Thèse numérisée par la Division de la gestion de documents et des archives de l'Université de Montréal

This thesis has the dual purpose of raising awareness of the importance of the mixing protocol on the end products of polyelectrolyte-oppositely charged surfactant systems, and to contribute to a better understanding of the properties of bottle-brush polyelectrolytes when adsorbed onto interfaces. In the first part of this thesis work, the effects of the mixing protocol and the mixing procedure on formed polyelectrolyte-oppositely charged surfactant aggregates were investigated. It was shown that the initial properties of the aggregates were highly dependent on the mixing parameters, and that the difference between the resulting aggregates persisted for long periods of time. The second part of the studies was devoted to the surface properties of a series of bottle-brush polyelectrolytes made of charged segments and segments bearing poly(ethylene oxide) side chains; particular attention was paid to the effect of side chain to charge density ratio of the polyelectrolytes. It was shown that the adsorbed mass of the polyelectrolytes, and the corresponding number of poly(ethylene oxide) bearing segments at the interface, went through a maximum as the charge density of the polyelectrolyte was increased. Also, it was found that bottle-brush polyelectrolyte layers were desorbed quite easily when subjected to salt solutions. This observation was rationalized by the unfavourable excluded volume interactions between the side chains and the entropic penalty of confining them at an interface, which weaken the strength of the binding of the polyelectrolytes to the interface. However, it was shown that the same side chains effectively protect the adsorbed layer against desorption when the layer is exposed to solutions containing an oppositely charged surfactant. Investigation of the lubrication properties of the bottle-brush polyelectrolytes in an asymmetric (mica-silica) system also related the observed favourable frictional properties to the protective nature of the side chains. The decisive factor for achieving very low coefficients of friction was found to be the concentration of the side chains in the gap between the surfaces. Interestingly, it was shown that a brush-like conformation of the bottle-brush polyelectrolyte at the interface has little effect on achieving favourable lubrication properties. However, a brush-like conformation is vital for the resilience of the adsorbed layer against the competitive adsorption of species with a higher surface affinity. / QC 20100830

The object of this thesis is to apply scanning probemicroscopy (SPM) to the field of advanced powder processing.Measurement of interparticle surface forces at conditionsrelevant to ceramic processing has been performed together withthorough studies of powder friction. Surface force measurements between silicon nitride andsilica surfaces in 1-bromonaphtalene and diiodomethane resultedin an attractive van der Waals force in both media for thesymmetric systems and a repulsive van der Waals force for theasymmetric systems. This agreed well with theoreticalpredictions from Lifshitz theory. Measurements in electrolytesolutions between silicon nitride surfaces with a varyingdegree of oxidation showed that silanol groups dominated theinteractions at a high degree of oxidation, whereas theinfluence of amine species became stronger after surfaceetching. Surface charge, surface potential and density ofsurface groups have been extracted from DLVO computer modellingof the experimental force curves. Surface force measurementshave been carried out using a nitrided silica sphere as acolloidal probe, representative for commercial silicon nitridepowders. Adsorption of poly(acrylic acid) above the isoelectricpoint generated a thin polymer layer of an essentially flatconformation. Friction force measurements were attainable via novelcalibration procedures of both the lateral photodetectorresponse and the cantilever torsional spring constant.Combining the method for detector calibration with evaluationof static friction slopes simplified the choice of appropriatecontact mechanics theory to evaluate the friction measurements.Applying the method on friction measurements between ironsurfaces coated with commercial lubricants showed a substantialsurface deformation not seen from the friction force alone. Thenanorheological properties of silica surfaces coated with twodifferent stearic acids have been evaluated from friction forcemeasurements. Steady sliding motion was replaced by highlyregular stick-slip motion at a critical load and velocity. Thestick-slip motion was successfully described and fitted to aphenomenological model. The contact area evaluated fromMaugis-Dugdale theory revealed the contact diameter to be veryclose to the stick-slip periodicity. Friction measurements were carried out between individualspray-dried ceramic granules as a function of binderconcentration and relative humidity. The hygroscopic nature ofthe binder resulted in a higher adhesion force but lowerfriction coefficient with increasing humidity. This effect wasascribed to softening of the binder and a lowering of the shearstrength of the binder rich surface layer on the granules.Comparison of the friction force between two granules and agranule and a hard metal surface confirmed that resistance toflow during the initial stages of powder pressing is dominatedby granule-wall friction and adhesion. Keywords: Atomic force microscope, AFM, SPM, van der Waalsinteraction, DLVO-theory, surface forces, colloidal probe,force curve, friction, adhesion, stick-slip, cantilever,calibration, spring constant, silicon nitride, iron,silica.

