Heat pipes are passive heat transfer devices in which a working fluid is sealed inside a metal enclosure. Properly designed wick structures on the inner surface of the heat pipe are critical as the wick aids in the return of the condensed liquid from the cold end back to the hot end where the vaporization-condensation cycle begins again. Additive manufacturing techniques allow for manufacturing complex parts that are typically not feasible with conventional manufacturing methods. Thus, additive manufacturing opens the possibility to develop high performance heat pipes with complex shapes. In this study, an additive manufacturing technique called Binder Jetting is used to fabricate a fully operational compact (78 mm x 48 mm x 8 mm) flat plate heat pipe. Rectangular grooves with converging cross section along the length act as the wicking structure. A converging cross section was designed to enhance the capillary force and to demonstrate the capability of additive manufacturing to manufacture complex shapes. This work describes the challenges associated with the development of heat pipes using additive manufacturing such as de-powdering and sintering. Multiple de-powdering holes and internal support pillars to improve the structural strength of the heat pipe were provided in order to overcome the manufacturing constraints. The heat pipe was experimentally characterized for thermal performance with acetone as the working fluid for two different power inputs. The heat pipe operated successfully with a 25% increase in effective thermal conductivity when compared to solid copper. / Master of Science / The number of transistors in electronic packages has been on an increasing trend in recent decades. Simultaneously there has been a push to package electronics into smaller regions. This increase in transistor density has resulted in thermal management changes of increased heat flux and localization of hotspots. Heat pipes are being used to overcome these challenges. Heat pipes are passive heat transfer devices in which a working fluid is sealed inside a metal enclosure. The fluid is vaporized at one end and condensed at the other end in order to efficiently move heat through the pipe by taking advantage of the latent heats of vaporization and condensation of the fluid. Properly designed wick structures on the inner surface of the heat pipe are used to move the condensed fluid from the cold end back to the hot end, and the wick is a critical component in a heat pipe. Additive manufacturing techniques offer the opportunity to manufacture complex parts that are typically not feasible with conventional manufacturing methods. Thus, additive manufacturing opens the possibility to develop high performance heat pipes with complex shapes as well as the ability to integrate heat exchangers with the heat source. In this study, an additive manufacturing technique called Binder Jetting is used to fabricate a fully operational compact (78 mm x 48 mm x 8 mm) flat plate heat pipe. Rectangular grooves with converging cross section along the length act as the wicking structure. This work describes the challenges associated with the development of heat pipes using additive manufacturing such as depowdering and sintering. The heat pipe was experimentally characterized for thermal performance with acetone as the working fluid for two different power inputs. The heat pipe was found to operate successfully with a 25% increase in effective thermal conductivity when compared with solid copper.

Master of Science / As parts in any device age, something inevitably breaks. When dealing with a broken metallic part, one can either replace it or repair it. Repairing is generally preferred so long as it is not too costly. Unfortunately, repairing a component is often more expensive due to the material being difficult to work with or the geometry being too intricate to fix. Additive manufacturing, commonly known as 3D printing, allows precise placement of material to build a part and has allowed the repair of complex parts. However, some materials are severely weakened using traditional additive manufacturing technologies, which melt small amounts of material and force it to cool in place quickly. To combat this, methods that do not require the material to melt could be used. Currently, these methods place a large amount of material at once, causing significant waste if the excess needs to be removed. Therefore, this work aims to create a small-scale device using a traditional milling machine. It was shown to be capable of placing small amounts of material while offering the advantage of not melting the metal. In the future, it could provide an avenue to repair previously unreachable.

