No description available.

No description available.

No description available.

No description available.

No description available.

No description available.

Bibliography: p. 41.

Thesis (MScEng) -- Stellenbosch University, 2004. / ENGLISH ABSTRACT: The development of a small, cost effective short range FM-CW radar as well as the design and optimization of a double helix antenna is discussed. The FM-CW radar operates at Sband (2450 - 2550 MHz) and is limited at a maximum transmitted power of 5 dBm. The system is required to detect reflections from objects up to a 30 m range. This was made possible largely by the effective high gain antenna design and improved system isolation between the transmitted and received signals. The complete design process from fundamental requirements, through various simulations and system analysis to the final electronic circuit is discussed. The design was also built and measured in the laboratory and initial field measurements were taken. The following aspects were considered: Relation between the beat frequency and various FM-CW radar system parameters based on the theory, preliminary measurements and simulations. Radar component assessment and design. Design of a low cost Lange coupler that isolates the system's transmit and receive signals, which operates as a 90° hybrid and is used to feed a dual-fed circularly polarized patch antenna. A circularly polarized patch antenna and double helix antenna were designed, built and measured in an anechoic chamber. The antennas were implemented in the final radar system and compared on the basis of their contribution to the system's performance. Integrating the final radar system on a circular 60 mm diameter PCB with a double helix antenna mounted on top. The final radar system is able to measure range up to 40 m and meets all the design requirements. The signal processing of the measured beat frequency, however, can be taken further. / AFRIKAANSE OPSOMMING: Die ontwikkeling van 'n klein, koste effektiewe kort-afstand FM-CW radar, sowel as die onwerp en optimalisering van 'n dubbele heliks-antenna word bespreek. Die FM-CW radar werk by S-band (2450 - 2550 MHz) en is beperk tot 'n maksimum uitsaaidrywing van 5 dBm. Van die stelsel word vereis om weerkaatsings van voorwerpe tot op 'n afstand van 30 m waar te neem. Dit is grootliks moontlik gemaak deur die hoë aanwins antenna-ontwerp en verbeterde isolasie tussen die stelsel se uitsaai- en ontvangseine. Die volledige ontwerpsproses van die fundamentele vereistes af tot die finale elektroniese stroombaan word bespreek. Verskeie simulasies andstelselanalises is gebruik om die finale FM-CW radar te realiseer. Die ontwerp is vervolgens in die laboratorium gebou en gemeet en aanvangsveldmetings is geneem. Die volgende aspekte is in nagevors: Verband tussen die puls-frekwensie en verskeie FM-CW radar stelselparameters gebaseer op die teorie, inleidende metings en simulasies. Ontleding van verskeie radarkomponente en -stelselontwerp. Ontwerp van 'n lae koste Lange-koppelaar met die doelom die stelsel se uitsaai- en ontvangseine te isoleer. Die Lange-koppelaar dien as 'n 90° hibriede wat gebruik word om 'n dubbele-voer sirkulêr gepolariseerde mikrostrookantenna aan te dryf. Verder is 'n sirkulêr gepolariseerde mikrostrook-antenna en 'n dubbele heliksantenna ontwerp en opgemeet in 'n anarqoïese kamer. Beide antennas is geïmplimenteer in die finale radarstelsel en is vergelyk op grond van hulle rol in die stelsel se funksionering. Die finale stelsel is geïntegreer en gebou op 'n ronde 60 mm deursnit PCB met 'n dubbele helix-antenna bo-op gemonteer. Die finale radarstelsel kan afstand tot op 40 meter bepaal en voldoen aan al die gestelde vereistes. Seinverwerking van die gemete puls-frekwensie kan nog verder ontwikkel word.

Thesis (MTech (Electrical Engineering))--Cape Peninsula University of Technology, 2009 / This thesis presents the design, analysis and implementation of an eight-element phased array antenna for wideband X-band applications. The microstrip phased array antenna is designed using eight quasi-Yagi antennas in a linear configuration and is printed on RT/Duroid 6010LM substrate made by Rogers Corporation. The feeding network entails a uniform beamforming network as well as a non-uniform -25 dB Dolph-Tschebyscheff beamforming network, each with and without 45° delay lines, generating a squinted beam 14° from boresight. Antenna parameters such as gain, radiation patterns and impedance bandwidth (BW) are investigated in the single element as well as the array environment. Mutual coupling between the elements in the array is also predicted. The quasi-Yagi radiator employed as radiating element in the array measured an exceptional impedance bandwidth (BW) of 50% for a S11 < -10 dB from 6 GHz to 14 GHz, with 3 dB to 5 dB of absolute gain in the frequency range from 8 GHz to 11.5 GHz. The uniform broadside array measured an impedance BW of 20% over the frequency band and a gain between 9 dB to 11 dB, whereas the non-uniform broadside array measured a gain of 9 dB to 11 dB and an impedance BW of 14.5%. Radiation patterns are stable across the X-band. Beam scanning is illustrated in the E-plane for the uniform array as well as for the non-uniform array.

Thesis (MEng (Electrical and Electronic Engineering))--University of Stellenbosch, 2002. / An efficient radiating strucllire was needed for borehole pulsed radar applications in the 10-100 MHz frequency band. Both resistively loaded and insulated wire antennas were investigated and an active antenna is proposed as a fmal solution. The study proceeded from the characterization of the origin of radiation on a conductive dipole wire antenna when excited with a transient. Different radiation mechanisms were identified when the antenna was excited with a current or voltage source. The wire antenna in insulated surroundings was modelled using transmission line theory to simulate the antenna in the borehole environment. The transmission line model proved to be useful for investigating conducting and resistively loaded antennas for the dimensions associated with borehole surveys. From the modelling results, it became apparent that the asymmetric resistively loaded antenna might provide the best practical solution. This antenna displays reasonably stable input impedance and low far-field variations for different theta angles across the desired frequency band. Different percentage Wu-King resistive profiles were studied to show that a 50% reduction in the normal Wu-King resistor values will add only a little ringing but have better amplitude response than the 100% Wu-King loading. The asymmetric resistively loaded antenna has better sensitivity to receiving transients when combined with a high impedance source load than when symmetrically loading the antenna. An active antenna incorporating the asymmetric resistively loaded antenna and a low noise current feedback front end amplifier was built and measured in an air environment. The results show that the active antenna has a flat transfer function and reacts as a wide band electric field probe with better resolution than in the conventional 50 Q loaded case