Global ETD Search

1	A Possibilistic Approach to Rotorcraft Design through a Multi-Objective Evolutionary Algorithm Chae, Han Gil 24 August 2006 (has links) A method to find solutions to multi-objective design problems that involve poor information available was proposed. The method quantified the designers intuition in a systematic manner, and utilized it to approximate inaccurate and/or vague numbers. In the context of possibility theory, uncertain values were expressed through possibility distributions, i.e. fuzzy membership functions. Based on the membership functions of the value, levels of confidence of the solutions to multi-objective problems were defined through the notions of possibility and necessity. An evolutionary algorithm was modified to find sets of solutions that allow certain levels of confidence instead of the crisp sets of the solutions. The method was applied to a design problem of the gyrodyne configuration and sets of the solutions of the specified possibility and necessity were found. The results of the design problem and the suggestions for future research were discussed. Possibility Evolutionary algorithm Genetic algorithms Rotorcraft design Tip-jet drive system
2	An integrated product – process development (IPPD) based approach for rotorcraft drive system sizing, synthesis and design optimization Ashok, Sylvester Vikram 20 September 2013 (has links) Engineering design may be viewed as a decision making process that supports design tradeoffs. The designer makes decisions based on information available and engineering judgment. The designer determines the direction in which the design must proceed, the procedures that need to be adopted, and develops a strategy to perform successive decisions. The design is only as good as the decisions made, which is in turn dependent on the information available. Information is time and process dependent. This thesis work focuses on developing a coherent bottom-up framework and methodology to improve information transfer and decision making while designing complex systems. The rotorcraft drive system is used as a test system for this methodology. The traditional serial design approach required the information from one discipline and/or process in order to proceed with the subsequent design phase. The Systems Engineering (SE) implementation of Concurrent Engineering (CE) and Integrated Product and Process Development (IPPD) processes tries to alleviate this problem by allowing design processes to be performed in parallel and collaboratively. The biggest challenge in implementing Concurrent Engineering is the availability of information when dealing with complex systems such as aerospace systems. The information is often incomplete, with large amounts of uncertainties around the requirements, constraints and system objectives. As complexity increases, the design process starts trending back towards a serial design approach. The gap in information can be overcome by either “softening” the requirements to be adaptable to variation in information or to delay the decision. Delayed decisions lead to expensive modifications and longer product design lifecycle. Digitization of IPPD tools for complex system enables the system to be more adaptable to changing requirements. Design can proceed with “soft” information and decisions adapted as information becomes available even at early stages. The advent of modern day computing has made digitization and automation possible and feasible in engineering. Automation has demonstrated superior capability in design cycle efficiency [1]. When a digitized framework is enhanced through automation, design can be made adaptable without the requirement for human interaction. This can increase productivity, and reduce design time and associated cost. An important aspect in making digitization feasible is having the availability of parameterized Computer Aided Design (CAD) geometry [2]. The CAD geometry gives the design a physical form that can interact with other disciplines and geometries. Central common CAD database allows other disciplines to access information and extract requirements; this feature is of immense importance while performing systems syntheses. Through database management using a Product Lifecycle Management (PLM) system, Integrated Product Teams (IPTs) can exchange information between disciplines and develop new designs more efficiently by collaborating more and from far [3]. This thesis focuses on the challenges associated with automation and digitization of design. Making more information available earlier goes jointly with making the design adaptable to new information. Using digitized sizing, synthesis, cost analysis and integration, the drive system design is brought in to early design. With modularity as the objective, information transfer is made streamlined through the use of a software integration suite. Using parametric CAD tools, a novel ‘Fully-Relational Design’ framework is developed where geometry and design are adaptable to related geometry and requirement changes. During conceptual and preliminary design stages, the airframe goes through many