De nos jours, la politique écologique encourage les constructeurs automobiles à réduire le poids global du véhicule. Des tôles d'acier fines d'épaisseur différente optimisant chaque partie de l'assemblage sont utilisées et les sidérurgistes développent des aciers de plus en plus résistants à savoir l'Acier Haute Résistance Avancé (AHSS) avec un bon compromis entre résistance mécanique et ductilité (emboutissage). Lors des essais mécaniques de soudage hétérogène AHSS, des modes de fractures inhabituels sont observés, notamment le long de l'interface entre la zone affectée par la chaleur (ZAT) et la zone de fusion ou zone fondue (ZF). Ces fractures se produisent généralement avec une résistance inférieure à celle attendue pour ces soudures. Les objectifs de l'étude sont de comprendre les mécanismes de rupture au cours des essais mécaniques et de créer un modèle mécanique de FE conçu pour prédire la résistance mécanique des assemblages soudés. Tout d'abord, une étude de soudage hétérogène constituée de deux nuances d'acier bien connues d'ArcelorMittal vise à comprendre le mécanisme de défaillance et les paramètres affectant les modes de défaillance. Différentes configurations sont étudiées avec l'épaisseur. Le modèle FE est construit avec une réponse mécanique identifiée de chaque zone (matériaux de base, zones affectées par la chaleur et zone de fusion), en utilisant des modèles d'ArcelorMittal et des données expérimentales. Des critères de défaillance basés sur des dommages ductiles tenant compte de l'influence de la triaxialité sont utilisés et certains éléments cohésifs sont utilisés pour simuler une défaillance interfaciale. Deux configurations d'essais mécaniques dans le cas du soudage par résistance par points (essais de traction transversale et de traction) sont considérées. Les prédictions du modèle étaient très précises avec les modes de défaillance et les forces expérimentaux. Ensuite, cette méthode de modélisation FE a été appliquée avec succès à un boîtier de soudage par points très hétérogène comprenant un nouveau concept AHSS basse densité de troisième génération à forte teneur en aluminium et en manganèse. Les modes d'échec et les forces obtenues étaient comparables. De plus, la méthode de modélisation FE a été appliquée sur des configurations plus complexes, en particulier sur un assemblage soudé par points triple épaisseur. La robustesse du modèle pour prédire les modes de défaillance partielle et les forces d'une soudure par points triple épaisseur a été démontrée. En outre, la méthodologie de modélisation FE a été étendue à un autre type de soudage: le soudage à l'arc. Dans ce cas, deux feuilles sont soudées en configuration de chevauchement ab avec un fil d'apport. Le modèle FE permet de prédire la zone de rupture et la résistance de l'assemblage soudé. / Nowadays, ecological policy encourages carmakers to reduce the global vehicle weight. Fine steel sheets assemblies with different thickness optimizing each part of the assembly are used and steelmakers develop steels which are more and more resistant namely Advanced High Strength Steel (AHSS) with a good compromise between mechanical strength and ductility (stamping). During the mechanical tests of heterogeneous AHSS welding, unusual fracture modes are observed, in particular along the interface between the Heat Affected Zone (HAZ) and the Fusion Zone or molten zone (FZ). These fractures generally occur with lower strength than expected for these welding. The objectives of the study are to understand fracture mechanisms during mechanical testing and create a mechanical FE model is developed to be able to predict mechanical strength of the welded assemblies. Firstly, a study of heterogeneous welding constituted of two well-known steel grades of ArcelorMittal aims at understanding failure mechanism and parameters affecting the failure modes. Different configurations are studied with thickness. FE model is built with mechanical response identified of each zone (base materials, heat affected zones and fusion zone), using ArcelorMittal models and experimental data. Failure criteria based on ductile damage taking into account the influence of the triaxiality are used and some cohesive elements are used to simulate interfacial failure. Two configurations of mechanical testing in the case of Resistance Spot Welding (cross tension and tensile shear tests) are considered. Model predictions were very accurate with experimental failure modes and strengths. Then, this FE modelling method was successfully applied to a highly heterogeneous spot welding case including a new third generation low density AHSS concept with high aluminum and manganese content. Failure modes and strengths obtained were comparable. Moreover, FE modelling method was applied on more complex configurations, in particular on a triple thick spot welded assembly. The robustness of the model to predict partial failure modes and strengths of a triple thick spot weld has been demonstrated. In addition, FE modelling methodology was extended to another welding type: arc welding. In this case, two sheets are welded in ab overlap configuration with a filler wire. FE model allows predicting the failure zone and strength of welded assembly.

Conventional resistance spot welds are not visible from the outside. Therefore, it is not straightforward to evaluate the joint quality non-destructively. The pulse-echo method of manual ultrasonic is widely used for non-destructive testing. Another option is the passive magnetic flux density testing, which is being developed at Technische Universität Dresden, Germany. The spot weld is magnetized in the normal direction and the residual magnetic flux density is measured on top of the surface of the joint. This method is suitable for spot welds on typical car body steels. Previous investigations show that the magnetic properties of the materials influence the test result. In order to develop this new non-destructive testing method further, it is necessary to know the magnetic properties of the different microstructure regions of a spot weld. This article focuses on methods to measure and evaluate the magnetic properties of these regions, especially of the base material and the weld. Different measuring methods and approaches are presented and compared with each other. Based on the results, recommendations for future measurements for magnetic characterizations are given.

Friction bit joining (FBJ) is a new solid-state spot joining technology developed in cooperation between Brigham Young University of Provo Utah, and MegaStir Technologies of West Bountiful Utah. Although capable of joining several different material combinations, this research focuses on the application of FBJ to joining 5754 aluminum to DP 980 steel, two alloys commonly used in automotive applications. The thicknesses of the materials used were 0.070 inches (1.78 mm) and 0.065 inches (1.65 mm), respectively. The FBJ process employs a consumable 4140 steel bit and is carried out on a purpose built research machine. In the first stage of the weld cycle the bit is used to drill through the aluminum top sheet to be joined. After this, spindle speed is increased so that the bit tip effectively forms a friction weld to the steel bottom sheet. Momentary stoppage of the spindle facilitates weld cooling before the spindle is restarted, shearing the bit tip from the bit shank, and retracted. Incorporated into the bit tip geometry is a flange that securely holds the aluminum in place after joint formation is complete. This research consists of several developmental steps since the technology only recently began to be formally studied. Initial joint strengths observed in lapshear tensile testing averaged only 978.5 pounds (4.35 kN), with a relatively high standard deviation for the data set. Final lapshear tensile test results were improved to an average of 1421.8 pounds (6.32 kN), with a significantly lower, and acceptable, standard deviation for the data set. Similar improvements were realized during the development work in cross tension tensile test results, as average strengths increased from 255.8 pounds (1.14 kN) to 566.3 pounds (2.52 kN). Improvements were also observed in the standard deviation values of cross tension data sets from initial evaluation to the final data set presented in this work.