The first part of this thesis is concerned with thestructure-property relationships in nonionic surfactantsystems. The main aim was to investigate how the surfactantstructure influences the adsorption at interfaces andinteractions between surfactant coated interfaces.Particularly, the effect of the structure of the surfactantheadgroups was investigated. These were sugar-based headgroupwith varying size and flexibility and poly(ethylene oxide)based headgroups with or without an additional amide or estergroup. The hydrophobic part of the surfactant consisted mostlyof straight alkyl chains, except for one type of poly(ethyleneoxide) based surfactant with a dehydroabietic hydrophobe. The main technique that was used is the surface forcetechnique, with which the forces acting between two adsorbedsurfactant layers on hydrophilic or hydrophobic surfaces can bemeasured. These forces are important for e.g. the stability ofdispersions. The hydrophilic surfaces employed were glass andmica, whereas the hydrophobic surfaces were silanized glass andhydrophobized mica. The adsorption behavior on hydrophilicsurfaces is highly dependent on the type of headgroup andsurface, whereas similar results were obtained on the two typesof hydrophobic surfaces. To better understand how the surfaceforces are affected by the surfactant structure, measurementsof adsorbed amount and theoretical mean-field latticecalculations were carried out. The results show that the sugarsurfactant layers and poly(ethylene oxide) surfactant layersgive rise to very different surface forces, but that the forcesare more similar within each group. The structure-propertyrelationships for many other physical properties have beenstudied as well. These include equilibrium and dynamicadsorption at the liquid-vapor interface, micelle size, micelledynamics, and wetting. The second part in this thesis is about the aggregationbetween cationic polyelectrolytes and an anionic surfactant.The surface force technique was used to study the adsorption ofa low charged cationic polyelectrolyte on mica, and theaggregation between the adsorbed polyelectrolyte with theanionic surfactant. The aggregation in bulk was studied withturbidimetry, small angle neutron scattering (SANS), and smallangle x-ray scattering (SAXS). An internal hexagonal aggregatestructure was found for some of the bulk aggregates. <b>Keywords:</b>nonionic surfactant, sugar surfactant,poly(ethylene oxide), amide, ester, polyelectrolyte, SDS,hydrophobic surface, glass surface, mica, adsorption,aggregation, micelle size, surface forces, wetting, dynamicsurface tension, NMR, TRFQ, SANS, SAXS, mean-field latticecalculations.

The structure and dynamics of the smectic-A liquid crystal 8CB (4 cyano-4 octylbiphenyl) when sheared and confined to mesoscale gaps (with crossed cylindrical geometry and mica confining surfaces) were studied using a Surface Forces Apparatus (SFA). Triangular shear patterns with frequencies of 0.01, 0.1, 1.0 and 10 Hz, and amplitudes of 62.5 nm, 625 nm and 6.25 m were applied to samples at gap sizes of 0.5 and 5.0 m. The study was performed at room temperature (20.5C) and at two higher temperatures (22C and 27C). In order to minimize the thermal fluctuations within the test chamber and hence to allow for the rapid re-initialization of test runs, the SFA was modified to allow for quick, precise and remote control of the confining surfaces. The procedure maximized the number of tests that could be undertaken with a single pair of surfaces so that a single gap geometry could be maintained for the duration of the test run. In order to run the SFA remotely, scripts written with a commercial software package, LabVIEW, were used to control of the SFA components, its FECO-monitoring camera and all its peripheral electronic equipment as well. Samples were agitated to disrupt any shear-induced liquid crystal domain alignment from previous testing following each shear test, and methodologies were developed to ascertain the extent of confinement quickly and remotely following agitation. Separate methods were developed for gap sizes at each extreme of the mesoscale regime, where the transition from bulklike structure and dynamics to nano-confinement occurs (between 1 and 10 microns for smectic-A 8CB). The results revealed that the greater amplitude-gap aspect ratio and surface-to-domain contact associated with smaller gaps facilitated reorientation of the domains in the shear direction. Evidence was also presented of domains at the higher end or outside of the mesoscale regime that, while straining and accreting, were unable to reorient and thereby led to an overall increase of viscoelastic response. The effective viscosity was found to obey a simple power law with respect to shear rate, , and the flow behaviour indices, n, slightly in excess of unity indicate shear thickening occurs with large enough shear amplitude, and that the viscosity reached a plateau near unity over shear rates of 0.005 to 500 s-1 within the mesoscale regime. Different K and n values were observed depending on the shear amplitude used. Unlike bulk smectic 8CB, whose domains do not align well in the shear direction with large shear-strain amplitude, at mesoscale levels of confinement large amplitude shearing (up to 12.5 shear strain amplitude) was found to be very effective at aligning domains. In general domain reorientation is found to be much more rapid within the mesoscale regime than has been reported in bulk. Aggressive shearing was found to result in a complete drop in viscoelastic response within seconds, while gentler shearing is found to produce a very gradual increase that persists for more than six hours, with individual shear periods exhibiting frequent and significant deviations from the expected smooth shear path that may be a product of discrete domain reorientations. From these findings, certain traits of the smectic 8CB domain structures under mesoscale confinement were deduced, including how they respond to shear depending on the level of confinement, and how their reorientation due to shear varies not only with shear rate but also independently with shear amplitude. An equation describing the viscosity change as a function of both shear rate and shear amplitude is proposed. The shear amplitude dependence introduces the notion of shearing beyond the proposed smectic 8CB “viscoelastic limit”, which was shown to exhibit behaviour in accordance with Large Amplitude Oscillatory Shear (LAOS) techniques developed for Fourier Transform rheology. The findings provided an understanding of the behavioural changes that occur as one reduces the level of confinement of smectic materials from bulk to nanoconfinement.

