Les matériaux composites à matrice organique sont largement utilisés dans l'industrie des transports et notamment dans le domaine aéronautique. Pour permettre un dimensionnement optimal des structures, il est nécessaire d'étudier le comportement des matériaux CMO sur une large gamme de vitesses et de températures.L'objectif de cette thèse est de proposer un modèle de comportement et de rupture permettant de prédire la réponse des CMO sur une large gamme de vitesses de sollicitation et de températures. Les recherches se sont intéressées dans un premier temps à la caractérisation de la transition entre les régimes de comportement linéaire et non linéaire du matériau unidirectionnel T700GC/M21 (renforts de fibres de carbone, résine époxy), ainsi qu'à la dépendance de cette transition à la vitesse de sollicitation et à la température. Les travaux se sont ensuite focalisés sur l'étude expérimentale du régime de comportement non linéaire endommageable du T700GC/M21. Enfin, au terme de ces deux étapes, une version améliorée du modèle disponible à l'ONERA pour les composites stratifiés (OPFM) a été proposée, version intégrant un critère de transition linéaire/non linéaire de comportement, et une prise en compte de l'influence de la vitesse de sollicitation et de la température sur la réponse du matériau / Nowadays, organic matrix composite materials are widely used in the transportation industry, and particularly in the aeronautical industry. To provide an optimal dimensioning of the structures, it is necessary to study the mechanical behavior of OMC on a large range of strain rates and temperatures. The aim of this PhD thesis is to propose a behavior and a rupture model to predict the mechanical response of OMC for a large range of strain rates and temperatures. The research was initially focused on the characterization of the transition between the linear and nonlinear behavior of the material T700GC/M21, a carbon / epoxy unidirectional laminate as well as the strain rate and temperature dependencies of this transition. The work was then focused on the experimental study of the nonlinear damaged behavior of the T700GC/M21. Finally, completing these first two steps, an updated version of the behavior model available at ONERA (OPFM) was proposed which includes the transition between linear and nonlinear behavior and the influence of strain rate and temperature on the mechanical response of the material.

This investigation is focused on the understanding of mechanical and chemical reaction behaviors of stoichiometric mixtures of nano- and micro-scale aluminum and hematite (Fe2O3) powders dispersed in epoxy. Epoxy-cast Al+Fe2O3 thermite composites are an example of a structural energetic material that can simultaneously release energy while providing structural strength. The structural and energetic response of this material system is investigated by characterizing the mechanical behavior under high-strain rate and shock loading conditions. The mechanical response and reaction behavior are closely interlinked through deformation characteristics. It is, therefore, desirable to understand the deformation behavior up to and beyond failure and establish the necessary stress and strain states required for initiating chemical reactions. The composite s behavior has been altered by changing two main processing parameters; the reactants particle size and the relative volume fraction of the epoxy matrix. This study also establishes processing techniques necessary for incorporating nanometric-scale reactants into energetic material systems. The mechanochemical behavior of epoxy-cast Al+Fe2O3 composites and the influence of epoxy volume fraction have been evaluated for a variety of loading conditions over a broad range of strain rates, which include low-strain rate or quasistatic loading experiments (10-4 to 10-2 1/s), medium-strain rate Charpy and Taylor impacts (103 to 104 1/s), and high-strain rate parallel-plate impacts (105 to 106 1/s). In general, structural strength and toughness have been observed to improve as the volume fraction of epoxy decreases, regardless of the loading strain rate regime explored. Hugoniot experiments show damage occurring at approximately the same critical impact stress for compositions prepared with significantly different volume fractions of the epoxy binder phase. Additionally, Taylor impact experiments have indicated evidence for strain-induced chemical reactions, which subject the composite to large shear accompanied by temperature increase and associated softening, preceding these reactions. Overall, the work aims to establish an understanding of the microstructural influence on mechanical behavior and chemical reactivity exhibited by epoxy-cast Al+Fe2O3 materials when exposed to high stress and high-strain loading conditions. The understanding of fundamental aspects and the results of impact experiment measurements provide information needed for the design of structural energetic materials.

