Recently, efforts have been made for self-powering the batteries and portable electronic devices by piezoelectric nanogenerators. The piezoelectric nanogenerators can work as a power source for nano-systems and also as an active sensor. The piezoelectric nanogenerator is a device that converts random mechanical energy into electrical energy by utilizing the semiconducting and piezoelectric properties. Also, the mechanical energy is always available in and around us for powering these nano devices. The aim of the present thesis work is to explore 1D and 2D ZnO nanostructures (nanorods and nanosheets) on metal alloy substrates for the development of piezoelectric nanogenerators in energy harvesting and sensors applications. Hydrothermal synthesis method was adopted for the growth of ZnO nanostructures. The nanogenerators were fabricated by using the optimized synthesis parameters and subsequently studied their performance for power generation and as an active speed sensor. These 1D and 2D nanostructures based nanogenerators have opened up a new window for the energy harvesting applications and sensors development. The thesis is divided into following six chapters. Chapter 1: This chapter gives a general introduction about energy harvesting devices such as nanogenerators, available energy sources, mechanical energy harvesting, ZnO material and the details on hydrothermal synthesis process. A brief literature survey on different applications of piezoelectric nanogenerators is also included. Chapter 2: A novel flexible metal alloy (Phynox) and its properties along with its applications are discussed in this chapter. Details on the synthesis of 1D ZnO nanorods on Phynox alloy substrate by hydrothermal method are presented. Further, the optimization of parameters such as growth temperature, seed layer annealing and substrate temperature effects on the synthesis of ZnO nanorods are discussed in detail. As-synthesized ZnO nanorods have been characterized using XRD, FE-SEM, TEM and XPS. Chapter 3: It reports on the fabrication of piezoelectric nanogenerator on Phynox alloy substrate as power generating device by harvesting the mechanical energy. Initially, the performance of the nanogenerator for power generation due to finger tip impacts was studied and subsequently its switching polarity test was also carried out. Output voltage measurements were carried out using the in-house developed experimental setup. Stability test was also carried out to see the robustness of the nanogenerator. Finally, the output voltage response of the nanogenerator was studied for its use as an active speed sensor. Chapter 4: Synthesis of Al doped 2D ZnO nanorsheets on Aluminum alloy (AA-6061) substrate by hydrothermal method is reported in this chapter. The optimized parameters such as growth temperature and growth time effects on the synthesis of ZnO nanosheets are discussed. As-synthesized ZnO nanosheets were characterized using XRD, FE-SEM, TEM and XPS. The Al doping in ZnO is confirmed by EDXS and XPS analysis. Chapter 5: Cost effective fabrication of Al doped 2D ZnO nanosheets based nanogenerator for direct current (DC) power generation is reported in this chapter. The performance of the nanogenerator for DC power generation due to finger tip impacts was studied and subsequently its switching polarity test was also carried out. Output voltage measurements were carried out using the in-house developed experimental setup. Stability test was also carried out to see the robustness of the nanogenerator. Finally, the DC output voltage response of the nanogenerator was studied for its use as an active speed sensor. Chapter 6: The first section summarizes the significant features of the work presented in this thesis. In the second section the scope for carrying out the further work is given.

