11 |
Novel Low-Complexity SLM Schemes for PAPR Reduction in OFDMA Uplink SystemsXie, Jia-Cheng 10 August 2008 (has links)
One of the major drawbacks of multi-carrier systems is the high peak-to-average power ratio (PAPR) of the transmitted signals. In this paper, the proposed novel low-complexity selective mapping (SLM) schemes are applicable to interleaved-4 orthogonal frequency division multiple access (OFDMA) uplink systems for PAPR reduction. The novel scheme just needs one inverse fast Fourier transform (IFFT) block because that the phases of the transmitted signals in frequency domain are rotated by circular convolution with conversion vectors in time domain. Moreover, a special set of conversion vectors are proposed in novel scheme, which are not only computed with low complexity but also reduce the PAPR effectively. In proposed scheme, different conversion vectors and appropriate subcarriers mapping are picked up for different users. The scheme supplies a practicable low-complexity method for PAPR reduction in interleaved-4 OFDMA uplink systems. Besides, the bit error rate (BER) performance is as good as the SLM scheme.
|
12 |
Kariūnų blauzdą tiesiančių ir lenkiančių raumenų nuovargio ir atsigavimo dinamika / Dynamics of tiredness and recuperation of cadets’ shank extensor and flexor muscleBaranauskienė, Kristina 16 August 2007 (has links)
Darbo objektas – kariūnų blauzdą tiesiančių ir lenkiančių raumenų funkcinių ypatybių nustatymas ir palyginimas metų eigoje. Tikslas – nustatyti, kaip pasikeičia kariūnų blauzdos raumenų funkcinės ypatybės per 6 mėnesių trukmės fizinio rengimo ciklą. Uždaviniai: 1. Nustatyti blauzdą tiesiančių ir lenkiančių raumenų susitraukimo vidutinį galingumą, maksimalią jėgą, susitraukimo kampą, nuovargį ir atsigavimo kaitą. 2. Palyginti blauzdos raumenų nuovargio ir atsigavimo skirtumą, tarp pirmojo ir antrojo testavimo, esant dinaminiam raumens susitraukimui. Hipotezė - manome, kad atliekant antrąjį testavimą kariūnai po 6 mėn. studijų turi būti fiziškai pajėgesni, labiau turi pasireikšti blauzdą tiesiančių ir lenkiančių raumenų nuovargis ir atsigavimas. Išvados: 1. Abiejų testavimų metu blauzdą tiesiančių ir lenkiančių raumenų susitraukimo vidutinė galia krūvio metu sumažėjo, o praėjus 5 min. po krūvio atsigavo. 2. Blauzdą tiesiančių raumenų maksimali jėga bei atliktas darbas I-ojo testavimo metu yra didesnis negu blauzdą lenkiančių raumenų, tačiau II-ojo testavimo metu pastebimas didesnis nuovargis abiejų raumenų. 3. Blauzdą tiesiančių raumenų maksimalios jėgos kampas abiejų testavimų metu yra vienodas, tačiau blauzdą lenkiančių raumenų II-ojo testavimo metu yra didesnis. 4. Pastebimas ryškus blauzdos raumenų atsigavimas abiejų testavimų metu. / Object of this work – to determine function features of cadets’ shank straighten and bend muscle and to make comparison in the course of year. Aim – to find out how function features of cadets’ shank muscle are changing during 6 months physical training period. Tasks: 1. To establish contraction average power, maximum power, peak torque, tiredness and recuperation alternation of shank straighten and bend muscle. 2. To compare the difference between 1st and 2nd test of shank muscle tiredness and recuperation when there is dynamic contraction of the muscle Hypothesis – it is thought that during 2nd test after 6 months cadets should have more physical power, there should be displayed more intense tiredness and recuperation of shank straighten and bend muscle. Conclusions: 1. During 1st and 2nd test muscle contraction average power in the course of strain has decreased and after 5 min. it has recuperated. 2. Maximum power of shank straighten muscle and work done during the 1st test is bigger than of bend muscle, but during 2nd test there is seen larger tiredness of both muscle. 3. Peak torque of shank straighten muscle during both tests is the same, but peak torque of shank bend muscle is bigger during the 2nd test. 4. There is seen a distinct shank muscle recuperation during both test.
