L'étude détaillée des distributions transverses du halo du faisceau est importante du point de vue des pertes de faisceau et du contrôle du bruit de fond dans ATF2 et les futurs collisionneurs linéaires (FLC). Un nouveau type de capteur diamant sous vide (DSv) déplacable, avec quatre pistes, a été conçu et développé pour la mesure des distributions transverses du halo du faisceau et la détection du spectre des électrons de recul Compton après le point d'interaction (IP) d'ATF2, qui est un prototype à basse énergie (1.3 GeV) de la section de focalisation finale pour les projets de collisionneurs linéaires ILC et CLIC.Cette thèse présente les études du halo du faisceau et des électrons de recul Compton, ainsi que la caractérisation, les études de performance et les tests des capteurs diamant (DS), tant sur PHIL, un photo-injecteur à basse énergie (<10 MeV) au LAL, que sur ATF2. Les résultats des premières mesures du halo du faisceau, utilisant des wire scanner (WS) et un DSv, sur ATF2 sont également présentés et comparés dans cette thèse.Des simulations utilisant Mad-X et CAIN ont été réalisées afin d'estimer le nombre d'électrons composant le halo du faisceau ainsi que le nombre d'électrons de recul Compton. Les résultats des simulations ont indiqué qu'une grande gamme dynamique, supérieure 10⁶ , est nécessaire pour une mesure simultanée du cœur du faisceau, du halo du faisceau et des électrons de recul Compton. Un DSv mono-cristallin, fabriqué par CVD (Chemical Vapor Deposition), a été développé dans ce but.Avant l'installation du capteur diamant, une première tentative de mesure du halo du faisceau a été effectuée en 2013, en utilisant les wire scanners (WS) actuellement installés sur ATF2. En raison de leur dynamique limitée de ~10³ , la distribution du halo du faisceau a été mesurée seulement jusqu'à ~±6σ dans la ligne d'extraction (EXT). Un paramétrage des distributions mesurées du halo du faisceau a montré que les distributions mesurées sont cohérentes avec des mesures faites précédemment, en 2005, sur l'ancienne ligne faisceau d'ATF. Durant ces mesures, une distribution asymétrique du halo vertical du faisceau a été observée pour la première fois en utilisant le WS situé après l'IP, son origine est actuellement sous investigation en utilisant le DSv.Des études pour caractériser des capteurs diamants de dimensions 4.5x4.5x0.5 mm³ ont été réalisées en utilisant des sources α et β. Les paramètres de transport des porteurs de charge (durée de vie, vitesse de saturation, etc.) ont été obtenus en utilisant la technique des courants transitoires (TCT). Par ailleurs, la linéarité de la réponse du DS a été testée sur PHIL avec différentes intensités de faisceau après la fenêtre de sortie de d'accélération. Un signal maximum de 10⁸ électrons a été mesuré, avec une réponse linéaire jusqu'à 10⁷ électrons. Des études similaires de la linéarité ont été faites pour le DSv sur ATF2. Nous avons pu y exploiter avec succès, pour la première fois une gamme dynamique de ~10⁶ , permettant de mesurer simultanément le cœur du faisceau (~10⁹ électrons) et le halo du faisceau (~10³ électrons). Le pick-up électromagnétique induit par le passage du cœur du faisceau et des effets de saturation, qui sont les limitations empêchant actuellement le DSv d'atteindre une gamme dynamique supérieure à 10⁶ , ont également été identifiés et étudiés.Les premières mesures de la distribution horizontale du halo, en utilisant le DSv, ont été effectuées jusqu'à ~±20σx , et ont permis de prouver que le halo du faisceau est collimaté par les ouvertures de la ligne ATF2. Une distribution horizontale du halo compatible avec les paramétrages de 2005 et 2013 a été confirmée. La possibilité de détecter les électrons de recul Compton a été étudiée. Différentes solutions pour accroître la sensibilité des mesures ont été proposées. / The investigation of beam halo transverse distributions is an important issue for beam losses and background control in ATF2 and in Future Linear Colliders (FLC). A novel in vacuum diamond sensor (DSv) scanner with four strips has been designed and developed for the investigation of beam halo transverse distributions and also for the diagnostics of Compton recoil electrons after the interaction point (IP) of ATF2, a low energy (1.3 GeV) prototype of the final focus system for ILC and CLIC linear collider projects. This thesis presents the beam halo and Compton recoil electrons studies as well as the characterization, performance studies and tests of the diamond sensors (DS) both at PHIL, a low energy (<10 MeV) photo-injector at LAL, and at ATF2. First beam halo measurement results using wire scanners (WS) and DSv at ATF2 are also presented and compared in this thesis. Simulations using Mad-X and CAIN were done to estimate the rate of the beam halo and Compton recoil electrons. Simulation results have indicated that a large dynamic range of more than 10⁶ is needed for a simultaneous measurement of the beam core, beam halo and Compton recoil electrons. A single crystalline Chemical Vapor-Deposition (sCVD) based DSv was developed for this purpose. Prior to the diamond detector