Hot sections of gas engine turbines require specialized materials to withstand extreme conditions present during engine operation. Nickel-base superalloys are typically used as blades and disks in the high pressure turbine section because they possess excellent fatigue strength, creep strength and corrosion resistance at elevated temperatures. Components undergo thermomechanical fatigue conditions as a result of transient engine operation. Sharp geometric features, such as cooling holes in blades or fir-tree connections in disks, act as local stress raisers. The material surrounding these features are potential sites of localized inelastic deformation and crack formation. To reduce customer costs associated with unnecessary overhauls or engine down-time, gas turbine manufacturers require accurate prediction methods to determine component endurances. The influence of stress concentration severity on thermomechanical fatigue crack formation is of particular importance as cracks often initiate in these hot spots. Circumferentially notched specimens were utilized to perform thermomechanical fatigue experiments on blade material CM247LC DS and disk material PM IN100. A parametric study on CM247LC DS was performed utilizing four notched specimens. Experimental results were coupled with finite element simulations utilizing continuum based constitutive models. The effects of applied boundary conditions on crack initiation life was studied in both alloys by performing experiments under remotely applied force and displacement boundary conditions. Finite element results were utilized to develop a life prediction method for notched components under thermomechanical fatigue conditions.

La majeure partie des équipements électroniques qui nous entourent fonctionne dans des environnements plutôt cléments où les variations thermiques sont d’amplitudes faibles à modérées. En aéronautique, l’utilisation d’équipements fonctionnant dans des milieux beaucoup plus hostiles que les environnements traditionnellement rencontrés en électronique pourrait permettre d’améliorer considérablement les performances des aéronefs, notamment en terme de poids, de consommation de carburant et de coût de maintenance. Toutefois, l’utilisation d’assemblages électroniques « classiques » dans des environnements où les variations thermiques sont fortes pose des problèmes techniques majeurs : les hautes températures peuvent faire fondre les alliages de brasure courants et la fatigue thermomécanique peut très rapidement provoquer la défaillance des assemblages. Pour pallier ces problèmes, les composants électroniques peuvent être reportés par frittage d’argent dans les circuits. En effet, cette technologie d’assemblage permet de remplacer les brasures usuelles par un matériau ayant un point de fusion nettement plus élevé : l’argent pur (Tfus=962°C). Cependant, le frittage a tendance à produire des matériaux poreux et la porosité peut avoir un effet néfaste sur le vieillissement des joints d’attache des composants électroniques. Par conséquent, dans cette thèse, les liens existant entre profil thermique de frittage et porosité ainsi que ceux existant entre porosité et résistance aux cycles thermiques (-65°C/+200°C) ont été étudiés. Par ailleurs, la question des interactions métallurgiques pouvant se produire à hautes températures entre l’argent fritté et certaines métallisations usuelles de composants et de substrats a également été abordée. / Most of usual electronic devices operate in environments where the amplitude of temperature changes is limited. The use of electronic equipment operating in harsh environments in aircrafts could however improve their performances, especially their weight, their gas consumption and their cost of maintenance. Unfortunately the use of classical electronic assembly technologies in environments where wide amplitude thermal variations take place raises major technical issues: the high temperatures reached in some parts of aircrafts can melt usual brazing materials and thermomechanical fatigue can induce early failure of the assemblies. To prevent these problems from happening, electronic components can be attached using silver sintering. One of the strengths of this technology is that it allows the replacement of traditional brazing material by a high melting point material: pure silver (Tm=962°C). Silver sintering nevertheless leads to a porous material and porosity can have a negative impact on the ageing of the attachment joints of electronic components. One of the goals of this PhD thesis is therefore to study the link between the sintering temperature profile and the porosity of silver. Furthermore the impact of different rates of porosity on the mechanical behavior of silver has been assessed. These investigations have mainly been focused on the fatigue behavior of porous silver electrical junctions under thermal cycling (-65°C/+200 °C). The question of the metallurgical interactions that may exist at high temperatures between silver and some of the usual metallization of components and/or substrates has lastly been addressed.

