Automotive companies are actively pursuing to increase the use of high-strength-lightweight alloys such as aluminum, magnesium, and advanced/ultra high-strength steels (A/UHSS) in body panel and structural part applications to achieve fuel efficiency while satisfying several environmental and safety concerns. A/UHSS sheet materials with higher strength and crashworthiness capabilities, in comparison to mild steel alloys, are considered as a near-term (i.e., ~5 years) choice of material for body and structural components due to their relatively low cost when compared with other lightweight materials such as aluminum and magnesium. However, A/UHSS materials present an increased level of die wear and springback in stamping operations when compared to the currently used mild steel alloys due to their higher surface hardness and high yield strength levels. In order to prevent the excessive wear effect in stamping dies, various countermeasures have been proposed such as alternative coatings, modified surface enhancements in addition to the use of newer die materials including cast, cold work tool, and powder metallurgical tool steels. In this study, a new die wear test method was developed and tested to provide a cost-effective solution for evaluating various combinations of newly developed die materials, coatings and surfaces accurately and rapidly. A new slider type of test system was developed to replicate the actual stamping conditions including the contact pressure state, sliding velocity level and continuous and fresh contact pairs (blank-die surfaces). Several alternative die materials in coated or uncoated conditions were tested against different AHSS sheet blanks under varying load, sliding velocity circumstances. Prior to and after wear tests, several measurements and tribological examinations were performed to obtain a quantified performance evaluation using commonly adapted wear models. Analyses showed that (1) the rapid wear method is feasible and results in reasonable wear assessments, (2) uncoated die materials are prone to expose severe form wear (galling, scoring, etc.) problems; (3) coated samples are unlikely to experience such excessive wear problems, as expected; (4) almost all of the the recently developed die materials (DC 53, Vancron 40, Vanadis 4) performed better when compared to conventional tool steel material AISI D2, and (5) in terms of coating type, die materials coated with thermal diffusion (TD) and chemical vapor deposition (CVD) coatings performed relatively better compared to other tested coating types; (6) It was seen that wear resistance correlated with substrate hardness.

After the review of the basic theory of the inverse method, a new modified arc-length search method is proposed to find better initial solution. The methods to deal with the vertical walls are also discussed and presented. Then, a generalized multi-step inverse FEM method is proposed. It solves two key obstacles: the first one is to determine the initial solution of the intermediate three-dimensional configurations and the other is to control the movement of nodes so they could only slide on constraint surfaces during the search by Newton-Raphson iteration. The computer implementation of the generalized multi-step inverse FEM is also presented. By comparing to the simulation results using a commercial software system, the effectiveness of the new method is validated. / Currently, there are a number of commercial FEM software systems available in the market. These software systems are based on an incremental FEM process that models the sheet metal stamping process in small incremental steps. Even though the incremental FEM is accurate, it is not suitable for the initial conceptual design for its needing of detailed design parameters and enormous calculation times. As a result, another type of FEM, called the inverse FEM method or one-step FEM method, has been proposed. While it is less accurate than that of the incremental method, this method requires much less computation and hence, has a great potential. However, it also faces a number of unsolved problems, which limits its application. This motivates the presented research. / From a physical point of view, the formability and the quality of a product are influenced by several factors. The design of the product in the initial stage and the motion of the press during the production stage are two of these crucial factors. This thesis focuses on the numerical simulation for these two factors using FEM. / Other than the product design, the punch motion (including punch speed and punch trajectory) of the stamping press also has significant effect on the formability and the quality of the product. In fact, this is one of the major reasons why hydraulic presses and/or servo presses are used for parts which demand high quality. In order to reveal the quantitative