Nesta dissertação apresenta-se um estudo sobre o desempenho dinâmico do sistema elétrico de potência, frente à conexão de um parque eólico ligado através de conversores de frequência e de geradores síncronos de fontes hidrelétricas e termoelétricas. Dependendo da forma com que é gerenciado, este tipo de geração pode causar impactos significativos no sistema de energia elétrica. Este trabalho analisa o comportamento da estabilidade transitória nos sistemas de potência do ponto de vista da geração com inserção de fontes renováveis. Um sistema elétrico é proposto com dados reais do Rio Grande do Sul e modelado nos programas ANAREDE e ANATEM, considerando seus principais componentes, entre eles, linhas de transmissão, cargas, geradores e transformadores. São utilizadas estratégias de controle do programa ANATEM para a operação dos mesmos e estudar o comportamento do sistema elétrico de potência frente a diferentes eventos. Simulações são realizadas para investigar a influência de diversos fatores na resposta transitória do sistema. Os fatores analisados são: tempo de eliminação da falta, carregamento do sistema, níveis de geração das fontes tradicionais e das fontes eólicas. A análise dos resultados mostrara o impacto deste tipo de fontes instaladas no sistema em regime permanente e transitório. / This thesis introduces a study of an electric power system’s dynamic performance with traditional generation sources (hydro and thermoelectric) and wind farms. Depending on how it is managed, significant impact in the electric power system may occur. The power system transient stability is analyzed in this thesis considering the insertion of renewable energy resources. An equivalent power system is proposed with real data of Rio Grande do Sul and modeled using ANAREDE and ANATEM software, including as its main components, transmission lines, loads, generators and transformers. The control strategies present in the software ANATEM are used for the operation of these components, and then, to study the behavior of the electric power system against different events. Simulations are performed to investigate the influence of various factors on the transient response of the system. The factors analyzed are: time of fault clearing, system load, generation levels from traditional sources and wind sources. The analysis of the results shows the impacts of these specific resources in the system performance for steady state operation and transient state.

Orientador: Walmir de Freitas Filho / Dissertação (mestrado) - Universidade Estadual de Campinas, Faculdade de Engenharia Elétrica e de Computação / Made available in DSpace on 2018-08-17T13:40:40Z (GMT). No. of bitstreams: 1 Morais_CeciliadeFreitas_M.pdf: 1237482 bytes, checksum: caa2c7e10679e865b870669fb557c361 (MD5) Previous issue date: 2011 / Resumo: Um dos distúrbios mais freqüentes acarretados pela partida direta de grandes motores de indução é o afundamento de tensão decorrente das elevadas correntes de energização drenadas pelos mesmos durante a fase inicial de aceleração. Essas variações da magnitude de tensão podem deteriorar a operação de cargas sensíveis, geradores e relés digitais existentes em instalações industriais. Portanto, sempre que um novo motor de indução é conectado em uma instalação industrial, os engenheiros de planejamento estão interessados em saber se esse procedimento irá resultar em níveis aceitáveis de afundamentos de tensão. O impacto da partida do motor de indução na qualidade de energia pode ser avaliado por estudos que exigem complexas e numerosas simulações de transitórios eletromagnéticos, o que demanda um considerável tempo de mão de obra altamente especializada. Nesse contexto, o objetivo dessa dissertação de mestrado é desenvolver métodos analíticos e gráficos confiáveis e práticos que auxiliem os engenheiros de planejamento nos projetos de instalação e de partida de motores de indução em instalações industriais com cargas sensíveis a variações de tensão. Tais métodos foram desenvolvidos para análise de motores de indução do tipo gaiola de esquilo com partida direta, tendo em vista que esse é um esquema bastante adotado devido ao seu baixo custo e simplicidade. Os métodos analíticos são desenvolvidos através da solução dos modelos matemáticos de regime permanente e dinâmicos dos diversos componentes da instalação industrial. A precisão dos métodos analíticos propostos é verificada através da comparação dos respectivos resultados com aqueles obtidos através de simulações de transitórios eletromagnéticos. O objetivo dos métodos gráficos é facilitar a compreensão das informações relacionadas ao comportamento dinâmico da tensão através de gráficos semelhantes aos tipicamente utilizados na análise de qualidade de energia (e.g., ITIC - Information Technology Industry Council) / Abstract: One of the most common disturbances caused by the starting of large induction motors is the voltage sag that occurs due to the high inrush current. These variations in voltage and current magnitude can deteriorate the operation of generators, sensitive loads and digital relays in industrial facilities. Therefore, whenever a new induction motor is connected to the system, planning engineers want to know if the motor starting would result in acceptable voltage sag levels. The impact of the induction motors starting on the power quality can be assessed by studies that require numerous and complex electromagnetic transient simulations, which is very time-consuming. In this context, the objective of this work is to develop simple graphical and analytical methods to assist planning engineers when analyzing the installation of new induction motors in industrial facilities. This work will focus on squirrel-cage induction motors with direct start, since this scheme is extremely adopted due to its low cost and simplicity. The analytical methods are developed through the solution of the steady state and dynamic models of the several components of the industrial facility. The accuracy of the analytical methods proposed is validated through comparison with the results obtained by repetitive electromagnetic transient simulations. The objective of the methods is to facilitate the understanding of the information obtained about the dynamic behavior of the voltage through charts typically used in the analysis of power quality (e.g., ITIC - Information Technology Industry Council). / Mestrado / Energia Eletrica / Mestre em Engenharia Elétrica