The linear instability of laterally diverging/converging flows is an important aspect towards understanding the laminar-transition process in many viscous flows. In this work the linear instability of constant pressure laterally diverging/converging flow has been investigated. The laminar velocity field for laterally diverging/converging flows, under the source/sink approximation, has been reduced to two-dimensional flows. This reduction is alternative to the Mangier transformation used earlier. For a constant pressure laterally strained flow, the laminar velocity is found to be governed by the Blasius equation for flow over a flat plate. The non-parallel linear instability of constant pressure laterally strained flows has been examined. The instability equation is found to be same as that for the Blasius flow. This implies that the stability is same as that for the Blasius flow. A lateral divergence/convergence is shown to alter the Reynolds number from that in a two-dimensional flow. The instability of a laterally converging/diverging flow thus can be obtained from the available results for the Blasius flow by scaling the Reynolds numbers. This leads to the result that while a diverging flow is more unstable than the Blasius flow, a converging flow is more stable. Some additional relevant results are also presented.

Rate-dependent effects introduced during rapid and/or dynamic events have typically been oversimplified to compensate for deficiencies in present analyses. As load test results are generally considered as the basis of performance from which foundations can be designed, it is imperative that the analyzed load test data be as accurate as possible. In an attempt to progress the state of load test data regression, this dissertation addresses two common assumptions made during the regression process: (1) the statnamic damping coefficient is constant throughout the entire load test and (2) the concrete stress-strain relationship is linear-elastic. Also presented is a case study where the inherent features of a rapid load test proved useful in identifying the occurrence and proximity of a structural failure within a drilled shaft.

Deliberate and accidental explosions along with the heightened risk of loss of life and property damage during such events have highlighted the need for research in the behaviour of materials under high strain rates. Where an extensive body of research is available on steel and concrete structures, little to no details on how to address the design or retrofitting of wood structures subjected to a blast threat are available. Studies reported in the literature that focused on full scale light-frame wood structures did not quantify the increase in capacity due to the dynamic loading while the studies that did quantify the increase mostly stems from small clear specimens that are not representative of the behaviour of structural size members with defects. Tests on larger-scale specimens have mostly focused on the material properties and not the structural behaviour of subsystems. Advancements in design and construction techniques have greatly contributed to the emergence of taller and safer wood structures which increase potential for blast threat. This thesis presents results on the flexural behaviour of light-frame wood stud walls subjected to shock wave loading using the University of Ottawa shock tube. The emphasis is on the overall behaviour of the wall subsystem, especially the interaction between the sheathing and the studs through the nailed connection. The approach employed in this experimental program was holistic, where the specimens were investigated at the component and the subsystem levels. Twenty walls consisting of 38 mm x 140 mm machine stress-rated (MSR) studs spaced 406 mm on center and sheathed with two different types and sheathing thicknesses were tested to failure under static and dynamic loads. The experimental results were used to determine dynamic increase factors (DIFs) and a material predictive model was validated using experimental data. The implications of the code are also discussed and compared to the experimental data. Once validated, an equivalent single-degree-of-freedom (SDOF) model incorporating partial composite action was used to evaluate current analysis and design assumptions. The results showed that a shock tube can effectively be used to generate high strain-rate flexural response in wood members and that the material predictive model was found suitable to effectively predict the displacement resulting from shock wave loading. Furthermore, it was found that current analysis and design approaches overestimated the wall displacements.