Impedance-based Non-Destructive Evaluation for Additive Manufacturing (INDEAM) is rooted in the field of Structural Health Monitoring (SHM). INDEAM generalizes the structure-to-itself comparisons characteristic of the SHM process through introduction of inter-part comparisons: instead of comparing a structure to itself over time, potentially-damaged structures are compared to known-healthy reference structures. The purpose of INDEAM is to provide an alternative to conventional nondestructive evaluation (NDE) techniques for additively manufactured (AM) parts. In essence, the geometrical complexity characteristic of AM processes combined with a phase-change of the feedstock during fabrication complicate the application of conventional NDE techniques by limiting direct access for measurement probes to surfaces and permitting the introduction of internal defects that are not present in the feedstock, respectively. NDE approaches that are capable of surmounting these challenges are typically highly expensive. In the first portion of this work, the procedure for impedance-based NDE is examined in the context of INDEAM. In consideration of the additional variability inherent in inter-part comparisons - as opposed to part-to-itself comparisons - the metrics used to quantify damage or change to a structure are evaluated. Novel methods of assessing damage through impedance-based evaluation are proposed and compared to existing techniques. In the second portion of this work, the INDEAM process is applied to a wide variety of test objects. This portion considers how the sensitivity of the INDEAM process is affected by defect type, defect size, defect location, part material, and excitation frequency. Additionally, a procedure for studying the variance introduced during the process of instrumenting a structure is presented and demonstrated. / Doctor of Philosophy / Impedance-based Non-Destructive Evaluation for Additive Manufacturing (INDEAM) is a quality control approach for detecting defects in structures. As indicated by the name, impedance-based evaluation is discussed in this work in the context of qualifying additively manufactured (3D printed) structures. INDEAM fills a niche in the wider world of nondestructive evaluation techniques by providing a less expensive means to qualify structures with complex geometry. Complex geometry complicates inspection by preventing direct, physical access to all the surfaces of a part. Inspection approaches for parts with complex geometry suffuse a structure with energy and measure how the energy propagates through the structure. A prominent technique in this space is CT scanning, which measures how a structure attentuates x-rays passing through it. INDEAM uses piezoelectric materials to both vibrate a structure and measure its response, not unlike listening for the dull tone of a cracked bell. By applying voltage across a piezoelectric patch glued to a structure, the piezoelectric deforms itself and the bonded structure. By monitoring the electrical current needed to produce that voltage, the ratio of applied voltage to current draw---impedance---can be calculated, which can be thought of as a measure of how a system stores and dissipates energy. When the applied voltage oscillates near a resonant frequency of a structure (the pitch of a rung bell, for example) the structure vibrates much more intensely, and that additional movement dissipates more energy due to viscosity, friction, and transmitting sound into the air. This phenomenon is reflected in the measured impedance, so by calculating the impedance value over a large range of frequencies, it is possible to identify many resonances of the structure. So, the impedance value is tied to the vibrational properties of the structure, and the vibration of the structure is tied to its geometry and material properties. One application of this relationship is called impedance-based structural health monitoring: taking measurements of a structure when it is first built as a reference, then measuring it again later to watch for changes that indicate emerging damage. In this work, the reference measurement is established by measuring a group of control structures that are known to be free of defects. Then, every time a new part is fabricated, its impedance measurements will be compared to the reference. If it matches closely enough, it is assumed good. In both cases, impedance values don't indicate what the change is, just that there was a change. A large portion of this work is devoted to determining the types and sizes of defects that can be reliably detected through INDEAM, what effect the part material plays, and how and where the piezoelectric should be mounted to the part. The remainder of this work discusses new methods for conducting impedance-based evaluation. In particular, overcoming the extra uncertainty introduced by moving from part-to-itself structural health monitoring comparisons to the part-to-part quality control comparisons discussed in this work. A new method for mathematically comparing impedance values is introduced which involves extracting the resonant properties of the structure rather than using statistical tools on the raw impedance values. Additionally, a new method for assessing the influence of piezoelectric mounting conditions on the measured impedance values is demonstrated.

Yes / There is an increased evidence for treating hypertension by a combination of two or more drugs. Increasing the number of daily intake of tablets has been reported to negatively affect the compliance of patients. Therefore, numerous fixed dose combinations (FDCs) have been introduced to the market. However, the inherent rigid nature of FDCs does not allow the titration of the dose of each single component for an individual patient's needs. In this work, flexible dose combinations of two anti-hypertensive drugs in a single bilayer tablet with a range of doses were fabricated using dual fused deposition modelling (FDM) 3D printer. Enalapril maleate (EM) and hydrochlorothiazide (HCT) loaded filaments were produced via hot-melt extrusion (HME). Computer software was utilised to design sets of oval bi-layer tablets of individualised doses. Thermal analysis and x-ray diffractometer (XRD) indicated that HCT remained crystalline in the polymeric matrix whilst EM appeared to be in an amorphous form. The interaction between anionic EM and cationic methacrylate polymer may have contributed to a drop in the glass transition temperature (Tg) of the filament and obviated the need for a plasticiser. Across all tablet sets, the methacrylate polymeric matrix provided immediate drug release profiles. This dynamic dosing system maintained the advantages of FDCs while providing a superior flexibility of dosing range, hence offering an optimal clinical solution to hypertension therapy in a patient-centric healthcare service.

