This dissertation presents three different aspects of the incorporation of directionality into the Monte Carlo ray-trace (MCRT) environment: (1) the development of a methodology for using directional surface optical data, (2) the measurement of the bi-directional reflectivity functions for two different surfaces, and (3) MCRT simulations performed using these directional data sets. The methodology presented is based upon a rigorous analytical formulation and is capable of performing simulations of radiation exchange involving directional emission, absorption and reflection given the bi-directional reflectivity functions (BDRF) of the participating surfaces. A wavelet compression technique is presented for the management of extremely large directional data sets. The BDRFs of two different surfaces were acquired using a Surface Optics Corporation model SOC-250 bi-directional reflectometer. These data were processed according to the methodology presented and an MCRT code was used to simulate the action of the SOC-250 in measuring radiant energy reflected from the surfaces of the two samples when illuminated by the source of the SOC-250. Another MCRT code was used to simulate the radiant energy reflected into a plane at the exit of an open-ended rectangular box when the entrance to the box is illuminated by source of the SOC-250. The RMS error between the MCRT simulations of sampling using the SOC-250 and the measured data were determined and then divided by the mean BDRF level of the measured data (RMS/mean[rho]) to provide an estimate of convergence. The RMS/mean[rho] was observed to fall from as much as 138 to 0.84 for the aluminum substrate coated with Krylon Shortcuts Hunter Green Satin aerosol paint as the number of energy bundles emitted in the MCRT simulation went from 103 to 106 at an incident zenith angle of 40 deg. The RMS/mean[rho] was observed to fall from as much as 2.2 to 0.2 for the Norton (150 Fine grit) all-purpose sandpaper coated with Krylon Shortcuts Hunter Green Satin aerosol paint as the number of energy bundles emitted in the MCRT simulation went from 103 to 106 at an incident zenith angle of 40 deg. / Ph. D.

Black coatings essentially absorb incident light at all wavelengths from all directions. They are used when minimal reflection or maximum absorption is desired and therefore are effective in applications that require control of stray light. Our motivation stems from the use of black coating Lord Aeroglaze® Z302 in aerospace and remote sensing applications and the desire to support the development of bidirectional spectral models that can be used successfully to predict the performance of optical instruments such as telescopes. The bidirectional reflectance distribution function (BRDF) is an indispensable parameter in the optical characterization of such coatings. The current effort involves investigation of the BRDF of the commercial black coating Aeroglaze® Z302. An automated goniometer reflectometer has been designed, fabricated and successfully used for performing the BRDF measurements of Z302 at visible and ultraviolet wavelengths and at both polarizations. The current contribution involves study of Z302 samples prepared at different thicknesses and by different methods, which provides insight about influence of surface roughness on BRDF of Z302. / Master of Science / When light falls on different materials it undergoes various phenomenon such as reflection, refraction, absorption and scattering. The amount of each phenomenon varies with the optical nature of a material as well as the wavelength and direction of the light. Therefore, understanding the optical properties of materials at various wavelengths of light is necessary for effectively using those materialsin specific applications which require light to be efficiently reflected or absorbed. This research studies an optical property known as Bidirectional Reflectance Distribution Function (BRDF) of a black coating called Lord Aeroglaze Z302. Black coatings are materials that ideally absorb almost all light that falls on them irrespective of the light’s direction and wavelength. They are used in applications where maximum absorption of light is required. One such application which relates to the motivation for this research is absorbing unwanted light in instruments used in space such as telescopes and radiometers. Z302 is used in the Clouds and the Earth’s Radiant Energy System (CERES) instruments developed by NASA. BRDF is an important parameter which gives information about all other optical properties of a surface and can be used to know optical performance of that surface. The current work describes the experiments and an automated device developed, called reflectometer, to measure the BRDF of Z302 at different angles and wavelengths of light. The results are reported for different thickness samples of Z302 coating, and two different wavelengths of light that belong to the visible and ultraviolet spectrum of light.

No description available.