Offshore developments for hydrocarbon resources have now progressed to water depths approaching 2500 m. Due to the difficulties and high cost in recovering high quality samples from deepwater site, there is increasing reliance on in situ tests such as piezocone and full-flow (i.e. T-bar and ball) penetration tests for determining the geotechnical design parameters. This research was undertaken in collaboration with the Norwegian Geotechnical Institute (NGI), as part of a joint industry project, to improve the reliability of in situ tests in determining design parameters and to improve offshore site investigation practice in deepwater soft sediments. In this research, a worldwide high quality database was assembled and used to correlate intact and remoulded shear strengths (measured from laboratory and vane shear tests) with penetration resistances measured by piezocone, T-bar and ball penetrometers. The overall statistics showed similar and low levels of variability of resistance factors for intact shear strength (N-factors) for all three types of penetrometer. In the correlation between the remoulded penetration resistance and remoulded shear strength, the resistance factors for remoulded shear strength (Nrem-factors) were found higher than the N-factors. As a result, the resistance sensitivity is less than the strength sensitivity. The correlations between the derived N-factors and specific soil characteristics indicated that the piezocone N-factors are more influenced by rigidity index than those for the T-bar and ball penetrometers. The effect of strength anisotropy is only apparent in respect of N-factors for the T-bar and ball penetrometers correlated to shear strengths measured in triaxial compression. On the other hand, the Nrem-factors showed slight tendency to increase with increasing strength sensitivity but were insensitive to soil index properties. These findings suggest that the full-flow penetrometers may be used to estimate remoulded shear strength and are potentially prove more reliable than the piezocone in estimating average or vane shear strength for intact soil but the reverse is probably true for the estimation of triaxial compression strength.

Η σφυρηλάτηση με βολή σωματιδίων (shot peening) είναι μία επιφανειακή κατεργασία που πραγματοποιείται με σκοπό την αύξηση της αντοχής μεταλλικών υλικών και εφαρμόζεται στο τελευταίο στάδιο της γραμμής παραγωγής. Η αύξηση της αντοχής επιτυγχάνεται με την ανάπτυξη θλιπτικών παραμενουσών τάσεων κοντά στην επιφάνεια του υλικού έπειτα από την κρούση σωματιδίων με υψηλές ταχύτητες. Η ανάπτυξη θλιπτικών παραμενουσών τάσεων αυξάνει την αντοχή σε κόπωση, σε εργοδιάβρωση, καθώς και σε άλλες μηχανικές καταπονήσεις και επιτρέπει την μείωση του βάρους σχεδιάζοντας διατομές με μικρότερο πάχος. Στην παρούσα Διδακτορική Διατριβή παρουσιάζεται μια ολοκληρωμένη αριθμητική προσομοίωση της κατεργασίας και εξετάζεται η μηχανική συμπεριφορά των υπό κατεργασία υλικών σε υψηλούς ρυθμούς καταπόνησης. Συγκεκριμένα η μεθοδολογία που αναπτύσσεται περιλαμβάνει την ανάπτυξη ενός αριθμητικού προτύπου για την προσομοίωση της κατεργασίας της σφυρηλάτησης με βολή σωματιδίων και τον υπολογισμό των αποτελεσμάτων της στο υλικό. Τα βήματα που ακολουθηθήκαν για την ανάπτυξη του αριθμητικού προτύπου είναι, α) ο χαρακτηρισμός του κράματος αλουμινίου 7449-Τ7651 σε υψηλούς ρυθμούς καταπόνησης μέσω της πειραματικής διάταξης Split Hopkinson Bar που σχεδιάστηκε και κατασκευάστηκε στο Εργαστήριο Τεχνολογίας και Αντοχής Υλικών, β) η ανάπτυξη βοηθητικών επιμέρους αριθμητικών μοντέλων, γ) η ανάπτυξη κινηματικών μοντέλων προσομοίωσης της ροής των σωματιδίων, δ) η ανάπτυξη κριτηρίων και η εφαρμογή τους για τον υπολογισμό του ελαχίστου απαιτούμενου αριθμού σωματιδίων για την προσομοίωση, καθώς και των θέσεων κρούσης, ε) η ανάπτυξη ενός αριθμητικού προτύπου πλήρους γεωμετρίας της πλάκας για την κρούση του απαιτούμενου αριθμού σωματιδίων και στ) η πειραματική επαλήθευση του αριθμητικού προτύπου. Με το αριθμητικό πρότυπο που αναπτύχτηκε υπολογίστηκαν τα αποτελέσματα της κατεργασίας της σφυρηλάτησης με βολή σωματιδίων στο υλικό και επιβεβαιώθηκαν μέσω συγκρίσεων με αντίστοιχα πειραματικά αποτελέσματα. Αποτελέσματα της κατεργασίας εκτός από τις παραμένουσες τάσεις αποτελούν και η πλαστική παραμόρφωση, η σκληρότητα, η επιφανειακή τραχύτητα και κατ' επέκταση ο συντελεστής έντασης τάσης. Στη συνέχεια, πραγματοποιήθηκε μια παραμετρική μελέτη για την επίδραση της διαμέτρου, της ταχύτητας και της γωνίας κρούσης στην ανάπτυξη των παραμενουσών τάσεων. Επίσης το αριθμητικό πρότυπο επαληθεύτηκε και για άλλα μεταλλικά υλικά. / Shot peening is a surface treatment process that is performed to increase the strength of metallic materials and is applied to the last stage of the production line (post manufacturing process). The increase in strength is achieved by the developed compressive residual stresses near the surface and the subsurface of the treated material after the impact of small diameter particles with high speeds. The developed