correlation between the punch motion and the part quality, the Cowper-Symonds strain rate constitutive model and the implicit dynamic incremental FEM are combined to conduct the research. The effects of the punch motion on the part quality, especially the plastic strain distribution and the potential springback, have been investigated for the deep drawing and the bending processes respectively. A qualitative relationship between the punch motion and the part quality is also derived. / The reaction force of the punch motion causes the dynamic deformation of the press during the stamping, which in turn influences the part quality as well. This dynamic information, in the form of the strain signal, is an important basis for the on-line monitoring of the part quality. By using the actual force as the input to the press, the incremental FEM is needed to predict the strain of the press. The result is validated by means of experiments and can be used to assist the on-line monitoring. / The sheet metal stamping process plays an important role in modern industry. With the ever-increasing demand for shape complexity, product quality and new materials, the traditional trial and error method for setting up a sheet metal stamping process is no longer efficient. As a result, the Finite Element Modeling (FEM) method has now been widely used. / Huang Ying. / "March 2006." / Adviser: Ruxu Du. / Source: Dissertation Abstracts International, Volume: 67-11, Section: B, page: 6694. / Thesis (Ph.D.)--Chinese University of Hong Kong, 2006. / Includes bibliographical references (p. 141-160). / Electronic reproduction. Hong Kong : Chinese University of Hong Kong, [2012] System requirements: Adobe Acrobat Reader. Available via World Wide Web. / Electronic reproduction. [Ann Arbor, MI] : ProQuest Information and Learning, [200-] System requirements: Adobe Acrobat Reader. Available via World Wide Web. / Abstracts in English and Chinese. / School code: 1307.

Novos tratamentos térmicos e a otimização dos processos de conformação têm contribuído para o desenvolvimento de microestruturas multifásicas com excelente combinação de ductilidade e resistência mecânica. Parte dessa melhoria depende da presença de austenita retida, de sua estabilidade e fração volumétrica. O presente trabalho tem como objetivo caracterizar a evolução da microestrutura e comportamento das propriedades mecânicas do aço dual phase classe 600 (DP 600), após tratamentos térmicos intercríticos de têmpera e partição (Q&P) e reversão da martensita, assim como tratamentos termomecânicos de simulação física da estampagem a quente (HS), variando a deformação em 10% (HS 10) e 30% (HS 30), e combinando estampagem a quente com subsequente tratamento de têmpera e partição (HSQ&P). Duas condições microestruturais de partida diferentes foram utilizadas nos tratamentos térmicos. Para os tratamentos térmicos e termomecânicos Q&P, HS e HSQ&P a microestrutura de partida foi a bifásica (ferrita e martensita). Já para o tratamento térmico de reversão a microestrutura de partida foi modificada para martensítica. Os tratamentos puramente térmicos foram realizados no dilatômetro Bähr do Laboratório de Transformações de Fase (LTF); entretanto, os tratamentos termomecânicos foram feitos no simulador termomecânico Gleeble®, acoplado à linha de difração de raios X (XTMS) do Laboratório Nacional de Nanotecnologia (LNNano). A análise microestrutural foi feita com suporte de microscopia ótica (MO) e eletrônica de varredura (MEV-FEG), EBSD, e difração de raios X in situ e convencional. Avaliaram-se as propriedades mecânicas por ensaio de tração em corpos de prova sub-size e endentação instrumentada. As amostras Q&P, HS e HSQ&P foram submetidas a ensaios exploratórios de resistência ao trincamento por hidrogênio (HIC) segundo a norma NACE TM0284. Adicionalmente, foi feita a medição de hidrogênio ancorado na microestrutura estudada, após tratamentos, utilizando a técnica de dessorção térmica disponível no LNNano. A avaliação das mudanças microestruturais e de propriedades mecânicas após tratamentos térmicos foram discutidas separadamente para cada microestrutura de partida. Os resultados dos processos Q&P, HS e HSQ&P no aço, mostraram que a evolução da microestrutura levou a formação de uma microestrutura mais complexa do que a microestrutura ferrítico-martensítica simples do material como recebido. A complexa microestrutura é dada pela formação de ferrita epitaxial durante a etapa de tratamento intercrítico, ferrita induzida por deformação (DIFT) na etapa de deformação em alta temperatura e bainita na etapa de partição. Essa mistura microestrutural levou a variações na relação das frações volumétricas de ferrita e martensita em relação às frações iniciais do aço, assim como na presença de austenita retida e sua estabilidade. Com base nos resultados é possível afirmar que o processo Q&P produz