installation, first attempt of beam halo measurements have been performed in 2013 using the currently installed WS. With a limited dynamic range of ~10³ , the beam halo distribution was measured only up to ~±6σ in the extraction (EXT) line. Parametrizations of the measured beam halo distribution showed a consistent distribution with previous measurements done in 2005 at the old ATF beam line. Meanwhile, an asymmetric vertical beam halo distribution was observed for the first time using the post-IP WS, the origin of which is currently under investigation using the DSv.Studies to characterize DS pads with dimensions of 4.5x4.5x0.5 mm³ were carried out using the α and β sources. Charge carrier transport parameters (lifetime, saturation velocity etc.) were obtained using the transient-current technique (TCT). Furthermore, the linearity of the DS response was tested at PHIL with different beam intensities in air: a maximum signal of 108 electrons was measured with a linear response up to 10⁷ electrons. Similar linearity studies were done for the DSv at ATF2, where we have successfully demonstrated and confirmed for the first time a dynamic range of ~10⁶ by a simultaneous beam core (~10⁹ e-) and beam halo (~10³ e-) measurement using the DSv. Present limitations due to signal pick-up and saturation effects, which prevent the DSv from reaching a dynamic range higher than 10⁶ , were also studied.First measurements of the horizontal beam halo distribution using the DSv were performed up to ~±20σx, where the beam halo was proved to be collimated by the apertures. Horizontal beam halo distributions consistent with the 2005 and 2013 parametrizations were confirmed. The possibility of probing the Compton recoil electrons has been investigated and different ways to increase their visibility have been proposed.

A elaboração de um programa de gerenciamento de uma rede rodoviária implica na utilização de montantes consideráveis de recursos em sua recuperação e manutenção. Neste cenário, ressalta-se a importância da validação de uma nova tecnologia de avaliação funcional de pavimentos para aplicação em rodovias brasileiras que permita a coleta de informações de forma automática, sem a interferência do profissional, minimizando o tempo de coleta e processamento de dados, reduzindo-se as interferências com o tráfego e garantindo informações de qualidade e de rápida restituição. O presente trabalho tem como objetivo a contribuição para o processo de avaliação funcional de pavimentos através validação de resultados do inventário funcional de pavimentos flexíveis com o emprego do equipamento Pavement Scanner, o que pode ser um novo processo que garanta a integridade, a confiabilidade e a plena restituição das informações para o projeto e programa de gestão de pavimentos. Para tanto, seções-teste foram inventariadas e estudadas, onde avaliou-se as condições funcionais do pavimento de acordo com a metodologia tradicional de avaliação da superfície do pavimento e sob a utilização do equipamento Pavement Scanner. Os resultados obtidos pelos diferentes métodos foram analisados e comparados, buscando-se determinar a variação obtida pelas diferentes técnicas de avaliação do pavimento, além da análise da repetitividade e reprodutividade de cada uma destas técnicas. Adicionalmente, foi estudada a aplicabilidade dos resultados obtidos pelo Pavement Scanner no cálculo do PCI (Índice da Condição do Pavimento, do inglês Pavement Condition Index), que é muito utilizado no exterior e considerado uma ferramenta eficaz na gerência de pavimentos. / The development of a road network management program implies the use of significant amounts of resources in their recovery and maintenance. In this scenario, it emphasizes the importance of validating a new technology of functional Pavement assessment for use in Brazilian highways that allows the automatic collection of information, without the interference of a professional, minimizing the time in collecting and processing of data, reducing interference with traffic and ensuring information quality and fast refund. This study aims to contribute to the process of functional pavement evaluation through the validation of results of the functional inventory of flexible pavements with the use of Pavement Scanner equipment, which can be a new process to ensure the integrity, reliability and full refund of information for the pavement management program. With this purpose, sections-tests were surveyed and studied, in which the functional pavement conditions were evaluated according to the traditional method of pavement surface evaluation and with the use of Pavement Scanner equipment. The results obtained by different methods were analyzed and compared, in order to determine the variation obtained by the different pavement evaluation techniques, in addition to the analysis of repeatability and reproducibility of each of these techniques. Furthermore, it was studied the applicability of the results obtained by Pavement Scanner in the calculation of PCI (Pavement Condition Index), which is widely used abroad and considered an effective tool in pavement management.