Orientadores: Andre Luiz Morelato França, Walmir de Freitas Filho / Tese (doutorado) - Universidade Estadual de Campinas, Faculdade de Engenharia Eletrica e de Computação / Made available in DSpace on 2018-08-06T02:54:55Z (GMT). No. of bitstreams: 1 VieiraJunior_JoseCarlosdeMelo_D.pdf: 1983649 bytes, checksum: 2abfcaa471b650a7138b798950c476a7 (MD5) Previous issue date: 2006 / Resumo: Uma das principais funções dos sistemas de proteção de geradores distribuídos conectados em redes de subtransmissão ou de distribuição de energia elétrica é desconectá-los tão logo uma situação de ilhamento seja detectada. O ilhamento ocorre quando parte da rede elétrica é desconectada do restante do sistema da concessionária, mas continua a ser energizada por um ou mais geradores distribuídos conectados a ela, formando um subsistema isolado da concessionária. Esta ocorrência deve ser evitada porque coloca em risco a segurança de pessoas e equipamentos e pode deteriorar a qualidade da energia suprida aos consumidores locais. Neste contexto, esta tese de doutorado propõe novas metodologias para avaliar de forma sistemática e ajustar alguns dos principais relés de proteção anti-ilhamento de geradores síncronos. As técnicas analisadas compreendem os relés de deslocamento de fase ou ¿salto de vetor¿, relés de taxa de variação de freqüência, relés de sub/sobrefreqüência convencionais e os relés de sub/sobretensão convencionais. A aplicação das metodologias desenvolvidas mostrou que elas são ferramentas eficientes para avaliar e determinar o desempenho desses relés quanto à detecção de ilhamentos, auxiliando na seleção dos esquemas de proteção e ajustes mais adequados / Abstract: One of the main functions of distributed generators¿ protection systems is the capability to disconnect the generators immediately after an islanding occurrence is detected. Islanding occurs when a portion of the distribution system is disconnected from the utility grid, yet remains energized by one or more distributed generators connected to it. This operating condition should be avoided because it poses safety risks to utility personnel and equipments as well as it can cause power quality problems to the local costumers. In this context, this thesis proposes new methodologies to systematically evaluate and adjust some anti-islanding techniques applied to synchronous generators. The techniques analyzed are the under/over frequency relays, the rate of change of frequency (ROCOF) relays, the vector surge or vector jump relays and the under/overvoltage relays. The results have shown that the proposed methodologies can be efficient tools to evaluate and to determine the performance of these anti-islanding relays, consequently, they can help protection engineers to select the most proper protection devices and their settings / Doutorado / Energia Eletrica / Doutor em Engenharia Elétrica

