This thesis explores the heat transfer characteristics of a packed bed thermal energy storage device through the development of a 3D model in COMSOL Multiphysics. The model is based on a laboratory-scale device consisting of an aluminum box filled with sand, which acts as the thermal storage medium. The medium is heated using two resistance heaters that are embedded into the sand. The heaters are raised to approximately 500°C during the experiment. Three thermocouples placed in the sand record the temperature during charging, thus generating a time-dependent temperature curve at three points. The model simulates this experimental system, and the resulting temperature distribution is compared to the experimental data to assess the model validity. To determine the temperature throughout the storage system at all times, the model solves the heat equation. The density and heat capacity of the sand are measured and added to the model. The model uses the effective medium technique to estimate the thermal conductivity of the sand. A secondary model is developed in Excel to calculate the effective thermal conductivity using twelve different correlations, and the results are compared. The Zehner-Bauer correlation with an added Damköhler radiation term predicted an effective thermal conductivity of 0.218 W/(m·K) at 25°C and 0.451 W/(m·K) at 500°C, with slightly exponential growth due to the influence of thermal radiation. When these values for conductivity are applied to the COMSOL model, there is strong agreement (average percent error < 5%) with the experimental temperature distributions. A parametric study is performed, and shows that increasing grain size and emissivity could increase the thermal conductivity by making use of the exponential growth of thermal radiation. The model serves as a design and learning tool, and a starting point for improving the performance of the thermal energy storage system. / Detta examensarbete undersöker värmeöverföringsegenskaperna hos en termisk energilagringsenhet med packad bädd genom utveckling av en 3D-modell i COMSOL Multiphysics. Modellen är baserad på en enhet i laboratorieskala som består av en aluminiumlåda fylld med sand, som fungerar som det termiska lagringsmediet. Mediet värms upp med hjälp av två motståndsvärmare som är inbäddade i sanden. Värmeelementen höjs till ca 500°C under experimentet. Tre termoelement placerade i sanden registrerar temperaturen under laddningen och genererar på så sätt en tidsberoende temperaturkurva i tre punkter. Modellen simulerar detta experimentella system, och den resulterande temperaturfördelningen jämförs med experimentella data för att bedöma modellens giltighet. För att bestämma temperaturen i hela lagringssystemet vid alla tidpunkter löser modellen värmeekvationen. Sandens densitet och värmekapacitet mäts och läggs till i modellen. Modellen använder den effektiva mediumtekniken för att uppskatta sandens värmeledningsförmåga. En sekundär modell utvecklas i Excel för att beräkna den effektiva värmeledningsförmågan med hjälp av tolv olika korrelationer, och resultaten jämförs. Zehner-Bauer korrelationen med en tillagd Damköhler strålningsterm förutsade en effektiv värmeledningsförmåga på 0,218 W/(m·K) vid 25°C och 0,451 W/(m·K) vid 500°C, med en något exponentiell tillväxt på grund av påverkan från värmestrålning. När dessa värden för konduktivitet tillämpas på COMSOL-modellen finns det en stark överensstämmelse (genomsnittligt procentuellt fel < 5%) med de experimentella temperaturfördelningarna. En parametrisk studie har utförts som visar att ökad kornstorlek ock emissivitet kan öka värmeledningsförmågan genom att utnyttja den exponentiella tillväxten av värmestrålning. Modellen fungerar som ett design- och inlärningsverktyg och som en utgångspunkt för att förbättra prestandan hos det termiska energilagringssystemet.