Στην παρούσα διδακτορική διατριβή έγινε μελέτη πολυμερικών βουρτσών που διαμορφώνονται από συμπολυμερή πολυστυρενίου-πολυβουταδιενίου που φέρουν στην άκρη τους ομάδες ικανές να προσροφηθούν (PS-PB-Zw) Η μελέτη έγινε κυρίως με την τεχνικής της μέτρησης δυνάμεων (SFA) και της ανάκλασης νετρονίων. Ιδιαίτερο ενδιαφέρον παρουσιάζουν οι γραμμικές πολυμερικές αλυσίδες όπου ένα μεγάλου μοριακού βάρους πολυμερές φέρει στην άκρη του μια μόνο ακραία ομάδα. Τα γραμμικά αυτά συμπολυμερή είχαν μελετηθεί και στο παρελθόν. Το ζητούμενο όμως ήταν να μεταβάλλουμε την αρχιτεκτονική αυτή και να παρατηρήσουμε τις πιθανές μεταβολές στα ποιοτικά χαρακτηριστικά των προσροφημένων πολυμερικών στρωμάτων που διαμορφώνουν. Ως μέτρο σύγκρισης μελετήσαμε αρχικά τις ήδη μελετημένες γραμμικές αλυσίδες και στη συνέχεια προχωρήσαμε στη μελέτη των νέων δειγμάτων. Προσθέσαμε δύο και τρεις ακραίες ομάδες στο άκρο της πολυμερικής αλυσίδας μεγάλου μοριακού βάρους και αναμέναμε σύμφωνα με θεωρητικές προβλέψεις αύξηση στο προσροφημένο ποσό. Η αύξηση αυτή θα ήταν εμφανής μέσω της αύξησης του πάχους του πολυμερικού στρώματος που εύκολα μπορεί να μετρηθεί με την τεχνική της μέτρησης των δυνάμεων αλληλεπίδρασης. Επίσης μετρήσαμε άμεσα το προσροφημένο ποσό και με την τεχνική της ανάκλασης νετρονίων για πολυμερή τριών διαφορετικών μοριακών βαρών (25000, 70000 και 150000). Το σημαντικότερο αποτέλεσμά μας είναι ότι δεν παρατηρήσαμε αύξηση στο προσροφημένο ποσό σε σχέση με τις γραμμικές αλυσίδες και σε χρόνους ενός τυπικού πειράματος. Υπήρχε ωστόσο η υποψία ότι σε βάθος χρόνου μπορεί να αυξάνεται το προσροφημένο ποσό. Για το λόγο αυτό διεξαγάγαμε μια σειρά από μετρήσεις «κινητικής» με την τεχνική της ανάκλασης νετρονίων, αλλά και με συμπληρωματικές τεχνικές (διέγερση επιφανειακών πλασμονίων). Καμία μεταβολή δεν παρατηρήσαμε στο προσροφημένο ποσό, ούτε σε βάθος χρόνου αλλά ούτε και με την προσθήκη επιπλέον ακραίων ομάδων ικανών να προσροφώνται σε επιφάνειες. Στη συνέχεια επεκτείναμε τη μελέτη μας στην «αντίστροφη» αρχιτεκτονική. Διατηρήσαμε μια ακραία ομάδα και προσθέσαμε δύο και τρεις πολυμερικές αλυσίδες μεγάλου μοριακού βάρους (Μr=70000). Η αρχιτεκτονική που διαμορφώσαμε με τον τρόπο αυτό ήταν ουσιαστικά αρχιτεκτονική αστεροειδών πολυμερών με μικρό αριθμό πλοκαμιών. Στη περίπτωση αυτή παρατηρήσαμε μια σταδιακή μείωση του προσροφημένου ποσού με την προσθήκη επιπλέον βραχιόνων στο αστέρι. Η μείωση αύτη έχει παρατηρηθεί τόσο από μετρήσεις δυνάμεων, όσο και από μετρήσεις με ανάκλαση νετρονίων. Στα προφίλ δυνάμεων παρατηρούμε διαφοροποιήσεις σε σχέση με την γενική εικόνα που εμφανίζουν οι πολυμερικές βούρτσες. Αυτές οι διαφοροποιήσεις μπορούν να ερμηνευτούν με τη βοήθεια θεωρητικών προβλέψεων για τη συμπεριφορά των αστεροειδών πολυμερών. Η μείωση του προσροφημένου ποσού με αύξηση του αριθμού των πλοκαμιών μπορεί να αποδοθεί είτε σε λόγους κινητικής, είτε σε λόγους αλληλεπίδρασης μεταξύ των πολυμερικών αλυσίδων και μεταξύ των πλοκαμιών ενός μακρομορίου. Επίσης στη παρούσα διδακτορική διατριβή μελετήσαμε τη συμπεριφορά προσροφημένων ασθενών πολυ-ηλεκτρολυτών. Οι πολυ-ηλεκτρολύτες συγκεντρώνουν σταδιακά την προσοχή όλο και περισσότερων ερευνητών καθώς εμφανίζουν αρκετές σημαντικές εφαρμογές και είναι συμβατοί με βιολογικά συστήματα. Μέχρι πριν λίγο καιρό οι ασθενείς πολυ-ηλεκτρολύτες, όπως είναι το πολυακρυλικό οξύ που μελετούμε στη παρούσα εργασία, δεν είχαν μελετηθεί εκτενώς. Η μελέτη τους παρουσιάζει δυσκολίες, λόγω της πολυπλοκότητας στη συμπεριφορά τους. Αυτή εξαρτάται τόσο από τη συγκέντρωση άλατος του διαλύματος, όσο και από το pH. Μεταβάλλαμε τόσο τη συγκέντρωση άλατος του διαλύματος, όσο και το pH του διαλύματος εξετάζοντας πως αυτά επηρεάζουν το πάχος του προσροφημένου στρώματος και τα ποιοτικά χαρακτηριστικά των πολυ-ηλεκτρολυτικών προσροφημένων στρωμάτων. Παρατηρήσαμε λοιπόν μείωση του πάχους της πολυ-ηλεκτρολυτικής βούρτσας με αύξηση της συγκέντρωσης άλατος. Το αποτέλεσμα αυτό είναι πλήρως συμβατό με θεωρητικές προβλέψεις. Στη συνέχεια εξετάσαμε τη συμπεριφορά των ασθενών πολυ-ηλεκτρολυτών μεταβάλλοντας το pH του διαλύματος. Παρατηρήσαμε ότι με αύξηση του pH οι πολυμερικές αλυσίδες εκτείνονταν αυξάνοντας το πάχος της πολυμερικής βούρτσας. Αυτή