, TG-DTA-EGA, water absorption and consequently the porosity of all prepared MDF composites.

This diploma thesis deals with preparation and characterization of aqueous solutions of polyvinyl alcohol suitable for electrospinning. In the theoretical part method of electrospinning is described, including parameters which influence this process. Literary research also includes a chapter about rheology, which deals with the rheological properties of polymers, specifically PVA. The experimental part describes the preparation and rheological study of of aqueous solutions of polyvinyl alcohol, which were then spun. The morphology of prepared nanofibers was studied by using scanning electron microscopy (SEM). The effect of molecular weight, the solvent, concentration of solution, rheological properties, electrical conductivity and surface tension on the spinability, diameter and morphology of nanofibers is discussed.

Eine Möglichkeit der kostensenkenden Technologieentwicklung bei der Herstellung von Geschirrporzellan stellt das gleichzeitige Brennen von Scherben und Glasur im Einmal-Schnellbrand dar. Der Einsatz eines Gemisches aus organischen und anorganischen Additiven bringt dabei optimale Verarbeitungseigenschaften der Porzellangranulate hervor. Feinere Porzellangranulate sind in Verbindung mit einem Mindestanteil an geeigneten organischen Bindern industriell verpressbar. Daraus hergestellte Flachgeschirrartikel weisen ausreichende Gefügefestigkeiten und –dichten im ungebrannten Zustand und während des Brandes auf. Der Glasurauftrag erfolgte durch Spritzen. Eine spezielle Brennkurve ermöglicht eine ausreichend lange Entgasungsperiode vor dem Dichtsintern des Scherbens und dem Ausfließen der Glasur. Das Einsetzen einer Feuerpolitur nach Beenden der Haltezeit bei maximaler Brenntemperatur führt zu einer Verbesserung der Glasuroberflächenqualität.