Synthetic vascular grafts are useful to bypass diseased arteries. The long-term failure of synthetic grafts is primarily due to intimal hyperplasia at the anastomotic sites. The accelerated intimal hyperplasia may stem from a compliance mismatch between the host artery and the graft since commercially available synthetic conduits are much stiffer than an artery. The objective of this thesis is to design a method for fabricating a vascular graft that mechanically matches the patients native artery over the expected physiologic range of pressures. The creation of an optimized mechanical graft will hopefully lead to an improvement in patency rates. The mechanical equivalency between the graft and the host artery is defined locally by several criteria including the diameter upon inflation, the elasticity at mean pressure, and axial force. A single parameter mathematical for a thin-walled tube is used to describe of the final mechanical behavior of a synthetic graft. For the general problem, the objective would be to fabricate a mechanics-matching vascular graft for each host artery. Typically, fabrication parameters are set initially and the properties of the fabricated graft are measured. However, by modeling the entire fabrication process and final mechanical properties, it is possible to invert the situation and let the typical output mechanical values be used to define the fabrication parameters. The resultant fabricated graft will then be mechanically matching. As a proof-of-concept, several prototype synthetic grafts were manufactured and characterized by a single Invariant to match a canine artery. The resultant graft equaled the diameter upon inflation, the elasticity at mean pressure, and axial force of the native canine artery within 6%. An alternative to making an individual graft for each artery is also presented. A surgeon may choose the best graft from a set of pre-manufactured grafts, using a computer program algorithm for best fit using two parameters in a neighborhood. The design optimization problem was solved for both canine carotid and human coronary arteries. In conclusion, the overall process of design, fabrication and selection of a mechanics matching synthetic vascular graft is shown to be reliable and robust.

Part 1: Theoretic background information - Review of Hooke’s law for linear elastic materials - The strain energy density of linear elastic materials - Hyperelastic material - Material laws for hyperelastic materials - About selecting the material model and performing tests - Implementation of hyperelastic material laws in Mechanica - Defining hyperelastic material parameters in Mechanica - Test set-ups and specimen shapes of the supported material tests - The uniaxial compression test - Stress and strain definitions in the Mechanica LDA analysis Part 2: Application examples - A test specimen subjected to uniaxial loading - A volumetric compression test - A planar test - Influence of the material law Appendix - PTC Simulation Services Introduction - Dictionary Technical English-German / Teil 1: Theoretische Hintergrundinformation - Das Hookesche Gesetz für linear-elastische Werkstoffe - Die Dehnungsenergiedichte für linear-elastische Materialien - Hyperelastisches Material - Materialgesetze für Hyperelastizität - Auswählen des Materialgesetzes und Testdurchführung - Implementierung der hyperelastischen Materialgesetze in Mechanica - Definieren der hyperelastischen Materialparameter in Mechanica - Testaufbauten und Prüfkörper der unterstützten Materialtests - Der einachsige Druckversuch - Spannungs- und Dehnungsdefinition in der Mechanica-Analyse mit großen Verformungen Teil 2: Anwendungsbeispiele - Ein einachsig beanspruchter Prüfkörper - Ein volumetrischer Drucktest - Ein planarer Test - Einfluss des Materialgesetzes Anhang: - Kurzvorstellung der PTC Simulationsdienstleistungen - Wörterbuch technisches Englisch-Deutsch

