The subject of this diploma thesis is design and check of two steel structures. A production hall with a floor plan dimensions 24x50 m and an administrative building with floor plan dimensions 54x30 m. Both buildings are situated in Prostějov. The structure of the production hall has a roof pitched at 12%. The main frames have 6 m centre to centre spacing. The design of the production hall is processed in two options. The administrative building has 4 floors. The floor structures are made of composite steel and concrete structure. The structure is stabilized by vertical bracings in both directions. The computational model of both structures was built up using SCIA Engineer software.

The diploma thesis deals with the design and assessment of the steel construction of the car showroom in Jihlava. The ground dimensions of the structure are 40,0 x 52,0 m and the height at the highest point is 13,14 m. The supporting structure consists of a truss girder consisting of a set of arches, outer columns and an inner column with a strut. This is a freebase system, the distance of the bindings is 4.0 m. In the framework of the work is elaborated the comparison of two variants, more suitable includes the static calculation of the main supporting parts, including the joints and details. The main construction material is steel, grade S 355.

The diploma thesis deals with superstructure of apartment building in brno, which is located in a row house construction. The goal of the diploma thesis is to design new supporting structures and minimize the load from these construction because of low reservs in the load capacity of the existing supporting walls. the thesis contains a technical report, analysis of statics, drawing documentation and visualization. The internal forces were executed by software scia engineer.

Concretes reinforced by, using distributed steel reinforcements (fibres) are known as fibre-concrete. In case of disturbances or accidents of concrete structures reinforced with wires, it is necessary to carefully examine the actual implementation of dispersed reinforcement. Fibre concretes belong to modern building materials whose possible applications have not been fully utilized so far. Have been mainly used for floor structures loaded with factory halls and warehouses. Recently, thanks to well-known physical and mechanical properties of fibre-concrete, there were numerous attempts of designers, and namely investors, to utilize this kind of materials for support structures either. Favorable properties of wire-concrete can be utilized if there is a necessity to increase the resistance of concrete to stresses exceeding its strength, cyclic stress or impact stress. Daily practice shows to prove that the applications of fibre-concrete in such structures lead to the economic success. Necessary condition for successful application of steel fiber reinforced concrete in constructions however consists in its uniform dispersion, a homogeneous distribution of the wires throughout the volume of the structure. In case of inappropriate processing and deposition of the mixture during the manufacturing process fiber-concrete structures, the fibers are often unevenly distributed. Wires itself represent unfavourably shaped mixture components and they are extremely deteriorating its workability. A grouping of wires may be encountered as well, which reduces the overall homogeneity and the quality of steel fiber-concrete structures. If the homogeneity of fibre-concrete is not kept, the material possess different properties in various parts of the structure (for example, tensile strength), which can lead to defects in the structure (generation and development of cracks). The relevant lower reliability of the structure which is caused by unequal distribution of fibres (wires) in concrete volume can lead to damage of the property as well as the safety and the human lives can be jeopardized. Hence it is necessary to secure the effective control of the fibre-concrete homogeneity in ready support fibre-concrete structures. Contemporary homogeneity control is still ongoing on fresh blends, but if the fibre-concrete hardened and is a part of the construction, no known reliable methods are currently in available to test the homogeneity of the fibre-concrete on the structure without its destruction. The methods developed to control the concentration of wires in wire-concrete structures are based mostly on magnetic or electromagnetic properties of wires. The thesis deals with the development of the magnetic method in situ using permanent magnets for monitoring the distribution of fibers in hardened steel fiber-concrete structures. The test principle is based on measurements of the changes in magnetic field strength of permanent magnets which are induced by a change in wire distribution in steel fibre-concrete structure. Test is characterized as a so called local- failure- test using a small diameter core drill. In this sense it is a semi-destructive method.

Master's thesis addresses the design and assessment of the load bearing structure of the shopping gallery. The building is designed as a three-storey rectangular plan with a flat roof. The structure is composed of steel frames and composite steel and concrete slabs. There are proposed two possible solutions - variant with a flat roof and direct central gallery, a reinforced rigid steel frames and a variant with a cupola roofed circular inner atrium, solidified with rods.