Le Trouble de Stress Post-Traumatique (TSPT) est une pathologie fréquente, touchant près de 8 % de la population générale. Cette pathologie psychiatrique s’exprime par un carré symptomatique incluant un syndrome de répétition, d’évitement, une hyperactivation neurovégétative ainsi qu’une altération négative des cognitions et de l’humeur. Un des traitements les plus efficaces dans cette pathologie est une psychothérapie nommée EMDR pour Eye Movement Desensitization and Reprocessing. Bien que cette thérapie ne soit plus à faire la preuve de son efficacité, les mécanismes d’actions de celle-ci demeurent encore aujourd’hui à l’état d’hypothèse. L’objectif de notre travail de thèse fut d’explorer le mécanisme d’action de la thérapie EMDR à travers différents paradigmes en EEG, TEP-scanner et IRMf, en comparant l’activité cérébrale avant et après traitement ou pendant les stimulations bilatérales alternées. Nous avons pu démontrer que la thérapie EMDR modifiait l’activité cérébrale d’un réseau cérébral impliqué dans le traitement émotionnel et la mémoire et d’une structure en particulier, le précuneus. Les stimulations bilatérales alternées qui sous-tendent l’action de l’EMDR activent elles aussi une partie de ce réseau expliquant l’impact de l’EMDR sur la mémoire traumatique. Pour la première fois, nous avons également montré que l’activité du précuneus avant traitement est capable de prédire l’intensité de la diminution des symptômes de TSPT. La durée du sommeil paradoxal avant traitement permet quant à elle de prédire le nombre de séances nécessaires pour obtenir la rémission. / Post-Traumatic Stress Disorder (PTSD) is a common condition affecting nearly 8% of the general population. This psychiatric pathology is expressed by a symptomatic square including a syndrome of repetition, avoidance, neurovegetative hyperactivation and a negative alteration of cognitions and mood. One of the most effective treatments in this pathology is a psychotherapy called EMDR for Eye Movement Desensitization and Reprocessing. Although this therapy no longer needs to prove its effectiveness, its mechanisms of action are still at the hypothesis stage today. The objective of our thesis work was to explore the mechanism of action of EMDR therapy through different paradigms in EEG, PET-scanner and fMRI, comparing brain activity before and after treatment or during bilateral alternating stimuli. We were able to demonstrate that EMDR therapy altered the brain activity of a brain network involved in emotional treatment and memory and of a particular structure, the precuneus. The alternating bilateral stimuli underlying the action of EMDR also activate part of this network explaining the impact of EMDR on traumatic memory. For the first time, we also have shown that the activity of the precuneus before treatment is able to predict the magnitude of the decrease in PTSD symptoms. The length of REM sleep before treatment can predict the number of sessions needed to reach remission.