Gradientes térmicos induzidos no interior de componentes sujeitos a variações de temperatura durante o período de funcionamento podem provocar a ocorrência de tensões e deformações internas. A repetição destes ciclos térmicos pode causar a nucleação e a propagação de trincas por um processo denominado fadiga termomecânica. Este trabalho apresenta um estudo sobre o comportamento da liga de alumínio A356-T6, processada nas condições fundida e tixoextrudada, sob fadiga isotérmica e termomecânica. Foram realizados ensaios de fadiga de baixo ciclo isotérmica para as temperaturas de 120 e 280°C, e ensaios de fadiga termomecânica em-fase e fora-de-fase para a faixa de temperatura de 120 a 280°C. O material tixoextrudado apresentou melhor desempenho em fadiga nas condições isotérmica e anisotérmica (termomecânica) devido a uma microestrutura globular com menor nível de porosidade. / Thermal gradients induced in components during service under temperature changes can cause internal stresses and strains. This cyclic thermal behavior can cause crack nucleation and propagation under a process denominated thermomechanical fatigue. Permanent mold casting and tixoextruded A356-T6 aluminum alloy behavior under isothermal and thermomechanical fatigue was study in this work. Isothermal low cycle fatigue tests were performed in temperatures of 120 and 280°C. In-phase and out-of-phase thermomechanical fatigue tests were carried out in temperature range from 120 to 280°C. The tixoextruded material presented better isothermal and thermomechanical fatigue performance due to a globular microstructure and lower porosity level.

This research establishes a physics-based life determination model for the second generation single crystal superalloy PWA 1484 experiencing out-of-phase thermomechanical fatigue (TMF). The life model was developed as a result of a combination of critical mechanical tests, dominant damage characterization and utilization of well-established literature. The resulting life model improves life prediction over currently employed methods and provides for extrapolation into yet unutilized operating regimes. Particularly, the proposed deformation model accounts for the materials' coupled fatigue-environment-microstructure response to TMF loading. Because the proposed model is be based upon the underlying deformation physics, the model is robust enough to be easily modified for other single crystal superalloys having similar microstructure. Future use of this model for turbine life estimation calculations would be based upon the actual deformation experienced by the turbine blade, thereby enabling turbine maintenance scheduling based upon on a "retirement for a cause" life management scheme rather than the currently employed "safe-life" calculations. This advancement has the ability to greatly reduce maintenance costs to the turbine end-user since turbine blades would be removed from service for practical and justifiable reasons. Additionally this work will enable a rethinking of the warranty period, thereby decreasing warranty related replacements. Finally, this research provides a more thorough understanding of the deformation mechanisms present in loading situations that combine fatigue-environment-microstructure effects.

Le matériau étudié est un alliage Al A356, utilisés pour produire des têtes de cylindres pour l'industrie automobile par fonderie. Le matériau présente une microstructure dendritique assez grossière dans une matrice eutectique, avec une taille moyenne de grains de 25 microns, des précipités intermetalliques et des porosités. Les propriétés de traction sont fortement affectées par la température d'essai, avec une baisse assez sensible du module de Young, de la limite d'élasticité lorsque la température augmente. La durée de vie de fatigue isotherme chute de façon marquée (approximativement d'un facteur 10) lorsque la température d'essai est portée de 120 à 280 °C, en déformation imposée. Du essais thermomecaniques cycliques en phase, avec une température variant de 120 à 280 °C, on montré que la durée de vie en anisotherme est assez similaire à celle obtenue en conditions isothermes à 280 oC. Dans ce cas, les dommages causés par le chargement thermomécanique cyclique se produisent à la température la plus élevée du cycle. Les essais de relaxation ont montré l'existence de deux comportements distincts. À basse température, le matériau présente de l'écrouissage cyclique tandis qu'il s'adoucit cycliquement à des températures plus élevées. A partir des résultats de croissance des fissures de fatigue, on a observé que la température et la forme du cycle de fatigue a une forte influence sur la vitesse de fissuration par fatigue ainsi que sur le facteur d'intensité des contraintes seuil. Une loi de comportement élastique visco-plastique non-isotherme a été identifiée pour le matériau. Les paramètres de comportement mécanique sont statistiquement distribués du fait de la fabrication du matériau par fonderie. Toutefois, il a été démontré que le modèle était capable de se reproduire, avec une approximation raisonnable, les essais contrainte-déformation à des températures différentes, pour le cas isotherme et anisotherme. / The studied material