η συμπεριφορά είναι άμεσο αποτέλεσμα της αύξησης του βαθμού διάστασης των πολυμερικών αλυσίδων. Αυξάνοντας το pH περισσότερα φορτία αποσπώνται από την πολυμερική αλυσίδα φορτίζοντάς την έτσι ισχυρότερα. Οι απωστικές ηλεκτροστατικές αλληλεπιδράσεις μεταξύ των φορτίων εξαναγκάζουν την αλυσίδα σε έκταση επιμηκύνοντας την πολυμερική βούρτσα. Τα αποτελέσματα αυτά είναι επίσης σε πλήρη συμφωνία με θεωρητικές προβλέψεις. / Flexible polymer chains end-tethered to a surface in good solvent tend to extend away from the surface due to excluded volume interactions. At sufficiently high grafting densities the chains become elongated normal to the surface, this extension being opposed by an elastic restoring force of entropic origin to form a layer of stretched chains referred to as a “polymer brush”. These systems have been studied extensively in recent years by numerous experimental techniques and theoretical methods. In the present investigation we have studied asymmetric star-shaped polymers whereby the different arms are either non-adsorbing PS chains or short PB chains terminating in a zwitterionic end-group known to adsorb strongly on surfaces such as mica or quartz. In this manner, it is possible on the one hand to form brushes with a single PS chain, but multiple zwitterionic stickers, and on the other to study the reverse case of multiple non-adsorbing arms attached to a surface via a single zwitterions. We have used the surface force balance technique to determine the interaction between such brush-layers formed on mica and neutron scattering to determine the absorbed amount and interanchor distance. Interactions between polymer brushes formed by highly asymmetric star-like polymers with a long PS arm and one, two or three short PB arms each terminating in a zwitterionic end-group were studied in order to explore the effect of the sticking energy on the brush structure. Polystyrene stars with two and three tails bearing a single end group were also studied to investigate how the height of the adsorbed layer and the grafting density are affected. Our measurements show no significant differences between PS with 1, 2 and 3 end groups. This may be due to kinetic reasons since additional polymer chains are hindered from attaching to a brush-bearing surface. The behavior of two PS chains with one end-group ((PS)2-PB-X) seems not to differ appreciably from that of PS-PB-X copolymer. On the other hand three PS chains with one end-group ((PS)3-PB-X) appeared to form layers with smaller brush height and greater interanchoring distance, relative to PS-PB-X layers. We can attribute this to the extra stretching that the three-chain architecture imposes on the adsorbed brush. In the present investigation we have also studied weak polyelectrolytes. Polyelectrolytes (charged polymer chains) remain among the least understood materials despite their importance in biology (proteins, DNA) and materials science. Their behavior and characteristics are not yet fully understood because of complicated correlations due to their charged nature that gives rise to long-range interactions. The counterplay of their properties as polymers and electrolytes with counterions around polyelectrolyte chains imposes additional difficulties on explaining their behavior. The association of counterions around polyelectrolytes and the pH of the solution are two parameters than can affect the properties of such systems. Especially weak polyelectrolytes (like poly-acrylic acid) are even sensitive to pH changes because of the alterable degree of dissociation. We measured forces between two charged polymer layers of Poly (isoprene-acrylic acid) diblock copolymers adsorbed on mica surfaces. Poly (isoprene-acrylic acid) diblock copolymers can be adsorbed from one end (poly-isoprene) which is sorter than the poly-(acrylic acid) part. The properties of the polymer layer at various salt concentrations and different pH of the solutions were measured by Surface Forces Apparatus. Information about the height of the polymer layer, and the adsorbed amount were extrapolated. The extracted results were compared with theoretical predictions showing well fit.

