This paper describes the finite element modelling of steel beams acting compositely with proprietary precast hollow core slabs. A companion paper (Lam D, Elliott KS, Nethercot DA. Experiments on composite steel beams with precast hollow core floor slabs. Proceedings of the Institution of Civil Engineers: Structures and Buildings 1999; in press [1]) reports results of full scale bending tests and compression slab tests. The finite element package ABAQUS was used to extend the scope of the experimental work, by first demonstrating that a 2-dimensional plane stress analysis is sufficiently accurate, providing that the correct material input data and shear stud characteristics obtained from isolated push-off tests are used. The FE results are within 5% of the experimental results. An extensive parametric study was carried out to investigate the flexural behaviour of composite beams with variations in transverse reinforcement ratio, stud spacing and steel UB section.

This paper describes the 3-dimensional finite element modelling of composite connection with steel beams and precast hollow core slab. A finite element model to simulate the structural behaviour of the composite beam was described and was used to study the behaviour of a wide range of composite connections to gain a better understanding of the structural behaviour especially the moment¿rotation characteristic of the connections. Parametric studies were carried out to investigate the structural behaviour with variations in: size of the beam, thickness of the endplate, thickness of column web, depth of precast hollow cored slab and stud spacing. Through the parametric study, the structural behaviour of the composite connection has been discussed in detail, and recommendations for the design purpose has been made.

Full-depth precast concrete panels offer an efficient alternative to traditional cast-in-place concrete for replacement or new construction of bridge decks. Research has shown that longitudinal post-tensioning helps keep the precast bridge deck in compression and avoid problems such as leaking, cracking, spalling, and subsequent rusting on the beams at the transverse panel joints. Current design recommendations suggest levels of initial compression for precast concrete decks in a very limited number of bridge configurations. The time-dependent effects of creep and shrinkage in concrete and relaxation of prestressing steel complicate bridge behavior, making the existing recommendations for post-tensioning in precast deck panels invalid for all bridges with differing girder types, sizes, spacings, and span lengths. Therefore, the development of guidelines for levels of post-tensioning applicable to a variety of bridge types is necessary so designers may easily implement precast concrete panels in bridge deck construction or rehabilitation. To fulfill the needs described, the primary objective of this research was to determine the initial level of post-tensioning required in various precast concrete bridge deck panel systems in order to maintain compression in the transverse panel joints until the end of each bridge's service life. These recommendations were determined by the results of parametric studies which investigated the behavior of bridges with precast concrete decks supported by both steel and prestressed concrete girders in single spans as well as two and three continuous spans. The three primary variables in each parametric study included girder type, girder spacing, and span length. The age-adjusted effective modulus method was used to account for the ongoing effects of creep and shrinkage in concrete. Results from the Mathcad models used in the parametric studies were confirmed through comparison with results obtained from finite element models generated in DIANA. Initial levels of post-tensioning for various bridge systems are proposed based on the trends observed in the parametric studies. The precast decks of the simple span bridges with steel girders and the one, two, and three span bridges with prestressed concrete girders needed only 200 psi of initial post-tensioning to remain in compression under permanent and time-dependent loads throughout each bridge's service life. The precast decks of the two and three span continuous bridges with steel girders, however, needed a significantly higher level of initial compression due to the negative moments created by live loads. / Master of Science