is an A356 Al alloy, used to produce engine cylinder heads for the automotive industry by die casting process. The material displays a quite coarse dendritic microstructure in a eutectic matrix, with a mean grains size of 25 microns, intemetallic precipitates and porosities. The tensile properties are strongly affected by testing temperature, with a quite sensitive drop of the Young's modulus, the Yield stress as the temperature was raised. The isothermal fatigue life dropped of markedly (approximately 10 times) when the testing temperature is raised from 120 to 280 °C, under strain control. From the themomechanical in-phase cyclic tests, with temperature varying from (120 to 280 oC), it was possible to observe that life is quite similar to the isothermal fatigue test at 280 oC. In this case, the more sensitive damage caused the in-phase mechanical and thermal cycle take place at the highest temperature. Relaxation tests indicated two distinct behaviors, with the temperature of 240°C being a threshold. At lower temperatures, the material hardens cyclically whereas it softens cyclically at higher temperatures. From the fatigue crack growth results, it was observed that temperature and wave shape has a strong influence on the crack growth rate as well as on the stress intensity threshold. Considering sinusoidal wave shape (10 Hz), as the temperature increased the DKth decreased and the crack propagation rate increased. However, the rate as da/dN change with temperature is quite similar, as an indicative that the micromechanism of crack growth has not changed due to the high frequency used, and it was due only to loss of mechanical strength. An elastic-visco-plastic non-isothermal constitutive law was identified for the material. For the cast material studied in this work, the mechanical behavior parameters are statistically distributed. However, it was shown that the model was able to reproduce, with a reasonable approximation, the stress – strain relationship at different temperatures, for the isothermal and anisothermal cases. / Para caracterizar componentes usados em aplicações de alta responsabilidade não basta apenas conhecer a composição química e os resultados de ensaios de tração, impacto e dureza, pois estes podem não fornecer os subsídios necessários que permitam prever, de maneira confiável, o comportamento dos componentes nas condições reais de trabalho. Exemplo disto são os cabeçotes de motor automotivos, submetidos a tensões térmicas e mecânicasrelativamente altas durante seu uso normal e altíssimo em condições extremas. Durante longos tempos de funcionamento e eventuais falhas na refrigeração e ou lubrificação a temperatura pode chegar a valores próximos de 300ºC. Esta variação de temperaturas provoca choques térmicos que podem gerar trincas e/ou uma grande quantidade de deformação plástica em regiões próximas aos pistões. Desconsiderando a presença de choques térmicos provocadospor falhas, ainda assim, uma pequena quantidade de ciclos de acionamento e parada do motor, é considerada como os principais causadores de pequenas trincas. Isso indica que o surgimento de trincas em cabeçotes de motor deve ser considerado um problema de fadiga termomecânica de baixo ciclo. Outro problema é a heterogeneidade microestrutural no componente devido ao processo de fundição, levando a propriedades mecânicas e físicas diferentes em uma mesma peça. Além da presença de porosidade gerada por bolhas de gás e vazios de solidificação, que podem adquirir tamanho tal que se aproximem de pequenas trincas, diminuindo a vida para a nucleação e assim mudando o foco do problema para o de propagação de trinca por fadiga. A proposta deste trabalho foi a de determinar as propriedades de fadiga isotérmica e termomecânica através de ensaios de fadiga de baixo ciclo, bem como as propriedades de propagação de trinca por fadiga, relaxação, caracterização microestrutural e modelagem do comportamento mecânico por elementos finitos para a liga de alumínio utilizada na fabricação de cabeçotes de motores automotivos pela indústria nacional. Todos os ensaios e análises computacionais foram realizados nos laboratórios da Universidade de São Paulo (EESC-USP) e da École Normale Supérieure de Cachan (ENS-LMT). Os ensaios de fadiga isotérmica foram realizados nas temperaturas de 120ºC e 280ºC e os ensaios termomecânicos foram realizados em fase entre as temperaturas de 120ºC e 280ºC. Os ensaios de relaxação foram realizados em várias temperaturas com carregamento de onda trapezoidal, enquanto que os ensaios de propagação de trinca por fadiga foram realizados nas temperaturas de 120ºC, 200ºC e 280ºC para arregamentos de onda senoidal e trapezoidal em controle de carga e de deslocamento. Foi feita também análise microestrutural nos corpos de prova, após os ensaios de fadiga, por microscopia óptica e por microscopia eletrônica de varredura MEV.Os resultados destes ensaios mostraram que os defeitos de fundição e a falta de homogeneidade no material, aliados a longos tempos de exposição a carregamentos e em altas temperaturas, constituem um fator crítico no desempenho do componente. Estes resultados ajudarão a estabelecer modelos precisos de previsão de vida para os cabeçotes de motor.