The pipeline industry has conducted a vast amount of research on the subject of mechanical damage. Mechanical damage makes up a large portion of the total amount of pipeline failures that occur each year. The current methods rely on engineering judgment and experience rather than scientific theory. The method for the assessment of mechanical damage introduced in this study uses a material property called critical strain to predict the onset of cracking within the pipe wall. The critical strain is compared to the strain within a dent using a ductile failure damage indicator (DFDI). To investigate the use of the DFDI to indicate the onset of cracking within a dent, the study attempted to accomplish three tasks. The first was to investigate the use of various techniques to locate the critical strain from the stress-strain curve. Five samples taken from the pipe material was used to generate both engineering and true stress-strain curves. A sensitivity analysis was conducted to show the effects of different variables on the critical strain value. The DFDI compares the critical strain value to the calculated strain at the deepest depth location within a dent. The strain calculations use the curvature of the dent and thus require a dent profile. A high resolution laser scanner was used to extract dent profiles from a pipe. The second task of the study was to investigate the reliability of the laser scanner equipment used for this study. The results from the investigation showed that the laser scanner could be used to scan the inside of the pipe despite its design for external scanning. The results also showed that the scans should be 1 mm in length along the axis of the pipe at a resolution of 0.5 mm and 360 degrees around the pipe. The final task was to conduct the denting test. The test used a spherical indenter to dent the pipe at increments of 3% of the outside diameter. The results from the test showed that a visible crack did not form on the inside pipe surface as expected from the DFDI method. This does not mean a crack did not form. During the denting test distinct popping sounds were observed possibly indicating cracks forming within the pipe wall.

Orientador: Prof. Dr. Mario Alexandre Gazziro / Dissertação (mestrado) - Universidade Federal do ABC, Programa de Pós-Graduação em Ciência da Computação, 2017. / Devido à disseminação de novas tecnologias de varredura (ou escaneamento) 3D, há agora a possibilidade de se realizar uma análise corporal a partir de um modelo tridimensional do paciente. Este trabalho visa criar uma plataforma de avaliação corporal semiautomática para medição de ângulos e distâncias de pontos anatômicos do corpo, juntamente com aplicações que somente informações 3D podem agregar, como a medição do volume do corpo e perímetros de seções corporais, criando-se assim um equipamento completo conhecido como scanner 3D multifuncional. Este equipamento foi construído utilizando 2 sensores Microsoft Kinect aliados à biblioteca de reconstrução ReconstructMe, uma plataforma giratória e um microcontrolador Arduino, criando uma plataforma de escaneamento e software de uso fácil e intuitivo. A plataforma desenvolvida foi utilizada em testes de análise postural de um manequim segundo o protocolo SAPO de avaliação e comparada ao software SAPO. O método de aquisição de modelos tridimensionais foi totalmente automatizado e se mostrou confiável, desde que o usuário permaneça parado durante o processo. O software para avaliações corporais, nomeado AllBodyScan3D, conseguiu reproduzir os métodos propostos e realizar uma avaliação postural de forma ainda não vista em outros trabalhos. A comparação de resultados de avaliação postural do software proposto com o software SAPO mostrou boa correspondência entre os métodos. / Due to the spread of new 3D scanning technologies, there is now the possibility of performing a body analysis from a three-dimensional model of the patient. This work aims to create a semiautomatic body evaluation platform for measuring angles and distances of anatomical points of the body, together with applications that only 3D information can aggregate, such as the measurement of body volume and perimeters of body sections, thus creating a complete equipment known as multifunctional 3D scanner. This equipment was built using 2 Microsoft Kinect sensors together with the ReconstructMe reconstruction library, a turntable and an Arduino microcontroller, creating a scanning platform and an intuitive and easy-to-use software. The developed platform was used in postural analysis tests of a mannequin following the SAPO evaluation protocol and compared to the SAPO software. The method of acquisition of three-dimensional models was fully automated and proved to be reliable, provided that the user remains still during the process. The body evaluation software, named AllBodyScan3D, was able to reproduce the proposed methods and perform a postural evaluation in ways not yet seen in other works. The comparison of postural evaluation results of the proposed software with the SAPO software showed a good match between the methods.