Part 1: Theoretic background information - Review of Hooke’s law for linear elastic materials - The strain energy density of linear elastic materials - Hyperelastic material - Material laws for hyperelastic materials - About selecting the material model and performing tests - Implementation of hyperelastic material laws in Mechanica - Defining hyperelastic material parameters in Mechanica - Test set-ups and specimen shapes of the supported material tests - The uniaxial compression test - Stress and strain definitions in the Mechanica LDA analysis Part 2: Application examples - A test specimen subjected to uniaxial loading - A volumetric compression test - A planar test - Influence of the material law Appendix - PTC Simulation Services Introduction - Dictionary Technical English-German / Teil 1: Theoretische Hintergrundinformation - Das Hookesche Gesetz für linear-elastische Werkstoffe - Die Dehnungsenergiedichte für linear-elastische Materialien - Hyperelastisches Material - Materialgesetze für Hyperelastizität - Auswählen des Materialgesetzes und Testdurchführung - Implementierung der hyperelastischen Materialgesetze in Mechanica - Definieren der hyperelastischen Materialparameter in Mechanica - Testaufbauten und Prüfkörper der unterstützten Materialtests - Der einachsige Druckversuch - Spannungs- und Dehnungsdefinition in der Mechanica-Analyse mit großen Verformungen Teil 2: Anwendungsbeispiele - Ein einachsig beanspruchter Prüfkörper - Ein volumetrischer Drucktest - Ein planarer Test - Einfluss des Materialgesetzes Anhang: - Kurzvorstellung der PTC Simulationsdienstleistungen - Wörterbuch technisches Englisch-Deutsch

No description available.

Calcific aortic valve disease (CAVD) is one of the most common causes of cardiovascular disease in North America. Mechanical factors have been closely linked to the pathogenesis of CAVD and may contribute to the disease by actively regulating the mechanobiology of valve interstitial cells (VICs). Mechanical forces affect VIC function through interactions between the VIC and the extracellular matrix (ECM). Studies have shown that the transfer of mechanical stimulus during cell-ECM interaction depends on the local material properties at hierarchical length scales encompassing tissue, cell and cytoskeleton. In this thesis, biomechanical tools were developed and applied to investigate hierarchical cell-ECM interactions, using VICs and valve tissue as a model system. Four topics of critical importance to understanding VIC-ECM interactions were studied: focal biomechanical material properties of aortic valve tissue; viscoelastic properties of VICs; transduction of mechanical deformation from the ECM to the cytoskeletal network; and the impact of altered cell-ECM interactions on VIC survival. To measure focal valve tissue properties, a micropipette aspiration (MA) method was implemented and validated. It was found that nonlinear elastic properties of the top layer of a multilayered biomaterial can be estimated by MA by using a pipette with a diameter smaller than the top layer thickness. Using this approach, it was shown that the effective stiffness of the fibrosa layer is greater than that of the ventricularis layer in intact aortic valve leaflets (p<0.01). To characterize the viscoelastic properties of VICs, an inverse FE method of single cell MA was developed and compared with the analytical half-space model. It was found that inherent differences in the half-space and FE models of single cell MA yield different cell viscoelastic material parameters. However, under particular experimental conditions, the parameters estimated by the half-space model are statistically indistinguishable from those predicted by the FE model. To study strain transduction from the ECM to cytoskeleton, an improved texture correlation algorithm and a uniaxial tension release device were developed. It was found that substrate strain fully transfers to the cytoskeletal network via focal adhesions in live VICs under large strain tension release. To study the effects of cell-ECM interactions on VIC survival, two mechanical stimulus systems that can simulate the separate effects of cell contraction and cell monolayer detachment were developed. It was found that cell sheet detachment and disrupted cell-ECM signaling is likely responsible for the apoptosis of VICs grown in culture on thin collagen matrices, leading to calcification. The studies presented in this thesis refine existing biomechanical tools and provide new experimental and analytical tools with which to study cell-ECM interactions. Their application resulted in an improved understanding of hierarchical valve biomechanics, mechanotransduction, and mechanobiology.

