No description available.

No description available.

No description available.

In RF communications with a rotorcraft such as a helicopter, the rotor blades can impart a modulation onto the received signal called Rotor Blade Modulation (RBM). This modulation is caused by the reflection of a signal off the rotating blades. The reflected signal is Doppler shifted based on where the signal is reflected along the length of the blade as well as the angle between the axis of rotation and the emitter. RBM is known to degrade the performance of RF communications on rotorcraft and can be used in radar applications to detect and classify aircraft, but there is little on its usefulness in other areas. This thesis looks at the ability to utilize the RBM phenomenon on the rotorcraft itself to geo-locate and track a signal emitter on the ground. To do this a 3D RF ray tracing program was developed in C++ to produce simulations of RBM signals. The developed program is based on optical ray tracing algorithms with modified physical propagation effects for RF signals, and swapping lights and cameras for RF transmitters and receivers respectively. The ray tracer was then run over a realistic set of physical parameters to determine their effects on the received signal; this includes transmitter azimuth and elevation angle, receiver position, blade pitch, etc. along with their combinations. The simulations of the azimuth and elevation angle produce predictable modulations on the received signal. Based on the trends in the signal's modulation, a DSP algorithm was distilled down that accurately determines the azimuth and elevation angle of the transmitter from simulated signal data.

This master thesis was part of a project at the Acreo Swedish ICT AB to investigate the 28 nm FDSOI CMOS process technology for the LTE front-end application. The project has resulted in a chip that contains different test circuits such as power amplifier (PA), mixer, low noise amplifier (LNA), RF power switch, and a receiver front-end. This thesis presents the evaluation of the RF power switch. At first, a stand-alone six-stacked single pole single throw (SPST) RF power switch was designed according to Rascher, and then it was modified to single pole double throw (SPDT) RF power switch according to the requirements of the project. This report presents an overview of the FDSOI CMOS process, basic theory of the RF switch, and the evaluation techniques. The post-simulation results showed that with the proper substrate biasing and matching (50 Ω), the RF switch will provide 2.5 dB insertion loss (IL) up to 27 dBm input power and over 30 dB isolation with 30 dBm input power at 2 GHz. / Detta examensarbete har varit en del av ett projekt på Acreo Swedish ICT AB för att undersöka 28 nm FDSOI CMOS teknik för LTE front-end tillämpningar. Projektet har resulterat i ett chip som innehåller olika testkretsar: effektförstärkare, mixer, RF-effektomkoppare, LNA, och en mottagarfront-end. Denna avhandling presenterar en utvärdering av RF-omkopplaren. En SPST RF-omkopplare med sex staplade transistor konstruerades enligt Rascher. Sedan modifierades konstruktionen till en SPDT-omkoppare i enlighet med kraven för projektet. Denna rapport presenterar en översikt över FDSOI CMOS-tekniken, grundläggande teori för en RF switch samt utvärderingsmetoder. Simuleringsresultaten visade att med rätt substratbiasering och matchning (50 Ω), så ger RF-omkopplaren 2,5 dB förlust (IL) på upp till 27 dBm ineffekt och över 30 dB isolering med 30 dBm ineffekt vid 2 GHz.

With ample radio transmitters scattered throughout urban landscape, RF energy scavenging emerges as a promising approach to extract energy from propagating radio waves in the ambient environment to continuously charge low power electronics. With the ability of generating power from RF energy, the need for batteries could be eliminated. The effective distance of a RF energy scavenging system is highly dependent on its conversion efficiency. This results in significant limitations on the mobility and space requirement of conventional RF energy scavenging systems as they operate only in presence of physically large antennas and conversion circuits to achieve acceptable efficiency. This thesis presents a number of novel design strategies in the antenna and rectifier designs for miniaturized RF energy scavenging system. In the first stage, different energy scavenging systems including solar energy scavenging system, thermoelectric energy scavenging system, wind energy scavenging system, kinetic energy scavenging system, radio frequency energy scavenging system and hybrid energy scavenging system are investigated with regard to their principle and performance. Compared with the other systems, RF energy scavenging system has its advantages on system size and power density with relatively stable energy source. For a typical RF energy scavenging system, antenna and rectifier (AC-DC convertor) are the two essential components to extract RF energy and convert to usable electricity. As the antenna occupies most of the area in the RF energy scavenging system, reduction in antenna size is necessary in order to design a miniaturized system. Several antennas with different characteristics are proposed in the second stage. Firstly, ultra-wideband microstrip antennas printed on a thin substrate with a thickness of 0.2 mm are designed for both half-wave and full-wave wideband RF energy scavenging. Ambient RF power is distributed over a wide range of frequency bands. A wideband RF energy scavenging system can extract power from different frequencies to maximize the input power, hence, generating sufficient output power for charging devices. Wideband operation with 4 GHz bandwidth is obtained by the proposed microstrip antenna. Secondly, multi-band planar inverted-F antennas with low profile are proposed for frequency bands of GSM 900, DCS 1800 and Wi-Fi 2.4 GHz, which are the three most promising frequency bands for RF energy scavenging. Compared with previous designs, the triple band antenna has smaller dimensions with higher antenna gain. Thirdly, a novel miniature inverted-F antenna without empty space covering Wi-Fi 2.4 GHz frequency band is presented dedicated for indoor RF energy scavenging. The antenna has dimensions of only 10 × 5 × 3.5 mm3 with appreciable efficiency across the operating frequency range. In the final stage, a passive CMOS charge pump rectifier in 0.35 μm CMOS technology is proposed for AC to DC conversion. Bootstrapping capacitors are employed to reduce the effective threshold voltage drop of the selected MOS transistors. Transistor sizes are optimized to be 200/0.5 μm. The proposed rectifier achieves improvements in both power conversion efficiency and voltage conversion efficiency compared with conventional designs. The design strategies proposed in this thesis contribute towards the realization of miniaturized RF energy scavenging systems.