A elaboração de um programa de gerenciamento de uma rede rodoviária implica na utilização de montantes consideráveis de recursos em sua recuperação e manutenção. Neste cenário, ressalta-se a importância da validação de uma nova tecnologia de avaliação funcional de pavimentos para aplicação em rodovias brasileiras que permita a coleta de informações de forma automática, sem a interferência do profissional, minimizando o tempo de coleta e processamento de dados, reduzindo-se as interferências com o tráfego e garantindo informações de qualidade e de rápida restituição. O presente trabalho tem como objetivo a contribuição para o processo de avaliação funcional de pavimentos através validação de resultados do inventário funcional de pavimentos flexíveis com o emprego do equipamento Pavement Scanner, o que pode ser um novo processo que garanta a integridade, a confiabilidade e a plena restituição das informações para o projeto e programa de gestão de pavimentos. Para tanto, seções-teste foram inventariadas e estudadas, onde avaliou-se as condições funcionais do pavimento de acordo com a metodologia tradicional de avaliação da superfície do pavimento e sob a utilização do equipamento Pavement Scanner. Os resultados obtidos pelos diferentes métodos foram analisados e comparados, buscando-se determinar a variação obtida pelas diferentes técnicas de avaliação do pavimento, além da análise da repetitividade e reprodutividade de cada uma destas técnicas. Adicionalmente, foi estudada a aplicabilidade dos resultados obtidos pelo Pavement Scanner no cálculo do PCI (Índice da Condição do Pavimento, do inglês Pavement Condition Index), que é muito utilizado no exterior e considerado uma ferramenta eficaz na gerência de pavimentos. / The development of a road network management program implies the use of significant amounts of resources in their recovery and maintenance. In this scenario, it emphasizes the importance of validating a new technology of functional Pavement assessment for use in Brazilian highways that allows the automatic collection of information, without the interference of a professional, minimizing the time in collecting and processing of data, reducing interference with traffic and ensuring information quality and fast refund. This study aims to contribute to the process of functional pavement evaluation through the validation of results of the functional inventory of flexible pavements with the use of Pavement Scanner equipment, which can be a new process to ensure the integrity, reliability and full refund of information for the pavement management program. With this purpose, sections-tests were surveyed and studied, in which the functional pavement conditions were evaluated according to the traditional method of pavement surface evaluation and with the use of Pavement Scanner equipment. The results obtained by different methods were analyzed and compared, in order to determine the variation obtained by the different pavement evaluation techniques, in addition to the analysis of repeatability and reproducibility of each of these techniques. Furthermore, it was studied the applicability of the results obtained by Pavement Scanner in the calculation of PCI (Pavement Condition Index), which is widely used abroad and considered an effective tool in pavement management.

Submitted by Fernando Souza (fernando@biblioteca.ufpb.br) on 2017-10-04T11:56:00Z No. of bitstreams: 1 arquivototal.pdf: 3127385 bytes, checksum: 642b4f5b14587b1f9a6e45fb220f1cec (MD5) / Made available in DSpace on 2017-10-04T11:56:00Z (GMT). No. of bitstreams: 1 arquivototal.pdf: 3127385 bytes, checksum: 642b4f5b14587b1f9a6e45fb220f1cec (MD5) Previous issue date: 2017-08-02 / Electronic government can be characterized as the use of Information and Communication Technologies by public administration as support for internal government processes and the delivery of government products and services to citizens and industry in a fast and efficient way. It is essential that e-government prevents unauthorized access to ensure that Integrity, Availability and Confidentiality, basic principles of information security, are protected from electronic threats on the Internet. These threats place information assets at constant risk by taking advantage of the various vulnerabilities in the virtual environment where e-government is inserted. Thus, this research aimed to analyze the possible vulnerabilities in egovernment portals of the municipalities of Paraíba State. The 50 municipalities that represent the largest share of the Gross Domestic Product (GDP) of the state of Paraíba were considered as the research population. From these, it was possible to analyze the portals of 40. This research was characterized as a descriptive