Calcific aortic valve disease (CAVD) is one of the most common causes of cardiovascular disease in North America. Mechanical factors have been closely linked to the pathogenesis of CAVD and may contribute to the disease by actively regulating the mechanobiology of valve interstitial cells (VICs). Mechanical forces affect VIC function through interactions between the VIC and the extracellular matrix (ECM). Studies have shown that the transfer of mechanical stimulus during cell-ECM interaction depends on the local material properties at hierarchical length scales encompassing tissue, cell and cytoskeleton. In this thesis, biomechanical tools were developed and applied to investigate hierarchical cell-ECM interactions, using VICs and valve tissue as a model system. Four topics of critical importance to understanding VIC-ECM interactions were studied: focal biomechanical material properties of aortic valve tissue; viscoelastic properties of VICs; transduction of mechanical deformation from the ECM to the cytoskeletal network; and the impact of altered cell-ECM interactions on VIC survival. To measure focal valve tissue properties, a micropipette aspiration (MA) method was implemented and validated. It was found that nonlinear elastic properties of the top layer of a multilayered biomaterial can be estimated by MA by using a pipette with a diameter smaller than the top layer thickness. Using this approach, it was shown that the effective stiffness of the fibrosa layer is greater than that of the ventricularis layer in intact aortic valve leaflets (p<0.01). To characterize the viscoelastic properties of VICs, an inverse FE method of single cell MA was developed and compared with the analytical half-space model. It was found that inherent differences in the half-space and FE models of single cell MA yield different cell viscoelastic material parameters. However, under particular experimental conditions, the parameters estimated by the half-space model are statistically indistinguishable from those predicted by the FE model. To study strain transduction from the ECM to cytoskeleton, an improved texture correlation algorithm and a uniaxial tension release device were developed. It was found that substrate strain fully transfers to the cytoskeletal network via focal adhesions in live VICs under large strain tension release. To study the effects of cell-ECM interactions on VIC survival, two mechanical stimulus systems that can simulate the separate effects of cell contraction and cell monolayer detachment were developed. It was found that cell sheet detachment and disrupted cell-ECM signaling is likely responsible for the apoptosis of VICs grown in culture on thin collagen matrices, leading to calcification. The studies presented in this thesis refine existing biomechanical tools and provide new experimental and analytical tools with which to study cell-ECM interactions. Their application resulted in an improved understanding of hierarchical valve biomechanics, mechanotransduction, and mechanobiology.

This diploma thesis deals with the different possible calculations of crack path. Specifically, it focuses on criteria based on maximum tangential stress, minimal strain energy density, crack tip displacement, and local symmetry. These criteria are used for calculations in ANSYS software to estimate possible crack paths on four simple structures. The thesis also contains the codes created in ANSYS. Using these, the crack trajectory of a given structure can be calculated by any of the four criteria described.

Part 1: Theoretic background information - Review of Hooke’s law for linear elastic materials - The strain energy density of linear elastic materials - Hyperelastic material - Material laws for hyperelastic materials - About selecting the material model and performing tests - Implementation of hyperelastic material laws in Mechanica - Defining hyperelastic material parameters in Mechanica - Test set-ups and specimen shapes of the supported material tests - The uniaxial compression test - Stress and strain definitions in the Mechanica LDA analysis Part 2: Application examples - A test specimen subjected to uniaxial loading - A volumetric compression test - A planar test - Influence of the material law Appendix - PTC Simulation Services Introduction - Dictionary Technical English-German / Teil 1: Theoretische Hintergrundinformation - Das Hookesche Gesetz für linear-elastische Werkstoffe - Die Dehnungsenergiedichte für linear-elastische Materialien - Hyperelastisches Material - Materialgesetze für Hyperelastizität - Auswählen des Materialgesetzes und Testdurchführung - Implementierung der hyperelastischen Materialgesetze in Mechanica - Definieren der hyperelastischen Materialparameter in Mechanica - Testaufbauten und Prüfkörper der unterstützten Materialtests - Der einachsige Druckversuch - Spannungs- und Dehnungsdefinition in der Mechanica-Analyse mit großen Verformungen Teil 2: Anwendungsbeispiele - Ein einachsig beanspruchter Prüfkörper - Ein volumetrischer Drucktest - Ein planarer Test - Einfluss des Materialgesetzes Anhang: - Kurzvorstellung der PTC Simulationsdienstleistungen - Wörterbuch technisches Englisch-Deutsch