L'amélioration de l'autonomie énergétique des systèmes communicants constitue aujourd'hui une des préoccupations majeures pour leur déploiement massif dans notre environnement. On souhaite rendre complètement autonome ces dispositifs électroniques (on pense entre autres aux capteurs et réseaux de capteurs) en s'affranchissant des sources d'énergie embarquées qui nécessitent des opérations de remplacement ou de recharge périodiques. Parmi les sources d'énergie disponibles qui peuvent être exploitées, on trouve les ondes électromagnétiques. Le dispositif qui permet de capter cette énergie et la convertir en puissance continue utile est dénommé Rectenna (Rectifying antenna) qui associe une antenne de captation à un circuit de rectification à base de diodes. Les rectennae ont fait l'objet d'un nombre important de communications dans la littérature ces dernières années avec pour fil conducteur, la recherche de performances optimales compte tenu de l'atténuation des ondes électromagnétiques et des faibles niveaux de champ récupérés. C'est dans ce contexte que s'est déroulé ce travail de thèse dont le financement a été assuré par un contrat ANR (REC-EM).Dans ce travail, on s'est attaché à développer, à concevoir et à caractériser expérimentalement des structures planaires qui présentent des propriétés intéressantes :- En terme de polarisations orthogonales, ceci de façon à s'affranchir de l'orientation arbitraire de l'onde incidente à la rectenna. Une rectenna à double polarisation circulaire à 2.45 GHz et à double accès sera réalisée pour, de plus, s'affranchir de la perte de 3 dB lorsque l'onde récupérée est à polarisation linéaire à orientation arbitraire.- En termes de résonances multiples, ceci pour augmenter le niveau de puissance récupérée par l'antenne et optimiser la puissance continue convertie. Une rectenna à double fréquence (1.8 et 2.45 GHz) et à accès unique sera conçue ainsi qu'une rectenna constituée d'un réseau de deux antennes double fréquence.- En terme de réduction de taille en s'affranchissant de l'utilisation du filtre HF entre l'antenne et le circuit de conversion ceci pour l'ensemble des structures rectennae développées dans ce travail. Dans tous les cas, il sera nécessaire de développer le circuit de rectification le plus adapté à la topologie de l'antenne de captation et évaluer la technique de recombinaison optimale coté DC pour s'affranchir au mieux des déséquilibres qui peuvent apparaître entre les voies d'accès de l'antenne. Pour contenir les dimensions de la structure globale, des circuits mono diode seront dimensionnés et réalisés pour chacune des structures. Enfin, on exploitera l'antenne à double polarisation circulaire double accès, dont on cherchera à diminuer les dimensions, pour alimenter un capteur de température à affichage LCD. Pour augmenter le niveau de tension nécessaire au fonctionnement du capteur, nous associerons entre la rectenna et le capteur un convertisseur DC-DC. Il s'agit, dans ce cas, d'un dispositif de gestion d'énergie adapté pour les faibles puissances. Deux convertisseurs seront employés dont celui développé par les laboratoires Ampère de l'Ecole Centrale de Lyon et SATIE à l'ENS Cachan. Ce convertisseur a fait l'objet d'une thèse également financée par l'ANR dans le cadre de ce contrat REC-EM / Improving energy autonomy of communication systems constitutes one of the major concerns for their massive deployment in our environment. We want to make these electronic devices (sensors and sensor networks) completely autonomous, avoiding the embedded energy sources that require replacement operations or periodic charging. Among the available energy sources that can be harvested, there are electromagnetic waves. The device that can capture this energy and convert it into useful DC power is called Rectenna (Rectifying antenna), combining antenna with diode-based rectifier. In recent few years, rectennas have reached a significant number of papers in the literature. The main challenge consists in improving performances in term of efficiency, in an attempt to overcome the electromagnetic wave attenuation and the low available field level. According to this context, this PhD work supported by the ANR project REC-EM has taken place. In this study, we have developed, designed and characterized planar structures that have interesting properties:- In term of orthogonal polarizations, so energy harvesting becomes feasable regardless the arbitrary orientation of the incident wave on the rectenna. A dual-circularly polarized rectenna at 2.45 GHz with dual-access will be set up to overcome the 3 dB power loss in the case of linearly-polarized incident wave with unknown orientation.- In term of multiple resonances, so the amount of total RF power collected by the antenna can be increased and consequently the converted DC power level can also be improved. A dual-frequency rectenna (1.8 and 2.45 GHz) with single access will be designed, as well as a rectenna based upon a dual-frequency antenna array.- In term of size compactness by avoiding the use of the HF filter between the antenna and the rectifier for all developed rectenna structures during this work. In all cases, it will be necessary to define the most suitable rectifier topology to each antenna and select, if it is appropriated, the optimum DC recombination technique to overcome the effects of RF power imbalance that may occur between the different antenna accesses. Besides, single-diode circuits will be designed and fulfilled for each structure. Finally, we will miniaturize the dual-circularly polarized dual-access antenna, and exploit it to power a LCD display temperature sensor. To enhance the DC voltage level required to activate the sensor, a DC-DC converter is inserted between the rectenna and the sensor. Such energy management device should be able to operate under low delivered DC power. Two converters will be used. The first one is developed by Ampere Lab at Ecole Centrale de Lyon and SATIE Lab at ENS Cachan. This converter was the subject of another dissertation also supported by the ANR under the REC-EM project