stages of modifications and refinement; these changes affect the sub-system requirements and its design optimum. A fully-relational design framework takes this into account to create interfaces between disciplines. A novel aspect of the fully-relational design methodology is to include geometry, spacing and volume requirements in the system design process. Enabling fully-relational design has certain challenges, requiring suitable optimization and analysis automation. Also it is important to ensure that the process does not get overly complicated. So the method is required to possess the capability to intelligently propagate change. There is a need for suitable optimization techniques to approach gear train type design problems, where the design variables are discrete in nature and the values a variables can assume is a result of cascading effects of other variables. A heuristic optimization method is developed to analyze this multimodal problem. Experiments are setup to study constraint dependencies, constraint-handling penalty methods, algorithm tuning factors and innovative techniques to improve the performance of the algorithm. Inclusion of higher fidelity analysis in early design is an important element of this research. Higher fidelity analyses such as nonlinear contact Finite Element Analysis (FEA) are useful in defining true implied stresses and developing rating modification factors. The use of Topology Optimization (TO) using Finite Element Methods (FEM) is proposed here to study excess material removal in the gear web region. IPPD Systems engineering Concurrent engineering Drive system design Rotorcraft design Flexibility Relational design Helicopters Flight control Aerodynamics Engineering design Combinatorial optimization Multidisciplinary design optimization Concurrent engineering
3	A plm implementation for aerospace systems engineering-conceptual rotorcraft design Hart, Peter Bartholomew 08 April 2009 (has links) The thesis will discuss the Systems Engineering phase of an original Conceptual Design Engineering Methodology for Aerospace Engineering-Vehicle Synthesis. This iterative phase is shown to benefit from digitization of Integrated Product&Process Design (IPPD) activities, through the application of Product Lifecycle Management (PLM) technologies. Requirements analysis through the use of Quality Function Deployment (QFD) and 7 MaP tools is explored as an illustration. A "Requirements Data Manager" (RDM) is used to show the ability to reduce the time and cost to design for both new and legacy/derivative designs. Here the COTS tool Teamcenter Systems Engineering (TCSE) is used as the RDM. The utility of the new methodology is explored through consideration of a legacy RFP based vehicle design proposal and associated aerospace engineering. The 2001 American Helicopter Society (AHS) 18th Student Design Competition RFP is considered as a starting point for the Systems Engineering phase. A Conceptual Design Engineering activity was conducted in 2000/2001 by Graduate students (including the author) in Rotorcraft Engineering at the Daniel Guggenheim School of Aerospace Engineering at the Georgia Institute of Technology, Atlanta GA. This resulted in the "Kingfisher" vehicle design, an advanced search and rescue rotorcraft capable of performing the "Perfect Storm" mission, from the movie of the same name. The associated requirements, architectures, and work breakdown structure data sets for the Kingfisher are used to relate the capabilities of the proposed Integrated Digital Environment (IDE). The IDE is discussed as a repository for legacy knowledge capture, management, and design template creation. A primary thesis theme is to promote the automation of the up-front conceptual definition of complex systems, specifically aerospace vehicles, while anticipating downstream preliminary and full spectrum lifecycle design activities. The thesis forms a basis for additional discussions of PLM tool integration across the engineering, manufacturing, MRO and EOL lifecycle phases to support business management processes. Teamcenter systems engineering Teamcenter community Teamcenter unified Teamcenter engineering Teamcenter manufacturing CATIA V5 Rotorcraft design Boeing AHS Joint heavy lift VPLM MBOM EBOM Product change control Product definition Configuration management Product structure architecture Design engineering Aerospace engineering System engineering PLM CIE IDE SE Affordability Cost savings Executive helicopter Joint chiefs of staff Marine CAE CAD CAM CAA MDO RSM DOE Consulting Engineering management Perfect storm Engineering software Requirements data management CATIA V4 NX Engineering communications RFP Digitization Air Force Navy Army BAMS FIPER ACSYNT Sikorsky Bell Georgia Tech Engineering methodology Requirements engineering System engineering Search Rescue IDE Integrated digital environment Kingfisher Search and rescue Helicopter Helicopter engineering QFD Legacy design IPPD Quality engineering Defense systems acquisition Coast Guard Decision support systems Rotors (Helicopters) Design Concurrent engineering

1

Page generated in 0.0568 seconds