um aumento nas propriedades mecânicas do material. Por outro lado, após o ensaio de HIC todas as amostras apresentaram susceptibilidade ao trincamento; contudo, a severidade do dano foi maior nas amostras deformadas HS 30. Os ensaios preliminares de dessorção mostraram maior aprisionamento de hidrogênio em armadilhas reversíveis nas amostras HSQ&P e irreversíveis na amostra HS 30. Na segunda parte, os resultados do tratamento de reversão sugerem que, em geral, a microestrutura do aço processado compreende uma morfologia em ripas de ferrita intercrítica, martensita e filmes de austenita retida. A maior temperatura de reversão intercrítica resultou em menor fração de ferrita intercrítica. Por outro lado, a temperatura intercrítica de reversão influenciou significativamente a estabilidade da austenita retida. Uma alta fração de austenita retida foi obtida a uma temperatura ligeiramente acima da temperatura Ac1. Um segundo ciclo de reversão promoveu a difusão de C e Mn para a austenita revertida tornando-a mais estável a temperatura ambiente. / Novel Heat Treatments and the optimization of the forming processes have contributed to the development of multiphase microstructures with attractive combinations of ductility and mechanical resistance. This improvement partially depends on the presence, stability and volume fraction of retained austenite. The objective of this work is to characterize the evolution of the microstructure and mechanical properties of a class 600 dual phase steel (DP 600), as a function of the thermal and thermomechanical history. Two initial microstructures were used in this study. A ferritic-martensitic microstructure was used as the starting condition for inter-critical heat treatments followed by quenching and partitioning (Q&P) and for the thermomechanical simulations of the hot stamping (HS) process. The latter applying deformations of 10% (HS 10) and 30% (HS 30) combining hot stamping with subsequent quenching and partition (HSQ&P). The thermal cycles were performed in a Bähr dilatometer at the Laboratory of Phase Transformations (LTF), then duplicated using a Gleeble® thermomechanical simulator, coupled to the X-ray Scattering and Thermo-mechanical Simulation beamline (XTMS) at the Brazilian Nanotechnology National Laboratory (LNNano). The microstructural analysis was performed using optical microscopy (MO) and scanning electron (SEM-FEG), Electron Backscatter Diffraction (EBSD), and in situ and conventional X-ray diffraction. The mechanical properties were evaluated by tensile testing on sub-size specimens and by instrumented macro-nano indentation tests. The evolution of the microstructure and mechanical properties for each starting microstructure was discussed separately. The Q&P, HS and HSQ&P samples were submitted to exploratory tests of resistance to hydrogen induced cracking (HIC) according to NACE TM0284. Additionally, hydrogen measurements were performed for the microstructures obtained after Q&P and HDQ&P using the thermal desorption technique at LNNano. After Q&P, HS and HSQ&P, the resultant microstructure was more complex than the as-received ferritic-martensitic condition. Such complexity comes from the formation of epitaxial ferrite from the former ferritic phase during the intercritical treatment step, the deformation induced ferrite (DIFT) and the bainite formation during the partitioning step. This led to variations in the volumetric fraction of ferrite and martensite in relation to the initial fractions of the as-received condition, as well as the presence of retained austenite and its stability upon cooling. The Q&P process increased the mechanical properties of the material. On the other hand, all microstructures showed susceptibility to hydrogen cracking after 72 hours of H2S exposure tests. However, the damage was more severe for the HS samples with 30% of deformation. The preliminary desorption tests showed greater hydrogen trapping in reversible traps after HSQ&P and in irreversible traps for the HS with 30% deformation. A second set of experiments was conducted for a different microstructure consisting of a fully martensitic matrix as the initial condition. After intercritical reversion, the resultant microstructure comprised intercritical lath-like ferrite, martensite laths and retained austenite films. The higher the intercritical reversion temperature, the smaller the fraction of intercritical ferrite. On the other hand, the transformation temperature significantly influenced the stability of the retained austenite. The highest fraction of retained austenite was obtained when the transformation occurred slightly above the Ac1 temperature. A double intercritical reversion cycle promoted the diffusion of C and Mn to the reversed austenite making it more stable upon cooling to room temperature, leading to a better combination of strength and ductility.