<p>The object of this thesis is to apply scanning probemicroscopy (SPM) to the field of advanced powder processing.Measurement of interparticle surface forces at conditionsrelevant to ceramic processing has been performed together withthorough studies of powder friction.</p><p>Surface force measurements between silicon nitride andsilica surfaces in 1-bromonaphtalene and diiodomethane resultedin an attractive van der Waals force in both media for thesymmetric systems and a repulsive van der Waals force for theasymmetric systems. This agreed well with theoreticalpredictions from Lifshitz theory. Measurements in electrolytesolutions between silicon nitride surfaces with a varyingdegree of oxidation showed that silanol groups dominated theinteractions at a high degree of oxidation, whereas theinfluence of amine species became stronger after surfaceetching. Surface charge, surface potential and density ofsurface groups have been extracted from DLVO computer modellingof the experimental force curves. Surface force measurementshave been carried out using a nitrided silica sphere as acolloidal probe, representative for commercial silicon nitridepowders. Adsorption of poly(acrylic acid) above the isoelectricpoint generated a thin polymer layer of an essentially flatconformation.</p><p>Friction force measurements were attainable via novelcalibration procedures of both the lateral photodetectorresponse and the cantilever torsional spring constant.Combining the method for detector calibration with evaluationof static friction slopes simplified the choice of appropriatecontact mechanics theory to evaluate the friction measurements.Applying the method on friction measurements between ironsurfaces coated with commercial lubricants showed a substantialsurface deformation not seen from the friction force alone. Thenanorheological properties of silica surfaces coated with twodifferent stearic acids have been evaluated from friction forcemeasurements. Steady sliding motion was replaced by highlyregular stick-slip motion at a critical load and velocity. Thestick-slip motion was successfully described and fitted to aphenomenological model. The contact area evaluated fromMaugis-Dugdale theory revealed the contact diameter to be veryclose to the stick-slip periodicity.</p><p>Friction measurements were carried out between individualspray-dried ceramic granules as a function of binderconcentration and relative humidity. The hygroscopic nature ofthe binder resulted in a higher adhesion force but lowerfriction coefficient with increasing humidity. This effect wasascribed to softening of the binder and a lowering of the shearstrength of the binder rich surface layer on the granules.Comparison of the friction force between two granules and agranule and a hard metal surface confirmed that resistance toflow during the initial stages of powder pressing is dominatedby granule-wall friction and adhesion.</p><p>Keywords: Atomic force microscope, AFM, SPM, van der Waalsinteraction, DLVO-theory, surface forces, colloidal probe,force curve, friction, adhesion, stick-slip, cantilever,calibration, spring constant, silicon nitride, iron,silica.</p>