compressive residual stresses increases the fatigue strength, the mechanical performance of the component under stress corrosion cracking (SCC), under higher stresses and allows lighter structure design. This PhD thesis presents a comprehensive numerical simulation of the Shot peening process and includes a comprehensive study of the mechanical behaviour of treated materials under high strain rates of deformation. Specifically, the methodology developed includes the development of a comprehensive numerical model to simulate Shot peening treatment and calculate the results on the treated material. The steps followed for the development of the numerical model are: a) the characterization of the Aluminium alloy 7449-T7651 at high strain rates using a Split Hopkinson Bar apparatus designed and built at the Laboratory of Technology and Strength of Materials, b) the development of auxiliary partial numerical models, c) the development of a kinematic simulation model for the analysis of the flow particles, d) the development and the application of two criteria for the successful calculation of the minimum number of particles that required for the simulation, and the impact positions e) the development of a numerical model describing the full plate geometry for the impact of the minimum number of particles required and f) the experimental verification of the numerical model. The process outcomes and results on the treated material were calculated by the numerical model developed. The numerical results that were calculated for the threaded material were confirmed by comparison with experimental results. Treatment results include the residual stresses, the plastic deformation, hardness, surface roughness, and hence the stress concentration factor. A parametric study on the effect of the diameter, speed and angle of impact to the development of residual stresses was performed. The numerical model was also verified for a number of other metallic materials.

L'Alliage 600 (Ni-15%Cr-10%Fe) est réputé sensible à la Corrosion Sous Contrainte (CSC) en milieu primaire des Réacteurs à Eau Pressurisée (REP). Des études récentes ont montré que la diffusion du chrome était une étape limitante dans la compréhension des mécanismes de CSC. En particulier, le mécanisme d'oxydation interne contrôlé par le taux de défauts local. Dans ce contexte, l'objectif de cette thèse a été de produire des données expérimentales concernant la cinétique de diffusion du chrome en fonction de différents états métallurgiques. Les coefficients de diffusion du chrome ont été mesurés par Spectrométrie de Masse des Ions Secondaires (SIMS) et Spectrométrie à Décharge Luminescente (SDL) en volume et aux joints de grains dans la gamme de température 678 K-1060 K sur des échantillons en nickel pur et d'Alliage 600 monocristallin ou polycristallin. Une partie de cette thèse s'est focalisée sur l'effet de la déformation plastique sur la cinétique de diffusion du chrome pour des échantillons en nickel monocristallin (orienté <101>). Les expériences de diffusion ont été réalisées sur des échantillons non déformés, pré-écrouis à 4% et 20% de déformation plastique et sur des essais in-situ de diffusion en fluage. Les résultats ont montré que les coefficients de diffusion mesurés sur les éprouvettes déformées plastiquement sous charge constante sont supérieurs de six ordres de grandeur à ceux obtenus à l'état non déformé ou pré-écroui. L'accélération de la cinétique de diffusion peut être attribuée à un couplage entre la mobilité des dislocations et la vitesse de déformation plastique. / Alloy 600 (Ni-15%Cr-10%Fe) is known to be susceptible to Stress Corrosion Cracking (SCC) in primary water of Pressurized Water Reactors (PWR). Recent studies have shown that chromium diffusion is a controlling rate step in the comprehension of SCC mechanism. In order to improve the understanding and the modelling of SCC of Alloy 600 in PWR primary medium the aim of this study was to collect data on kinetics diffusion of chromium. Volume and grain boundary diffusion of chromium in pure nickel and Alloy 600 (mono and poly-crystals) has been measured in the temperature range 678 K to 1060 K by using Secondary Ions Mass Spectroscopy (SIMS) and Glow Discharge-Optical Spectrometry (GD-OES) techniques. A particular emphasis has been dedicated to the influence of plastic deformation on chromium diffusion in nickel single crystals (orientated <101>) for different metallurgical states. The experimental tests were carried out in order to compare the chromium diffusion coefficients in free lattice (not deformed), in pre-hardening specimens (4% and 20%) and in dynamic deformed tensile specimens at 773 K. It has been found that chromium diffusivity measured in dynamic plastic deformed creep specimens were six orders of magnitude greater than those obtained in not deformed or pre-hardening specimens. The enhancement of chromium diffusivity can be attributed to the presence of moving dislocations generated during plastic deformation.