The current work used discrete event simulation techniques to model the economics of quality within an actual automotive stamping plant. Automotive stamping is a complex, capital intensive process requiring part-specific tooling and specialised machinery. Quality control and quality improvement is difficult in the stamping environment due to the general lack of process understanding and the large number to interacting variables. These factors have prevented the widespread use of statistical process control. In this work, a model of the quality control techniques used at the Ford Geelong Stamping plant is developed and indirectly validated against results from production. To date, most discrete event models are of systems where the quality control process is clearly defined by the rules of statistical process control. However, the quality control technique used within the stamping plant is for the operator to perform a 100% visual inspection while unloading the finished panels. In the developed model, control is enacted after a cumulative count of defective items is observed, thereby approximating the operator who allows a number of defective panels to accumulate before resetting the line. Analysis of this model found that the cost sensitivity to inspection error is dependent upon the level of control and that the level of control determines line utilisation. Additional analysis of this model demonstrated that additional inspection processes would lead to more stable cost structures but these structures many not necessarily be lower cost. The model was subsequently applied to investigate the economics of quality improvement. The quality problem of panel blemishes, induced by slivers (small metal fragments), was chosen as a case stuffy. Errors of 20-30% were observed during direct validation of the cost model and it was concluded that the use of discrete event simulation models for applications requiring high accuracy would not be possible unless the production system was of low complexity. However, the model could be used to evaluate the sensitivity of input factors and investigating the effects of a number of potential improvement opportunities. Therefore, the research concluded that it is possible to use discrete event simulation to determine the quality economics of an actual stamping plant. However, limitations imposed by inability of the model to consider a number of external factors, such as continuous improvement, operator working conditions or wear and the lack of reliable quality data, result in low cost accuracy. Despite this, it still can be demonstrated that discrete event simulation has significant benefits over the alternate modelling methods.

This paper presents an intelligent, hybrid system for stamping process planning in progressive die design. The system combines the flexibility of blackboard architecture with case-based reasoning. The hybrid system has the advantage that it can use past knowledge and experience for case-based reasoning when it exists, and other reasoning approaches when it doesn’t exist. A prototype system has been implemented in CLIPS and interfaced with Solid Edge CAD system. An example is included to demonstrate the approach. / Singapore-MIT Alliance (SMA)

In an automotive crash event, hot stamped, die quenched martensitic structural components have been shown to provide excellent intrusion resistance. These alloys exhibit only limited ductility, however, which may limit the overall impact performance of the component. The introduction of lower strength and more ductile “tailored” properties within some regions of a hot stamped component has the potential to improve impact performance. One approach being applied to achieving such tailored properties is through locally controlling the cooling rate within the stamping die. The primary motivation for the current work is to understand the role of cooling rate on the as-quenched mechanical response of tailored hot stampings, which has required characterization of the high strain rate mechanical behaviour of tailored hot stamped boron steel. The effect of cooling rate and resulting microstructure on the as-quenched mechanical behavior of USIBOR® 1500P boron steel at strain rates between 10-3 and 103 s-1 was investigated. Specimens quenched at rates above the critical cooling rate (~27 °C/s) exhibited a fully martensitic microstructure with a UTS of ~1,450 MPa. Sub-critical cooling rates, in the range 14°C/s to 50 °C/s, resulted in as-quenched microstructures ranging between bainitic to martensitic, respectively. Tension tests revealed that predominantly bainitic material conditions (14 °C/s cooling rate) exhibited a lower UTS of 816 MPa compared to 1,447 MPa for the fully martensitic material condition (50 °C/s cooling rate) with a corresponding increase in elongation from 0.10 to 0.15 for the bainitic condition. The reduction in area was 70% for the bainitic material condition and 58% for the martensitic material conditions which implied that a tailored region consisting of bainite may be a desirable candidate for implementation within a hot stamped component. The strain rate sensitivity was shown to be moderate for all of the as-quenched material conditions and the measured flow stress curves were used to develop a strain rate sensitive constitutive model, the “Tailored Crash Model (TCM)”. The TCM accurately reproduced the measured flow stress curves as a function of effective plastic strain, strain rate and Vickers hardness (or area fraction of martensite and bainite). The effect of deformation during quenching