Este trabalho está inserido em um projeto que procura estudar a viabilidade técnica da aplicação de um relativamente novo conceito de tratamento térmico, chamado de Têmpera e Partição (T&P), como alternativa para o processamento de ferros fundidos nodulares com alta resistência mecânica. O processo T&P tem por objetivo a obtenção de microestruturas multifásicas constituídas de martensita e austenita retida, estabilizada em carbono. A martensita confere elevada resistência mecânica, enquanto a austenita confere ductilidade. No processo T&P, após a austenitização total ou parcial da liga, o material é temperado até uma temperatura de têmpera TT entre as temperaturas Ms e Mf para produzir uma mistura controlada de martensita e austenita. Em seguida, na etapa de partição, o material é mantido isotermicamente em uma temperatura igual ou mais elevada (denominada temperatura de partição TP) para permitir a partição de carbono da martensita para a austenita. O carbono em solução sólida diminui a temperatura Ms da austenita, estabilizando-a à temperatura ambiente. O presente trabalho procurou estudar aspectos de transformações de fases -- com ênfase na evolução microestrutural e cinética das reações -- do tratamento térmico de Têmpera e Partição (T&P) aplicado a uma liga de ferro fundido nodular (Fe-3,47%C-2,47%Si-0,2%Mn). Tratamentos térmicos consistiram de austenitização a 880 oC por 30 min, seguido de têmpera a 140, 170 e 200 oC e partição a 300, 375 e 450 oC por até 2 h. A caracterização microestrutural foi feita por microscopia óptica (MO), eletrônica de varredura (MEV), difração de elétrons retroespalhados (EBSD) e análise de microssonda eletrônica (EPMA). A análise cinética foi feita por meio de ensaios de dilatometria de alta resolução e difração de raios X in situ usando radiação síncrotron. Resultados mostram que a ocorrência de reações competitivas -- reação bainítica e precipitação de carbonetos na martensita -- é inevitável durante a aplicação do tratamento T&P à presente liga de ferro fundido nodular. A cinética da reação bainítica é acelerada pela presença da martensita formada na etapa de têmpera. A reação bainítica acontece, a baixas temperaturas, desacompanhada da precipitação de carbonetos e contribui para o enriquecimento em carbono, e consequente estabilização, da austenita. Devido à precipitação de carbonetos na martensita, a formação de ferrita bainítica é o principal mecanismo de enriquecimento em carbono da austenita. A microssegregação proveniente da etapa de solidificação permanece no material tratado termicamente e afeta a distribuição da martensita formada na etapa de têmpera e a cinética da reação bainítica. Em regiões correspondentes a contornos de célula eutética são observadas menores quantidades de martensita e a reação bainítica é mais lenta. A microestrutura final produzida pelo tratamento T&P aplicado ao ferro fundido consiste de martensita revenida com carbonetos, ferrita banítica e austenita enriquecida estabilizada pelo carbono. Adicionalmente, foi desenvolvido um modelo computacional que calcula a redistribuição local de carbono durante a etapa de partição do tratamento T&P, assumindo os efeitos da precipitação de do crescimento de placas de ferrita bainítica a partir da austenita. O modelo mostrou que a cinética de partição de carbono da martensita para a austenita é mais lenta quando os carbonetos precipitados são mais estáveis e que, quando a energia livre dos carbonetos é suficientemente baixa, o fluxo de carbono acontece da austenita para a martensita. A aplicação do modelo não se limita às condições estudadas neste trabalho e pode ser aplicada para o planejamento de tratamentos T&P para aços. / The present work belongs to a bigger project whose main goal is to study the technical feasibility of the application of a relatively new heat treating concept, called Quenching and Partitioning (Q&P), as an alternative to the processing of high strength ductile cast irons. The aim of the Q&P process is to obtain multiphase microstructures consisting of martensite and carbon enriched retained austenite. Martensite confers high strength, whereas austenite confers ductility. In the Q&P process, after total or partial austenitization of the alloy, the material is quenched in a quenching temperature TQ between the Ms and Mf temperatures to produce a controlled mixture of martensite and austenite. Next, at the partitioning step, the material is isothermally held at a either equal or higher temperature (so called partitioning temperature TP) in order to promote the carbon diffusion (partitioning) from martensite to austenite. The present work focus on the study of phase transformations aspects -- with emphasis on the microstructural evolution and kinetics of the reactions -- of the Q&P process applied to a ductile cast iron alloy (Fe-3,47%C-2,47%Si-0,2%Mn). Heat treatments consisted of austenitization at 880 oC for 30 min, followed by quenching at 140, 170, and 200 oC and partitioning at 300, 375 e 450 oC up to 2 h. The microstructural characterization was carried out by optical microscopy (OM), scanning electron microscopy (SEM), backscattered diffraction (EBSD), and electron probe microanalysis (EPMA). The kinetic analysis was studied by high resolution dilatometry tests and in situ X-ray diffraction using a synchrotron light source. Results showed that competitive reactions -- bainite reaction and carbides precipitation in martensite -- is unavoidable during the Q&P process. The bainite reaction kinetics is accelerated by the presence of martensite formed in the quenching step. The bainite reaction occurs at low temperatures without carbides precipitation and contributes to the carbon enrichment of austenite and its stabilization. Due to carbides precipitation in martensite, growth of bainitic ferrite is the main mechanism of carbon enrichment of austenite. Microsegregation inherited from the casting process is present in the heat treated material and affects the martensite distribution and the kinetics of the bainite reaction. In regions corresponding to eutectic cell boundaries less martensite is observed and the kinetics of bainite reaction is slower. The final microestructure produced by the Q&P process applied to the ductile cast iron consists of tempered martensite with carbides, bainitic ferrite, and carbon enriched austenite. Additionally, a computational model was developed to calculate the local kinetics of carbon redistribution during the partitioning step, considering the effects of carbides precipitation and bainite reaction. The model showed that the kinetics of carbon partitioning from martensite to austenite is slower when the tempering carbides are more stable and that, when the carbides free energy is sufficiently low, the carbon diffuses from austenite to martensite. The model is not limited to the studied conditions and can be applied to the development of Q&P heat treatments to steels.

