Thin film silicon on low temperature glass substrates is currently seen as the best path toreduce the $/W cost of photovoltaic (PV) modules. However, producing thin film polysilicon, on glass, is an ongoing research challenge. Laser crystallisation of a-Si is one of the possible methods. Typically excimer (XMR) lasers are used for laser crystallisation. This thesis introduces the copper vapour laser (CVL) as a viable alternative for thin film photovoltaic applications. The CVL, like the XMR, is a high powered, pulsed laser. However, the CVL has higher pulse rates (4-20kHz), better beam quality and a visible wavelength output (578 & 511nm). Preliminary experiments, using 600K-heated silicon-on-quartz samples, confirmed that CVL crystallisation can produce area weighted average grain size of 0.1-0.15??m, which is comparable to results reported for XMR??? s. Importantly, the CVL results used thicker films (1??m), which is more applicable to thin photovoltaic devices that need 1-10??m of silicon to be viable. The CVL??? s longer wavelength and therefore longer penetration depth (1/alpha) are proffered as the main reason for this result. Extensive laser-thermal modelling highlighted further opportunities specific to CVL crystallisation. Through-the-glass doublesided irradiation was shown in simulations to reduce thermal gradients, which would enhance crystal growth. The simulations also produced deeper melts at lower surface temperatures, reducing the thermal stress on the sample. Subsequent experiments, using silicon-on-glass, confirmed the benefit of through-the-glass doublesided irradiation by maintaining grain sizes without the usual need for substrate heating. Furthermore, Raman analysis showed that doublesided crystallisation achieved full depth crystallisation, unlike single side irradiation which produced partial crystallisation. A new mode of crystallisation, stepwise crystallisation, was also postulated whereby a series of CVL pulses could be used to incrementally increase the crystallisation depth into the silicon. Simulations confirmed the theoretical basis of the concept, with HeNe Raman spectroscopy and analysis of surface grain sizes providing indirect experimental support. The CVL??? s ability to crystallise thicker films more directly applicable to photovoltaic devices secures its viability as an alternative laser for photovoltaic applications. The through-the-glass doublesided irradiation and the stepwise crystallisation provide additional potential for increased process flexibility over XMR???s.

One of the poly-Si thin-film cells developed at the University of New South Wales (UNSW) is the EVA cell. In this work, SiN films for EVA cells as an antireflection/barrier coating were investigated. In addition, the effect of hydrogenation pre-treatment of solid phase crystallisation (SPC) on grain size and open-circuit voltage (Voc) was investigated. The SiN films deposited by PECVD were examined for uniformity of the thickness and the refractive index of the films across the position of the samples in the PECVD deposition system. A spectrophotometric analysis was used to determine these film properties. It was found that these properties were very uniform over the deposition area. Good repeatability of the depositions was also observed. A series of SiN film depositions by reactive sputtering were also performed to optimize the deposition process. Parameters adjusted during the deposition were nitrogen flow rate, substrate bias, and substrate temperature. By investigating the deposition rate, refractive index, and surface roughness of the films, the three deposition parameters were optimised. The effects of post SiN deposition treatments (a-Si deposition, SPC, RTA, and hydrogenation) on thickness and refractive index of both SiN films deposited by PECVD and reactive sputtering were investigated by using samples which have the same structure as the EVA cells. The thickness of the PECVD SiN films decreased about 6 % after all the treatments. On the other hand, the thickness reductions of the reactively sputtered SiN films were very small. The refractive index of the PECVD SiN films increased about 0.6 % after the treatments, whereas that of the reactively sputtered SiN films decreased 1.3 % after the treatments. As a possible method to improve the performance of EVA cells, hydrogenation of a-Si was investigated as a pre-treatment of SPC process. There were no obvious differences in the grainsize and the Voc of the EVA cells with and without the hydrogenation. Therefore it is likely that the hydrogenation pre-treatment of SPC does not have a beneficial effect on the performance of EVA cells.

The cost of photovoltaic electricity needs to be significantly reduced in order to achieve a high electricity market penetration. Thin-film solar cells have good potential to achieve such cost savings though (i) large-area deposition onto low-cost foreign substrates, (ii) more streamlined processing, (iii) monolithic cell interconnection, and very efficient use of the expensive semiconductor material. Polycrystalline silicon (poly-Si) on glass is a promising technology for the cost-effective large volume production of PV modules since it (i) makes use of an abundant raw material, (ii) is non-toxic, (iii) does not suffer from light-induced degradation, and (iv) does not rely on TCO layers. Usually plasma enhanced chemical vapour deposition (PECVD) is used for the layer formation. This thesis explores the use of e-beam evaporation as deposition method since it is potentially much faster and cheaper than PECVD. The resulting solar cells are referred to as EVA (from EVAporation). Two inherent shunting mechanisms in EVA cells are demonstrated to be shunting through sub-micron sized pinholes when the back electrode is deposited and shunting between the emitter and the absorber layer at the glass-side electrode. Through the improved understanding of these shunting mechanisms it was possible to develop a suitable metallisation scheme for EVA cells using an aligned deposition of emitter and back surface field line contacts and a specially developed shunt mitigation etching technique. For the first time appreciable efficiencies of up to 5.2% were demonstrated on this material. It was also shown that only very lightly doped absorber layers can lead to the required high short-circuit currents in EVA cells. The resulting cells are currently completely limited by space charge region recombination occurring with comparatively low ideality factors of only ~ 1.4 This thesis also demonstrates the usefulness of Jsc-Suns measurements and investigates optical loss mechanisms in the current devices. Advanced modelling of distributed series resistance effects, influencing Suns-Voc, m-Voc and Jsc-Suns curves, is employed. PC1D modelling is used to extract relevant device parameters. In this work it was found that the diffusion length in the best EVA cells is longer than the absorber layer and that insufficient light trapping is currently the major hurdle to higher cell efficiencies. From the obtained results it can be concluded that EVA solar cells are promising candidates for the low-cost and high-volume production of solar modules.

Thesis (M.S.)--Rochester Institute of Technology, 1989. / "References": leaves 20-23.

Thesis (M.S.)--Oregon State University, 2009. / Printout. Includes bibliographical references (leaves 145-153). Also available on the World Wide Web.

Thesis (M.S.)--Oregon State University, 2009. / Printout. Includes bibliographical references (leaves 78-82). Also available on the World Wide Web.

Thesis (Ph. D.)--University of California, San Diego, 1999. / Vita. Includes bibliographical references.

Thesis (M.S.)--Boise State University, 2009. / Includes abstract. Includes bibliographical references (leaves 124-131).

Thesis (Ph. D.)--Mechanical Engineering, Georgia Institute of Technology, 2009. / Committee Chair: Sitaraman, Suresh; Committee Member: Degertekin, Levent; Committee Member: McDowell, David; Committee Member: Tummala, Rao; Committee Member: Vandentop, Gilroy; Committee Member: Wang, Zhong Lin. Part of the SMARTech Electronic Thesis and Dissertation Collection.

Thesis (M.Sc.)--Memorial University of Newfoundland, 2006. / Bibliography: leaves 83-91. Also available online.