and the associated shift in the CCT diagram on the subsequent constitutive response was also examined for this material. Specimens were simultaneously quenched and deformed at various cooling rates to achieve a range of as-quenched microstructures that included ferrite in addition to martensite and bainite. Tensile tests conducted on these specimens at strain rates ranging from 0.003 s-1 to ~80 s-1 revealed that the presence of ferrite resulted in an increase in uniform elongation and n-value which increased overall energy absorption for a given hardness level. The strain rate sensitivity was shown to be moderate for all of the as-quenched material conditions and the TCM constitutive model was extended to account for the presence of ferrite. This extended constitutive model, the “Tailored Crash Model II (TCM II)”, has been shown to predict flow stress as a function of effective plastic strain, strain rate and area fraction of martensite, bainite and ferrite. As a validation exercise, uniaxial tension test simulations of specimens extracted from the transition zone of a hot stamped lab-scale B-pillar with tailored properties [1] were performed. The measured hardness distribution along the gauge length of the tensile specimens was used as input for the TCM constitutive model to define the element constitutive response used in the finite element (FE) models. The measured stress versus strain response and strain distribution during loading (measured using digital image correlation) was in excellent agreement with the FE models and thus validated the TCM constitutive model developed in this work. Validation of the TCM II version of the model is left for future work.

This research reports a simple and novel method to fabricate microlens arrays by soft stamping the unexposed SU-8 photoresist. A SU-8 based stamp composed of micro-nozzle arrays with a reservoir structure on a glass substrate is first fabricated using a process of dosage control exposure. The unexposed SU-8 is then encapsulated in the cross-linked SU-8 shell and was used as the ¡§ink¡¨ for the stamping process. The proposed SU-8 microlens array is then formed by stamping the formed SU-8 structure on a bare glass substrate at a temperature higher than the glass transition temperature (Tg) of the unexposed SU-8 microlens array. Lenses with various radii of curvature can be formed by controlling the working temperature during the stamping process. In addition, this work also employed a simple electric static pulling scheme to manipulate the fabricated lenses profiles. Aspherical SU-8 microlens arrays with a wide range of tunable focal lengths were fabricated with this approach. Furthermore, we develop an advanced localize E-field control technique to fabricate microlenses with various focus length and microlenses with different tilt angle in a single lens array sheet. A novel grayscale mask fabrication technique is also proposed first. This low cost and rapid method is applied on stepwise and continuous tilt plane fabrication for produces a gradually changed E-field. Hetero axes and focus lengths microlenses are fabricated with this approach. In order to farther understand the real E-field distribution, a novel PCF based E-field sensor fabrication technique is also proposed. This technique also shows the potential on various PCF based devices fabrications.

Abstract The conventional hydrophilic electrode used to spray the catalyst on the level-off carbon layer and the utilization of catalysts can only be reacted between the gas and the catalyst; however, the internal catalyst of the proton exchange membrane cannot be reacted. In order to increase the reaction of the catalyst, the hydrophobic pillared micro structures (HPMS) are made on the carbon layer, so that the gas can reach the catalyst in the internal membrane so that a reaction on large surface between the gas and the catalyst can be achieved. It is easier to build the gas channel in the internal HPMS than the structures of the carbon layer. As a result, more gas can be sent to the internal catalyst thus enlarging the reaction zone and more reactions between the gas and the catalyst is then achieved. The carbon powder is sprayed in the conventional HPMS in the deposition process. The HPMS are formed after the gravity process while the powder is passing the metal netmask and the manufacturing time is long. The experimental design uses electroforming to make the micro porous structure so that the hydrophobic carbon layer can be stamped thereby forming the HPMS. It has been proven that the time for the manufacturing process can be shortened if the micro structured metal template is applied. The micro structured metal template is used to stamp the small and large HPMS on the side electrode of the cathode, the stamping HPMS pressure was 500kg/cm2. With the same catalyst quantity the surface of the small HPMS was raised 63% and its performance was up to 55%; the surface of the large HPMS was raised 30% and its performance was up to 30%. The catalyst quantity of the cathode was reduced from 0.5mg/cm2 to 0.25 mg/cm2 and its performance remains the same. The experiment¡¦s results indicate that the reaction of the catalyst was only on the surface between the gas and the catalyst. Either small or large HPMS or after reducing the catalyst quantity can all raise the performance of the fuel cell as well as economize the catalyst. And by two kind of different size dimension microstructure metal template manufacture small or large HPMS, the electrode power density all may achieve 720mW/cm2 and 595mW/cm2.