The aim of this master's thesis is to design the steel construction of a multifunctional building in the cadastral area of Brno-Bohunice. Multifunctional building consists of two identical buildings - A and B. Floor plan dimensions are 40.0 x 40.0 meters and height of 33,8 meters. Both objects have the 1st floor of the overall height of 5,0 m, each additional floors 3,5 m. The plan shape of the building is a square 40 x 40 m with bevel in the corners with a length of 8 m. In the middle of the building is roofed atrium 8 x 8 m. The buildings are in the 5th floor connected with the enclosed footbridge with a length of 10.0 meters. The main structure consists of two buildings columns and girders. Columns are alternatively solved as the composite steel and concrete structures with closed section filled with concrete or concreted steel profile. The girders are made of castellated beams. Among the girders are embedded solid panel joists and girders, coupled with the composite steel and concrete slab. Spatial rigidity besides the composite slabs provide rods placed around the atrium and in the corners of the building. The main structure of the footbridge consists of two inclined arched beams on which is placed stringer of the footbridge.

The diploma work deals with a design of a steel load-bearing structure for a multi-storey building with an atrium consisting of five above ground floors. The property is situated into Blansko area. Its ground-plan measures are 32.5 x 56 m. The maximum height of the property is 23.2 m. The height of the floor is 4 m. Load-bearing structure is designed with articulated joints. The atrium roof is formed from truss girders. The design and assessment is done according to rules in operation.

According to the 2019 Canadian infrastructure report card, a concerning amount of municipal infrastructure is in poor or very poor condition. The infrastructure in this condition requires immediate action for rehabilitation or replacement. For concrete infrastructure, an effective repair can extend its service life and ensure that the services it provides continue to meet the community expectations. However, unfavorable environmental factors such as repeated/cyclic loads and freezing and thawing cycles adversely affect the bond between substrate concrete and repair materials, which lowers the structural capacity of repaired structures. So far, researchers have found that bond strength of repair can be affected by surface roughness, surface moisture, chemical adhesion or cohesion, curing regime, properties of substrate and repair materials, use of bond agent, and curing regimes. These findings are mostly based on the studies that focused on cold-jointed cylinders or beams, but in real-life repair situations, repairs of beams or slabs are located at either tension or compression side of the structure. Currently, there is no comprehensive study that investigates the bond of concrete repair under a combination of freezing and thawing and repeated/cyclic loading conditions. In addition, it is challenging to provide a rapid and non-destructive evaluation of the bond deterioration of repair materials. To address these issues systematically, this dissertation breaks the task into four phases. Phase (I) focuses on the development of an engineered “crack-free” repair mix that contains polypropylene (PP) fiber. A novel method is used to surface treat the PP fibers with supplementary cementitious materials. The effectiveness of surface-treating fibers for improved bond strength and reduced cracking is investigated. The compressive, tensile, and flexural strength of this engineered repair mix are determined and compared with two commercially available repair materials. The results from Phase I show that by adding 0.2% (by weight) Metakaolin-treated fibers into concrete mix, the compressive strength improves by up to 15.7% compared to mixes with untreated fibers. This study achieved a strength increase of 13.5% as compared to the reported 3.3% in other studies that use 25 times the amount of metakaolin used in this study. The experimental results confirm that at 0.2% dosage level, the use of novel surface treating technique is a cost-effective way to improve the strength of repair materials. Phase (II) focuses on characterizing the bond strength of various repair systems after freezing-thawing (FT) damage using both non-destructive and destructive methods. Two innovative sounding methods, which overcome the subjectivity of the traditional chain drag method, are used to evaluate FT damage non-destructively. In the experimental study, beams with a U-shaped cut are made to simulate conditions experienced by a concrete structure during a typical repair project. Three types of repair materials are used including cementitious repair concrete, cementitious repair mortar, and polymer-modified cementitious mortar. After up to 300 cycles of freeze-thaw exposure, resonant frequency and bond flexural strength of the prismatic specimens are determined. The empirical equations relating Non-destructive test (NDT) measurements and flexural bond strength of the repaired structures after freeze-thaw (FT) exposure are proposed. The results from Phase II show that the change in dynamic modulus of elasticity determined from NDTs agrees well with the change in other measurements including flexural bond strength, interfacial crack width, and mass loss after freeze-thaw exposure. In this study, linear relationships are established between dynamic modulus of elasticity and flexural bond strength for both cementitious and polymer-modified cementitious repair mortar with a coefficient of determination ranging between 0.87 and 0.95. The proposed empirical models can be used to predict bond flexural strength of repaired structures based on NDT measurement. Also, it was found that the samples repaired with polymer-modified cementitious mortar (Mix P) have superior FT resistance compared to other repaired samples. Phase (III) focuses on investigating the structural capacity and bond performance of repaired beams after cyclic/repeated loading. To accelerate the test process, a novel modified loading regime consisting of cycle groups of increasing cyclic/repeated stress amplitude is proposed. The models proposed by literature and current codes and standards are used to validate the results. Phase (IV) focuses on the development of the damage models for both individual and combined FT and cyclic loading exposure on repaired concrete structures. The results in phase III show the feasibility of using the Palmgren-Miner rule and Goodman linear model to estimate the fatigue life of repaired structures. This was confirmed within the context of this study. This study established the usefulness of using groups of increasing cyclic stress amplitude to accelerate the fatigue test process. The two-million cycle fatigue endurance limit estimated using cycle groups of Mix S (70.8%) was very similar to what was reported in the literature (71%) using the traditional time-consuming cyclic loading method. This study found that the formulas proposed by CSA 23.3 can effectively predict the moment resistance of both intact (control) and repaired RC beams. The ratio of experimental moment resistance values to its predictions ranges from 0.91 to 1.04. Based on the experimental results of previous three phases, an empirical model that predicted the fatigue service life of FT-damaged concrete structures is proposed. Future research requires a more comprehensive study on the FT performance of various polymer-modified cementitious mortars of different mix designs in repairing concrete structures. By increasing the number of tested specimens, a better relationship could be established between destructive and NDT methods. Future research is also required to explore the combined effect of FT and cyclic loading on repaired RC structures experimentally. / Graduate / 2023-03-22