Concrete technology has been in changeful evolution since the Roman Empire time. It is remarkable that the technological progress became of higher magnitude from the second part of the XX Century. Advances in the development of new cements, the appearance of the fibers as a reinforcement for structural applications, and specially the grand progress in the field of the water reducing admixtures enabled the emergence of several types of special concretes. One of the lasts is the Ultra High Performance Fiber Reinforced Concrete (UHPFRC), which incorporates advances of the Self-Compacting Concrete (SCC), Fiber-Reinforced Concrete (FRC) and Ultra High Strength Concrete (UHSC) technology. This exclusive material requires a detailed analysis of the components compatibility and a high control of the materials and processes. Mainly patented products have been used for the few structural elements carried out so far today, but the costs makes doubtful the development of many other potential applications. In accordance with the previously explained, a simplification of the UHPFRC components and processes is needed. This becomes the first main goal of this Ph.D. thesis, which emphasizes in the use of local available components and simpler mixing processes. Moreover, the singular properties of this material, between ordinary concrete and steel, allow not only the realization of slenderer structures, but also the viability of new concepts unthinkable with ordinary concrete. In this field is focused the second part of the Ph.D. thesis, which develops a bolted connection system between UHPFRC elements. This research summarizes, first of all, the subfamilies belonging to the HPC-UHPC materials. Afterwards, it is provided a detailed comparison between the dosage and properties of more than a hundred of mixtures proposed by several authors in the last ten years of technology. This becomes a useful tool to recognize correlations between dosages and properties and validate or no preconceived ideas about this material. Based on this state of art analysis was performed the later development of mixtures, on Chapter 4, which analized the effect of use of simpler components and processes on the UHPFRC. The main idea was use local components available in the Spanish market, identifying the combinations that provide the best rheological and mechanical properties. Steam curing use was avoided since a process simplification is intended. Diferent dosages were developed to be adapted to various levels of performance, and always trying to be as economical as possible. The concretes designed were selfcompacting and mainly combined two fiber types (hybrid), as the flexural performance was of greater relevance. The compressive strength obtained varied in the range between 100 and 170 MPa (cube L=100 mm), and the flexural strength between 15 and 45 MPa (prism 100 x 100 x 500 mm). Some of the components introduced are very rarely used in UHPFRC, as limestone coarse aggregate or FC3R, a white active residue from the petrol industry. As a result of the research, some simple and practical tips are provided for designers of UHPFRC dosage. At the end of this chapter, five dosages are characterized as examples of useful concretes for different requirement applications. In a second part, the idea of a bolted joint connection between UHPFRC elements was proposed. The connection system would be especially useful for struts and ties elements, as truss structures. The possible UHPFRC failure modes were introduced and two different types of tests were designed and performed to evaluate the joint capacity. The geometry of the UHPFRC elements was modified in order to correlate it with the failure mode and maximum load reached. Also a linear finite element analysis was performed to analyze the UHPFRC elements connection. This supported the results of the experimental tests to deduce formulations that predict the maximum load for each failure mode. Finally, a real size truss structure was assembled with bolted joints and tested to verify the good structural behavior of these connections. To conclude, some applications designed and developed at the Universitat Politècnica de València with the methods and knowledge acquired on UHPFRC are abstracted. In many of them the material was mixed and poured in a traditional precast concrete company, providing adequate rheological and mechanical results. This showed the viability of simpler UHPFRC technology enabling some of the first applications in Spain with this material. / Camacho Torregrosa, EE. (2013). Dosage optimization and bolted connections for UHPFRC ties [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/34790

Precast concrete hollow core floor units are frequently used in multistorey steel- framed buildings where they bear on to the top flanges of universal beams. The steel beam is normally designed in bending in isolation from the concrete slab and no account is taken of the composite beam action available with the precast units. Although some commercial data are avail- able, there is no general design guidance to cover the wide range of material and geometric variables found in this form of construction. This paper summarizes research carried out at the University of Nottingham on this form of construction and presents the results of three full-scale bending tests of steel beams acting com- positely with proprietary precast hollow core slabs. The 150 mm deep units were attached to the universal beams through 19 mm diameter headed shear studs, and tested in four-point bending over a span of 6 m. For typical geometry and serial sizes the composite beams were found to be twice as strong and nearly three times as sti as the equivalent isolated steel beams. The failure mode was ductile, and may be controlled by the correct use of small quantities of tie steel and in situ infill concrete placed between the precast units. To generalize the findings, isolated push- off tests and eccentric compression tests were used to study the horizontal interface shear resistance of the headed studs and the strength of the slab, respectively.

no / The recently published report on Rethinking Construction in the UK has highlighted the need to reduce on-site activities as part of its drive for greater efficiency, improved quality and greater certainty in the delivery of construction projects. For multi-storey buildings, the use of precast slabs in the floors - particularly if this can be done without the need for in-situ screeds - drastically reduces the volume of on-site concreting required. Although the use of precast hollow core slabs in steel framed buildings are common, their use in composite design with steel beams is relatively new. By designing the steel beams and precast hollow core slabs compositely, a reduction in beam size and overall floor depth can be achieved, which would lead to an overall reduction in construction cost. This paper summarises the recent developments and on-going research on composite construction with precast hollow core slabs.

