The horizontal shear strength of the interface between prestressed concrete hollow core slabs and cast-in-place concrete topping slabs was evaluated through a set of 24 push-off experiments. The push-off test specimens featured segments of dry-mix and wet-mix hollow core slabs with a variety of surface treatments including machine finished, sandblasted, broom roughened, rake roughened and grouted. A cast-in-place slab was poured on top of the hollow core specimens to form a 15 inch by 15 inch interface between the two materials. Results indicate the average horizontal shear strength of the push-off specimens was 227 psi. Higher shear strength and slip capacity was observed in specimens that were broom roughened in the direction transverse to the applied shear force and in grouted dry-mix specimens. Specimens with machine finished surfaces had lower average horizontal shear strength than those with intentionally roughened surfaces, but still exceeded the shear strength of 80 psi specified in the ACI 318-08 code. A method to comparatively quantify the surface roughness of the hollow core slabs with different surface treatments was adapted from an existing ASTM standard for pavements. This standard specifies the procedure to determine mean texture depth that can be correlated to horizontal shear strength of the push-off specimens. Analytical studies were also performed to estimate the maximum horizontal shear stresses that can be expected in composite hollow core slabs under normal construction conditions. A finite element model was developed to observe the behavior of the horizontal shear failure mode for composite hollow core slabs.

Use of composite steel construction with precast hollow core slabs is now popular in the UK, but the present knowledge in shear capacity of the headed shear studs for this type of composite construction is very limited. Currently, all the information is based on the results obtained from experimental push-off tests. A finite element model to simulate the behaviour of headed stud shear connection in composite beam with precast hollow core slabs is described. The model is based on finite element method and takes into account the linear and non-linear behaviour of all the materials. The model has been validated against the test results, for which the accuracy of the model used is demonstrated. Parametric studies showing the effect of the change in transverse gap size, transverse reinforcement diameter and in-situ concrete strength on the shear connection capacity are presented.

This paper is concerned with the behaviour of beam ¿ column connections of steel ¿ concrete composite beams with precast hollow core slabs. Experiments were carried out to investigate the joint rotation characteristics and ultimate moment capacity of these connections. Details of the test specimens, instrumentation, test set-up and test procedures are described. Results obtained for the connection moment capacity, rotation capacity and failure modes are presented. It is found that through proper design and detailing, these simple steel connections display the characteristics of a semi-rigid connection with very little extra cost.

This paper evaluates the effective width of composite steel beams with precast hollowcore slabs numerically using the finite element method. A parametric study, carried out on 27 beams with different steel cross sections, hollowcore unit depths and spans, is presented. The effective width of the slab is predicted for both the elastic and plastic ranges. 8-node three-dimensional solid elements are used to model the composite beam components. The material non-linearity of all the components is taken into consideration. The non-linear load-slip characteristics of the headed shear stud connectors are included in the analysis. The moment-deflection behaviour of the composite beams, the ultimate moment capacity and the modes of failure are also presented. Finally, the ultimate moment capacity of the beams evaluated using the present FE analysis was compared with the results calculated using the rigid – plastic method.

No

No description available.