Gradientes térmicos induzidos no interior de componentes sujeitos a variações de temperatura durante o período de funcionamento podem provocar a ocorrência de tensões e deformações internas. A repetição destes ciclos térmicos pode causar a nucleação e a propagação de trincas por um processo denominado fadiga termomecânica. Este trabalho apresenta um estudo sobre o comportamento da liga de alumínio A356-T6, processada nas condições fundida e tixoextrudada, sob fadiga isotérmica e termomecânica. Foram realizados ensaios de fadiga de baixo ciclo isotérmica para as temperaturas de 120 e 280°C, e ensaios de fadiga termomecânica em-fase e fora-de-fase para a faixa de temperatura de 120 a 280°C. O material tixoextrudado apresentou melhor desempenho em fadiga nas condições isotérmica e anisotérmica (termomecânica) devido a uma microestrutura globular com menor nível de porosidade. / Thermal gradients induced in components during service under temperature changes can cause internal stresses and strains. This cyclic thermal behavior can cause crack nucleation and propagation under a process denominated thermomechanical fatigue. Permanent mold casting and tixoextruded A356-T6 aluminum alloy behavior under isothermal and thermomechanical fatigue was study in this work. Isothermal low cycle fatigue tests were performed in temperatures of 120 and 280°C. In-phase and out-of-phase thermomechanical fatigue tests were carried out in temperature range from 120 to 280°C. The tixoextruded material presented better isothermal and thermomechanical fatigue performance due to a globular microstructure and lower porosity level.

Yttria-stabilized zirconia-based thermal barrier coating systems are the most widely used commercial coatings in the industry, with practical applications in aircraft engines and land-based power turbines. The purpose of thermal barriers is primarily to protect the substrate from high temperatures and also to increase its oxidation resistance. Currently, concerning the relatively frequent volcanic eruptions and increasing air traffic intensity in desert areas, increased attention is being paid to the development of new thermal and environmental coatings that will withstand the so-called CMAS attack and still successfully meeting the strictest requirements of the aerospace industry. Two newly developed experimental coatings consisting of three successive layers have been developed for this work. The upper two layers are thermal insulating ceramic coatings, where two different uppermost coatings were deposited. The first uppermost layer of the coating is a mixture of mullite and hexacelsian in a ratio of 70/30 wt. %. The second upper most type of coating consists of Al6Si2O13 + MgAl2O4 + BaCO3 in a ratio of 6:3:1 wt. %. The interlayer is made of the commercially utilized yttria-stabilized zirconia. The metallic CoNiCrAlY coating, which is directly deposited on the nickel-based superalloy MAR-M247, fulfils a compensatory function between the mechanical properties of the nickel superalloy and the ceramic coating. The thermal and environmental barrier system was deposited using air plasma spraying (APS) technology. The main objective of this work was to evaluate the effect of the newly developed thermal and environmental barrier coating, which has a high potential for the protection of component surfaces in an aggressive environment, on isothermical and thermomechanical fatigue behaviour of nickel-based superalloy MAR-M247. Low cycle fatigue tests were performed in strain control mode with constant strain amplitude on both uncoated and TEBC coated superalloy. Fatigue hardening/softening curves, cyclic stress-strain curves and fatigue life curves in the representation of total strain amplitude, plastic strain amplitude and stress amplitude on the number of cycles to failure were obtained. Microstructural analysis of MAR-M247 superalloy and a newly developed experimental coating was performed in a scanning electron microscope. The fatigue crack initiation sites were identified and the process of fatigue crack propagation was described. The dislocation arrangement after fatigue loading of MAR-M247 was investigated in a transmission electron microscope. The findings of isothermical and thermomechanical low cycle fatigue behaviour of uncoated and TEBC coated MAR-M247 superalloy and identification of damage mechanisms presented in this dissertation will improve the estimation of safe-life that is particularly relevant to aircraft engines components.

