No description available.

Noise contribution in nonlinear systems is very different from that in linear systems. The noise effects in nonlinear systems can be complicated and not obvious to predict. In this thesis, the focus was on the noise contribution in nonlinear systems when measuring with the nonlinear vector network analyzer (NVNA). An additional noise source together with a single sinewave signal was fed into the input of the amplifier and the performance was studied. The input power of the amplifier is considered to be the sum of the noise power and the signal power. The variation of the 1 dB compression point and the third order interception point as functions of the added noise power were studied. From the measured results in this thesis, the 1 dB compression point referred to the output power will decrease when increasing the added noise power at the input of the amplifier. The contribution of the added noise to the 1 dB compression point of an amplifier is considered dual: with the added noise the linear regression lines of the AM/AM curves are changed, and due to hard clipping the useful output power is reduced. As a result of those two effects, the added noise made the compression start at a lower power level. When the added noise reaches a certain level, the 1 dB compression point is hard to measure. Thus when performing nonlinear measurements, the noise effects should be taken into considerations and further studies are required to get better understanding of the system’s behavior in noisy environment.

This thesis describes possibilities of measuring permittivity of various materials, especially with coaxial probe method. It describes character of measuring method, hardware requirements and how to calculate values from the measured. Objective of this thesis is to design measuring station for measuring permittivity of materials with coaxial probe including calibration set. Code in Matlab is also programmed and whole station is tested with known samples to discuss measurement accuracy.

In biomedical applications realistic phantoms are becoming more useful for validation and testing of precursor systems. These artificial phantoms require stable and flexible tissue-mimicking materials with realistic dielectric properties in order to properly model human tissues. We have fabricated a low-water-content, low cost, mechanically and electrically stable, good shelf life and multi-layered heterogeneous phantom consisting of skin, fat and muscle tissues. We have chosen semi-solid type phantom for each tissue layer. The size and thickness of the each layer is chosen based on the average thickness of human tissue. Altering the ingredient composition wisely we can alter its dielectric properties also. By reason of no osmosis occurrence, the tissues can be employed to construct heterogeneous phantoms or even anthropomorphic phantoms without causing any changes in geometry or electrical properties. The performance of the fabricated phantom is carried out using an open-ended coaxial slim probe system by Agilent Technologies. Nearly all previous studies were based on very high frequency( VHF), so we present ultra-wide band (UWB), 500MHz-20GHz multilayered phantoms. We have measured our phantom after 2 month time period and we got quite good results for the dielectric properties without having significant variations. Thus, our fabricated sets of ATE phantom have good long lasting properties with good physical and dielectric stability.

Объектом исследования является дискретный фазовращатель ДМВ диапазона. Цель работы - разработка фазовращателя с требуемыми в техническом задании параметрами. В процессе работы был рассчитан и смоделирован фазовращатель в среде проектирования «АWR Design Environment», разработана электрическая принципиальная схема и перечень элементов, создан макет устройства и проведены его измерения. Моделирование ФВ проводилось с применением методов электромагнитного анализа и использованием в качестве основных активных элементов их S-параметров и Spice-моделей. В результате проведенной работы был создан макет фазовращателя с требуемыми параметрами. Результаты работы будут применены при создании фазированной антенной решетки метеорологического радиолокатора. / The object of the research is a discrete phase shifter of the UHF range. The purpose of the work is to develop a phase shifter with the parameters required in the technical specification. In the process of work, the phase shifter was calculated and modeled in the AWR Design Environment, an electrical schematic diagram and a list of elements were developed, a device model was created and its measurements were carried out. PV modeling was carried out using the methods of electromagnetic analysis and using their S-parameters and Spice-models as the main active elements. As a result of the work carried out, a prototype of a phase shifter with the required parameters was created. The results of the work will be used to create a phased array of a meteorological radar.