No description available.

No description available.

Magnetic recording media refers to the disc shaped thin film magnetic medium present inside the hard disk drive of a computer. Magnetic recording is an important function of the hard disk drive by which information such as text, pictures, audio and videos are stored. Information is broken down to a simple binary format and is stored as magnetised bits along the tracks of the disk forming the hard drive. Over the years advancements in research on the type of magnetic materials used has allowed increased data storage capacities by reducing magnetic bit sizes. It is with this advancement in magnetic data storage, that we have today's hard disk drive technology, which uses a perpendicular magnetic medium to store data. A perpendicular magnetic medium is a multi-layered magnetic thin film structure with the topmost layer comprising nanoscale magnetic grains of high perpendicular anisotropy. The topmost recording layer (RL) is mapped into individual bits of 80-100 nm² area that consist of 5-10 nm diameter CoCrPt grains, embedded in an oxide matrix. A bit area is defined to ensure a significant number of stable grains allowing data to be stored in each bit as a ‘0' or a ‘1' depending on its switched magnetic state. The magnetic grains if sputtered below a threshold grain size tend to suffer from thermal fluctuation and instability due to super-paramagnetic effects, hence bringing limitations to grain size. As a result of this, research in recent years has been directed at introducing a softer magnetic exchange coupled composite (ECC) layer above the recording layer. This layer facilitates the delicate balance of switching smaller grains with strong magneto-crystalline anisotropy at lower magnetic fields, by exchange coupling with the CoCrPt grains in the recording layer. However this technique of increasing the efficiency in the perpendicular magnetic medium by introducing ‘facilitating' layers is an area that is still being widely researched and understood. Although numerous surface and bulk analysis techniques exist to study magnetic and surface properties of these materials, there is limited information on the structural and magnetic properties of these materials at the nanoscale level. The reported work investigates the structural and magnetic properties of the magnetic grains and multi-layers in the perpendicular magnetic medium using polarised neutron scattering and reflectivity techniques. The work investigates the structural and magnetic properties of the CoCrPt grains, apart from understanding the CoCrPt magnetic grain switching. The work also investigates the magnetisation in the layers of the thin film perpendicular media structure using polarised neutron reflectivity (PNR). Using polarised small angle neutron scattering (PolSANS), it has been shown that ferromagnetic ordered core region of the CoCrPt grain in the recording layer is smaller than the physical CoCrPt granular structure. The magnetic switching behaviour of the CoCrPt grain at different magnetic fields is also analysed and the experimental PolSANS data is fitted with non-interacting size-dependent analytical grain switching models. This result provides significant evidence that the magnetic anisotropy increases with grain size, with larger magnetic grains having larger magnetic anisotropy. Polarised neutron scattering experiments are carried out with the magnetically softer exchange coupled composite (ECC) layer included in the thin film magnetic structure. The first experiments investigate if the ECC layer contributes to the nuclear and magnetic interference scattering term in the experimenting scattering data. The experiments clearly show that there is no contribution from the ECC layer in the nuclear and magnetic scattering interference term. The role of the ECC layer in the magnetic switching process is then investigated at different magnetic fields. The ECC layer was found to influence the size-dependent magnetic grain switching of the CoCrPt grains in the recording layer and a detailed investigation is presented in the reported work. Polarised neutron reflectivity (PNR) experiments have also been carried out with the ECC layer on the perpendicular magnetic media samples. These experiments investigate the composition and thickness of the thin film structure, while also providing information on the magnetic state of the thin films under the influence of an in-plane magnetic field. The in-plane magnetisation in the recording and ECC layer is determined at different in-plane magnetic fields. The magnetisation values determined for the ECC layer and the recording layer (RL) at different in-plane magnetic fields help better understand the differences in their magnetic properties.