research, with a Quantitative approach. In order to collect data, we used Nestparker software, a vulnerability scanner whose function is to track and identify vulnerabilities in Web applications. As a result, 822 vulnerabilities were found, of which 15% are Critical and 15% High Criticality. In addition, 10% of the vulnerabilities were classified as Medium Criticality, which, in addition to other vulnerabilities with higher impacts, represents a scenario with more than 40% vulnerabilities found in the portals of the municipalities analyzed. Such vulnerabilities have the potential to allow malicious elements to negatively impact the continuity of the service. In addition to identifying the vulnerabilities of electronic security in e-government portals in the State of Paraíba, this research indicated how to correct the identified problems, which allows public managers to take actions that aim to minimize security breaches and the adoption of security strategies as well as the implementation of an information security policy. / O governo eletrônico pode ser caracterizado como a utilização das Tecnologias de Informação e Comunicação, pela administração pública, como apoio aos processos internos do governo e a entrega de produtos e serviços governamentais aos cidadãos e à indústria de forma célere e eficiente. É fundamental que o governo eletrônico se previna de acessos indevidos a fim de garantir que a Integridade, a Disponibilidade e a Confidencialidade, princípios basilares da segurança da informação, sejam protegidas de ameaças eletrônicas presentes na Internet. Essas ameaças colocam os ativos de informação em constante risco ao se aproveitarem das diversas vulnerabilidades existentes no ambiente virtual onde está inserido o governo eletrônico. Dessa forma, essa pesquisa analisa as possíveis vulnerabilidades existentes em portais de governo eletrônico em municípios do Estado da Paraíba. A população da pesquisa foram os 50 municípios que representam maior participação para a composição do Produto Interno Bruto (PIB) do Estado da Paraíba, sendo possível analisar os portais de 40 municípios. Esta pesquisa caracterizou-se como uma pesquisa descritiva, com abordagem quantitativa. Para a coleta dos dados utilizou-se o software Nestparker, um scanner de vulnerabilidades que tem como função rastrear e identificar vulnerabilidades em aplicações Web. Como resultado, foram encontradas 822 vulnerabilidades, das quais 15% são Críticas e 15% de Alta Criticidade. Além disso, 10% das vulnerabilidades foram classificadas como de Média Criticidade, o que, somada às outras vulnerabilidades de maiores impactos, representa um cenário com mais de 40% de vulnerabilidades encontradas nos portais dos municípios analisados. Tais vulnerabilidades tem o potencial de permitir que elementos mal-intencionados causem impactos negativos relevantes à continuidade do serviço. Essa pesquisa indicou, também, como corrigir os problemas identificados, o que pode permitir aos gestores públicos efetuarem ações que visem minimizar falhas de segurança e a adoção de estratégias de segurança, bem como a implantação de uma política de segurança da informação.

Organização Interamericana de Direitos Humanos - OEA / A interpretação antropológica de instrumentos musicais e do fato cultural que fornece sua fabricação e uso, é relevante para a compreensão da música em sua dimensão simbólica, estética e sensorial. A criação de um instrumento sonoro, permite mostra a importância harmônica e melódica, que produz o instrumento musical, além de estabelecer o contato entre a comunidade pré-hispânica e a paisagem sonora o qual é percebido pelos sentidos. A música na cultura Tumaco, constitue a mostra de um grande grupo das técnicas oleiras para a fabricação de instrumentos musicais, se vislumbrando uma criação útil e simbólica para aqueles artefatos em as sociedades navegantes do Litoral Pacífico Colombiano entre o 300 A.C 300 D.C. Finalmente se escolheram um 23 peças, entre instrumentos e representações musicais, ampliando o âmbito ilustrativo dos artefatos, mostrando o corpo geral externo do instrumento musical; adicionalmente se fizeram provas sonoras de 9 instrumentos musicais, em ótimo estado de conservação, considerando uma percepção visual e sonora contemporânea da sonoridade préhispânica. / La interpretación antropológica de instrumentos musicales y del hecho cultural que propicia su fabricación y uso, es pertinente para la comprensión de la música en su dimensión simbólica, estética y sensorial. La creación de un instrumento sonoro, permite evidenciar la importancia armónica y melódica que produce el instrumento musical, además de establecer el contacto entre la comunidad prehispánica y el entorno sonoro el cual percibe mediante