Tragwerke aus Stahlbeton weisen infolge des Kriechens und Schwindens des Betons ein zeitveränderliches Materialverhalten auf. Die Folge sind Umlagerungen der im Querschnittsinneren wirkende Kräfte und im Zeitverlauf zunehmende Verformungen. Zur Beurteilung dieses Langzeitverhaltens sind geeignete Berechnungsmodelle erforderlich, die im Planungsstadium eine zuverlässige Prognose ermöglichen. Dabei spielen nicht nur reine Stahlbetonkonstruktionen eine Rolle, sondern im Zuge von Ertüchtigungsmaßnahmen werden zur Erhöhung der Tragfähigkeit zunehmend auch textile Bewehrungen aus Carbon- und AR-Glasfasern eingesetzt. Durch die beanspruchungsgerecht aufzubringenden Bewehrungsstrukturen und einen speziellen Feinbeton können sehr geringe Betonschichtdicken realisiert werden. Es entsteht ein Verbundquerschnitt mit unterschiedlichen Betonrezepturen, gleichfalls unterschiedlichem Betonalter und mit mehreren verschiedenen Bewehrungskomponenten. Um Aussagen zum Langzeitverhalten derartiger Konstruktionen treffen zu können, ist eine ganzheitliche Betrachtung über alle diese im Verbund liegenden Komponenten mit ihren jeweiligen Materialeigenschaften erforderlich. Im Rahmen der vorliegenden Arbeit sind in einem ersten Schritt die Stoffgesetze für die beteiligten Materialien Beton, Stahl- und Textilfaserbewehrung zu formulieren. Im Mittelpunkt steht dabei das viskoelastische Verhalten des Betons, für dessen baumechanische Beschreibung ein geeignetes rheologisches Modell in Form einer Feder-Dämpfer-Kombination dargestellt und die zugehörige Spannungs-Dehnungs-Zeit-Beziehung hergeleitet wird. Ferner wird aufgezeigt, wie die erforderlichen Materialparameter mit Hilfe üblicher Berechnungsansätze für Kriechen und Schwinden (z.B. nach EUROCODE 2) kalibriert werden können. Die betrachteten Textilfasern werden zunächst mit linear-elastischem Verhalten in Rechnung gestellt. Auf alternative Ansätze, die auch hier viskoelastische Eigenschaften berücksichtigen, wird hingewiesen, und das Berechnungsmodell ist dahingehend erweiterbar gestaltet. In einem zweiten Schritt werden die Materialmodelle der Einzelkomponenten nach den mechanischen Grundprinzipien von Gleichgewicht und Verträglichkeit und unter der BERNOULLIschen Annahme eines eben bleibenden Querschnittes miteinander in Beziehung gesetzt. Hierfür ist eine inkrementelle Vorgehensweise erforderlich, die mit dem Zeitpunkt der ersten Lastaufbringung beginnt und schrittweise den darauffolgenden Zustand berechnet. Im Ergebnis entsteht ein Algorithmus, der die am Querschnitt stattfindenden Veränderungen im Spannungs- und Dehnungsverhalten unter Einbeziehung der Stahlbewehrung sowie einer ggf. vorhandenen Textilbetonschicht wirklichkeitsnah erfaßt. Für statisch bestimmte Systeme mit bekanntem Schnittkraftverlauf wird gezeigt, wie sich so zu jeder Zeit an jeder Stelle der vorliegende Dehnungszustand und aus diesem über die Krümmung die Durchbiegung berechnen läßt. Der dritte und für viele praktische Anwendungen wichtigste Schritt besteht darin, die am Querschnitt hergeleiteten Beziehungen in ein finites Balkenelement zu überführen und dieses in ein FE-Programm zu implementieren. Auch das gelingt auf inkrementellem Wege, wobei für jedes Zeitinkrement die Spannungs- und Verformungszuwächse aller Elemente mit Hilfe des NEWTON-RAPHSON-Verfahrens über die Iteration des Gleichgewichtszustandes am gesamten System bestimmt werden. Hierzu werden einige Beispiele vorgestellt, und es werden die Auswirkungen des Kriechens und Schwindens mit den sich daraus ergebenden Folgen für das jeweilige Tragwerk erläutert. Ferner wird gezeigt, wie textilbewehrte Verstärkungsmaßnahmen gezielt eingesetzt werden können, um das Trag- und Verformungsverhalten bestehender Bauwerke unter Beachtung des zeitveränderlichen Materialverhaltens kontrolliert und bedarfsgerecht zu beeinflussen. / Structures of reinforced concrete show a time-varying material behaviour due to creeping and shrinking of the concrete. This results in the rearrangement of the stresses in the