Abstract This dissertation presents complete parameterizations for a three-dimensional (3-D) geometry-based stochastic radio channel model (GSCM) at 10 GHz based on measurement campaigns. The thesis is divided into the following main parts: radio channel measurements, the characterization of model parameters, and model validation. Experimental multiple-input multiple-output (MIMO) channel measurements carried out in two-story lobby and urban small cell scenarios are first described. The measurements were performed with a vector network analyzer and dual polarized virtual antenna arrays with a bandwidth over 500 MHz. The measurement data was post-processed using the ESPRIT algorithm and the post-processed data was verified using a semi-deterministic map-based model. The results showed a good match between estimated and modeled multipath components (MPCs). In addition, single-input single-output outdoor-to-indoor measurements were executed through a standard multi-pane glass window and concrete wall. A statistical analysis was carried out for defining full 3-D characterization of the propagation channel in both line-of-sight (LOS) and non-line-of-sight (NLOS) propagation conditions. The delay and angular dispersions of MPCs are smaller in comparison to lower frequency bands due to the higher attenuation of the delayed MPCs. Moreover, specular reflection is observed to be the more dominant propagation mechanism in comparison to diffuse scattering, leading to smaller cluster angle spreads in comparison to lower frequency bands. The penetration loss caused by a standard multi-pane glass window is on the same level as in the lower frequency bands, whereas the loss caused by the concrete wall is a few dBs higher than at lower frequency bands. Finally, the GSCM with determined parameters is validated. A MIMO channel was reconstructed by embedding 3-D radiation patterns of the antennas into the propagation path estimates. Equivalently the channel simulations were performed with a quasi deterministic radio channel generator (QuaDRiGa) using the defined parameters. The channel capacity, Demmel condition number, and relative condition numbers are used as the comparison metrics between reconstructed and modeled channels. The results show that the reconstructed MIMO channel matches the simulated MIMO channel well. / Tiivistelmä Tämä väitöskirja esittää parametroinnit kolmiulotteiselle geometriaan perustuvalle stokastiselle radiokanavamallille 10 GHz:n taajuusalueella perustuen mitattuun radiokanavaan. Väitöskirja koostuu kolmesta pääalueesta: radiokanavamittaukset, radiokanavamallin parametrien määrittäminen ja mallin validointi. Aluksi kuvataan kaksikerroksisessa aula ja kaupunkipiensolu ympäristöissä monilähetin monivastaanotin (MIMO) järjestelmällä tehdyt kanavamittaukset. Mittaukset tehtiin vektoripiirianalysaattorilla ja kaksoispolaroiduilla virtuaaliantenniryhmillä 500 MHz kaistanleveydellä. Mittausdata jälkikäsiteltiin käyttämällä ESPRIT-algoritmia ja jälkikäsitelty data varmennettiin osittain deterministisellä mittausympäristön karttaan pohjautuvalla radiokanavamallilla. Tulokset osoittivat hyvän yhteensopivuuden mitattujen ja mallinnettujen moniteiden välillä. Lisäksi toteuttiin yksi-lähetin yksi-vastaanotin mittaukset ulko-sisä etenemisympäristössä monikerroksisen lasin ja betoniseinän läpi. Tilastollinen analyysin avulla määritettiin täysi kolmiulotteinen kuvaus radioaallon etenemiskanavasta näköyhteys ja näköyhteydettömässä tilanteissa. Moniteiden suuremmista vaimennuksista johtuen viive ja kulmahajonnat ovat pienemmät verrattaessa matalempiin taajuuksiin. Peiliheijastus on diffuusisirontaa merkittävämpi radioaallon etenemismekanismi johtaen pienempiin klustereiden kulmahajeisiin matalempiin taajuuksiin verrattuna. Monikerroksisen lasin läpäisyvaimennus on samankaltainen kuin alemmilla taajuuksilla, kun sitä vastoin betoniseinän vaimennus on muutaman desibelin suurempi kuin alemmilla taajuuksilla. Lopulta geometriaan perustava stokastinen radiokanavamalli validoidaan määritellyillä parametreilla. MIMO kanava uudelleen rakennetaan lisäämällä kolmiulotteiset antennien säteilykuviot estimoituihin radioaallon etenemisteihin. Vastaavasti radiokanava simuloidaan näennäisesti deterministisellä radiokanavageneraattorilla (QuaDRiGa) käyttäen määriteltyjä mallin parametreja. Kanavakapasiteettia, Demmel ehtolukua ja suhteellista ehtolukua käytetään vertailumittareina uudelleen rakennetun ja simuloidun kanavan välillä. Tulosten perusteella uudelleen rakennettu MIMO kanava on yhteensopiva simuloidun radiokanavan kanssa.

Theoretical principles of the sixport measurement method are presented. Description of theoretical design and influence of its parameters on measurement precision follows. Simple sixport measurement system was made and its parameters are described. As the main thesis contribution there is described a new approach to method with more detectors in the system. Mean features are more valid sixports at one specific frequency and frequency bandwidth aviable up to 1 : 100 and more. Such a wideband measurement system was designed for the frequencies between 50 and 2680 MHz and its parameters are presented in the work.

The VSWR is an important entity when assessing the properties of an antenna. This report presents measurements of the VSWR, related to antennas, by means of a Vector Network Analyzer. The open/short/load calibration method is used as a preparation before the actual measurement in order to obtain accurate results. The way that the VSWR depends on frequency is illustrated by three measurment methods: direct measurement of the VSWR, by using 𝑆11, or by using the Smith chart. The results are compared and conclusions are drawn.