<p>  </p> <p>Water scarcity is a global problem impacting a majority of the world population. A significant proportion of the global population is deprived of clean drinking water, an impact felt by the rural as well as urban population. Saltwater desalination provides an attractive option to produce clean water. Some technologies to generate potable water include reverse osmosis (RO), multi-stage flash distillation (MSF), vapor compression distillation and multi-effect distillation (MED). Distillation plants such as those in MED often have falling-film evaporators operating at low energy conversion efficiency and hence distillation is performed over multiple stages (or effects). Porous materials can be utilized as evaporators in such plants with the objective of leveraging their superior efficiency. This can potentially decrease the number of effects over which distillation occurs. However, evaporation of high-salinity salt solution eventually results in salt precipitation which can cause fouling and induce structural damages, especially if the precipitates appear within the porous medium. Crystallization-induced structural damages are also of significant concern to building materials and for their role in weathering of historical monuments. It is thus crucial to understand the mechanisms governing salt precipitation in a porous medium.</p> <p>Transport of solute in such a medium is either driven by flow of the solution (advection) or by concentration gradients (diffusion). The dynamics of solute transport is further complicated due to the involvement of a reaction term accounting for any salt precipitation. The relative strengths of these driving forces determine the solute transport behavior during an evaporation-driven process. The wide-scale applications of solute transport and its complicated nature warrant investigation, both experimental and theoretical, of the dependence of solute transport and the subsequent precipitation on the operating conditions and the properties of the porous medium.</p> <p>This dissertation first focuses on developing a novel modeling framework for evaluating the transient behavior of the solute mass fraction profile within the domain of a one-dimensional porous medium, and extending its capability to predict the formation of salt precipitate in the medium.  Experimental investigations are then performed to study the formation of precipitate on sintered porous copper wicks of different particle-size compositions, and developing a mechanistic understanding of the governing principles.</p> <p>A numerical modeling framework is developed to analyze evaporation-driven solute transport. Transient advection-diffusion equations govern the salt mass fraction profile of the solution inside the porous medium. These governing equations are solved to obtain the solute mass fraction profile within the porous medium as well as the effloresced salt crust. Further accounting for precipitation allows a study of the formation and growth of efflorescence and subflorescence. Crystallization experiments are performed by allowing a NaCl solution to evaporate from a porous medium of copper particles and the subflorescence trends predicted by the model are validated. The modeling framework offers a comprehensive tool for predicting the spatio-temporal solute mass fraction profiles and subsequent precipitation in a porous medium.</p> <p>The dependence of efflorescence pattern on the properties of a porous medium is also investigated. Efflorescence patterns are visually observed and characterized on sintered copper particle wicks with spatially unimodal and bimodal compositions of different particle sizes. Efflorescence is found to form earlier and spread readily over a wick made from smaller particles, owing to their lower porosity, while it is limited to certain areas of the surface for wicks composed of the larger particles. A scaling analysis explains the observed efflorescence patterns in the bimodal wicks caused by particle size-induced non-uniform porosity and permeability. The non-uniformity reduces the advective flux in a high-permeability region by diverting flow towards a low-permeability region. This reduction in advective flux manifests as an exclusion distance surrounding a crystallization site where efflorescence is not expected to occur. The dependence of this exclusion distance on the porosity and permeability of the porous medium and the operating conditions is investigated. A large exclusion distance associated with the regions with bigger particles in the bimodal wicks explains preferential efflorescence over the regions with smaller particles. This novel scaling analysis coupled with the introduction of the exclusion distance provides guidelines for designing heterogeneous porous media that can localize efflorescence.</p> <p>Additionally, droplet interactions with microstructured superhydrophobic surfaces as well as soft surfaces were investigated during the course of this dissertation, separate from the above investigations. These investigations involve the interplay of surface energies with electrical or elastic energies and are studied both experimentally and through theoretical models, and therefore are retained as additional chapters in the thesis as being of relevant interest.  Electrowetting experiments are performed on superhydrophobic surfaces with re-entrant structures to study their resilience to the Cassie-to-Wenzel transition. The deformation of soft surfaces caused by forces exerted by microscale droplets is studied and the resulting interaction between multiple droplets is explored. </p>

Cette thèse concerne l’existence et la régularité de solutions d’équations non-linéaires elliptiques, d’équations paraboliques et d’équations de Hesse avec mesures, et les critères de l’existence de solutions grandes d’équations elliptiques et paraboliques non-linéaires. / This thesis is concerned to the existence and regularity of solutions to nonlinear elliptic, parabolic and Hessian equations with measure, and criteria for the existence of large solutions to some nonlinear elliptic and parabolic equations.