<p>This thesis is devoted to the investigation of passivesafety and inherent features of subcritical nucleartransmutation systems - accelerator-driven systems. The generalobjective of this research has been to improve the safetyperformance and avoid elevated coolant temperatures inworst-case scenarios like unprotected loss-of-ow accidents,loss-of-heat-sink accidents, and a combination of both theseaccident initiators. The specific topics covered are emergencydecay heat removal by reactor vessel auxiliary cooling systems,beam shut-off by a melt-rupture disc, safety aspects fromlocating heat-exchangers in the riser of a pool-type reactorsystem, and reduction of pressure resistance in the primarycircuit by employing bypass routes.</p><p>The initial part of the research was focused on reactorvessel auxiliary cooling systems. It was shown that an 80 MWthPb/Bi-cooled accelerator-driven system of 8 m height and 6 mdiameter vessel can be well cooled in the case of loss-of-owaccidents in which the accelerator proton beam is not switchedoff. After a loss-of-heat-sink accident the proton beam has tobe interrupted within 40 minutes in order to avoid fast creepof the vessel. If a melt-rupture disc is included in the wallof the beam pipe, which breaks at 150 K above the normal coreoutlet temperature, the grace period until the beam has to beshut off is increased to 6 hours. For the same vessel geometry,but an operating power of 250 MWth the structural materials canstill avoid fast creep in case the proton beam is shut offimmediately. If beam shut-off is delayed, additional coolingmethods are needed to increase the heat removal. Investigationswere made on the filling of the gap between the guard and thereactor vessel with liquid metal coolant and using water spraycooling on the guard vessel surface.</p><p>The second part of the thesis presents examinationsregarding an accelerator-driven system also cooled with Pb/Bibut with heat-exchangers located in the risers of the reactorvessel. For a pool type design, this approach has advantages inthe case of heat-exchanger tube failures, particularly if wateris used as the secondary uid. This is because a leakage ofwater from the secondary circuit into the Pb/Bi-cooled primarycircuit leads to upward sweeping of steam bubbles, which wouldcollect in the gas plenum. In the case of heatexchangers in thedowncomer steam bubbles may be dragged into the ADS core andadd reactivity. Bypass routes are employed to increase the owspeed in loss-of-ow events for this design. It is shown thatthe 200 MWth accelerator-driven system with heat-exchangers inthe riser copes reasonably well with both a loss-of-ow accidentwith the beam on and an unprotected loss-of-heat-sink accident.For a total-loss-of-power (station blackout) and an immediatebeam-stop the core outlet temperature peaks at 680 K. After acombined loss-of-ow and loss-of-heat-sink accident the beamshould be shut off within 4 minutes to avoid exceeding the ASMElevel D of 977 K, and within 8 minutes to avoid fast creep.Assuming the same core inlet temperature, both the reactordesign with heat-exchanger in the risers and the downcomershave similar temperature evolutions after a total-loss-ofpoweraccident.</p><p>A large accelerator-driven system of 800 MWth with a 17 mtall vessel may eventually become a standard size. For thishigher power ADS, the location of the heat-exchangers hasgreater impact on the natural convection capability. This isdue to that larger heatexchangers have more inuence on thedistance between the thermal centers during a lossof- owaccident. The design with heat-exchangers in the downcomers,the long-term vessel temperature peaks at 996 K during aloss-of-ow accident with the beam on. This does not pose athreat of creep rupture for the vessel. However, the locationof the heat-exchangers in the downcomers will probably requiresecondary coolant other than water, like for example oil (fortemperatures not higher than 673 K) or Pb/Bi coolant.</p>