La caractérisation des composants hyperfréquences après leur fabrication, est généralement réalisée par la mesure de paramètres S à l’aide d’un analyseur vectoriel de réseau (VNA). La précision de mesure dépend étroitement de la qualité du calibrage de l’analyseur vectoriel, qui permet de corriger les erreurs inhérentes au système de mesure. Des composants particuliers, dits étalons ou standards, dont les paramètres sont complètement ou partiellement connus, sont mesurés lors de la procédure de calibrage afin de déterminer les erreurs systématiques du système. La réalisation d’un circulateur coplanaire (les trois ports sont à 120 degrés les uns des autres) travaillant autour de 40 GHz est l’un des axes de recherche du laboratoire depuis plusieurs années et la caractérisation des prototypes a toujours été un souci important. Le calibrage est réalisé avec un kit commercial, avec les pointes positionnées en face à face. La mesure des dispositifs CPW à accès orthogonaux ou obliques après un calibrage avec un ensemble de standards conventionnels (droits) peut engendrer des erreurs supplémentaires. L’objectif de notre travail est donc de concevoir un ensemble de standards à accès inclinés à 120 degrés permettant de calibrer l’analyseur vectoriel « 2-ports » en positionnant directement les pointes à 120 degrés. La méthode de calibrage TRL (THRU – REFLECT - LINE) a été choisie. Le travail à accomplir se résume comme suit : - faire une étude de simulation du nouveau kit de calibrage à concevoir ; - mettre en évidence l’effet des accès coudés sur les lignes de transmission des standards ; - proposer une méthode de calcul qui tient compte de ces effets lors de la procédure de calibrage ; - mesurer quelques échantillons réalisés afin de vérifier la validité de la procédure de calibrage proposée. Les résultats obtenus au cours de ce travail ont pu être validés expérimentalement et offrent de nouvelles perspectives pour la mesure des composants planaires à accès non conventionnels / Microwave components characterization after the fabrication steps is usually performed by measuring S parameters using a Vector Network Analyzer (VNA). The measurement accuracy is highly dependent on the quality of the VNA calibration, which corrects the inherent errors in the measurement system. Specific components, called standards and whose parameters are completely or partially known, are measured during the calibration procedure to determine systematic errors of the system. Fabricating a coplanar circulator (the three ports are at 120 degrees position) functioning around 40 GHz is one of the laboratory’s research areas for several years and characterization of prototypes has always been a major concern. Usually, the calibration is made with a commercial kit ; probes are in face-to-face position. Measurements of CPW devices with orthogonal or bended accesses (120 degrees in our case) after VNA calibration with conventional (straight) set of standards may generate additional errors. The aim of our work is to design a set of standards with 120_ bended accesses allowing the calibration of the “2-ports” network analyzer. Therefore, probes are directly set at 120_ position. TRL (THRU - REFLECT -LINE) calibration procedure is chosen for the standards design. The work to be done is as follows : - to make a simulation study of the new calibration kit to design ; - to determine the bended accesses effects on the standards transmission lines ; - to propose a calculation method that takes account of these effects during the calibration procedure ; - to measure some fabricated samples to verify the validity of the proposed calibration procedure. The results of this research work have been experimentally validated and offer new perspectives for measuring planar components with unconventional accesses

