This thesis has sought to provide another look at RF interference at the fundamental level. While previous interference control and regulation methods have existed in the literature, they were more focused on preventing the interference from happening. On the contrary, we have taken a different approach of correcting the interference once it has happened. This allows the transmitters to be more nonlinear, passive filter design to be eased, and receivers to be aware of interference problems. Under this unifying theme of building intelligent radios where receivers are more cognizant of the transmission environment, we have presented a number of architectures.

The objective of this research is to design and implement low-noise wideband RFIC components with CMOS technology for the direct-conversion architecture. This research proposes noise reduction techniques to improve the thermal noise and flicker noise contribution of a low noise amplifier (LNA) and a mixer. Of these techniques, the LNA is found to reduce noise, boost gain, and consume a relatively low amount of power without sacrificing the wideband and linearity advantages of a conventional common gate (CG) topology. The research concludes by investigating the proposed mixer topology, which senses and compensates local oscillator (LO) phase mismatches, the dominant cause of flicker noise.

Thesis (Ph. D.)--Carleton University, 2004. / Includes bibliographical references (p. 217-223). Also available in electronic format on the Internet.

Thesis (M. App. Sc.)--Carleton University, 2004. / Includes bibliographical references (p. 112-118). Also available in electronic format on the Internet.

Thesis (M.App.Sc.) - Carleton University, 2005. / Includes bibliographical references (p. 79-86). Also available in electronic format on the Internet.

Thesis (M.App.Sc.) - Carleton University, 2006. / Includes bibliographical references (p. 124-128). Also available in electronic format on the Internet.

Thesis (Ph. D.)--Electrical and Computer Engineering, Georgia Institute of Technology, 2006. / John Papapolymerou, Committee Chair ; Joy Laskar, Committee Member ; John Cressler, Committee Member ; Alan Doolittle, Committee Member ; Clifford Henderson, Committee Member.

In this dissertation, a novel approach to modeling the scattered field of a periodic corrugated cylinder, from an oblique incident planewave, is presented. The approach utilizes radial waveguide approximations for fields within the corrugations, which are point matched to approximated scattered fields outside of the corrugation to solve for the expansion coefficients. The point matching is done with TMz and TEz modes simultaneously, allowing for hybrid modes to exist. The derivation of the fields and boundary conditions used are discussed in detail. Axial and radial propagating modes for the scattered fields are derived and discussed. Close treatment is given to field equations summation truncation and conversion to matrix form, for numerical computing. A detailed account of the modeling approach using Mathematica® and NCAlgebra for the noncommutative algebra, involved in solving for the expansion coefficients, are also given. The modeling techniques offered provide a full description and prediction of the scattered field of a periodic corrugated cylinder. The model is configured to approximate a smooth cylinder, which is then compared against that of a textbook standard smooth cylinder. The methodology and analysis applied in this research provide a solution for computational electromagnetics, RF communications, Radar systems and the like, for the design, development, and analysis of such systems. Through the rapid modeling techniques developed in this research, early knowledge discovery can be made allowing for better more effective decision making to be made early in the design and investigation process of an RF project. / Includes bibliography. / Dissertation (Ph.D.)--Florida Atlantic University, 2017. / FAU Electronic Theses and Dissertations Collection

In this dissertation, a novel approach to modeling the scattered field of a periodic corrugated cylinder, from an oblique incident planewave, is presented. The approach utilizes radial waveguide approximations for fields within the corrugations, which are point matched to approximated scattered fields outside of the corrugation to solve for the expansion coefficients. The point matching is done with TMz and TEz modes simultaneously, allowing for hybrid modes to exist. The derivation of the fields and boundary conditions used are discussed in detail. Axial and radial propagating modes for the scattered fields are derived and discussed. Close treatment is given to field equations summation truncation and conversion to matrix form, for numerical computing. A detailed account of the modeling approach using Mathematica® and NCAlgebra for the noncommutative algebra, involved in solving for the expansion coefficients, are also given. The modeling techniques offered provide a full description and prediction of the scattered field of a periodic corrugated cylinder. The model is configured to approximate a smooth cylinder, which is then compared against that of a textbook standard smooth cylinder. The methodology and analysis applied in this research provide a solution for computational electromagnetics, RF communications, Radar systems and the like, for the design, development, and analysis of such systems. Through the rapid modeling techniques developed in this research, early knowledge discovery can be made allowing for better more effective decision making to be made early in the design and investigation process of an RF project. / Includes bibliography. / Dissertation (Ph.D.)--Florida Atlantic University, 2017. / FAU Electronic Theses and Dissertations Collection

The demand for higher frequency applications is largely driven by bandwidth. The evolution of circuits in the microwave and millimeter frequency ranges always demands higher performance and lower cost as the technology and specification requirements evolve. Thus the development of new processes addressing higher frequencies and bandwidth requirements is essential to the growth of any semiconductor company participating in these markets. There exist processes which can perform in the higher frequency design space from a technical perspective. However, a cost effective solution must complement the technical merits for deployment. Thus a new 0.15 um optical lithography pHEMT process was developed at TriQuint Semiconductor to address this market segment. A 40 GHz power amplifier has been designed to quantify and showcase the capabilities of this new process by leveraging the existing processing knowledge and the implementation of high frequency scalable models. The three stage power amplifier was designed using the TOM4 scalable depletion mode FET model. The TriQuint TQP15 Design Kit also implements microstrip transmission line models that can be used for evaluating the interconnect lines and matching networks. The process also features substrate vias and the thin film resistor and MIM capacitor models which utilize the capabilities of the BCB process flow. During the design stage we extensively used Agilent ADS program for circuit and EM simulation in order to optimize the final design. Special attention was paid to proper sizing of devices, developing matching circuits, optimizing transmission lines and power combining. The final design exhibits good performance in the 40 GHz range using the new TQP15 process. The measured results show a gain of greater than 13 dB under 3 volt drain voltage and a linear output power of greater than 28 dBm at 40 GHz. The 40 GHz power amplifier demonstrates that the new process has successfully leveraged an existing manufacturing infrastructure and has achieved repeatability, high volume manufacturing, and low cost in the millimeter frequency range.