Alloys of titanium are highly preferred materials for their excellent strength to weight ratio but the tribological issues while using them has been posing challenging issues for the tribological analyst, which are still areas of active research. Ti-6Al-4V (Ti64) is the most popular alloy of titanium and our understanding of the fundamental mechanisms of wear and friction of this alloy is still not complete. Previous investigations related to the tribology of these alloys have suggested a synergistic effect of plastic deformation and tribo-oxidation. The present investigation described in this thesis explores the existence of one more mode, namely the formation of a Mechanically Mixed Layer (MML). The thesis examines the effect of these modes one by one and analyses the synergistic effect of these mechanisms, and also the effect of heat generation during sliding. The tribological condition existing have been varied by doing wear experiments using Ti64 pins sliding against alumina and SS316L (controls MML), diameter of pin (expected to control debris entrapment and thus MML formation), tribo-system (horizontal disc Vs vertical disc, which is also expected to control debris entrapment and thus MML formation), environment (ambient and vacuum, expected to control tribo-oxidation) and sliding speed (expected to control interface temperature and thus plastic deformation mechanism and tribo-oxidations). The division of the main chapters has been so made to present the findings spread over Chapters 5-8, with each chapter dealing with specific tribological test conditions. In each chapter, results from the tribological experimentations in the form of wear and friction are presented, together with the characterization methods which throw light into the tribological mechanisms. These characterization methods include Scanning Electron Microscopy (SEM), Energy Dispersive X-ray Spectroscopy (EDAX), X-Ray Diffraction (XRD) and Electron probe micro-analyzer (EPMA). Wherever possible, the debris collected from the experiments have been subjected to morphological and detailed chemical analysis, and a feature which has not been explored much in detail by tribological investigators, but having a promising potential. Experimental results from tribological testing when Ti64 pins slides against two different materials (Alumina and SS316L) in pin-on-disc tribometers under two different environmental conditions (ambient /vacuum) are analyzed. Each set of experiments looks at two different effects - (1) the effect of sliding speed on the tribological behavior while using a pin of a fixed diameter (all other parameters remaining the same) and (2) the effect of using pins of different diameters for a given set of parameters. Three different pin-sizes were employed (2.1 mm. 4.6 mm and 6.6 mm), the normal loads on these pins were changed according to the pin-size used so that all experiments were done at the same contact pressure (2.8 MPa). By performing the experiments against the ceramic disc (alumina) under vacuum conditions, the effect of this plastic deformation is studied in isolation because the possibility of the Tribo Chemical Reaction (TCR) due to oxidation is inhibited and no MML was found to be formed due to poor compatibility of mixing between the metallic pin and the ceramic disc. For the low speeds/strain rates experiments, the effect of plastic deformation as influenced by the adiabatic shear banding is seen to influence wear which progressively changes to temperature induced plastic deformation and wear. The situation is found to be different when we change the environmental conditions from vacuum to ambient for the same tribo-combination. The tests shows a reduction in wear rate with speed, and this is due to the oxide formations due to TCR as confirmed from the SEM/EDAX characterization. In contrast to previous experiments under vacuum, these permit the effect of TCR also to influence the tribological behavior. The scenario changes when the alumina disc is replaced by a metallic one (SS316L) and tests carried out in vacuum, as the MML was found to be formed with this tribo-pair. Because of the mutual affinity of the materials in the tribo-pair, the wear damage is severe in this case and the flash temperatures crossing the phase transition temperature (~880oC) for Ti64 at high speeds. The growth of the β phase with increase in the sliding (temperature) conditions is captured from the XRD spectra of the wear debris. Synergistic effect of all these mechanisms (plastic deformation, MML, and TCR) is permitted by conducting experiments with Ti64 pin against stainless steel and in ambient conditions. A comparison of the