In treatment of cancer using high energetic radiation the problem arises how to irradiate the tumor without damaging the healthy tissue in the immediate vicinity. In order to do this, intensity modulated radiation therapy (IMRT) is used. In this thesis, the general goal is to modulate the homogeneous radiation field delivered by an external accelerator using a multileaf collimator in comparison with beam modifying devices. In order to generate intensity modulated fields in a static mode with multileaf collimators, the heuristic algorithm of Galvin, Chen and Smith is used. This method aims at finding a segmentation with a small number of segments, taking account of mechanical constraints such as leaves can move only in one direction, on one row, the right and left leaves cannot overlap (Interleaf Collision) and also every element between the leaf and the side of the collimator to which the leaf is connected is also covered (no holes in leaves). During the implementation of the algorithm, the initial intensity matrix with the desired radiation rates is inserted and using essential transformations, a positive combination of special matrices, segments, corresponding to fixed positions of multileaf collimator are obtained. All calculations end with the superposition of segments which leads to the creation of the 3-D matrix that will be used to irradiate the tumor. The algorithm is implemented in C++. The calculations are fast and the procedure is user friendly. The model is implemented for the case of protection the spinal cord while treating a tumor in the neck area. Furthermore, dose distributions obtained with this model and beam modifying devices in the neck area were compared. / Κατά τη θεραπεία του καρκίνου με χρήση υψηλής ενέργειας ακτινοβολίας, πρόβλημα αποτελεί ο περιορισμός της ακτινοβολίας στον όγκο στόχο και ο περιορισμός της συμμετοχής του υγιούς ιστού, της γειτονικής περιοχής, στο ελάχιστο. Προκειμένου να επιλυθεί το πρόβλημα αυτό χρησιμοποιείται ακτινοθεραπεία με πεδία ακτινοβολίας διαμορφωμένης έντασης (Ιntensity Μodulated Radiαtion Therapy – IMRT), με τη βοήθεια των κατευθυντήρων πολλαπλών φύλλων (Multileaf Collimators- MLC). Στόχος της συγκεκριμένης διπλωματικής εργασίας είναι η διαμόρφωση του ομοιογενούς πεδίου ακτινοβολίας, που διανέμεται μέσω του γραμμικού επιταχυντή χρησιμοποιώντας κατευθυντήρα πολλαπλών φύλλων και η σύγκριση των αποτελεσμάτων της προσομοίωσης με τις συσκευές διαμόρφωσης δέσμης (Beam Modifying Devices). Προκειμένου να παραχθούν τα διαμορφωμένης έντασης πεδία ακτινοβολίας, σε στατική μορφή, χρησιμοποιήθηκε ο αλγόριθμος των Galvin, Chen και Smith. H μέθοδος αποσκοπεί στην τμηματοποίηση του πίνακα με τα επιθυμητά ποσοστά ακτινοβολίας σε έναν μικρό αριθμό τμημάτων “segments”, λαμβάνοντας υπόψιν μηχανικούς περιορισμούς. (i) Τα φύλλα δύναται να κινηθούν μόνο κατά μήκος μιας διεύθυνσης, (ii) σε μια γραμμή, το αριστερό και το δεξί φύλλο δεν μπορούν να επικαλυφτούν (Interleaf Collision) και (iii) κάθε στοιχείο μεταξύ του φύλλου και της πλευράς του διαμορφωτή, με την οποία είναι συνδεδεμένο, είναι πάντα καλυμμένο (Νo holes in leaves). Κατά την υλοποίηση του αλγορίθμου, εισάγεται ο αρχικός πίνακας με τα επιθυμητά ποσοστά ακτινοβολίας και με τη χρήσης κατάλληλων μετασχηματισμών, προκύπτει ένας συνδυασμός από ειδικούς πίνακες (segments), οι οποίοι αντιστοιχούν σε θέσεις των κατευθυντήρων πολλαπλών φύλλων και θα χρησιμοποιηθούν για την ακτινοβόληση του όγκου. Ο αλγόριθμος υλοποιήθηκε σε C++. Οι υπολογισμοί είναι γρήγοροι και η διεργασία είναι φιλική προς το χρήστη. Το μοντέλο υλοποιήθηκε για την περίπτωση προστασίας της σπονδυλικής στήλης κατά τη θεραπεία όγκου στην περιοχή του λαιμού. Τέλος, οι κατανομές δόσεις που προέκυψαν με την προαναφερθέν μοντέλο συγκρίθηκαν με αυτές των συσκευών διαμόρφωσης δέσμης.