Synchronous generators have been used in hydropower from more than a century where, traditionally, the field current is transferred to the rotor using slip rings and carbon brushes. There are some major disadvantages following the use static excitation; regular and expensive maintenance, as well as a source of carbon dust which, due to buildup, may cause short circuits. To avoid these problems associated with slip ring exciter systems, a system that use induction to transfer power to the rotor could be used instead. Systems that utilize brushless excitation today usually regulates the current by controlling the magnetization of the exciter stator, which is comparably slower than their static counterparts. In order to allow for swift regulation of the field current from a brushless exciter, required power electronics and controllers have to be present on the rotor shaft instead. The aim of this project is to start investigating if commercially available products, which are originally indented to be used in a stationary environment, could accomplish this. The results from this study shows that it is possible to use such products to control the field current. The components were found to withstand the exposure of high g-forces and vibrations, albeit only during the relatively small amount of time in which rotary testing was performed. As such there is no certainty that the components would remain functional for the considerably longer time that any commercial use would require them to.

DC power systems have a constant DC-link voltage, as well as the advantages such as high stability, high efficiency, small size and light weight; therefore, they are widely used in stand-alone power systems, e.g. the power systems in aircrafts and automobiles, isolated wind power generation systems, etc. Permanent-Magnet Synchronous Generators (PMSGs) possess the advantages including high power density, high efficiency, and high control precision, and have obtained great attention and have been widely used in military, inductry, and daily life. Pulse Width Modulation (PWM) rectifier has been one of the main power conversion topologies thanks to its full controllability. The key point in the dissertation is to study the DC power system consisting of a PMSG to be the main power input device and a PWM rectifier to be the main power conversion topology. The objective of control is to output a constant DC-link voltage in a wide PMSG speed range. Since the PM-excited flux linkage is constant, when the PMSG is working at a high speed, field-weakening is needed to stabilize the stator voltage, further to stabilize the DC-link voltage. Hybrid excitation may be used to realize the field-weakening, but it has complex structure; no auxiliary devices are needed in the field regulation with the armature current, and can be easily realized with the PWM recifier and field-regulation control strategies. In this dissertation, the typical applications of the DC power systems are first introduced, with a comprehensive analysis and elaboration on the relevant research throughout the world. The research work is focused on the DC power system and its stabilization control, which is composed of a PMSG and a PWM rectifier. The involved research content in this dissertation includes the following aspects: 1. DC power system design with a wide-speed-range PMSGAs for the common DC power systems, PMSG with high power density, high efficiency is selected to the system power input device, usually with a variable-speed prime mover. The PWM rectifier with fully controlled switches is chosen to be the power conversion topology, which converts the AC power generated by PMSG into DC power, and supplies the DC load after the DC filter. The matching between the system requirements and the generator parameters are determined. Through finite-element analysis (FEA), a PMSG with strong field-weakening ability and suitable for wide-speed-range operation has been designed and manufactured, and the system test bench has been built based on dSPACE. 2. Study, analysis, optimization and experimental verification of the traditional control strategiesAccording to the PMSG designed in part 1, the DC-link model has been built, as well as the control model of the traditional control strategies, e.g. field-oriented control (FOC), direct torque control (DTC), and the effectiveness of the DC-link voltage stabilization control has been verified in a wide speed range. The theory of active damping has been proposed and analyzed, and has been utilized in the DC-link voltage control. When the load on the DC-link changes, the dynamic response of the DC-link voltage has been greatly accelerated, and it recovers quickly to its reference value. In the meantime, the performance influence of the prime mover speed on the actual system test bench should be considered. Finally, the performance of FOC and DTC has been compared and analyzed. 3. Analysis and experimental verification of the direct voltage control (DVC), and the comparative study of all the studied control strategiesThe derivation process of DVC has been theoretically analyzed: the inner current loops in FOC have been eliminated to obtain the direct voltage field-oriented control (DVFOC); the reference value of d-axis voltage in DVFOC has been replaced by the product of the stator voltage calculated by the speed and the load condition, and the sine value of load angle generated by the DC-link voltage PI controller, in order to form the DVC-1. Further, the DC-link voltage PI controller directly outputs the reference value of load angle and it becomes DVC-2. Finally, the comparative study has been carried out among all the studied control strategies. / Doctorat en Sciences de l'ingénieur et technologie / info:eu-repo/semantics/nonPublished