|
13 |
Optimizing LDPC codes for a mobile WiMAX system with a saturated transmission amplifierSalmon, Brian Paxton 26 January 2009 (has links)
In mobile communication, the user’s information is transmitted through a wireless communication link that is subjected to a range of deteriorating effects. The quality of the transmission can be presented by the rate of transfer and the reliability of the received stream. The capacity of the communication link can be reached through the use of channel coding. Channel coding is the method of adding redundant information to the user’s information to mitigate the deteriorating effects of the communication link. Mobile WiMAX is a technology that makes use of orthogonal frequency division multiplexing (OFDM) modulation to transmit information over a wireless communication channel. The OFDM physical layer has a high peak average to power ratio (PAPR) characteristic that saturates the transmitter’s amplifier quite easily when proper backoff is not made in the transmission power. In this dissertation an optimized graph code was used as an alternative solution to improve the system’s performance in the presence of a saturated transmission’s amplifier. The graph code was derived from a degree distribution given by the density evolution algorithm and provided no extra network overhead to implement. The performance analysis resulted in a factor of 10 improvement in the error floor and a coding gain of 1.5 dB. This was all accomplished with impairments provided by the mobile WiMAX standard in the construction of the graph code. / Dissertation (MEng)--University of Pretoria, 2009. / Electrical, Electronic and Computer Engineering / unrestricted
|
14 |
Performance enhancement of OFDM-Based systems using Nyquist-I pulsesArraño Scharager, Hernán Felipe January 2015 (has links)
Ingeniero Civil Eléctrico / Los constantes y cada vez más acelerados avances tecnológicos, han generado que los sistemas de comunicación se optimicen considerablemente con el transcurso de los años. Dentro de los cambios más importantes que se han visto en el último tiempo, destaca la disminución del uso de los clásicos sistemas de telecomunicaciones basados en portadoras únicas, dándose paso a sistemas más complejos en donde la información se transmite utilizando múltiples portadoras. Dentro de este último grupo de técnicas, uno de los que más sobresale es orthogonal frequency division multiplexing (OFDM), el cual ha sido y es, ampliamente utilizado en múltiples aplicaciones o estándares de comunicación. El uso extensivo de OFDM se debe a varias ventajas que esta técnica posee, tales como: alcanzar altas tasas de transmisión de datos, generar señales robustas ante canales inalámbricos, tener una alta eficiencia espectral, entre otros. Pero, aun cuando éstos exhiben múltiples ventajas, también presentan ciertos inconvenientes que deben ser tratados como lo son: los altos niveles de peak-to-average power ratio (PAPR) que caracterizan a las señales OFDM y la sensibilidad a errores originados por la desincronización entre el transmisor y receptor. Esto último, facilita la generación de interferencia entre portadoras (inter-carrier interference, ICI) y, por ende, un aumento en la probabilidad de error.
En este trabajo se examina el funcionamiento de los sistemas basados en OFDM, partiendo desde la generación de la señal, hasta su comportamiento espectral. Pero por otro lado, también se analiza como la implementación de pulsos que cumplen con el primer criterio de Nyquist (Nyquist-I), favorece al rendimiento de esta clase de sistemas. El uso de pulsos Nyquist-I para combatir los inconvenientes típicos mostrados por los sistemas basados en OFDM ha sido propuesto por múltiples investigadores. En este trabajo se estudia en detalle una nueva familia de pulsos Nyquist-I llamada improved parametric linear combination pulses (IPLCP), la cual se propone para combatir un completo listado de aspectos perjudiciales mostrados por sistemas OFDM reales, a diferencia de otros pulsos que solamente buscan solucionar uno de ellos. Para analizar el rendimiento de la nueva familia de pulsos, se le compara con otras ya conocidas en términos del ICI, la razón señal a interferencia (signal-to-interference ratio, SIR), el PAPR y la tasa de probabilidad de error de bit (bit error rate, BER). Finalmente, el análisis demuestra que la nueva familia es la que mejor se desempeña en promedio en términos de los parámetros de estudio recién mencionados, dejando en claro que la implementación del IPLCP favorece al rendimiento de los sistemas de comunicación basados en la tecnología OFDM.