When considering early Byzantine pilgrimage tokens, questions of touch and tactility arise almost instantly. Tokens lack cords or mountings, and so touch is implicit in such objects. Even gazing at them was a form of touching for the pilgrim. Hagiographies tell of pilgrims crowding to holy sites with the express intent to access sanctity through touch. Touch then, whether visual or manual, mediated the desire for connection between a pilgrim, a site, and a body. This requires an examination of a token’s touch as well as a pilgrim’s. In my thesis, I focus on a surviving token of the stylite saint Symeon the Younger, housed in the Menil Collection. This particular token bears iconography associated with physically and spiritually transformative events. Images of veneration, baptism, and healing appear together on the token’s obverse, while a human handprint on its reverse demands a multifaceted discussion of the implications of touching this object. I propose that in a pilgrim’s interaction with this token both object and viewer had agency. The token encapsulates a comprehensive pilgrimage experience. As a contact relic, the token makes present the saint’s body. Representation of baptism and the token’s backwards inscription enact sphragis – a figurative and literal stamping that pilgrims frequently described. I call attention to the experiential, memorial, and physical impressions made on the lives of early Byzantine pilgrims through the simultaneous touching of both viewer and object. / text

This thesis research focuses on fundamental understanding regarding the morphological transitions of weak polyelectrolyte multilayers (PEMs) formed by the layer-by-layer (LbL) electrostatic assembly of oppositely charged polymers. he first part of this thesis focuses on patterning polyelectrolyte multilayers that are able to undergo transitions from continuous films to porous materials by using hydrogel stamps. The stamping process is able to locally etch and pattern the porous transition in the LbL films by using reactive wet stamping (r-WETS). It was found that r-WETS of PEMs can also enable the modification of chemical functionality. The second part is an investigation about morphological changes of weak polyelectrolyte multilayers assembled with PAH and PAA using r-WETS in which hydrogel stamp material was soaked into various salt solutions and then applied to the LbL films. Also, in this study we presented a novel strategy to create a continuous gradient structure in thickness or porosity along the lateral direction of the thin films using concentration gradient salt stamping. The third part is an investigation regarding the mechanism of the transition from a continuous morphology to a porous morphology within weak polyelectrolyte multilayers. These morphological changes were able to be created by both acidic and basic post-assembly treatments, showing various morphological transitions from the introduction of porosity to the collapse of these porous structures and the eventual dissolution of the films. A similar observation of morphological transitions in weak polyelectrolyte multilayers was obtained by applying an electric field to the films in the fourth part of this thesis. Exposure to an electric field resulted in the creation of a porous structure, which can be ascribed to local changes in pH and subsequent structural rearrangements of the weak polyelectrolyte constituents. The final part of this thesis is to make PEMs into nanostructured matrices for inorganic synthesis. Multilayers possessing ion-exchangeable carboxylic acid groups were used for binding metal catalysts such as platinum (Pt) nanoparticles (NPs) within the film. Therefore, polyelectrolyte multilayers were able to stabilize catalytic Pt NPs in order to increase the useful time of catalyst materials suitable for use in proton exchange membrane fuel cells.