Spelling suggestions: "subject:"nanopipelining"" "subject:"superpipelining""
1 |
Wave-Pipelined Multiplexed (WPM) Routing for Gigascale Integration (GSI)Joshi, Ajay Jayant 12 April 2006 (has links)
The main objective of this research is to develop a pervasive wire sharing technique that can be easily applied across the entire range of on-chip interconnects in a very large scale integration (VLSI) system. A wave-pipelined multiplexed (WPM) routing technique that can be applied both intra-macrocell and inter-macrocell interconnects is proposed in this thesis. It is shown that an extensive application of the WPM routing technique can provide significant advantages in terms of area, power and performance. In order to study the WPM routing technique, a hierarchical approach is adopted. A circuit-level, system-level and physical-level analysis is completed to explore the limits and opportunities to apply WPM routing to current VLSI and future gigascale integration (GSI) systems. Design, verification and optimization of the WPM circuit and measurement of its tolerance to external noise constitute the circuit-level analysis. The physical-level study involves designing wire sharing-aware placement algorithms to maximize the advantages of WPM routing. A system-level simulator that designs the entire multilevel interconnect network is developed to perform the system-level analysis. The effect of WPM routing on a full-custom interconnect network and a semi-custom interconnect network is studied.
|
2 |
High Speed Circuit Design Based on a Hybrid of Conventional and Wave PipeliningSulistyo, Jos Budi 03 October 2005 (has links)
The increasing capabilities of multimedia appliances demand arithmetic circuits with higher speed and reasonable power dissipation. A common technique to attain those goals is synchronous pipelining, which increases the throughput of a circuit at the expense of longer latency, and it is therefore suitable where throughput takes priority over latency.
Two synchronous pipelining approaches, conventional pipelining and wave pipelining, are commonly employed. Conventional pipelining uses registers to divide the circuit into shorter paths and synchronize among sub-blocks, while wave pipelining uses the delay of combinational elements to perform those tasks. As wave pipelining does not introduce additional registers, in principle, it can attain a higher throughput and lower power consumption. However, its throughput is limited by delay variations, while delay balancing often leads to increased power dissipation.
This dissertation proposes a hybrid pipelining method called HyPipe, which divides the circuit into sub-blocks using conventional pipelining, and applies wave pipelining to each sub-block. Each sub-block is derived from a single base circuit, leading to a better delay balance and greater throughput than with heterogeneous circuits. Another requirement for wave pipelining to achieve high speed is short signal rise and fall times. Since CMOS wide-NAND and wide-NOR gates exhibit long rise and fall times and large delay variations, they should be decomposed. We show that the straightforward decomposition using alternating levels of NAND and NOR gates results in large delay variations. Therefore, we propose a new decomposition method using only one gate type. Our method reduces delay variations by up to 39%, and it is appropriate for wave pipelining based on standard-cells or sea-of-gates.
We laid out a 4x4 HyPipe multiplier as a proof of concept and performed a post-layout SPICE simulation. The multiplier achieves a throughput of 4.17 billion multiplications per second or a clock period of 2.52 four-load inverter delays, which is almost twice the speed of any existing multiplier in the open literature. When the supply voltage is reduced to 1.2 V from 1.8 V, its power consumption is reduced from 76.2 mW to 18.2 mW while performing 2.33 billion multiplications per second. / Ph. D.
|
3 |
Throughput-Centric Wave-Pipelined Interconnect Circuits for Gigascale IntegrationDeodhar, Vinita Vasant 31 October 2005 (has links)
The central thesis of this research is that VLSI interconnect design strategies should shift from using global wires that can support only a single binary transition during the latency of the line to global wires that can sustain multiple bits traveling simultaneously along the length of the line. It is shown in this thesis that such throughput-centric multibit transmission can be achieved by wave-pipelining the interconnects using repeaters. A holistic analysis of wave-pipelined interconnect circuits, along with the full-custom optimization of these circuits, is performed in this research. With the help of models and methodologies developed in this thesis, the design rules for repeater insertion are crafted to simultaneously optimize performance, power, and area of VLSI global interconnect networks through a simultaneous application of voltage scaling and wire sizing. A qualitative analysis of latency, throughput, signal integrity, power dissipation, and area is performed that compares the results of design optimizations in this work to those of conventional global interconnect circuits. The objective of this thesis is to study the circuit- and system-level opportunities of voltage scaling, wire sizing, and repeater insertion in wave-pipelined global interconnect networks that are implemented in deep submicron technologies.
|
4 |
Wave Component Sampling Method For High Performance Pipelined CircuitsSever, Refik 01 September 2011 (has links) (PDF)
In all of the previous pipelining methods such as conventional pipelining, wave pipelining, and mesochronous pipelining, a data wave propagating on the combinational circuit is sampled whenever it arrives to a synchronization stage. In this study, a new wave-pipelining methodology named as Wave Component Sampling Method (WCSM), is proposed. In this method, only the component of a wave, whose maximum and minimum delay difference exceeds the tolerable value, is sampled, and the other components continue to propagate on the circuit. Therefore, the total number of registers required for synchronization decreases significantly. For demonstrating the effectiveness of the proposed WCSM, an 8x8 bit carry save In all of the previous pipelining methods such as conventional pipelining, wave pipelining, and mesochronous pipelining, a data wave propagating on the combinational circuit is sampled whenever it arrives to a synchronization stage. In this study, a new wave-pipelining methodology named as Wave Component Sampling Method (WCSM), is proposed. In this method, only the component of a wave, whose maximum and minimum delay difference exceeds the tolerable value, is sampled, and the other components continue to propagate on the circuit. Therefore, the total number of registers required for synchronization decreases significantly. For demonstrating the effectiveness of the proposed WCSM, an 8x8 bit carry save adder (CSA) multiplier is implemented using 0.18µ / m CMOS technology. A generic transmission gate logic block with optimized output delay variation depending on the input pattern is designed and used in all of the sub blocks of the multiplier. Post layout simulation results show that, this multiplier can operate at a speed of 3GHz, using only 70 latches. Comparing with the mesochronous pipelining scheme, the number of the registers is decreased by 41% and the total power of the chip is also decreased by 9.5% without any performance loss. An ultra high speed full pipelined CSA multiplier with an operating frequency of 5GHz is also implemented with WCSM. The number of registers is decreased by 45%, and the power consumption of the circuit is decreased by 18.4% comparing with conventional or mesochronous pipelining methods. WCSM is also applied to different multiplier structures employing booth encoders, Wallace trees, and carry look-ahead adders. Comparing full pipelined 8x8 bit WCSM multiplier with the conventional pipelined multiplier, the number of registers in the implementation of booth encoder, Wallace tree, and carry look-ahead adder is decreased by 30%, 51%, and %62, respectively.
|
Page generated in 0.0634 seconds