|
15 |
AC Power Combining Strategy with Application to Efficient Linear Power AmplifiersBendig, Rudi Matthew 01 June 2014 (has links)
With the ongoing push for wireless systems to accommodate more users and support higher data rates more efficient modulation schemes have been created that are more advanced than simple FM and AM modulation used for radio broadcasting. These modulation schemes, such as orthogonal frequency division multiplexing (OFDM), suffer from high peak to average power ratios. Standard Class A and Class AB amplifiers cannot simultaneously achieve good linearity and efficiency, and therefore there has been an increase in the development of new topologies to combat this issue. Common features to these circuits is power combining of two or more separate transistors.
In this work, we consider various ways of two-source power combining and identify four topologies of interest. We notice that linear power-efficient amplifiers reported to date are based upon two of the identified combining strategies. We believe that no amplifiers have been reported that leverage the other two alternatives. This work produces a fully-functional amplifier based on one of these alternatives. The prototypes are intended to serve as concept verification of the architecture and hence are implemented at lower (1 MHz) frequencies.
|
16 |
Design and Implementation of a Constant Envelope OFDM Waveform in a Software-Defined Radio PlatformAjo Jr, Amos V. 30 June 2016 (has links)
This thesis examines the high peak-to-average-power ratio (PAPR) problem of OFDM and other spectrally-efficient multicarrier modulation schemes, specifically their stringent requirements for highly linear, power-inefficient amplification. The thesis then presents a most intriguing answer to the PAPR-problem in the form of a constant-envelope OFDM (CE-OFDM) waveform, a waveform which employs phase modulation to transform the high-PAPR OFDM signal into a constant envelope signal, like FSK or GMSK, which can be amplified with non-linear power amplifiers at near saturation levels of efficiency. A brief analytical description of CE-OFDM and its suboptimal receiver architecture is provided in order to define and analyze the key parameters of the waveform and their performance impacts.
The primary contribution of this thesis is a highly tunable software-defined radio (SDR) implementation of the waveform which enables rapid-prototyping and testing of CE-OFDM systems. The digital baseband processing of the waveform is executed on a general purpose processor (GPP) in the Linux Ubuntu 14.04 operating system, and programmed using the GNU Radio SDR software framework with a mixture of Python and C++ routines. A detailed description of the software implementation is provided, and baseband simulations of the SDR CE-OFDM receiver in additive white Gaussian noise (AWGN) validate the performance of the implemented signal processing.
A fully-functional CE-OFDM radio system is proposed in which GPPs executing the software defined transmitter and receiver routines are interfaced with Ettus Universal Software Radio Peripheral (USRP) transceiver front ends. A software testbench is created to enable rapid configuration and testing of the CE-OFDM waveform over all permutations of its parameters, over both simulated and physical RF channels, to draw deeper insights into the characteristics of the waveform and the necessary design considerations and improvements for further development and deployment of CE-OFDM systems. / Master of Science
|
17 |
High efficiency S-Band vector power modulator design using GaN technology / Conception d’un modulateur vectoriel de puissance à haut rendement, bande S, en technologie GaNDasgupta, Abhijeet 27 April 2018 (has links)
L’évolution des systèmes de télécommunications, liée à une demande sans cesse croissante en termes de débit et de volume de données, se concrétise par le développement de systèmes proposant des bandes passantes très larges, des modulations à très hautes efficacités spectrales, de la flexibilité en puissance et en fréquence d’émission. Par ailleurs, la mise en œuvre de ces dispositifs doit se faire avec un souci permanent d’économie d’énergie d’où la problématique récurrente de l’amplification de puissance RF qui consiste à allier au mieux rendement, linéarité et bande passante. L’architecture conventionnelle d’une chaine d’émission RF consiste dans une première étape à réaliser l’opération de modulation-conversion de fréquence (Modulateur IQ) puis dans une deuxième étape l’opération de conversion d’énergie DC-RF (Amplificateur de Puissance), ces deux étapes étant traditionnellement traitées de manière indépendante. L’objectif de ces travaux de thèse est de proposer une approche alternative qui consiste à combiner ces deux opérations dans une seule et même fonction : le modulateur vectoriel de