Seismic inversion using a global optimization algorithm is a non-linear, model-driven process. It yields an optimal solution of the cost function – reflectivity/acoustic impedance, when prior information is sparse. The inversion result offers detailed interpretations of thin layers, internal stratigraphy, and lateral continuity and connectivity of sand bodies. This study compared two stable and robust global optimization techniques, Simulated Annealing (SA) and Basis Pursuit Inversion (BPI) as applied to post-stack seismic data from the Gulf of Mexico. Both methods use different routines and constraints to search for the minimum error energy function. Estimation of inversion parameters in SA is rigorous and more reliable because it depends on prior knowledge of subsurface geology. The BPI algorithm is a more robust deterministic process. It was developed as an alternative method to incorporating a priori information. Results for the Gulf of Mexico show that BPI gives a better stratigraphic and structural actualization due to its capacity to delineate layers thinner than the tuning thickness. The SA algorithm generates both absolute and relative impedances, which provide both qualitative and quantitative characterization of thin-bed reservoirs.

O principal objetivo deste estudo foi avaliar a refletância e sua influência no comportamento térmico de tintas refletivas e tintas convencionais aplicadas em telhas de fibrocimento para cobertura de habitações brasileiras. Foram realizados ensaios em laboratório de determinação de cor e de brilho por medida instrumental e determinação da refletância por análise espectrofotométrica em películas. Para o estudo do comportamento térmico foram realizados ensaios de simulação em laboratório com corpos-de-prova expostos à radiação infravermelha emitida por lâmpadas e de exposição à radiação solar em campo através de protótipos com monitorização da temperatura durante as exposições. Os resultados dos ensaios de determinação de cor e de brilho mostraram que as pinturas refletivas e convencionais realmente apresentaram cores correspondentes. Os resultados de refletância mostraram que as pinturas refletivas apresentaram valores de refletância superiores em relação às tintas convencionais, o que foi comprovado pela temperatura medida nos ensaios de exposição à radiação infravermelha e radiação solar. A conclusão do estudo é que as tintas refletivas têm potencial para redução da temperatura superficial da telha de fibrocimento e que é necessária uma continuidade do estudo de durabilidade e do desempenho térmico de tintas refletivas coloridas. / The main purpose of this study was to investigate the effect of reflective colored paints and conventional colored paints applied on fiber cement corrugated roofing sheets, proving whether both type of paints can present different reflection characteristics in the infrared solar radiation and high thermal performance. Color and gloss were measured by instrumental methods and reflectivity (reflection coefficient) was measured using spectrophotometers equipped with integrating spheres in free paint films. In order to investigate the thermal performance of reflective and conventional paints, simulation tests were performed in laboratory by IR lamps using fiber cement specimens and in field by exposure solar radiation using prototypes with temperature monitoring. The results showed that the reflective paints present higher reflectivity and better thermal performance than the conventional paint, independently of the color. The results showed that the reflective paints present potential to reduce superficial temperature of fiber cement corrugated roofing sheets. It is necessary to continue the reflective colored paints study on durability and thermal performance by exposure tests.

With 400 Gbps Ethernet being developed at the time of writing this thesis, all-optical networks are a solution to the increased bandwidth requirements of data communication allowing architectures to become increasingly integrated. High density integration of optical components leads to potential ‘Optical/Photonic’ electromagnetic compatibility (EMC) and signal integrity (SI) issues due to the close proximity of optical components and waveguides. Optical EMC issues are due to backscatter, crosstalk, stray light, and substrate modes. This thesis has focused on the crosstalk in Optical Add/Drop Multiplexers (OADMs) as an EMC problem. The main research question is: “How can signal integrity be improved and crosstalk effects mitigated in small-sized OADMs in order to enhance the optical EMC in all-optical networks and contribute to the increase in integration scalability?” To answer this question, increasing the crosstalk suppression bandwidth rather than maximizing the crosstalk suppression ratio is proposed in ring resonator based OADMs. Ring resonators have a small ‘real estate’ requirement and are, therefore, potentially useful for large scale integrated optical systems. A number of approaches such as over-coupled rings, vertically-coupled rings and rings with random and periodic roughness are adopted to effectively reduce the crosstalk between 10 Gbps modulated channels in OADMs. An electromagnetic simulation-driven optimization technique is proposed and used to optimize filter performance of vertically coupled single ring OADMs. A novel approach to analyse and exploit semi-periodic sidewall roughness in silicon waveguides is proposed. Grating-assisted ring resonator design is presented and optimized to increase the crosstalk suppression bandwidth.