Superaustenitická korozivzdorná ocel typu 22Cr25NiWCoCu určená pro vysokoteplotní aplikace v energetickém průmyslu byla studována za podmínek nízkocyklové únavy při pokojové a zvýšené teplotě. Jednotlivé vzorky byly podrobeny různým zátěžným procedurám, což umožnilo studium materiálové odezvy spolu s mechanismem poškození. Křivky cyklického zpevnění/změkčení, cyklického napětí a Coffin-Mansonovy křivky byly vyhodnoceny. Únavová životnost materiálu byla diskutována s ohledem na uplatňované mechanismy poškození, které se vyvinuly za specifických zátěžných podmínek. Standardní izotermální únavové experimenty byly provedeny při pokojové a zvýšené teplotě. Hysterezní smyčky zaznamenané během cyklického zatěžování byly analyzovány pomocí zobecněné statistické teorie hysterezní smyčky. Pro různé amplitudy napětí byla určena jak distribuce hustoty pravděpodobnosti interních kritických napětí (dále PDF), tak rovněž zjištěn její vývoj během cyklického namáhání. Zjištěné průběhy PDF byly korelovány s vývojem povrchového reliéfu a vnitřního dislokačního uspořádání zdokumentované pro obě teploty pomocí rastrovací elektronové mikroskopie (SEM) vybavené technikou fokusovaného iontového svazku (FIB), která umožnila rovněž efektivní studium nukleace povrchových únavových trhlin. Při cyklickém zatížení při pokojové teplotě byla pozorována lokalizace cyklické plastické deformace do perzistentních skluzových pásů (PSP). V místech, kde tyto PSP vystupují na povrch materiálu byly pozorovány perzistentní skluzové stopy (PSS) tvořené extruzemi a intruzemi. Postupné prohlubování intruzí, zejména na čele nejhlubší intruze, vede k iniciaci únavové trhliny. Odlišný mechanismus tvorby trhlin byl zjištěn při únavové zkoušce při zvýšené teplotě, kde zásadní roli hrál vliv prostředí. Rychlá oxidace hranic zrn a jejich následné popraskání představuje dominantní mechanismus v I. stádiu nukleace trhlin. Aplikace desetiminutové prodlevy v tahové části zátěžného cyklu vedlo k vývoji vnitřního (kavitačního) poškozování. Mechanismy vnitřního poškozování byly studovány na podélných řezech rovnoběžných s napěťovou osou zkušebních vzorků. Trhliny a jejich vztah k hranicím zrn a dvojčat byly studovány pomocí difrakce zpětně odražených elektronů (EBSD). Vliv prodlevy na únavovou životnost byl korelován s vývojem povrchového reliéfu a vnitřního poškození. Vzorky z uvedené oceli byly rovněž podrobeny zkouškám termomechanické únavy (TMF), při nichž se v čase mění jak zátěžná síla tak i teplota. Termomechanické únavové zkoušky v režimu soufázném (in-phase) a protifázném (out-of-phase) byly provedeny jak s prodlevou, tak i bez ní. Ve všech případech bylo pozorováno rychlé cyklické zpevnění bez ohledu na použitou amplitudu deformace, u vzorků testovaných v out-of-phase režimu byla zjištěna tendence k saturaci. Zkoumáním povrchového reliéfu za pomocí technik SEM a FIB byla odhalena přednostní oxidace hranic zrn a následné praskání těchto hranic kolmo k ose zatížení. Prodlevy v cyklech při maximálním napětí vedly ke zvýšení amplitudy plastické deformace a následně ke creepovému poškození ve formě vnitřních kavit a trhlin. Interkrystalické šíření trhlin bylo pozorováno na vzorcích testovaných v režimu in-phase. Vývoj poškození v režimu out-of-phase nebyl principiálně ovlivněn zařazením prodlevy do zátěžného cyklu. Charakteristickým znakem namáhání v režimu out-of-phase je nukleace několika trhlin v homogenní oxidické vrstvě jdoucích napříč zrny kolmo k ose zatěžování.