Tesis por compendio / [ES] La presente Tesis Doctoral se centra en el desarrollo de nanoestructuras de óxido de zinc (ZnO) mediante anodizado electroquímico en diferentes condiciones para su aplicación en el área energética, en particular, en la producción de hidrógeno mediante la rotura fotelectrocatalítica de la molécula de agua. El hidrógeno es un vector energético que se plantea como solución al problema asociado a la intermitencia diurna y estacional de la energía solar y a la variabilidad en la demanda de energía. Por otra parte, el ZnO es un material semiconductor prometedor como fotocatalizador para la producción de hidrógeno debido a sus características y propiedades. En este contexto, el ZnO es un material muy abundante, y por extensión, relativamente barato, no es tóxico y presenta una energía de banda prohibida de 3,37 eV, lo que le permite la absorción de fotones en la región UV del espectro solar. Asimismo, las posiciones de sus bandas de energía son apropiadas para llevar a cabo la fotoelectrólisis del agua. En la presente Tesis Doctoral la síntesis de nanoestructuras de ZnO se llevó a cabo mediante anodizado electroquímico, puesto que este método presenta múltiples ventajas frente a otros métodos de síntesis habituales. En general, el anodizado electroquímico constituye un método rápido, sencillo y eficaz de síntesis de nanoestructuras de ZnO mediante el que es posible diseñar las características superficiales de las nanoestructuras (tamaño y morfología) a través del control de sus parámetros. Como resultado de una revisión bibliográfica en profundidad, se analizó la influencia de los parámetros del anodizado en las características superficiales de las nanoestructuras. Además, se investigaron aquellos parámetros cuya influencia todavía no había sido analizada. Por una parte, se estudió la influencia de emplear diferentes condiciones hidrodinámicas de flujo (dadas por la variación de la velocidad de rotación del electrodo). Por otra parte, se estudió la influencia conjunta de modificar el electrolito con la adición de un disolvente orgánico (etanol o glicerol en distintas proporciones) y variar la velocidad de rotación del electrodo. Las muestras de ZnO sintetizadas se sometieron a una caracterización morfológica, estructural, electroquímica y fotoelectroquímica y se estudiaron sus propiedades para ser empleadas como fotocatalizadores en la producción de hidrógeno. De acuerdo con los resultados, las diferentes condiciones de anodizado dieron lugar a diversas nanoestructuras de ZnO con diferentes características superficiales y fotoelectrocatalíticas. Así, se obtuvieron nanoestructuras de elevada área superficial con morfologías de nanocables de distintos tamaños, nanotubos, nanoesferas y nanoesponjas. Asimismo, tras el calentamiento térmico las muestras presentaron una estructura cristalina hexagonal wurtzita con elevada cristalinidad y la presencia de defectos estructurales. Igualmente, las nanoestructuras sintetizadas presentaron una elevada fotoactividad, dada por los valores elevados de densidad de fotocorriente, presentando propiedades apropiadas para su utilización en la producción de hidrógeno. La muestra que presentó el valor de densidad de fotocorriente más elevado (0,34 mA/cm2) fue la muestra de nanocables de ZnO anodizada a 0 rpm en un electrolito con un contenido en etanol del 10 % en volumen. En la aplicación de dicha muestra en la producción de hidrógeno se obtuvo un volumen teórico de hidrógeno de 1,55 litros por hora de sol y metro cuadrado de ZnO. / [CA] La present Tesi Doctoral se centra en el desenvolupament de nanoestructures d'òxid de zinc (ZnO) mitjançant anoditzat electroquímic en diferents condicions per a l'aplicació en l'àrea energètica, en particular, en la producció d'hidrogen mitjançant el trencament fotelectrocatalític de la molècula d'aigua. L'hidrogen és un vector energètic que es planteja com a solució al problema associat a la intermitència diürna i estacional de l'energia solar i a la variabilitat en la demanda d'energia. D'altra banda, el ZnO és un material semiconductor prometedor com a fotocatalitzador per a la producció d'hidrogen degut a les seues característiques i propietats. En aquest context, el ZnO és un material molt abundant, i per extensió, relativament barat, no és tòxic i presenta una energia de banda prohibida de 3,37 eV, la qual cosa li permet l'absorció de fotons a la regió UV de l'espectre solar. Així mateix, les posicions de les seues bandes d'energia són apropiades per a dur a terme la fotoelectròlisi de l'aigua. En la present Tesi Doctoral la síntesi de nanoestructures de ZnO es va dur a terme mitjançant anoditzat electroquímic, ja que aquest mètode presenta múltiples avantatges enfront d'altres mètodes de síntesi habituals. En general, l'anoditzat electroquímic constitueix un mètode ràpid, senzill i eficaç de síntesi de nanoestructures de ZnO mitjançant el qual és possible dissenyar les característiques superficials de les nanoestructures (grandària i morfologia) a través del control dels seus paràmetres. Com a resultat d'una revisió bibliogràfica en profunditat, es va analitzar la influència dels paràmetres de l'anoditzat en les característiques superficials de les nanoestructures. A més, es van investigar aquells paràmetres la influència dels quals encara no havia sigut analitzada. D'una banda, es