An intra-pulse Interaction Point fast feedback system (IPFB) has been designed for the Next Linear Collider (NLC), to correct relative beam-beam misalignments at the Interaction Point (IP). This system will utilise the large beam-beam kick that results from the beam-beam interaction and apply a rapid correction to the beam misalignment at the IP within a single bunch train. A detailed examination of the IPFB system is given, including a discussion of the necessary electronics, and the results of extensive simulations based on the IPFB concept for fast beam correction are presented. A recovery of the nominal luminosity of the NLC is predicted well within the NLC bunch train of 266 ns. The FONT experiment - Feedback On Nanosecond Timescales - was proposed as a direct test of the IPFB concept and was realised at the NLC Test Accelerator at SLAC. As part of FONT, a novel X-band BPM was designed and tested at the NLCTA. The results of these tests with the NLCTA short and long-pulse beam are presented, demonstrating a linear response to the position of the 180 ns long-pulse beam: measurements show a time constant of ~1.5 ns and a precision of better than 20 microns. A novel BPM processor for use at X-band, making use of the difference-over-sum processing technique, is also presented in detail, with results given for both short and long-pulse beams. The FONT design concepts and modification of the IPFB system for use at the NLCTA are described. The design of a fast charge normalisation circuit, to process the difference and sum signals produced by the BPM processor, forming part of the FONT feedback circuit, is detailed extensively. Bench tests of the feedback electronics demonstrate the effectiveness of the normalisation and feedback stages, for which a signal latency of 11 ns was measured. These bench tests also show the correct operation of the normalisation and feedback principles. Finally, the results of a full beam test of the FONT system are presented, during which a system latency of 70 ns was measured. These rigorous tests establish the soundness of the IPFB scheme and show correction of a mis-steered bunch train within the full NLCTA pulse length of 180 ns.

Accelerator-driven systems have been proposed for incineration of transuranic elements from spent nuclear fuel. For safe operation of such facilities, a robust method for reactivity monitoring is required. Experience has shown that the performance of reactivity measurement methods in terms of accuracy and applicability is highly system dependent. Further investigations are needed to increase the knowledge data bank before applying the methods to an industrial facility and to achieve license to operate such a facility. In this thesis, two systems have been subject to investigation of various reactivity measurement methods. Conditions for successful utilization of the methods are presented, based on the experimental experience. In contrast to previous studies in this field, the reactivity has not only been determined, but also monitored based on the so called beam trip methodology which is applicable also to non-zero power systems. The results of this work constitute a part of the knowledge base for the definition of a validated online reactivity monitoring methodology for facilities currently being under development in Europe (XT-ADS and EFIT). / QC 20100621

Les travaux de cette thèse portent sur un insert dipolaire de supraconducteur à haute TC (SHT) en utilisant un câble multi-rubans torsadé pour un accélérateur des particules dans le cadre du projet EuCARD2 au CERN. L’insert dipolaire SHT est la seule possibilité aujourd'hui pour aller au-dessus de 16 T pour le futur accélérateur des particules à haute énergie. Deux spécifications de cet insert SHT sont les grands courants de fonctionnement (> 10 kA) et les champs de fond élevés (> 13 T) conduisant à des conditions de fonctionnement sévères. Pour répondre à ces attentes, un premier insert SHT de multi-rubans torsadé/ type de bloc est proposé sur la base des approches analytiques, numériques et expérimentales. Les travaux sont principalement classés dans le design d’insert dipolaire et le design de câble multi-rubans torsadé. Cette thèse se terminée avec la meilleure solution pour l’insert SHT de multi-rubans torsadé/ type de bloc en utilisant le câble partiellement isolé. / This Ph.D. deals with a high Tc superconducting (HTS) dipole insert using a twisted stacked cable for a particle accelerator in the framework of EuCARD2 project in CERN. The HTS dipole insert is the only possibility today to go above 16 T for the future high-energy particle accelerator. Two specifications of these HTS insert are large operating currents (> 10 kA) and high background fields (> 13 T) leading to severe operating conditions. To meet these expectations, a first Twisted Stacked/ Block-type HTS insert is proposed based on analytical, numerical and experimental approaches. The works are mainly classified into dipole insert design and twisted stacked cable design. This Ph.D. ends with the best solution for Twisted Stacked/ Block-type HTS insert using partially-insulated cable.

The trend in computer architectures has for several years been heterogeneous systems consisting of a regular CPU and at least one additional, specialized processing unit, such as a GPU.The different characteristics of the processing units and the requirement of multiple tools and programming languages makes programming of such systems a challenging task. Although there exist tools for programming each processing unit, utilizing the full potential of a heterogeneous computer still requires specialized implementations involving multiple frameworks and hand-tuning of parameters.To fully exploit the performance of heterogeneous systems for a single computation, hybrid execution is needed, i.e. execution where the workload is distributed between multiple, heterogeneous processing units, working simultaneously on the computation. This thesis presents the implementation of a new hybrid execution backend in the algorithmic skeleton framework SkePU. The skeleton framework already gives programmers a user-friendly interface to algorithmic templates, executable on different hardware using OpenMP, CUDA and OpenCL. With this extension it is now also possible to divide the computational work of the skeletons between multiple processing units, such as between a CPU and a GPU. The results show an improvement in execution time with the hybrid execution implementation for all skeletons in SkePU. It is also shown that the new implementation results in a lower and more predictable execution time compared to a dynamic scheduling approach based on an earlier implementation of hybrid execution in SkePU.