The conversion of mechanical energy to electrical energy is done mainly with synchronous generators. They are used in hydropower generators and nuclear plants that presently account for about 80% of the electric energy production in Sweden. Because of the dominating role of the synchronous generators, it is important to minimize the power losses for efficient use of natural resources and for the economies of the electric power companies and their customers. For a synchronous machine, power loss means undesired heat production. In electric machines, there are power losses due to windage, friction in bearings, resistance in windings, remagnetization of ferromagnetic materials, and induced voltages in windings, shields and parts that are conductive but ideally should be non-conductive. The subject of this thesis is prediction of end region magnetic leakage fields in synchronous generators and the eddy current power losses they cause. The leakage fields also increase the hysteresis losses in the end regions. Magnetic flux that takes paths such that eddy current power losses increase in end regions of synchronous generators is considered to be leakage flux. Although only a small fraction of the total magnetic flux is end region leakage flux, it can cause hot spots, discoloration and reduce the service life of the insulation on the core laminations. If unattended, damaged insulation could lead to electric contact and eddy currents induced by the main flux between the outermost laminations. That gives further heating and deterioration of the insulation of laminations deeper into the core. In a severe case, the core can melt locally, cause a cavity, buckling and a short circuit of the main conductors. The whole stator may have to be replaced. However, the end region leakage flux primarily causes heating close to the main stator conductors which makes the damage possible to discover by visual inspection before it has become irrepairable.

A produção de energia elétrica por fontes de geração distribuída (GD) vem se tornando cada vez mais presente no sistema elétrico de potência. De modo geral, os sistemas de GD conectados à rede de distribuição operam controlando potências ativa e reativa, enquanto que no modo isolado, a frequência e a tensão. Sendo assim, após a ocorrência de um ilhamento deve haver alteração no modo de operação da GD para garantir a estabilidade da frequência e da tensão no subsistema ilhado. Ainda, se o modo de operação não for alterado após o ilhamento, os dispositivos de proteção podem atuar desligando a GD. Portanto, o tempo decorrido até a alteração do modo de operação desempenha um papel importante na indicação se a GD permanecerá ou não em funcionamento após a ocorrência do ilhamento. Neste trabalho, são determinados os tempos máximos para chaveamento dos modos de operação de um grupo motor gerador diesel (GMG) operando como GD, utilizando controladores clássicos (CCs) e controladores fuzzy (CFs). Foram analisadas as influências do desbalanço entre as potências geradas e consumidas, do tipo de carga conectada ao subsistema ilhado e do comprimento do alimentador nos tempos máximos. Para evidenciar possíveis vantagens da estratégia de controle não linear, é utilizada uma metodologia na qual o ajuste dos ganhos dos CFs é realizado a partir dos ajustes de referência dos CCs. Devido ao ganho variável que a estratégia não linear adiciona às ações de controle, a utilização de CFs nas malhas do GMG permitiu maiores tempos de chaveamento para determinadas faixas de operação, quando comparado com a utilização de CCs. / Distributed generation (DG) is becoming more present in the electrical power system. In general, when a DG is connected to the grid, the DG works with the active and reactive power control loops. Therefore, after an islanding occurrence, the DG must change the operation control mode from power control to voltage and frequency control to maintain the system stability. If the operation mode is not changed after islanding, the protective devices are sensitized and the DG is disconnected. Therefore, the time elapsed until the operation mode changes has an important role in the indication if the DG remains in operation or not after islanding. In this work, the maximum times for switching the operating control mode of a diesel generator set, working as a DG, are analysed using a classical control strategy (CC) and a fuzzy control strategy (FC). The influence of the power imbalance, load types and the feeder distance on the maximum available time to switch the operation control mode is investigated. To highlight the advantages of a nonlinear control strategy, is used a methodology in which the tuning of the FCs gains is performed from the CCs which are used as reference. Due to the variable gain added by the nonlinear strategy, the FC allowed higher switching times than the CC.