va estudiar la influència d'emprar diferents condicions hidrodinàmiques de flux (donades per la variació de la velocitat de rotació de l'elèctrode). D'altra banda, es va estudiar la influència conjunta de modificar l'electròlit amb l'addició d'un dissolvent orgànic (etanol o glicerol en diferents proporcions) i variar la velocitat de rotació de l'elèctrode. Les mostres de ZnO sintetitzades es van sotmetre a una caracterització morfològica, estructural, electroquímica i fotoelectroquímica i es van estudiar les seues propietats per a ser emprades com fotocatalitzadors en la producció d'hidrogen. D'acord amb els resultats, les diferents condicions d'anoditzat van donar lloc a diverses nanoestructures de ZnO amb diferents característiques superficials i fotoelectrocatalítiques. Així, es van obtindre nanoestructures d'elevada àrea superficial amb morfologies de nanocables de diferents grandàries, nanotubs, nanoesferes i nanoesponges. Així mateix, després del calfament tèrmic les mostres van presentar una estructura cristal·lina hexagonal wurtzita amb elevada cristallinitat i la presència de defectes estructurals. Igualment, les nanoestructures sintetitzades van presentar una elevada fotoactivitat, donada pels valors elevats de densitat de fotocorrent, presentant propietats apropiades per a la seua utilització en la producció d'hidrogen. La mostra que va presentar el valor de densitat de fotocorrent més elevat (0,34 mA/cm²) va ser la mostra de nanocables de ZnO anoditzada a 0 rpm en un electròlit amb un contingut en etanol del 10% en volum. En l'aplicació d'aquesta mostra en la producció d'hidrogen es va obtindre un volum teòric d'hidrogen de 1,55 litres per hora de sol i metre quadrat de ZnO. / [EN] This Doctoral Thesis focuses on the development of zinc oxide (ZnO) nanostructures by electrochemical anodization under different conditions for its application in the energy area, in particular, in the production of hydrogen through photoelectrochemical water splitting. Hydrogen is an energy vector that is proposed as a solution to the problem associated with the diurnal and seasonal intermittency of solar energy and the variability in the energy demand. On the other hand, ZnO is a promising semiconductor material as a photocatalyst for hydrogen production due to its characteristics and properties. In this context, ZnO is a very abundant material, and by extension, relatively cheap, it is non-toxic and has a band-gap energy of 3.37 eV, which allows it to absorb photons in the UV region of the solar spectrum. Besides, the positions of ZnO energy bands are appropriate to carry out photoelectrochemical water splitting. In the present Doctoral Thesis, the synthesis of ZnO nanostructures was carried out by electrochemical anodization, since this method has multiple advantages compared to other common synthesis methods. In general, electrochemical anodization constitutes a fast, simple, and effective method of synthesis of ZnO nanostructures by means of which it is possible to design the surface characteristics of the nanostructures (size and morphology) by controlling anodization parameters. As a result of an in-depth bibliographic review, the influence of anodization parameters on the surface characteristics of nanostructures was analyzed. In addition, those parameters whose influence had not yet been analyzed were investigated. On the one hand, the influence of using different controlled hydrodynamic conditions (given by the variation of the rotation speed of the electrode) was studied. On the other hand, the influence of both modifying the electrolyte with the addition of an organic solvent (ethanol or glycerol in different proportions) and varying the electrode rotation speed was studied. The synthesized ZnO samples were subjected to a morphological, structural, electrochemical and photoelectrochemical characterization and their properties were studied to be used as photocatalysts in hydrogen production. According to the results, the different anodization conditions gave rise to various ZnO nanostructures with different surface and photoelectrocatalytic characteristics. Thus, high surface area nanostructures were obtained with morphologies of nanowires of different sizes, nanotubes, nanospheres and nanosponges. Likewise, after thermal annealing the samples presented a wurtzite hexagonal crystalline structure with high crystallinity and the presence of structural defects. Likewise, the synthesized nanostructures presented high photoactivity, given by the high values of photocurrent density, presenting appropriate properties for their use in the production of hydrogen. The sample that presented the highest photocurrent density value (0.34 mA / cm2) was the ZnO nanowires anodized at 0 rpm in an electrolyte with an ethanol content of 10 % by volume. In the application of this sample in the hydrogen production, a theoretical volume of hydrogen of 1.55 liters per hour of sun and square meter of ZnO was obtained. / Authors would like to express their gratitude for the financial support to the Generalitat Valenciana and to the European Social Fund within the subvention to improve formation and employability of technical and management staff of I+D (GJIDI/2018/A/067) and for its financial support through the project: IDIFEDER/018/044. Authors also thank for the financial support to the Ministerio de Economía y Competitividad (Project Code: CTQ2016-79203-R) and to the Ministerio de Ciencia e Innovación-Agencia Estatal de Investigación (Project Code: PID2019-105844RB-I00) for its help in the Laser Raman Microscope acquisition (UPOV08-3E- 012) and for the co-finance by the European Social Fund. / Batista Grau, P. (2021). Desarrollo de nanoestructuras de ZnO mediante anodizado electroquímico en diferentes condiciones para su aplicación en el área energética [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/172606 / Compendio