cross-section and time-depending increase of the deformations. Qualified calculation models enabling a reliable prediction during the design process are necessary for the assessment of the long-term behavior. Not only pure reinforced concrete structures play an important role, but within retrofitting actions textile reinforcements of carbon and AR-glass fibres are applied in order to enhance the load-bearing capacity. A small concrete-layer-thickness can be achieved by the load-compatible application of reinforced textile configurations and the usage of a special certain fine-grained concrete. It leads to a composite section of different concrete recipes, different concrete ages and also several components of reinforcement. To give statements for the long-term behaviour of such constructions, a holistic examination considering all this influencing modules with their particular material properties is necessary. Within this dissertation in a first step the material laws of the participated components, as concrete, steel and textile reinforcement, are defined. The focus is layed on the visco-elastic behaviour of the concrete. For its mechanical specification a reliable rheological model in terms of a spring-dashpot-combination is developed and the appropriate stress-strain-time-relation is derived. Furthermore the calibration of the required material parameters considering creep and shrinkage by means of common calculation approaches (e.g. EUROCODE 2) is demonstrated. For the textile fibres a linear-elastic behaviour is assumed within the calculation model. It is also refered to alternative approaches considering a visco-elastic characteristic and the calculation model is configured extendable to that effect. In a second step the material models of the single components are correlated taking into account the mechanical basic principles of equilibrium and compatibility as well as the BERNOULLIan theorem of the plane cross-section. Therefore an incremental calculation procedure is required, which starts at the moment of the first load-application and calculates the subsequent configuration step by step. In the result an algorithm is derived, that realistically captures the occuring changings of stress and strain in the cross-section by considering the steel reinforcement as well as a possibly existing layer of textile concrete. For statically determined systems with known section force status it is demonstrated how to calculate the existing condition of strain and following the deflection via the curvaturve at every time and at each position. The third step - for many practical applications the most important one - is the transformation of the derived relations at the cross-section into a finite beam-element and the implementation of this in a FE-routine. This also takes place in an incremental way, whereat for each time-increment the increase of stress and strain for all elements is identified by using the NEWTON-RAPHSON-method within the iteration process for the equilibrium condition of the whole system. Meaningful numerical examples are presented and the effects of creep and shrinkage are explained by depicting the consequences for the particular bearing structure. Moreover it is shown how the purposeful use of textile reinforcement strengthening methodes can influence and enhance the load-bearing and deflection characteristics of existing building constructions by considering the time-varying material behaviour.

This diploma thesis deals with design of steel structure with composite steel-concrete floor structure of a office building.The building is located in Moravský Krumlov. The Office buidling consist of multi-storey building and an entrance atrium. The total ground plan's dimensions are 52,8m x 48,0m. The multi-storey building has 8 floor. The maximum heigh of the building is 25,32m above ground. The project is designed in two options. For winning variant is including check and it is performed a drawings with design and check assembly details and anchorage.