<p>The first part of this thesis is concerned with thestructure-property relationships in nonionic surfactantsystems. The main aim was to investigate how the surfactantstructure influences the adsorption at interfaces andinteractions between surfactant coated interfaces.Particularly, the effect of the structure of the surfactantheadgroups was investigated. These were sugar-based headgroupwith varying size and flexibility and poly(ethylene oxide)based headgroups with or without an additional amide or estergroup. The hydrophobic part of the surfactant consisted mostlyof straight alkyl chains, except for one type of poly(ethyleneoxide) based surfactant with a dehydroabietic hydrophobe.</p><p>The main technique that was used is the surface forcetechnique, with which the forces acting between two adsorbedsurfactant layers on hydrophilic or hydrophobic surfaces can bemeasured. These forces are important for e.g. the stability ofdispersions. The hydrophilic surfaces employed were glass andmica, whereas the hydrophobic surfaces were silanized glass andhydrophobized mica. The adsorption behavior on hydrophilicsurfaces is highly dependent on the type of headgroup andsurface, whereas similar results were obtained on the two typesof hydrophobic surfaces. To better understand how the surfaceforces are affected by the surfactant structure, measurementsof adsorbed amount and theoretical mean-field latticecalculations were carried out. The results show that the sugarsurfactant layers and poly(ethylene oxide) surfactant layersgive rise to very different surface forces, but that the forcesare more similar within each group. The structure-propertyrelationships for many other physical properties have beenstudied as well. These include equilibrium and dynamicadsorption at the liquid-vapor interface, micelle size, micelledynamics, and wetting.</p><p>The second part in this thesis is about the aggregationbetween cationic polyelectrolytes and an anionic surfactant.The surface force technique was used to study the adsorption ofa low charged cationic polyelectrolyte on mica, and theaggregation between the adsorbed polyelectrolyte with theanionic surfactant. The aggregation in bulk was studied withturbidimetry, small angle neutron scattering (SANS), and smallangle x-ray scattering (SAXS). An internal hexagonal aggregatestructure was found for some of the bulk aggregates.</p><p><b>Keywords:</b>nonionic surfactant, sugar surfactant,poly(ethylene oxide), amide, ester, polyelectrolyte, SDS,hydrophobic surface, glass surface, mica, adsorption,aggregation, micelle size, surface forces, wetting, dynamicsurface tension, NMR, TRFQ, SANS, SAXS, mean-field latticecalculations.</p>

The structure and dynamics of the smectic-A liquid crystal 8CB (4 cyano-4 octylbiphenyl) when sheared and confined to mesoscale gaps (with crossed cylindrical geometry and mica confining surfaces) were studied using a Surface Forces Apparatus (SFA). Triangular shear patterns with frequencies of 0.01, 0.1, 1.0 and 10 Hz, and amplitudes of 62.5 nm, 625 nm and 6.25 m were applied to samples at gap sizes of 0.5 and 5.0 m. The study was performed at room temperature (20.5C) and at two higher temperatures (22C and 27C). In order to minimize the thermal fluctuations within the test chamber and hence to allow for the rapid re-initialization of test runs, the SFA was modified to allow for quick, precise and remote control of the confining surfaces. The procedure maximized the number of tests that could be undertaken with a single pair of surfaces so that a single gap geometry could be maintained for the duration of the test run. In order to run the SFA remotely, scripts written with a commercial software package, LabVIEW, were used to control of the SFA components, its FECO-monitoring camera and all its peripheral electronic equipment as well. Samples were agitated to disrupt any shear-induced liquid crystal domain alignment from previous testing following each shear test, and methodologies were developed to ascertain the extent of confinement quickly and remotely following agitation. Separate methods were developed for gap sizes at each extreme of the mesoscale regime, where the transition from bulklike structure and dynamics to nano-confinement occurs (between 1 and 10 microns for smectic-A 8CB). The results revealed that the greater amplitude-gap aspect ratio and surface-to-domain contact associated with smaller gaps facilitated reorientation of the domains in the shear direction. Evidence was also presented of domains at the higher end or outside of the mesoscale regime that, while straining and accreting, were unable to reorient and thereby led to an overall increase of viscoelastic response. The effective viscosity was found to obey a simple power law with respect to shear rate, , and the flow behaviour indices, n, slightly in excess of unity indicate shear thickening occurs with large enough shear amplitude, and that the viscosity reached a plateau near unity over shear rates of 0.005 to 500 s-1 within the mesoscale regime. Different K and n values were observed depending on the shear amplitude used. Unlike bulk smectic 8CB, whose domains do not align well in the shear direction with large shear-strain amplitude, at mesoscale levels of confinement large amplitude shearing (up to 12.5 shear strain amplitude) was found to be very effective at aligning domains. In general domain reorientation is found to be much more rapid within the mesoscale regime than has been reported in bulk. Aggressive shearing was found to result in a complete drop in viscoelastic response within seconds, while gentler shearing is found to produce a very gradual increase that persists for more than six hours, with individual shear periods exhibiting frequent and significant deviations from the expected smooth shear path that may be a product of discrete domain reorientations. From these findings, certain traits of the smectic 8CB domain structures under mesoscale confinement were deduced, including how they respond to shear depending on the level of confinement, and how their reorientation due to shear varies not only with shear rate but also independently with shear amplitude. An equation describing the viscosity change as a function of both shear rate and shear amplitude is proposed. The shear amplitude dependence introduces the notion of shearing beyond the proposed smectic 8CB “viscoelastic limit”, which was shown to exhibit behaviour in accordance with Large Amplitude Oscillatory Shear (LAOS) techniques developed for Fourier Transform rheology. The findings provided an understanding of the behavioural changes that occur as one reduces the level of confinement of smectic materials from bulk to nanoconfinement.