One-dimensional (1D) nanostructures have gained tremendous attention over the last decade due to their wide range of potential applications. Particularly, ZnO 1D nanostructures have been investigated with great interest due to their versatility in synthesis with potential applications in electronics, optics, optoelectronics, sensors, photocatalysts and nanogenerators. The thesis deals with the challenges and the answer to grow ZnO 1D nanostructure by vapor phase transport (VPT) continuously without any length limitation. The conventional VPT technique has been modified for the non-catalytic growth of ultralong ZnO 1D nanostructures and branched structures in large area with controllable aspect ratio. It has been shown that the aspect ratio can be controlled both by thermodynamically (temperature) and kinetically (vapour flux). The thesis also deals with the fabrication of carbon nanotube (CNT) -ZnO based multifunctional devices and the field emission performance of ZnO nanowires by employing various strategies. The entire thesis has been organised as follows: Chapter 1 deals with Introduction. In this chapter, importance of ultralong nanowires and significance of ultralong ZnO nanowires has been discussed. Various efforts to grow ultralong ZnO nanowire with their advantages and disadvantages have been summarised. Lastly the significance of forming ZnO nanowires based nano hybrid structures and importance of doping in ZnO nanowires and has also been discussed. Chapter 2 deals with experimental procedure and characterization. In this chapter, a single step VPT method for the growth of ultralong ZnO nanowires that incorporates local oxidation barrier for the source has been described. The synthesized nanowires were characterised by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), Raman & photoluminescence. Chapter 3 deals with growth of ZnO nanowires, controlling the aspect ratio of ZnO nanowires, and role of other experimental aspects. In this chapter, a way to grow nanowires continuously without any apparent length limitation, a way to control the diameter of the nanowires kinetically without catalyst particle or seed layer and obtaining smaller diameter of the nanowires by non-catalytic growth as compared to that set by the thermodynamic limit has been discussed. Furthermore, the significance and importance of local oxidation barrier on source for protecting them from degradation, ensuring the continuous supply of vapour and enabling the thermodynamically and kinetically controlled growth of nanowires has been discussed. Lastly, the scheme for large area deposition and a method to use same source material for several depositions has been presented. Chapter 4 deals with multifunctional device based on CNT -ZnO Nanowire Hybrid Architectures same device can be used as a rectifier, a transistor and a photodetector. In this chapter, the fabrication of CNT arrays-ZnO nanowires based hybrid architectures that exhibit excellent high current Schottky like behavior with p-type conductivity of ZnO has been discussed. CNT-ZnO hybrid structures that can be used as high current p-type field effect transistors (FETs) and deliver currents of the order of milliamperes has been presented. Furthermore, the p-type nature of ZnO and possible mechanism for the rectifying characteristics of CNT-ZnO has been discussed. Lastly, the use of hybrid structures as ultraviolet detectors where the current on-off ratio and the response time can be controlled by the gate voltage has been presented and also an explanation for photoresponse behaviour has been provided. Chapter 5 deals with the substrate-assisted doping of ZnO nanowires grown by this technique. In this chapter, the non-catalytic growth of ZnO nanowires on multiwalled carbon nanotubes (MWCNTs) and soda lime glass (SLG) with controlled aspect ratio has been presented. The elemental mapping to confirm the presence and distribution of carbon and sodium in ZnO nanowires and the transport studies on both carbon and sodium doped ZnO has also been presented. Furthermore the stability of carbon doped ZnO has also been presented. Lastly, the advantage of growing ZnO nanowires on MWCNTs and overall advantage associated with this technique has been discussed. Chapter 6 deals with formation of ZnO nanowire branched structures. In this chapter, a possibility to grow ZnO nanowires on already grown ZnO nanowires has been demonstrated. The formation of branched structure during multiple growth of ZnO nanowire on ZnO nanowire has been presented and evolution of aspect ratio in these branched structures has been discussed. Furthermore, the advantage of using ZnO branched structures and also the ZnO nanoneedles on MWCNT mat for field emission has been presented. Chapter 7 summarizes all the findings of the thesis.