The Quenching and Partitioning (Q&P) heat treatment has been proposed in the early 2000s to produce cold-rolled sheets combining high-strength and formability for the automotive market. Q&P consists, first, of an interrupted quench between the martensite-start temperature (Ms) and the martensite-finish temperature (Mf) from intercritical annealing or full austenitization in order to form controlled fractions of martensite. This is followed by a partitioning step in order to stabilize the untransformed austenite through carbon enrichment. In order to maximize the carbon transfer from martensite to austenite, the use of specific alloying elements and the design of appropriate Q&P parameters are required to eliminate or minimize competing phenomena such as carbide formation and austenite decomposition. The final quenched and partitioned microstructure, using full austenitization, ideally consists of carbon-depleted lath martensite and significant fractions of retained austenite providing an improved combination of strength and ductility. Hence, the transformation of retained austenite upon straining at room temperature (TRIP effect) provides supplementary work-hardening and eventually improves the ductility. In the present work, Quenching and Partitioning (Q & P) heat treatments were carried out in a quench dilatometeron a 0.2 wt% carbon steel. The microstructure evolution of the Q & P steels was characterized usingdilatometry, SEM, EBSD and XRD. The martensitic transformation profile was analyzed in order to estimate thefraction of martensite formed at a given temperature below the martensite start temperature Ms. Q & P wasshown to be an effective way to stabilize retained austenite at room temperature. However, the measuredaustenite fractions after Q & P treatments showed significant differences when compared to the calculated valuesconsidering ideal partitioning conditions. Indeed, the measured austenite fractions were found to be less sensitiveto the quench temperature and were never larger than the ideal predicted maximum fraction. Competitivereactions such as austenite decomposition into bainite and carbide precipitation were found to occur in thepresent work.Furthermore, a broad range of mechanical properties was obtained when varying the quenching temperaturesand partitioning times. The direct contributions between Q & P microstructural constituents -such as retainedaustenite as well as tempered/fresh martensite- and resulting mechanical properties were scrutinized. This wascritically discussed and compared to quenching and austempering (QAT) which is a more conventional processingroute of stabilizing retained austenite at room temperature. Finally, Q & P steels were shown to exhibit aninteresting balance between strength and ductility. The achievement of this interesting combination of mechanicalproperties was reached for much shorter processing times compared to QAT steels. / Doctorat en Sciences de l'ingénieur et technologie / info:eu-repo/semantics/nonPublished

The ductility of Q&P 1180 steel was studied with regard to retained austenite transformation under different strain paths. Specimens were tested in uniaxial tension in a standard test frame as well as in situ in the scanning electron microscope (SEM). Then digital image correlation (DIC) was used to compute the effective strain at the level of the individual phases in the microstructure. Stretching experiments were also performed using limiting dome height (LDH) tooling, where specimens were strained in both biaxial and plane strain tension. The experiments were done incrementally, for each strain path, and the retained austenite at each level of strain was measured using electron backscatter diffraction (EBSD). Retained austenite levels in the uniaxial tension case dropped from an initial measured level of about 8% to about 2% during an initial strain increment of 0.02, but then stabilized as the specimen was strained to 0.1. In the plane strain and biaxial tension cases retained austenite also dropped significantly during an initial strain increment of about 0.04, but then continued to decrease as the specimens were strained to failure. Biaxial tension, in particular, was the most effective strain path for transforming retained austenite to martensite, resulting in a final volume fraction of 0.3% at an effective strain of 0.3. Retained austenite in the plane-strain tension case dropped at a faster rate than in the biaxial tension case, but finished at about 1% at a strain of 0.1. The greatest limit strains were seen in the biaxial tension case, which may be partly explained by the more effective conversion of retained austenite than was seen in the uniaxial tension case.