los sentidos. La música en la cultura Tumaco, constituye la evidencia de un gran manejo de las técnicas alfareras para la fabricación de instrumentos musicales, vislumbrándose una creación productiva y simbólica para este tipo de artefactos en sociedades navegantes del Litoral Pacífico Colombiano entre el 300 A.C – 300 D.C. Finalmente se seleccionaron un número de piezas ubicadas en el Museo del oro de Bogotá, de las cuales se realizaron tomas 3D, con scanner Eva Artec 3D de 24 piezas entre instrumentos y representaciones musicales, ampliado el ámbito ilustrativo de las piezas, mostrando el cuerpo general externo de la pieza musical; adicionalmente, se efectuaron pruebas sonoras de 9 instrumentos musicales, en excelente estado de conservación, considerando una perspectiva visual y sonora contemporánea de la sonoridad prehispánica. / Anthropological interpretation of musical instruments and the cultural facts promote their manufacture and use, it's relevant for understand musical, symbolic, aesthetic and sensory dimension. The creation of a sonourus instrument, allow highlight the importance of melodic and harmonic production of musical instrument, on top show the contact between the Pre-Hispanic population and sonourus environment that is perceived by the senses. Music on the Tumaco culture, constitutes evidence of a great technical pottery for the manufacture of musical instruments, glimpse a create production and symbolic for this type of artifacts on the Colombian Pacific coast on sailing communities between 300 BC - 300 AC. Finally was chosen a number of pieces in the Museo del Oro of Bogota of which were took 3D captures with scanner Eva Artec 3D, testing on 24 pieces between instruments and musical representations, broading the illustrative field of the pieces, showing the general body of music artifact. Additionally, it's does tests 9 musical instruments, in excellent conditions, consider a contemporary sound and visual perspective of Pre-Hispanic sound.

Orientadores: Inacio Maria Dal Fabbro, Adilson Machado Enes / Tese (doutorado) - Universidade Estadual de Campinas, Faculdade de Engenharia Agrícola / Made available in DSpace on 2018-08-24T11:36:45Z (GMT). No. of bitstreams: 1 Fracarolli_JulianaAparecida_D.pdf: 5319280 bytes, checksum: 4488936faca98d4c091c7703b2fd0ca0 (MD5) Previous issue date: 2014 / Resumo: Técnicas ópticas vêm sendo utilizadas para diversas finalidades técnicas e científicas. Algumas técnicas ópticas se caracterizam como métodos robustos, de baixo custo, não invasivos e não destrutivos para avaliação de materiais diversos, como produtos agrícolas, havendo aplicações desde a engenharia até a área da saúde humana e animal. Neste trabalho propõem-se a avaliação de frutos através da combinação de duas técnicas ópticas cujos estudos vêm comprovando suas aplicabilidades como métodos alternativos e inovadores, os quais empregam equipamentos de baixo custo na aquisição dos dados, permitindo automação de processos de seleção e classificação de produtos. Uma dessas técnicas é conhecida como Biospeckle, a qual fornece informações referentes à qualidade do material biológico em nível de estruturas celulares e a outra é o escaneamento com linha laser, que permite a obtenção de geometria do objeto nos eixos Xi (i = 1,2,3). O objetivo é proceder a um levantamento topográfico digital de materiais biológicos combinando o posicionamento geométrico dos pontos da imagem com informações referentes à atividade biológica. Foi realizada ainda a diferenciação entre frutos de formato variado, a classificação de frutos por formato, classe, coloração e defeitos por meio de processamento de imagens. Dessa forma é possível observar frutos com irregularidades superficiais, maturidade, danos mecânicos e latentes, entre outros. Esta pode se tornar a base para a seleção automática de produtos agrícolas. Foram utilizados um emissor de linha laser de diodo com 632 nm de comprimento de onda, luz branca difusa, câmera CCD, computador, mesa óptica, mamões, peras, tomates e esferas de isopor, bem como softwares ImageJ, Octave, Matlab. Foram desenvolvidos cinco programas computacionais para processamento das imagens. Foram realizados cinco experimentos, a saber: (1) Avaliação da Maturidade de Frutos; (2) Reconstrução Tridimensional e Mapeamento da Bioatividade; (3) Detecção de Formato Variado; (4) Mapeamento por Formato, Classe e Coloração; (5) Detecção de Defeitos. Na Avaliação da Maturidade foram correlacionados índices de maturidade tradicionais (parâmetros de Hunter L a b, pH, Sólidos Solúveis Totais (SST), a relação Sólidos Solúveis Totais e Acidez Total Titulável (SST/ATT), Módulo de Elasticidade, massa e diâmetro) e a técnica óptica Biospeckle, pelo cálculo do Momento de Inércia (MI). Para a Reconstrução Tridimensional os frutos foram rotacionados através de um motor de passo. A cada passo do motor, o fruto foi iluminado pela linha laser projetada e fotografado para obtenção dos dados de geometria e Biospeckle pelo método LASCA (Laser Speckle Contrast Analysis). Foi analisada a correlação entre os índices de maturidade tradicionais e os valores de MI na avaliação da maturidade. Esta tese mostra que é possível avaliar a maturidade dos frutos através do Biospeckle. Obteve-se um mapa tridimensional que integra as informações de topografia e bioatividade do fruto. Obteve-se, ainda, a detecção de formato variado, a classificação de frutos por mapeamento por formato, classe e coloração e detecção de defeitos através de software / Abstract: Optical techniques have been used for both technical and scientific purposes. Optical techniques are usually characterized as being robust, inexpensive, non-invasive and non-destructive methods in to evaluate a diversity of materials which include agricultural derived products. It also shows applications ranging from engineering to human and animal health. In this doctoral dissertation, a new technique to evaluate some fruit properties is proposed. It combines two optical techniques (i.e. Biospeckle and Scan-line laser) whose applicability has been demonstrated as being alternative and innovative. The new proposed technique allows low-cost data acquisition, automation of the entire process, and a proper selection and classification method of vegetable bodies (e.g. fruits). Biospeckle allows obtaining information regarding the quality level of biological material into cellular structures. Scan-line laser enables the attainment of the object geometry on the axes Xi (i=1,2,3). The main purpose of this doctoral dissertation is to obtain a digital survey of biological materials (i.e. papaya, pear and tomato) integrating both geometric positioning and information concerning to its biological activity. The differentiation between different fruit shapes, fruit sorting by size, class, color and defects through image processing was also carried out. Thus it was also possible to observe fruits with surface irregularities, maturity, and mechanical damage, among others. This is the basis proposed for the automatic selection of agricultural products. The following materials were employed in the tests: a line-emitting diode laser with a wavelength of 632 nm, diffuse white light, CCD camera, computer, optical table, papaya, pear and tomato fruits and polystyrene spheres. The softwares utilized were: ImageJ, Octave, Matlab. A total of five computer programs were developed for the image processing procedures. Five experiments were performed: (1) Maturity Assessment of Fruits; (2) Three Dimensional Reconstruction and Mapping of Bioactivity; (3) Miscellaneous Format Detection; (4) Mapping Format, Class and Coloration; (5) Defect Detection. In Maturity Assessment there were correlated traditional methods to verify the maturity (the Hunter parameters L a b, pH, Total Soluble Solids (TSS), the relationship between Total Soluble Solids and Titratable Acidity (TSS/TA), Modulus of Elasticity, weight and diameter) and the optical technique Biospeckle by calculating the Moment of Inertia (MI). For the Three Dimensional Reconstruction the fruits were rotated by a stepper motor. At every step of the motor, the fruit was illuminated by the projected laser line and photographed in order to obtain both geometric and biospeckle data by the LASCA (Laser Speckle Contrast Analysis) method. The correlation between traditional methods for the maturity assessment and values of MI was analyzed. This doctoral dissertation shows that it is possible to evaluate the maturity of fruits through Biospeckle. A three-dimensional map that includes topographical information and bioactivity of the fruit was generated. Also a software can now detect variations in size, classify fruit shapes, color and class as well as defect detection efficiently. / Doutorado / Maquinas Agricolas / Doutora em Engenharia Agrícola

The aim of this thesis is to create a system, which draws the graphics with the help of a set laser project and eventually is able to synthetize several coloured rays and thus realise a multicolour drawing. The whole system is controlled by a Raspberry PI microcomputer and the data is sent to it from a PC via an Ethernet cable. The transmission of the projector device was identified and possible ways of improving the device were suggested. The results of this thesis allow creation of a multi-coloured vector picture, transferring it into the device and depiction on the project desktop. The whole device can therefore be used for example for the purpose of a presentation.