Part 1: Theoretic background information - Review of Hooke’s law for linear elastic materials - The strain energy density of linear elastic materials - Hyperelastic material - Material laws for hyperelastic materials - About selecting the material model and performing tests - Implementation of hyperelastic material laws in Mechanica - Defining hyperelastic material parameters in Mechanica - Test set-ups and specimen shapes of the supported material tests - The uniaxial compression test - Stress and strain definitions in the Mechanica LDA analysis Part 2: Application examples - A test specimen subjected to uniaxial loading - A volumetric compression test - A planar test - Influence of the material law Appendix - PTC Simulation Services Introduction - Dictionary Technical English-German / Teil 1: Theoretische Hintergrundinformation - Das Hookesche Gesetz für linear-elastische Werkstoffe - Die Dehnungsenergiedichte für linear-elastische Materialien - Hyperelastisches Material - Materialgesetze für Hyperelastizität - Auswählen des Materialgesetzes und Testdurchführung - Implementierung der hyperelastischen Materialgesetze in Mechanica - Definieren der hyperelastischen Materialparameter in Mechanica - Testaufbauten und Prüfkörper der unterstützten Materialtests - Der einachsige Druckversuch - Spannungs- und Dehnungsdefinition in der Mechanica-Analyse mit großen Verformungen Teil 2: Anwendungsbeispiele - Ein einachsig beanspruchter Prüfkörper - Ein volumetrischer Drucktest - Ein planarer Test - Einfluss des Materialgesetzes Anhang: - Kurzvorstellung der PTC Simulationsdienstleistungen - Wörterbuch technisches Englisch-Deutsch

The desire for energy and resource savings brings magnesium alloys as lightweight materials with high specific strength more and more into the focus. Most structural components are subjected to cyclic loading. In the course of computer aided product development, a numerical prediction of the fatigue life under these conditions must be provided. For this reason, the mechanical properties of the considered material must be examined in detail. Wrought magnesium semifinished products, e.g. magnesium sheet metals, typically reveal strong basal textures and thus, the mechanical behavior considerably differs from that of the well-established magnesium die castings. Magnesium sheet metals reveal a distinct difference in the tensile and compressive yield stress, leading to non-symmetric sigmoidal hysteresis loops within the elasto-plastic load range. These unusual hysteresis shapes are caused by cyclic twinning and detwinning. Furthermore, wrought magnesium alloys reveal pseudoelastic behavior, leading to nonlinear unloading curves. Another interesting effect is the formation of local twin bands during compressive loading. Nevertheless, only little information can be found on the numerical fatigue analysis of wrought magnesium alloys up to now. The aim of this thesis is the investigation of the mechanical properties of wrought magnesium alloys and the development of an appropriate fatigue model. For this purpose, twin roll cast AM50 as well as AZ31B sheet metals and extruded ME21 sheet metals were used. Mechanical tests were carried out to present a comprehensive overview of the quasi-static and cyclic material behavior. The microstructure was captured on sheet metals before and after loading to evaluate the correlation between the microstructure, the texture, and the mechanical properties. Stress- and strain-controlled loading ratios and strain-controlled experiments with variable amplitudes were performed. Tests were carried out along and transverse to the manufacturing direction to consider the influence of the anisotropy. Special focus was given to sigmoidal hysteresis loops and their influence on the fatigue life. A detailed numerical description of hysteresis loops is necessary for numerical fatigue analyses. For this, a one-dimensional phenomenological model was developed for elasto-plastic strain-controlled constant and variable amplitude loading. This model consists of a three-component equation, which considers elastic, plastic, and pseudoelastic strain components. Considering different magnesium alloys, good correlation is reached between numerically and experimentally determined hysteresis loops by means of different constant and variable amplitude load-time functions. For a numerical fatigue life analysis, an energy based fatigue parameter has been developed. It is denoted by “combined strain energy density per cycle” and consists of a summation of the plastic strain energy density per cycle and the 25 % weighted tensile elastic strain energy density per cycle. The weighting represents the material specific mean stress sensitivity. Applying the energy based fatigue parameter on modeled hysteresis loops, the fatigue life is predicted adequately for constant and variable amplitude loading including mean strain and mean stress effects. The combined strain energy density per cycle achieves significantly better results in comparison to conventional fatigue models such as the Smith-Watson-Topper model. The developed phenomenological model in combination with the combined strain energy density per cycle is able to carry out numerical fatigue life analyses on magnesium sheet metals.