Good toughness properties in base and weld material enable the use of duplex stainless steels (DSS) in critical applications. DSS offer high strength compared to common austenitic stainless steels. The high strength can be utilized to reduce the wall thickness and accordingly accomplish reduction of cost, welding time and transportation weight, contributing to ecological and energy savings. Although DSS have been used successfully in many applications the last decades, the full utilisation in pressure vessels has been restricted due to conservative design rules. The consequences of failure in a pressure vessel are often very severe and it is accordingly important to verify a high ductility and fracture toughness. In this study fracture toughness data has been generated that has been used to analyse the brittle failure model in the European pressure vessel code EN 13445. The evaluation of the results has been made successfully by the master curve analysis, previously applied to ferritic steels. The master curve analysis includes calculation of a reference temperature, which can be correlated to an impact toughness transition temperature. A correlation between fracture and impact toughness results is necessary for a practically applicable design code. The heat distribution and austenite reformation have been modelled to verify satisfactory toughness properties in the heat affected zone. A similar model was used to evaluate the nucleation and diffusional growth of sigma phase during isothermal heat treatment or continuous cooling. For future stainless steel development, the availability of satisfactory correlations between composition, microstructure and mechanical properties are essential to optimize alloy design. Stainless steel data has been analysed to find approximate relations between mechanical properties and the chemical composition, grain size, ferrite content, product thickness and solution hardening size misfit parameter. The solution hardening effect was successfully predicted by the Labusch-Nabarro relation and multiple regression analyses were used to evaluate hardening equations for stainless steel. / QC 20100920

The use of pre-hardened mold steels has increased appreciably over the years; more than 80% of the plastic mold steels are used in pre-hardened condition. These steels are delivered to the customer in finished state i.e. there is no need of any post treatment. With hardness around ~40HRC, they have properties such as good polishability, good weldability, corrosion resistance and thermal conductivity. Machinability is a very important parameter in pre-hardened mold steels as it has a direct impact on the cost of the mold. In normal machining operations involving intricate or near net shapes, machining constitutes around 60% of the total mold cost. Efforts are underway to explore every possible way to reduce costs associated with machining and to make production more economical. All the possible parameters which are considered to affect the machinability are being investigated by the researchers. This thesis work focuses on the effect of prior austenite grain size on the machinability of pre-hardened mold steel (Uddeholm Nimax).  Austenitizing temperatures and holding times were varied to obtain varying grain sized microstructures in different samples of the same material. As it was difficult to delineate prior-austenite grain boundaries, experimental and empirical methods were employed to obtain reference values. These different grain sized samples were thereafter subjected to machining tests, using two sets of cutting parameters. Maximum flank wear depth=0.2mm was defined for one series of test which were more akin to rough machining, and machining length of 43200mm or maximum wear depth=0.2mm were defined for second series of tests which were similar to finishing machining. The results were obtained after careful quantative and qualitative analysis of cutting tools. The results obtained for Uddeholm Nimax seemed to indicate that larger grain sized material was easier to machine. However, factors such as retained austenite content and work hardening on machined surface, which lead to degradation of machining operations were also taken into consideration. Uddeholm Nimax showed better machinability in large grained samples as retained austenite(less than 2%) content was minimal in the large grained sample. Small grained sample in Uddeholm Nimax had a higher retained austenite (7+2%) which resulted in degradation of machining operation and a lesser cutting tool life.

A new technique based on the study of the transmitted neutron beam has been developed to study the low-temperature decomposition of austenite in a 0.4 wt.% C–3 wt.% Mn–2 wt.% Si steel. Experiments were conducted in which the neutron beam continuously passed through a specially designed layered sample, the temperature of which could be controlled to allow for a high-temperature austenization treatment followed by accelerated cooling to an isothermal transformation temperature in the range of 275–450 °C. It was possible to measure the volume fraction of the face-centred cubic (fcc) and body-centred cubic (bcc) phases and the carbon concentration of the fcc phase by characterizing the neutron Bragg edges in the transmitted beam. This provides a technique for in situ continuous measurements on the decomposition of austentite. The technique has been validated by comparing the data with other experimental techniques such as dilatometry, quantitative optical metallography and room temperature X-ray diffraction.