abstract: Three dimensional (3-D) ultrasound is safe, inexpensive, and has been shown to drastically improve system ease-of-use, diagnostic efficiency, and patient throughput. However, its high computational complexity and resulting high power consumption has precluded its use in hand-held applications. In this dissertation, algorithm-architecture co-design techniques that aim to make hand-held 3-D ultrasound a reality are presented. First, image enhancement methods to improve signal-to-noise ratio (SNR) are proposed. These include virtual source firing techniques and a low overhead digital front-end architecture using orthogonal chirps and orthogonal Golay codes. Second, algorithm-architecture co-design techniques to reduce the power consumption of 3-D SAU imaging systems is presented. These include (i) a subaperture multiplexing strategy and the corresponding apodization method to alleviate the signal bandwidth bottleneck, and (ii) a highly efficient iterative delay calculation method to eliminate complex operations such as multiplications, divisions and square-root in delay calculation during beamforming. These techniques were used to define Sonic Millip3De, a 3-D die stacked architecture for digital beamforming in SAU systems. Sonic Millip3De produces 3-D high resolution images at 2 frames per second with system power consumption of 15W in 45nm technology. Third, a new beamforming method based on separable delay decomposition is proposed to reduce the computational complexity of the beamforming unit in an SAU system. The method is based on minimizing the root-mean-square error (RMSE) due to delay decomposition. It reduces the beamforming complexity of a SAU system by 19x while providing high image fidelity that is comparable to non-separable beamforming. The resulting modified Sonic Millip3De architecture supports a frame rate of 32 volumes per second while maintaining power consumption of 15W in 45nm technology. Next a 3-D plane-wave imaging system that utilizes both separable beamforming and coherent compounding is presented. The resulting system has computational complexity comparable to that of a non-separable non-compounding baseline system while significantly improving contrast-to-noise ratio and SNR. The modified Sonic Millip3De architecture is now capable of generating high resolution images at 1000 volumes per second with 9-fire-angle compounding. / Dissertation/Thesis / Doctoral Dissertation Electrical Engineering 2015

O Laboratório do Acelerador Linear (LAL) do Instituto de Física da Universidade de São Paulo está construindo um acelerador de elétrons do tipo Mícrotron. O acelerador possui dois estágios de aceleração: o Mícrotron booster e o Mícrotron Principal. Atualmente, o sistema injetor do acelerador, que é um acelerador linear, dispõe de um feixe de elétrons de 1,9 MeV. Este feixe será inserido no primeiro estágio de aceleração, o Mícrotron booster, que já está construído e será testado em breve. Sua função é elevar a energia do feixe para 5 MeV. O objetivo deste trabalho é o de otimizar os parâmetros de operação do Mícrotron booster por meio de simulação. Também tivemos como objetivo estudar a viabilidade da adaptação do projeto original, com feixe de entrada de 1,765 MeV, para um feixe de entrada de 1,9 MeV. Tendo como foco principal encontrar a admitância do acelerador, foram desenvolvidas algumas rotinas de simulação. A admitância do Mícrotron booster para um feixe de 1,765 MeV foi calculada em 3,08 pi mm.mrad, 0,58 pi mm.mrad e 0,38 pi keV.rad para os espaços de fase horizontal, vertical e longitudinal, respectivamente. Para o feixe de 1,9 MeV, uma condição de aceleração foi encontrada e os valores de admitância foram 3,65 pi mm.mrad, 0,62 pi mm.mrad e 0,77 pi keV.rad para os mesmos espaços de fase. Dados de caracterizações do feixe, realizados em trabalhos anteriores foram utilizados para determinar a configuração das lentes quadrupolares responsáveis pela inserção do feixe no acelerador. Tais simulações darão suporte ao início de operação do Mícrotron booster, auxiliando na determinação dos parâmetros iniciais de operação e otimização dos parâmetros finais. / The Laboratório do Acelerador Linear is building a racetrack microtron electron accelerator. It has two acceleration stages: the booster and the main microtron. The injection system has already been commissioned and is delivering a 1.9-MeV continuous wave beam. This beam will be injected in the booster stage, which is ready to be commissioned, and should increase the energy to 5 MeV. The aim of this work is to optimize the operation parameters of the booster stage by means of simulation tools. We also studied the feasibility of injecting the 1.9 MeV beam in the booster, which has been designed to operate with a 1.765 MeV beam. Some simulation routines had to be developed in order to determine the admittance of the booster stage. For the 1.765 MeV beam the admittances were determined to be 3.08 pi mm.mrad, 0.58 pi mm.mrad, and 0.38 pi keV.rad for the transverse horizontal, transverse vertical, and longitudinal phase spaces, respectively. For the 1.9 MeV injection beam we were able to find a viable acceleration condition, with slightly better admittances: 3.65 pi mm.mrad, 0.62 pi mm.mrad, and 0.77 pi keV.rad, for the same phase spaces cited above. The injection beam has been characterized previously, and the available data were used, in the simulation codes, to match the transverse beam emittances of the injector to the transverse beam admittances of the booster. The phase space manipulations were accomplished by tuning a quadrupole triplet placed before the booster entrance. These simulations are intended as a supporting tool for the commissioning of the booster stage, helping the experimental determination of the working parameters and their optimization.