Concrete pavements are a suitable alternative for high-traffic volume roads, concentrated loads and roads exposed to severe weather conditions. In Sweden, among other reasons, the scarcity of concrete pavements is attributed to the need for more national knowledge and expertise in the field. The most recent concrete pavement was constructed seventeen years ago in Uppsala. Concrete pavements are renowned for their longevity and durability. Jointed plain concrete pavements (JPCP) are the most frequent type of concrete pavements. However, it is important to note that the joints in concrete pavements are critical components that can lead to various distresses, necessitating rehabilitation. Rehabilitating concrete pavements is particularly challenging in areas with heavy traffic and requires substitute routes because of the imperative to maintain traffic flow during construction. Developing effective detours might involve significant alterations to the existing routes or building temporary roads, which entails substantial cost investment and time consumption. A literature review has been conducted to study the available methods that can be used to repair concrete pavements. The strategy for selecting a repair technique is based on rehabilitating the concrete pavement within a short work window, deterring traffic congestion and ensuring the long service life of the pavements. The study showed that the precast concrete technology based on the precast slab is a promising technology that effectively shortens the lane closure for repairing damaged pavements and produces durable pavements, thereby extending the service life of pavements. However, the construction or rehabilitation cost of concrete pavement using precast slabs is 1.6 to 4 times higher than that of conventional cast-in-place concrete. Therefore, rehabilitation using precast slabs is inappropriate for low-traffic roads and temporary routes. Joints are crucial for the rehabilitation of concrete pavements with precast slabs. The structural performance of concrete pavement is, however, greatly affected by the joints, as the presence of joints creates a discontinuity between adjacent slabs and thus diminishes the load transfer to the abutting slab. To maintain the structural integrity of the pavement system, dowel bars are used at the transverse joints. A numerical study has been conducted to evaluate the influence of various dowel-related parameters on the interaction between adjacent concrete slabs. The study revealed that the dowel bar’s position, mislocation and diameter had an obvious effect on joint efficiency, while the bond between the concrete slab and the dowel bar slightly affected the load transfer efficiency. It was also investigated that the dowel bar’s intended performance, i.e., load transfer efficiency, was reduced as the joint gap between adjacent slabs increased. / Betongbeläggningar är ett lämpligt alternativ för högtrafikerade vägar, koncentrerad belastning och vägar utsatta för svåra väderförhållanden. I Sverige är betongvägar sällsynta vilket bl.a. beror på brist på kunskap och kompetens. Den senaste betongvägen byggdes för sjutton år sedan i Uppsala.Betongbeläggningar är kända för sin långa livslängd och hållbarhet. Den vanligaste typen av betongvägar är fogade, oarmerade betongbeläggningar. Ändå är det viktigt att notera att fogarna i betongbeläggningar är kritiska komponenters om kan leda till olika olägenheter, vilket kräver rehabilitering. Att rehabilitera betongbeläggningar är särskilt utmanande i områden med intensiv trafik som kräver ersättningsvägar på grund av nödvändigheten att upprätthålla trafikflödet under reparationsarbetena. Att ta fram en effektiv omledning av trafiken kan innebära antingen väsentliga förändringar och förlängningar av befintliga rutter eller byggande av tillfälliga vägar, vilket medför betydande kostnadsinvesteringar och tidsåtgång. En litteraturöversikt har genomförts för att studera de tillgängliga metoderna som kan användas för att reparera betongbeläggningar. Strategin för valet av reparationsmetod bygger på att rehabilitera betongbeläggningen inom ett kort arbetsfönster, förhindra trafikstockningar och säkerställa lång livslängd för beläggningen. Studien visade att förtillverkade betongplattor är en lovande metod som effektivt förkortar avstängningen av körfält för att reparera skadad beläggning och producerar hållbara betongbeläggningar med lång livslängd. Rehabiliterings kostnaden för betongbeläggning med prefabricerade plattor är emellertid 1,6 till 4 gånger högre än den för konventionell platsgjuten betong. Därför är rehabilitering med förtillverkade betongplattor olämplig för vägar med låg trafik och temporära rutter. Fogar är vidare nödvändiga vid reparation med förtillverkade betongplattor.Betongbeläggningens strukturella prestanda påverkas dock kraftigt av fogar, eftersom förekomsten av fogar skapar en diskontinuitet mellan intilliggande plattor och därmed minskat lastöverföringen till den angränsande plattan. För att upprätthålla den strukturella integriteten hos beläggningssystemet används dymlingar i de tvärgående fogar. En numerisk studie har genomförts med olika parametrar för att utvärdera dymlingens inverkan på fogens effektivitet. Studien visade att dymlingens position, felplacering och diameter har en tydlig inverkan på fogens effektivitet, medan vidhäftningen mellan dymling och betongplatta enbart verkar ha en marginell inverkan på fogens effektivitet. Studien visade också att dymlingens prestanda, dvs. lastöverföringsförmågan, minskade då fogöppningen eller glappet mellan två närliggande plattor ökade. / <p>QC 240207</p>

The Precast/Prestressed Concrete Institute (PCI) is the technical institute for precast/prestressed concrete industry. The plant involves activities such as placing high tensile steel strings inside the concrete products before they harden. This process needs the strings to be "stressed" hydraulically with high tension, which provides possibility of breaking the strand. Hence, employees may face a severe injury around the stressing bed. As various activities take place on the plant at the same time, employees must follow certain safety protocols while being around the plant. Another safety concern on the precast plant is silica exposure. Occupational Safety and Health Administration (OSHA) has provided various guidelines and tools to minimize silica exposure. Employees need to be careful and follow these safety protocols, otherwise it may lead to severe lung disease. Thus, employees need the appropriate safety training which will motivate them to follow safety protocols rigorously. The Bayesian Network (BN) methodology helps analyze plant structure to understand potential risk factors and causes that can be fixed by the employer paying more attention. The current traditional training methods such as videos, PowerPoint slides, or on-paper training, are not as effective in conveying the severity of the risky situations. This research focuses on precast plant activities while trying to identify the factors affecting plant safety. The current results suggest that using the BN study for the factors, such as stressing, chipping, leg injuries, tripping, and suspended loads, that may cause accidents or affect plant safety have a major impact on overall plant safety. Further sections of the dissertation discuss Fault Tree Analysis for risk assessment. It is observed that the BN study outperforms the risk assessment. Improvisation in safety protocols associated with these factors will help mitigate overall plant risks. In addition, study includes the development of immersive training methods and comparison of the immersive method to current safety training methods. Virtual Reality (VR) training module provides significant evidence to improvement in motivation level compared to traditional training. Knowledge gain concerning the safety protocols proves to be increasing for employees after the VR training method compared to the traditional training methods.

No description available.

No / The chapter describes the ongoing work on modeling the semi-rigid composite beam-column connections of composite beams with precast hollow core slabs. Using the finite element (FE) software ABAQUS, a three-dimensional (3D) model of a composite joint is set up. The technique of simulating bolt force, endplate, concrete elements, reinforcement, and shear connectors, and the interaction between slabs and steel beams is presented in the chapter. Preliminary results on the steel joint and simplify composite joint are also presented in the chapter. FE model for the bare steel joints and the simplified composite joints are presented, and the result of the simplified composite model showed good agreement with the experimental result but with lower joint stiffness. Further work on the full finite element model of composite joints is still going on.