Zinc oxide (ZnO) is perhaps one of the most widely studied material in the last two decades. It has received so much of attention because of its incredible potential for wide ranging applications. ZnO is a wide band gap semiconductor (Eg = 3.37 eV at 300 K) with a rather large excitonic binding energy (~60 meV). This combination of properties makes it an ideal choice for several optoelectronic devices that can easily work at room temperature. ZnO is a truly multifunctional material possessing several desirable electrical, optical, optoelectronic, and piezoelectric properties. In addition, it is highly amenable to production of various kinds of nanostructures such as nanorods, nanotubes, nanoribbons, nanoneedles, etc., which makes it even more desirable for nanoscale devices. Examples of ZnO based nanodevices could include photodiodes, photodetectors, nano-lasers, field-emission devices and memristors. In order to make such devices, one could need device quality nanostructures that must be reproducible and cost effective. Naturally, one has to look for a synthesis process that has great controls and is relatively inexpensive. The study provided here shows that among the various methods available for ZnO synthesis, the microwave-assisted chemical synthesis offers outstanding advantages in terms of rapid growth of nanostructures, economical use of energy and excellent controls of process parameters. In order to produce device quality ZnO nanostructures using microwave-assisted synthesis, one has to study the effect of various process parameters and optimise them for the desired growth. Therefore, in the current study, first, a systematic study was undertaken to synthesize ZnO nanostructures both in a aqueous and non-aqueous medium and their characterization was carried out in order to understand the effect of microwave power, time of irradiation, pressure, solvent and salt concentration, etc. The goal was to develop synthesis protocols for various kinds of nanostructures that could guarantee reproducibility, good yield, and device quality structures. This study has led to successful growth of ZnO nanostructures on various substrates, vertically aligned ZnO nanorods and templated arrays of desired structures, all with outstanding properties of the structures as confirmed by XRD, MicroRaman, photoluminescence, cathodoluminescence, FESEM, TEM, PFM studies and pole figure analysis. Piezoelectric force microscopy (PFM) and physical property measurement system (PPMS, Quantum Design), have been used to study the multifunctional properties of ZnO nanostructures. The PFM is a powerful technique to measure the local piezoelectric coefficient of nanostructures and nanoscale thin films. PFM works on the converse piezoelectric effect in which electric potential is applied and mechanical strain is measured using a cantilever deflection. The PFM (Brucker’s AFM dimension Scan Assist) was used to characterize individual ZnO nanorods. Extensive studies were carried out with PFM measurements and it was observed that the nanorods consistently showed high piezoelectric coupling coefficients (d33~50-154 pm/V). It was also found that the variation in d33 depended on morphology and size of nanostructure. The multifunctional properties were observed in small ZnO nanocrystals (NCs). Such high values of piezoelectric coupling coefficients open the door for novel ZnO based nanoscale sensors and actuators. The synthesized ZnO nanostructures were further optimized and characterized keeping in view three device applications namely Field emission, Memristors and Gas Sensors. The fabrication and characterization of these three devices with ZnO nanostructure was carried out using electron beam lithography and direct laser writing micromachining. Device fabrication using lithography involved several steps such as substrate cleaning, photoresist spin coating, pre-baking, post-baking, pattern writing, developing, sputtering/deposition of material for lift-off, ZnO growth, and overlay lithography. For field emission devices, high quality, well aligned, c-axis oriented ZnO nano-needles were grown on sputter coated Ti/Pt (20nm/100nm) on SiO2/Si substrate by rapid microwave-assisted method in aqueous medium. The diameter of the tip was found to be 1~2 nm and the length of the rod was approximately 3~5μm. For a particular batch the tip size, morphology, and lengths were found to be the same and highly repeatable. Pole figure analysis revealed that nanorods were highly