Submitted by Pedro Silva Filho (pfsilva@ipen.br) on 2017-10-09T19:31:24Z No. of bitstreams: 0 / Made available in DSpace on 2017-10-09T19:31:24Z (GMT). No. of bitstreams: 0 / A marcação por feixe laser em superfícies é utilizada para assegurar a identificação e a rastreabilidade em biomateriais. A texturização via feixe laser confere maior aderência às superfícies dos dispositivos médicos implantáveis. Este trabalho teve o objetivo de avaliar o comportamento da superfície do aço inoxidável austenítico ABNT NBR ISO 5832-1 submetido à marcação e texturização com feixe laser de fibra óptica, alterando-se a frequência dos pulsos; frente ao seu comportamento biomecânico, por meio de: ensaios de resistência à tração, fadiga e desgaste; verificar a susceptibilidade à corrosão localizada, por ensaios eletroquímicos em solução que simula os fluidos corpóreos; e caracterizar a sua microestrutura. Os tratamentos alteraram a rugosidade e a dureza dos biomateriais em função do aumento da frequência dos pulsos. A microestrutura e composição química das superfícies sofreram mudanças que afetaram diretamente a camada passiva dos aços inoxidáveis. Este efeito foi comprovado com o uso de SVET, XPS e caracterização de propriedades eletrônicas do filme passivo. Os dois tipos de tratamentos implicaram em aumento de susceptibilidade magnética das superfícies. Os parâmetros utilizados para as marcações e texturizações não causaram diminuição na viabilidade celular, de modo que não apresentou citotoxicidade mesmo após incubação prolongada. Este biomaterial mostrou-se adequado perante os ensaios biomecânicos, uma vez que os tratamentos a laser, nas condições utilizadas, não induziram a formação de tensões superficiais de magnitude capaz de levar à fratura por fadiga, indicando vida em fadiga infinita; tampouco se pôde relacionar a região de fratura por tração com as marcações a laser. O volume de desgaste diminuiu em função do aumento da dureza produzido pela elevação da frequência do pulso nas texturizações. O caráter visual das marcações e texturizações por feixe laser foi assegurado após a maioria dos ensaios realizados. / Tese (Doutorado em Tecnologia Nuclear) / IPEN/T / Instituto de Pesquisas Energéticas e Nucleares - IPEN-CNEN/SP

La tendance à la miniaturisation des produits n'est pas sans influence sur l'évolution de leurs moyens de production et d'assemblage. En effet, dû à la réduction d'échelle, l'assemblage de petits composants (appelé microassemblage) est perturbé par les forces de surface comme les forces de capillarité. Ces forces, exercées par le pont liquide reliant manipulateur et composant, sont habituellement négligeables (et négligées) dans l'assemblage conventionnel dominé par les forces de gravité. L'approche originale suivie dans ce travail consiste à tirer parti de ces effets et à les utiliser pour la manipulation de microcomposants, c'est-à-dire de composants dont la taille va de quelques dizaines de microns à quelques millimètres. Ce travail tente donc d'apporter quelques réponses aux problèmes de conception posés par un tel choix: quels sont les avantages d'une telle approche? Comment ces forces `fonctionnent-elles'? Sont-elles suffisamment grandes pour manipuler des microcomposants? Comment, dans ce cas, relâcher le composant? Quel rôle la tension de surface joue-t-elle? En quoi le choix des matériaux est-il important? Comment optimiser la conception du manipulateur? Tout au long de ce travail, le lecteur trouvera un inventaire des principes de manipulation existants, les éléments nécessaires à la modélisation des forces de capillarité, ainsi que la description de la simulation et du banc d'essai développés par l'auteur dans le but d'étudier ces paramètres de conception. Les résultats présentés dans cette thèse recouvrent essentiellement deux thèmes: quelles sont les règles de conception à suivre pour maximiser les forces de capillarité (problème de la préhension) et comment choisir une stratégie de relâche adéquate (problème de la relâche)? / Doctorat en sciences appliquées / info:eu-repo/semantics/nonPublished