Neste trabalho é apresentado um estudo do espalhamento elástico e de reações nucleares dos sistemas exóticos leves 6He+9Be e 7Be+9Be. A colisão 6He+9Be foi medida nas energias de Elab = 16,2 MeV e 21,3 MeV utilizando o sistema RIBRAS (Radioactive Ion Beams in Brasil) do Instituto de Física da Universidade de São Paulo. Foram medidas distribuições angulares do espalhamento elástico, inelástico e a distribuição de partículas alfa produzidas na colisão 6He+9Be. As distribuições angulares elásticas foram analisadas por cálculos de Modelo Óptico, Canais Acoplados (CC) e Canais Acoplados com Discretização do Contínuo (CDCC). A secção de choque total de reação foi obtida da análise do espalhamento elástico. As distribuições de partículas alfa medidas foram comparadas com os resultados dos cálculos de CDCC para a quebra do projétil 6He e de CC para a quebra do alvo de 9Be e a secção de choque integrada em ângulo foi obtida. Analisamos dados do espalhamento quasielástico 7Be+9Be em Elab = 23,7 MeV que foram obtidos no laboratório CRC de Louvain-la-Neuve, na Bélgica. A distribuição angular quasielástica foi analisada primeiramente utilizando o formalismo de Modelo Óptico, o que forneceu o potencial de interação para este sistema e um fator de normalização para os dados experimentais que não foi obtido no experimento. A contribuição da excitação inelástica do núcleo 7Be na secção de choque quasielástica e a influência dos estados do contínuo no canal elástico foram investigadas por meio de cálculos de Canais Acoplados e de CDCC, respectivamente. A secção de choque total de reação 7Be+9Be foi obtida e comparada com 6He+9Be e outros sistemas da literatura. / A study of the elastic scattering and nuclear reactions in light exotic systems 6He+9Be and 7Be+9Be is presented. The 6He+9Be collision was measured at the energies Elab = 16.2 MeV and 21.3 MeV, using the RIBRAS system (Radioactive Ion Beams in Brasil) of the Institute of Physics of the University of São Paulo. Angular distributions of the elastic and inelastic scattering and the alpha-particles production in the 6He+9Be collision were measured. The elastic scattering angular distributions were analyzed by Optical Model, Coupled Channels (CC) and Continuum- Discretization Coupled-Channels (CDCC) calculations. The total reaction cross section was obtained from the elastic scattering analysis. The alpha-particle angular distributions were compared with the results of the CDCC calculations for the breakup of the 6He projectile and CC for the breakup of the 9Be target and the angle-integrated cross section have been obtained. The data for the 7Be+9Be quasielastic scattering has been measured at Elab = 23.7 MeV at CRC Radioactive Beam Facility at Louvain-la-Neuve, Belgium. The quasielastic angular distribution was analyzed firstly using the optical model formalism, which provided the potential for the 7Be+9Be interaction and a normalization factor for the experimental data that was not obtained in the experiment. The contribution of the inelastic excitation of the 7Be nucleus to quasielastic cross sections and the influence of the states of the continuum in the elastic scattering were investigated by Coupled Channels and CDCC calculations. The total reaction cross section 7Be+9Be has been obtained and compared with the 6He+9Be system and other systems of the literature.