Transformation-induced plasticity (TRIP) steels have excellent strength, ductility and work hardening behaviour, which can be attributed to a phenomenon known as the TRIP effect. The TRIP effect involves a metastable phase, retained austenite (RA), transforming into martensite as a result of applied stress or strain. This transformation absorbs energy and improves the work hardening rate of the steel, delaying the onset of necking. This work describes two distinct TRIP steel microstructures and focuses on how microstructure affects the RA-to-martensite transformation and the uniaxial tensile behaviour. A two-step heat treatment was applied to an aluminum-alloyed TRIP steel to obtain a microstructure consisting of equiaxed grains of ferrite surrounded by bainite, martensite and RA -- the equiaxed microstructure. The second microstructure was produced by first austenitizing and quenching the steel to produce martensite, followed by the two-step heat treatment. The resulting microstructure (labelled the lamellar microstructure) consisted of elongated grains of ferrite with bainite, martensite and RA grains. Both microstructural variants had similar initial volume fractions of RA. A series of interrupted tensile tests and ex-situ magnetic measurements were conducted to examine the RA transformation during uniform elongation. Similar tests were also conducted on an equiaxed microstructure and a lamellar microstructure with similar ultimate tensile strengths. Results show that the work hardening rate is directly related to the RA transformation rate. The slower transformation rate, or higher RA stability, that was observed in the lamellar microstructure enables sustained work hardening at high strains. In contrast, the equiaxed microstructure has a lower RA stability and thus exhibits high values of work hardening at low strains, but the effect is quickly exhausted. Several microstructural factors that affect RA stability were examined, including RA grain size, aspect ratio, carbon content and spatial distribution of the phases. Two of these factors were characteristic of only the lamellar microstructures and led to higher RA stabilities: elongated RA grains and RA grains being primarily surrounded by bainite. The results were also compared with previous work on a silicon-alloyed TRIP steel to show that the aluminum-alloyed compositions could achieve similar, if not better, combinations of strength and ductility. / Thesis (Master, Mechanical and Materials Engineering) -- Queen's University, 2012-09-24 16:52:28.032

No description available.

No description available.

The phenomenon of hydrogen embrittlement in steel has been known for over 150 years. Hydrogen-resistant alloys have been developed to mitigate this effect and three types of alloys with optimised structures have been enhanced over the years: nickel alloys, stainless steels, and quenched and tempered martensitic low alloy steels. Nevertheless, those alloys are limited in terms of strength and ductility. The aim of the work presented in this thesis was to design bainitic alloys with hydrogen embrittlement resistance, and with a better combination of strength and ductility than conventional alloys. In the novel alloys, two microstructural features were produced to mitigate the damaging effects of hydrogen: 1. A percolating austenite structure, in which hydrogen diffusion is orders of magnitude lower than in bainitic ferrite. This feature was introduced to impede the ingress of hydrogen through the structure. 2. Iron carbide traps, which can form at the bainite transformation temperature. This feature was introduced to trap diffusible hydrogen and prevent it from causing damage. The alloys, designed with the aid of computer models and phase transformation theory, contained a volume fraction of retained austenite above its percolation threshold, theorised as 0.1, which was proven to form an effcient barrier to hydrogen ingress. The effective diffusivity of hydrogen, measured using an electrochemical permeation technique, was shown to decrease with increasing austenite fraction up to the percolation threshold. It was seen to plateau for austenite fractions comprised between 0.1 and 0.18, and to decrease further for fractions above 0.18. The compositions of the alloys were precisely selected to allow for iron carbides to precipitate during the bainitic transformation reaction. Until the present work, only alloy carbides V4C3, TiC and NbC had been reported to strongly trap hydrogen. The literature was very inconsistent regarding the trapping ability of cementite, with reported trap binding energies ranging from 11 to 66 kJ mol−1. The carbides produced in the alloys were identified as cementite. The cementite fraction was measured to be 0.001 ± 0.0001 for one of the designed alloys, which is the lowest ever reported carbide fraction in steel measured using a simple X-ray diffraction technique. Experimental thermal desorption spectroscopy data were used to determine the binding energy of hydrogen to cementite to be 37.5 kJ mol−1, suggesting that cementite is not a strong hydrogen trap. Further tests performed after room temperature hydrogen degassing displayed insignifcant amount of trapped hydrogen, thus confrming the reversible nature of cementite traps. The comparison of two successive transients using the electrochemical permeation technique confirmed that result. The influence of the heat treatments on the microstructures and on the mechanical properties of the designed alloys was extensively studied. The novel alloys met all the set requirements, and successfully outperformed conventional alloys in terms of strength and ductility. They did not meet the NACE TM0316-2016 standard requirement for operation in hydrogen-rich environments, likely owing to the inadequate trapping ability of cementite. Future work should focus on exploring the possible use of alternative carbides for hydrogen trapping in bainitic structures.