Des circuits différentiels sont largement utilisés pour la conception de composants hyperfréquences principalement en raison de leur meilleure immunité au bruit. Ces circuits doivent être caractérisés au moyen de paramètres S en mode mixte (mode différentiel, mode commun et conversion entre les deux modes). De plus, la tendance à la miniaturisation et à l’intégration des dispositifs hyperfréquences conduit à l’utilisation de structures planaires ou coplanaires telles que les lignes micro-ruban ou les lignes coplanaires. La structure coplanaire avec les conducteurs déposés à la surface supérieure du substrat évite de réaliser des trous métallisés, et donc simplifie la fabrication et empêche l’apparition d’éléments parasites. Du point de vue de la métrologie électrique, il est nécessaire d’établir la traçabilité des mesures de paramètres S en mode mixte au Système International d’unités (SI). La méthode d’étalonnage Multimode Thru – Reflect – Line (TRL), dérivée de l’étalonnage TRL couramment utilisée pour les mesures de paramètres S de circuits asymétriques, est bien adaptée à cette problématique. En effet, l’impédance caractéristique, qui définit l’impédance de référence du système de mesure, peut être obtenue à partir des constantes de propagation déterminées lors de la procédure Multimode TRL et des capacités linéiques en DC.Nous présentons la première conception et la réalisation d’un kit d’étalonnage Multimode TRL et d’un kit de vérification à base des lignes coplanaires couplées en configuration « Ground – Signal – Ground – Signal – Ground » sur un substrat de quartz (SiO2) à faibles pertes diélectriques pour des mesures de paramètres S en mode mixte sur wafer de 1 GHz à 40 GHz. Les mesures sont effectuées à l’aide de deux méthodes : l’approche « one-tier » basée sur la procédure d’étalonnage Multimode TRL afin de déterminer et de corriger l’ensemble des erreurs systématiques ou bien l’approche « two-tier » qui fractionne la détermination et la correction des termes d’erreur en deux étapes dont la deuxième est associée à la méthode Multimode TRL. La faisabilité et la validation de ces techniques sont démontrées par des mesures d’éléments de vérification, constitués de lignes (adaptées, désadaptées et déséquilibrées) et d’atténuateurs en T, qui montrent un très bon accord entre les valeurs mesurées et simulées.La propagation des incertitudes est évaluée soit à partir du calcul des dérivées partielles à l’aide de l’outil Metas.Unclib ou bien par simulation numérique basée sur la méthode de Monte Carlo. La précision des mesures de paramètres S sous pointes dépend des sources d’influence attribuées aux mesures et aux imperfections des étalons telles que le bruit et la non-linéarité de l’analyseur de réseaux vectoriel, la stabilité des câbles, la répétabilité des mesures et la sensibilité dans la réalisation des étalons. Faute de temps, nous nous limitons à estimer la propagation d’incertitudes liées à la répétabilité de mesure des étalons et du dispositif sous test (DST) aux valeurs des paramètres S corrigés de la ligne désadaptée. Les résultats montrent que l’approche des dérivées partielles basée sur une approximation de la série de Taylor au premier ordre ne peut pas être utilisée avec précision à cause de l’influence significative de la non-linéarité des fonctions mathématiques de l’algorithme Multimode TRL. La méthode Monte Carlo s’avère alors plus précise bien qu’elle nécessite des temps de calcul très longs. / Differential circuits are widely used in the design of high frequency components mainly because of their better noise immunity. These circuits can be characterized using mixed-mode S parameters (differential- and common-mode S-parameters and cross-mode terms). Furthermore, the trend toward miniaturization and integration of microwave devices increases the need for planar or coplanar microwave integrated circuits such as micro-strip lines or coplanar waveguides. The ungrounded coplanar waveguide structure with all the conductors located on the same side of the substrate eliminates the need for via-holes, and thus simplifies manufacturing and prevents the appearance of some parasitic elements. From the viewpoint of electrical metrology, it is necessary to establish the traceability of the mixed-mode S-parameter measurements to the International System of Units (SI). The Multimode Thru-Reflect-Line (TRL) calibration method, derived from the commonly-used TRL calibration for S-parameter measurements of single-ended circuits, is particularly well suited for this purpose as the standards are traceable via dimensional measurements. The characteristic impedance, which defines the reference impedance of the measurement system, can be achieved from the propagation constants determined during the Multimode TRL calibration and the capacitances per unit length of the transmission line.We present the first design and realization of Multimode TRL calibration and verification kits using coupled coplanar lines in the "Ground - Signal - Ground - Signal - Ground" configuration on quartz (SiO2), the low-loss substrate, for on-wafer mixed-mode S-parameter measurements from 1 GHz to 40 GHz. Measurements are performed using two methods: the “one-tier” technique, based on the Multimode TRL calibration procedure, determines and corrects all systematic errors. The “two-tier” approach, in which the Multimode TRL is applied at the second-tier, is applied to measurement data that were partially corrected by the first calibration. The feasibility and the validation of the methods are demonstrated by measurements of matched, mismatched and unbalanced lines and T-attenuators showing good agreement between simulated and measured results.The propagation of uncertainty can be derived by the calculation of partial derivatives using the Metas.Unclib tool or by the numerical approach based on the Monte Carlo technique. The accuracy of on-wafer S-parameter measurements depends on sources of influence attributed to the measurements and to the imperfections of the standards such as the VNA noise and non-linearity, the cable stability, the measurement repeatability, and the sensitivity in calibration standards’ realization. We focus, first and foremost, on the propagation of uncertainties related to the repeatability of the standards and the device under test measurements to the corrected mixed-mode S-parameters of the mismatched line. The results show that the partial derivatives approach based on an approximation of the first-order Taylor series cannot be accurately used due to the significant influences of non-linear functions in the Multimode TRL algorithm. The Monte Carlo method is then more precise although it requires very long computation time.