tribological response by presenting results when experiments are run over a range of speeds while using different sized pins under ambient conditions (and compared with similar results in vacuum) while using SS316L disc serve to demarcate the differences in the wear modes which are active/inactive depending on the tribological conditions. In addition a study incorporating the effect of frictional heating and its influence on the tribological phenomena is analyzed. Main conclusions from the thesis are: The wear resistance of Ti64 alloy when sliding against SS316L is found to be influenced by Strain Rate Response (SRR), Tribo Oxidation (TO), Mechanically Mixed Layer (MML) and the prevailing heat flux conditions at the contact. The wear rates were found to decrease marginally with sliding speeds (strain rates) up to a certain speed, which is ascribed to reduction in adiabatic shear band intensity with increase in strain rate. Adiabatic Shear Band (ASB), which allows easy crack propagation, intensity reduces as temperature of deformation of Ti64 is increased. From the results it can be confirmed that the propensity for formation of MML depends on compatibility of the disc and the pin material. The contribution due to of entrapment and retention of debris in the contact zone also would influence formation of the MML. The effect of frictional heating plays an influential role as it can affect the factors (TO, ASB, MML) governing the tribological response. The sensitivity to temperature, which is a marked feature of this alloy in undergoing softening, as confirmed by previous researchers, is reflected in the experimental results. Since the main factor that triggers the micro-structural instability is the energy dissipation that accompanies deformation more fundamental research which can improve the thermal transport properties of this alloy, would be the future scope of work of this thesis. Also, the unique composition of the MML which offers high wear resistance under specific operating conditions opens up the possibility of new such alloy formulations, production routes and techniques which should improve the tribological response of this alloy.

Deliberate and accidental explosions along with the heightened risk of loss of life and property damage during such events have highlighted the need for research in the behaviour of materials under high strain rates. Where an extensive body of research is available on steel and concrete structures, little to no details on how to address the design or retrofitting of wood structures subjected to a blast threat are available. Studies reported in the literature that focused on full scale light-frame wood structures did not quantify the increase in capacity due to the dynamic loading while the studies that did quantify the increase mostly stems from small clear specimens that are not representative of the behaviour of structural size members with defects. Tests on larger-scale specimens have mostly focused on the material properties and not the structural behaviour of subsystems. Advancements in design and construction techniques have greatly contributed to the emergence of taller and safer wood structures which increase potential for blast threat. This thesis presents results on the flexural behaviour of light-frame wood stud walls subjected to shock wave loading using the University of Ottawa shock tube. The emphasis is on the overall behaviour of the wall subsystem, especially the interaction between the sheathing and the studs through the nailed connection. The approach employed in this experimental program was holistic, where the specimens were investigated at the component and the subsystem levels. Twenty walls consisting of 38 mm x 140 mm machine stress-rated (MSR) studs spaced 406 mm on center and sheathed with two different types and sheathing thicknesses were tested to failure under static and dynamic loads. The experimental results were used to determine dynamic increase factors (DIFs) and a material predictive model was validated using experimental data. The implications of the code are also discussed and compared to the experimental data. Once validated, an equivalent single-degree-of-freedom (SDOF) model incorporating partial composite action was used to evaluate current analysis and design assumptions. The results showed that a shock tube can effectively be used to generate high strain-rate flexural response in wood members and that the material predictive model was found suitable to effectively predict the displacement resulting from shock wave loading. Furthermore, it was found that current analysis and design approaches overestimated the wall displacements.