Made available in DSpace on 2014-06-12T17:41:04Z (GMT). No. of bitstreams: 2 arquivo7526_1.pdf: 7264753 bytes, checksum: 764085c312809041966e34bffa171d8d (MD5) license.txt: 1748 bytes, checksum: 8a4605be74aa9ea9d79846c1fba20a33 (MD5) Previous issue date: 2010 / Esta dissertação descreve o projeto de dois amplificadores de baixo ruído (LNA), que é um dos blocos mais relevantes do sistema de recepção de rádio frequencia. Os circuitos, desenvolvidos em tecnologia CMOS 0,35 m da (Austria Micro System), foram baseados na norma IEEE 802.15.4 para serem aplicados a sistemas de redes de sensores sem fio. Apresenta-se uma dedução detalhada do fator de ruído para a configuração de fonte comum com degeneração indutiva, incluindo o ruído induzido no gate e o ruído devido a resistência parasita do gate, bem como duas adaptações de uma técnica de otimização para a figura de ruído em função do tamanho do transistor e da indutância de gate. Por fim, são apresentados dois casos de testes para operar em 915 MHz com seus desempenhos vericados através de simulações

This thesis work builds on the concept of reconfiguring the antenna properties (frequency, polarization, radiation pattern) using Radio Frequency (RF) Micro Electro Mechanical Systems (MEMS). This is a part of the overall research performed at the RF Micro/Nano Electro Mechanical Systems (uNeMS) Laboratory at Utah State University, which includes design, microfabrication, test, and characterization of uNeMS integrated cognitive wireless communication systems (Appendix A). In the first step, a compact and broadband Planar Inverted F Antenna (PIFA) is designed with a goal to accommodate reconfigurability at a later stage. Then, a Frequency Reconfigurable Antenna (FRA) is designed using MEMS switches to switch between the Public Safety (PS) bands, 152-162 MHz and 406-512 MHz, while maintaining the integrity of radiation pattern for each band. Finally, robust mechanical designs of the RF MEMS switches accompanied by different analyses have been performed. These analyses are instrumental in obtaining high yield, reliable, robust microfabrication processes including thin film metal deposition and patterning.

<p>Skew in telecommunication normally means the difference in arrival time of bits transmitted at the same time in differential transmission. As an increasing of transmission data bit rate and more importantly, a data and clock signal rise time of become faster, digital system interconnects became behaving as transmission line. The high speed signals become microwave in nature. The problem is that modern digital designs and verifications require knowledge that has formerly not been needed for a data bit rate of below than 100Mbit but also at the higher frequency range as 5 to 15GHz, however, most references on the necessary subjects are too abstract to be immediately applicable to the skew. For this reason a new method to investigate the skew were introduced, and with which, test board were measured. Since the test boards are made in devise material, and lines on the boards are configured out in distinct structures. In this paper, several methods were applied to find out the skew, and by comparing the results, it could be found that how factors affect the skew, not only the material factor, but some manufactory reason.</p>