Tanto as incubadoras como as aceleradoras são organizações especializadas no suporte de empreendimentos em fases iniciais, em especial, aqueles intensivos em inovação conhecidos como startups. Apesar da grande disseminação dessas organizações, há poucas informações na literatura que evidenciem as suas diferenças e as contribuições na jornada do empreendedorismo inovador. Assim, o objetivo principal deste estudo é comparar a diferença entre as propostas de valor das aceleradoras e das incubadoras a partir da percepção das startups que tenham sido tanto incubadas como aceleradas. Entre os objetivos específicos temos: discutir possíveis relações entre as aceleradoras e as incubadoras de negócios; apresentar a evolução das incubadoras e os fatores que induziram o surgimento das aceleradoras, descrevendo os diferentes arquétipos e as implicações que essas organizações têm no ecossistema de empreendedorismo; apresentar o cenário nacional do fenômeno de aceleração e de incubação. O levantamento de dados contará com duas etapas: análise documental de fontes de dados secundárias e estudos de caso com uso de técnica de entrevista e questionário semiestruturado. A análise documental foi feita a partir de banco de dados de artigos científicos, dados oficiais de governos, fundações, revistas e páginas web especializadas e editais de chamamento das próprias organizações. A análise documental fornecerá o retrato de como as incubadoras e as aceleradoras se promovem no ecossistema como organizações importantes no apoio às startups. Em seguida, através de abordagem exploratória descritiva e qualitativa, foram realizadas entrevistas com roteiros semiestruturados com fundadores de startups que foram incubadas e aceleradas, para compreender o valor que cada um desses processos forneceu ao desenvolvimento dessas empresas. Concluiu-se que existe uma dissonância entre o valor percebido pelas startups e o que as incubadoras e as aceleradoras promovem. Também foi possível identificar que a busca por recursos pelas startups tende a não seguir um processo linear, capturando as melhores oportunidades que estejam disponíveis no momento. Por fim, esta pesquisa é um passo exploratório para trazer novas evidências do fenômeno das startups e dos diferentes instrumentos que as constroem. Sugerem-se encaminhamentos que possam preencher lacunas na literatura a respeito dos fenômenos citados, indicando a necessidade de estudos futuros que adensem o conhecimento desse fenômeno. / Both incubators and acelerators are specialized organizations to support early-stage ventures, especially innovation-intensive ones known as startups. Despite the great spread of these organizations, there is a few information in the literature that show their differences and contributions in the journey of innovative entrepreneurship. The main objective of this study is comparing the difference between value porposition of accelerators and incubators from the perception of startups that have been both incubated and accelerated. The specific objectives are: to discuss possible relationships between accelerators and incubators; to present the evolution of the incubators and the factors that led to the emergence of the accelerators, describing the different accelerators archetypes and the implications in entrepreneurship ecosystem; to present the national scenario of acceleration and incubation. The data collection stage had two stages: documentary analysis of secondary data sources; and the case study using interview technique through semi-structured questionnaire. The documentary analysis was made from a database of scientific articles, official data from governments, foundations, journals and specialized web pages and incubators and accelerators calls for proposals. Documentary analysis provided a picture of how incubators and accelerators are promoted to the ecosystem and startups. Then, through a descriptive and qualitative exploratory approach, interviews were conducted with semistructured scripts with founders of startups that were incubated and accelerated to understand the value that each of these processes provided to the development of these companies. It was concluded that there is a dissonance between what the incubators and the accelerators promote and the value perceived by the startups, they are not being able to identify enough characteristics that distinguish them. The reason for it is the diversity of the needs and demands of the startups, different models of accelerators and incubators are formulated that, in many cases, overlap in the benefits offered. It was also possible to identify that the search for resources by startups, whether radical or disruptive startups, does not follow a linear process, capturing the best opportunities available in the ecosystem through a minimally tactical and selective approach. In order to contribute to the understanding of the growing formation of organizations supporting startups, such as incubators and accelerators, and considering the findings of this research, a tool was suggested to define the types of these organizations, loosely termed \"startup guiders\". This tool analyzes three basic dimensions: business model, value proposition and stage of intervention in the development of early-stages ventures. Finally, this research is an exploratory step in bringing new evidence of the phenomenon of startups and of the different instruments that construct them. It is suggested that there be gaps in the literature regarding the mentioned phenomena, indicating the need for future studies that increase the knowledge of this phenomenon.