Yes / Fused deposition modelling (FDM) 3D printing has shown the most immediate potential for on-demand dose personalisation to suit particular patient's needs. However, FDM 3D printing often involves employing a relatively large molecular weight thermoplastic polymer and results in extended release pattern. It is therefore essential to fast-track drug release from the 3D printed objects. This work employed an innovative design approach of tablets with unique built-in gaps (Gaplets) with the aim of accelerating drug release. The novel tablet design is composed of 9 repeating units (blocks) connected with 3 bridges to allow the generation of 8 gaps. The impact of size of the block, the number of bridges and the spacing between different blocks was investigated. Increasing the inter-block space reduced mechanical resistance of the unit, however, tablets continued to meet pharmacopeial standards for friability. Upon introduction into gastric medium, the 1 mm spaces gaplet broke into mini-structures within 4 min and met the USP criteria of immediate release products (86.7% drug release at 30 min). Real-time ultraviolet (UV) imaging indicated that the cellulosic matrix expanded due to swelling of hydroxypropyl cellulose (HPC) upon introduction to the dissolution medium. This was followed by a steady erosion of the polymeric matrix at a rate of 8 μm/min. The design approach was more efficient than a comparison conventional formulation approach of adding disintegrants to accelerate tablet disintegration and drug release. This work provides a novel example where computer-aided design was instrumental at modifying the performance of solid dosage forms. Such an example may serve as the foundation for a new generation of dosage forms with complicated geometric structures to achieve functionality that is usually achieved by a sophisticated formulation approach.

Filament-based material extrusion additive manufacturing (MEAM) is an established technique in additive manufacturing (AM). However, semicrystalline polymers, such as polypropylene (PP), have limited commercial use in MEAM processes in the past due to their rapid crystallization kinetics and the subsequent effect on the integrity of the generated structures. The rapid crystallization of PP can be controlled by formulating blends of PP with hydrocarbon resins to enable longer re-entanglement times for interlayer adhesion. While the topic of formulating PP blends/composites with other materials to improve the printability has been investigated, variation in properties of commercial PP grades, of similar molecular weight (MW) and molecular weight distribution (MWD), on printability is still to be investigated. Those commercial PP grades can have wide variation in properties such as Melt Flow Index (MFI), additive content, and polymer architecture which can impact material properties relevant to printability. To investigate the effect of properties of commercial PP on their printability and mechanical performance, different commercial PP grades, with different properties, are blended with a fixed loading of hydrogenated resins, and the consequent effects on the mechanical properties of MEAM generated PP structures are studied via mechanical analysis. Tensile strength and the extent of interlayer adhesion in the 3D printed blends are characterized through rheological measurements. These measurements emphasize the importance of the relative location of the storage/loss modulus crossover point via small oscillatory frequency sweeps. We specifically show that a relatively higher crossover frequency will correlate with improved interlayer adhesion and reduced warpage in printed structures. However, this improvement is accompanied by a tradeoff, resulting in inferior tensile strength and an increased degree of print orientation anisotropy. / Master of Science / Additive Manufacturing (AM), commonly known as 3D printing, is a transformative technology with high potential to revolutionize the manufacturing landscape. Polymers are widely used in AM for various applications. As a result, extensive research is conducted to enhance the printability and properties of printed polymer structures. Polypropylene (PP) exhibits desirable mechanical, optical, and chemical properties that make its use in AM attractive. Despite this potential, optimizing the use of PP in 3D printing remains challenging. Consequently, extensive research is underway to improve the printability of PP. However, the effects of including additives to enhance the properties of commercial PP grades are often overlooked. We demonstrate that the choice of commercial PP grade is crucial to the mechanical and structural properties of structures generated via AM. This was established by developing a systematic experimental procedure to assess the printability of various PP grades and to measure their key mechanical and structural properties.