This article presents the design procedures for the use of precast hollowcore slabs in steel-concrete composite construction. The paper also summarises the recent and on-going work on the transfer of this knowledge into the Australian construction industry. Whilst it is common practice to use precast concrete planks in Australian building construction, the benefits of composite behaviour with steel beams have not yet been fully realised with these systems, (National Precast Concrete Association of Australia, 2003). The use of precast hollowcore slabs in steel composite construction has seen rapid growth in popularity since it was first developed in the 1990s. The main advantages of this form of construction are that precast hollowcore slabs can span up to 15 metres without propping. The erection of 1.2 metre wide precast concrete units is simple and quick, shear studs can be pre-welded on beams before delivery to site thereby offering the savings associated with shorter construction times.

Both the identification and validation of expedient portland cement concrete (PCC) repair technologies have been the focus of the pavements research community for decades due to ever decreasing construction timelines. Precast concrete panel technology offers a potential repair alternative to conventional cast-in-place PCC because the panel is fully cured and has gained full strength prior to its use. This repaired surface may be trafficked immediately, thus eliminating the need for long curing durations required for conventional PCC. The literature reveals a number of precast PCC panel investigations in the past 50 years; however precast technology has only recently gained acceptance and increased use in the US for highway pavements. Furthermore, only limited information regarding performance of airfield applications is available. Following a review of the available technologies, an existing panel prototype was redesigned to allow for both single- and multiple-panel repairs. A series of various sized repairs were conducted in a full-scale airfield PCC test section. Results of accelerated testing indicated that precast panels were suitable for airfield repairs, withstanding between 5,000 and 10,000 passes of C-17 aircraft traffic prior to failure. Failure was due to spalling of the transverse doweled joints. The load transfer characteristics of the transverse joint were studied to determine if the joint load test could be used to predict failure. Results showed that the load transfer efficiency calculations from the joint load test data were not useful for predicting failure; however differential deflections could possibly be applied. Additionally, the practice of filling the joints with rapid-setting grout may have resulted in higher measurements of load transfer efficiency. To determine the stresses generated in the doweled joint, three-dimensional finite element analyses were conducted. Results indicated that the dowel diameter should be increased to reduce stresses and to improve repair performance. Finally, the precast repair technology was compared to other expedient repair techniques in terms of repair speed, performance, and cost. Compared to other methods, the precast panel repair alternative provided similar return-to-service timelines and traffic performance at a slightly higher cost. Costs can be minimized through modification to the panel design and by fabricating panels in a precast facility. Modifications to the system design and placement procedures are also recommended to improve the field performance of the panels. / Ph. D.

The development of precast concrete housing systems provides an opportunity to easily and inexpensively incorporate solar energy collection by casting collector tubes into the roof structure. A design is presented for a precast solar water heating system used to aid in meeting the space and domestic water heating loads of a single family residence. A three-dimensional transient collector model is developed to characterize the precast solar collector's performance throughout the day. The model describes the collector as a series of segments in the axial direction connected by a fluid flowing through an embedded tube. Each segment is represented by a two-dimensional solid model with top boundary conditions determined using a traditional flat plate solar collector model for convection and radiation from the collector cover plate. The precast collector is coupled to a series solar assisted heat pump system and used to meet the heating needs of the residence. The performance of the proposed system is compared to the performance of a typical air to air heat pump. The combined collector and heat pump model is solved using Matlab in conjunction with the finite element solver, Femlab. Using the system model, various non-dimensional design and operating parameters were analyzed to determine a set of near optimal design and operating values. The annual performance of the near optimal system was evaluated to determine the energy and cost savings for applications in Atlanta, GA and Chicago, IL. In addition, a life cycle cost study of the system was completed to determine the economic feasibility of the proposed system. The results of the annual study show that capturing solar energy using the precast collector and applying the energy through a solar assisted heat pump can reduce the electricity required for heating by more than 50% in regions with long heating seasons. The life cycle cost analysis shows that the energy savings justifies the increase in initial cost in locations with long heating seasons but that the system is not economically attractive in locations with shorter heating seasons. / Master of Science

M.S.