oriented towards <002> direction. Field-emission measurements using the ZnO nanoneedles arrays as cathode showed very low turn-on electric field of 0.9 V/μm and a very high field enhancement factor ~ 20200. Such a high emission current density, low turn-on electric field, and high field enhancement factor are attributed to the high aspect ratio, narrow tip size, high quality and single crystallinity of the nanoneedles. The high emission current density, high stability, low threshold electric field (0.95 V/μm) and low turn-on field make the ZnO nanoneedle arrays one of the ideal candidates for field-emission displays and field emission sensors. In the suitability of ZnO nanostructures for memristor application it was found that the single crystalline ZnO nanorods were not suitable as they did not show memristive behaviour but the ZnO nanorods with native defects exhibited considerable memristive behaviour. Therefore the microwave-assisted grown ZnO nanorods with defects were used to fabricate memristive devices. Single and multiple ZnO nanorods based memristors were fabricated using electron beam lithography. These devices were characterized electrically by measuring the hysteresis in the I/V characteristics. A high degree of repeatability has been established in terms of growth, device fabrication, and measurements. The switching in single nanorod based devices was found to have “ON-to- OFF” resistance ratio of approximately 104 and current switching ratio (ION/IOFF) of 106. Gas sensing based on electrical resistance change depends on absorption and desorption rate of gases on the analyte which is governed by surface properties, morphologies and activation energy. Therefore, various morphologies of nanostructure were grown for gas sensing application. Through experimentation, the emphasis shifted to c-axis oriented ZnO nanostructures on SiO2 substrate for gas sensing. The c-axis orientation of ZnO nanostructures was preferred mainly due to its huge surface area. The measurements showed that the c-axis oriented ZnO nanorods were excellent hydrogen sensors, able to detect H2 as low concentration as 2 ppm, even when the sensing temperature is as low as 200 ˚C. However, oxygen sensing was achieved at a higher temperature (300 ˚C). Thus, the study undertaken in this thesis presents a microwave based rapid and economical method for synthesizing high quality, device grade ZnO nanostructures, their extensive characterization that shows the multifunctional properties of these structures, and there examples of varied device applications of the synthesized nanostructures as field emitters, memristors, and gas sensors.

In recent years, there has been growing interests on II-VI semiconductor nanostructures, which are suitable for applications in electronics and optoelectronic devices such as solar cells, UV lasers, sensors, light emitting diodes and field emission displays. II-VI semiconductor nanostructures with different morphologies such as wires, belts, rods, tubes, needles, springs, tetrapods, plates, hierarchical structures and so on, have been widely grown by vapor transport methods. However the process conditions used for the growth of nanostructures still remains incompatible for device fabrication. The realization of practical nanoscale devices using nanostructured film depends mainly on the availability of low cost and lower processing temperatures to manufacture high purity nanostructures on a variety of substrates including glass and polymer. In this thesis work, studies have been made on the growth and characterization of II-VI semiconductor nanostructures prepared at room temperature, under high vacuum, without employing catalysts or templates. (i) ZnO nanostructured films with different morphology such as flowers, needles and shrubs were deposited at room temperature on glass and polymer substrates by plasma assisted reactive process. (ii) Zn/ZnO core/shell nanowires were grown on Si substrates under optimized oxygen partial pressure. Annealing of this core shell nanowire in high vacuum resulted in the formation of ZnO nanocanals. (iii) ZnS and ZnSe nano and microstructures were grown on Si substrates under high vacuum by thermal evaporation. The morphology, structural, optical properties and composition of these nano and microstructures were investigated by XRD, SEM, TEM, Raman, PL and XPS. The growth mechanism behind the formation of the different nanostructures has been explained on the basis of vapour-solid (VS) mechanism.