In recent years, there has been a growing concern over the adverse effects of traditional fossil fuels on the environment and health. Therefore, there is an increased interest in hydrogen as a fossil-free fuel source, making the need for hydrogen solutions apparent. This supports the purpose and research questions of this study, which aim to determine the suitable materials for handling hydrogen and the necessary design for structural integrity to withstand pressure. This will be achieved through additive manufacturing using polymers. The study also considers the potential of additive manufacturing for large-scale production. After conducting literature studies, polymers are of special interest due to their different structural build compared to metals. Metals do not handle hydrogen well because of the phenomenon known as hydrogen embrittlement. The preferred material properties in polymers are a crystalline structure, high density, and strong mechanical properties. The design and production are conducted using SolidWorks, with simulations of pressure and topology optimization, making it possible to create a part ready for 3-D printing after slicing. The results provide insights into the effects of parameter adjustments on the structure of the parts and the feasibility of large-scale production through additive manufacturing. By analysing the slicer program, conclusions can be made that additive manufacturing is a viable option for large-scale production, given the availability of multiple printers. However, the conclusion regarding the optimal design for handling pressurized hydrogen could not be made due to a lack of time for testing.

<p>Polymer nanocomposites are a constantly evolving material category due to the ability to engineer the mechanical, thermal, and optical properties to enhance the efficiency of a variety of systems. While a vast amount of research has focused on the physical phenomena of nanoparticles and their contribution to the improvement of such properties, the ability to implement these materials into existing commercial or newly emerging processing methods has been studied much less extensively. The primary characteristic that determines which processing technique is the most viable is the rheology or viscosity of the material. In this work, we investigate the processing methods and properties of nanocomposites for thermal interface and radiative cooling applications. The first polymer nanocomposite examined here is a two-component PDMS with graphene filler for 3D printing via a direct ink writing approach. The composite acts as a thermal interface material which can enhance cooling between a microprocessor and a heat sink by increasing the thermal conductivity of the gap. Direct ink writing requires a shear thinning ink with specific viscoelastic properties that allow for the material to yield through a nozzle as well as retain its shape without a mold following deposition. No predictive models of viscosity for nanocomposites exist; therefore, several prominent models from literature are fit with experimental data to describe the change in viscosity with the addition of filler for several different PDMS ratios. The result is an understanding of the relationship between the PDMS component ratio and graphene filler concentration with respect to viscosity, with the goal of remaining within the acceptable limits for printing via direct ink writing. The second nanocomposite system whose processability is determined is paint consisting of acrylic filled with reflective nanoparticles for radiative cooling paint applications. The paint is tested with both inkjet and screen-printing procedures with the goal of producing a thermally invisible ink. Radiative cooling paint is successfully printed for the first time with solvent modification. This work evaluates the processability of polymer nanocomposites through rheological tailoring. </p><br>

Electroactive polymers are a class of materials capable of reallocating their shape in response to an electric field while also having the ability to harvest electrical energy when the materials are mechanically deformed. Electroactive polymers can therefore be used as sensors, actuators, and energy harvesters. The parameters for manufacturing flexible electroactive polymers are complex and rate limiting due to number of steps, their necessity, and time intensity of each step. Successful additive manufacturing processes for electroactive polymers will allow for scalability and flexibility beyond current limitations, advancing the field, opening additional manufacturing possibilities, and increasing output. The goal for this research was to use additive manufacturing techniques to print conductive and dielectric substrates for building flexible circuits and sensors. Printing flexible conductive layers and substrates together allows for added creativity in design and application.

WAAM is a relatively unexplored additive manufacturing method. Although research in this area has been performed for some years and the hardware is relatively cheap, the method is not widely used. As the name suggest, it uses wire and an arc welding equipment to deposit beads on top of each other to create a geometry. As WAAM is a near net-shape method, the parts must be machined to its net-shape after the beads has been deposited. BAE Systems Hägglunds AB are investigating the use of WAAM in an industrial robot cell and this Master’s thesis has been written with the purpose of enabling the use of WAAM for manufacturing parts at the company. This report investigates how a part is prepared for WAAM and near net-shape machining. A formula for approximating the cost of manufacturing a part is investigated. A software for slicing a .STL file for generating a toolpath is developed in Matlab. The software then exports the toolpath to a code that the robot can read. It can also generate a digital model of the work piece for net-shape machining through CATIA macro. A model for calculating the cost of using the WAAM-cell once the toolpath for a part is known is presented. The investigated areas and the developed software are then applied to a part, and the results of the report is discussed.