Esta tese propõe uma estratégia de controle fuzzy para um grupo motor gerador a diesel como uma fonte de geração distribuída, cobrindo a parte mecânica do sistema que é composta por controle de velocidade e de potência ativa, a parte elétrica do sistema composta por controle de tensão e potência reativa, e também o controle de sincronismo com a rede de distribuição. A estratégia de controle foi baseada em lógica fuzzy que usou uma superfície de controle fixa para os controladores fuzzy. Foram investigados os distúrbios causados pelo efeito de conexão com a rede e da conexão de um motor de indução, um retificador não controlado e uma carga RLC. Resultados de simulação para fluxo de potência no modo conectado foram obtidos usando um alimentador padrão IEEE -1547. Os resultados de simulação obtidos para os modos isolado e conectado usando o controlador fuzzy foram superiores comparados aos resultados obtidos com um controlador comercial. Uma bancada experimental também foi usada para analisar a resposta do sistema no modo isolado com o controlador fuzzy proposto e com o controlador comercial para fins de comparação. Nesse contexto, espera-se com este trabalho contribuir para o desenvolvimento de pesquisas na área de controle e processamento de energia, uma vez que, soluções para a produção de energia utilizando a geração distribuída têm importância estratégica e têm sido foco de investimento e discussões por parte de governos, empresas e universidades. / This thesis proposes a control strategy for a diesel generating set as a distributed generation source covering the mechanical part of the system which includes speed and active power control, the electrical part of the system which includes voltage and reactive power control, and also the synchronism control with the grid. The control strategy was based on a fuzzy logic which used a fixed controller surface for the fuzzy controllers. The effect of the disturbances caused by the grid connection and the disturbances caused by the activation of a induction motor, non controled rectifier and a RLC load types were investigated. Power flow simulation results for the grid-connected mode was obtained with a IEEE -1547 standard feeder. The simulations results for both stand-alone and gridconnected operations using fuzzy controllers were superior when compared to commercial methods. An experimental setup was also used to analyze the system responses under isolated mode with the proposed fuzzy controller and with the commercial controllers for comparison proposes. In this context, it is expected that this work contributes to the development of control and energy processing research area, since solutions for energy production using distributed generation have strategic importance and have been the focus of investment and discussions from governments, companies and universities.

This works applies the idea of adjustment an engine-generator, so it is possible to connect an engine-generator, or other type of a generator, to the electricity. Consequently, the machine can transform the power supply without an outage. This work concerns the complex approach, provides the descriptions of particular parts, sensors and active components of a motor-generator and includes the explanation of their function. Further research is focused on designing and drawing a plan with a choice of a control unit for the whole system. Finally, the work deals with the complex implementation and testing the machine in real operation.

Parametry nahradniho obvodu synchronniho stroje znance ovlivnuji jeho chovani jak pri statickem provozu, tak predevsim pri nahlych dynamickych jevech a poruchovych stavech. Prace je zamerena na zhodnoceni dostupnych metod pro vypocet techto parametru pomoci Metody konecnych prvku. Prvni cast je venovana teoretickemu popisu zakladnich principu Metody Konecnych Prvku a jejich aplikaci na reseni problemu elektromagnetickeho pole v elektrickych strojich. Zaroven take shrnuje zakladni usporadani nahradniho obvodu synchroniho stroje, principi jeho konstrukce a zakladni funkci. Druha cast je venovana praktickemu vypoctu reaktanci nahradniho obvodu synchronniho stroje. S pomoci MKP jsou vypocteny synchronni reactance s uvazovanim vzajmeneho magnetickeho pusobeni proudu v d a q ose. Pro vypocet transientnich a subtransientnich reaktanci jsou navrzeny ctyri odlisne metody a jsou zhodnoceny z hlediska pozadovane presnosti vypoctu a narocnosti na vypocetni cas. Zaverecna cast popisuje zakladni merici metody pro urceni parametru nahrandniho obvodu na skutecnem stroji. Kapitola take obsahuje srovnani simulace trifazoveho zkratu synchronniho stroje s realnou zkouskou provedenou laboratorne. Zaver obsahuje srovnani jednotlivych metod a navrh optimalniho postupu pro vypocet zkoumanych parametru.