puissance à haute efficacité énergétique. Le cœur du dispositif, conçu en technologie GaN, repose sur un circuit à deux étages de transistors HEMT permettant d’obtenir un gain en puissance variable en régime de saturation. Il est associé à un modulateur de polarisation multi-niveaux spécifique également en technologie GaN. Le dispositif réalisé a permis de générer directement, à une fréquence de 2.5 GHz, une modulation vectorielle 16QAM (100Msymb/s) de puissance moyenne 13 W, de puissance crête 25W avec un rendement global de 40% et une linéarité mesurée par un EVM à 5%. / The evolution of telecommunications systems, linked to a constantly increasing demand in terms of data rate and volume, leads to the development of systems offering very wide bandwidths, modulations with very high spectral efficiencies, increased power and frequency flexibilities in transmitters. Moreover, the implementation of such systems must be done with a permanent concern for energy saving, hence the recurring goal of the RF power amplification which is to combine the best efficiency, linearity and bandwidth. Conventional architectures of RF emitter front-ends consist in a first step in performing the frequency modulation-conversion operation (IQ Modulator) and then in a second step the DC-RF energy conversion operation (Power Amplifier), these two steps being usually managed independently. The aim of this thesis is to propose an alternative approach that consists in combining these two operations in only one function: a high efficiency vector power modulator. The core of the proposed system is based on a two-stage GaN HEMT circuit to obtain a variable power gain operating at saturation. It is associated with a specific multi-level bias modulator also design using GaN technology. The fabricated device generates, at a frequency of 2.5 GHz, a 16QAM modulation (100Msymb/s) with 13W average power, 25W peak power, with an overall efficiency of 40% and 5% EVM.
|
18 |
Simulation and evaluation of a DVB System using Simulink (Vol. II)Prieto, Alberto Pastor January 2005 (has links)
<p>DVB (Digital Video Broadcasting) is the television digital system. It's however much more than a simple replacement for existing analogue television transmission, this system has many advantages such as picture quality and allows you a range of new features and services including subtitling, multiple audio tracks, interactive content, multimedia content. </p><p>The system is based in the OFDM technology, which allows DVB system to exploit the spectrum frequencies in a better way, saving spectrum, but OFDM has an important drawback that is the peak to average power ratio problem. OFDM is based on the FFT algorithms generating orthogonal subcarriers. </p><p>This thesis talks about the improvement of the PAPR problem using the soft compression method. </p><p>The simulation has been developed in Simulink® and Matlab®. With all the information presented in this thesis, any user can simulate the system. Thus, this thesis can be improved using other techniques to solve the PAPR problem.</p>
|
19 |
Simulation and evaluation of a DVB System using Simulink (Vol. II)Prieto, Alberto Pastor January 2005 (has links)
DVB (Digital Video Broadcasting) is the television digital system. It's however much more than a simple replacement for existing analogue television transmission, this system has many advantages such as picture quality and allows you a range of new features and services including subtitling, multiple audio tracks, interactive content, multimedia content. The system is based in the OFDM technology, which allows DVB system to exploit the spectrum frequencies in a better way, saving spectrum, but OFDM has an important drawback that is the peak to average power ratio problem. OFDM is based on the FFT algorithms generating orthogonal subcarriers. This thesis talks about the improvement of the PAPR problem using the soft compression method. The simulation has been developed in Simulink® and Matlab®. With all the information presented in this thesis, any user can simulate the system. Thus, this thesis can be improved using other techniques to solve the PAPR problem.
|
20 |
PAPR Reduction Schemes Based on Spreading Code Combination and Subcarrier Scrambling for MC-CDMA SystemsLee, Ming-Kai 23 August 2011 (has links)
In order to improve the drawback of the high peak-to-average power ratio (PAPR) on the multi-carrier systems, in this paper we derive a statistical characterization approach of the time domain signal power variance metric by means of every user¡¦s spreading code combination and subcarrier scrambling. We obviously reduce the PAPR on the multi-carrier code division multiple access (MC-CDMA) systems by resorting the combination of spreading codes and scrambling the polarities of subcarriers. Due to the large calculative number of exhaustive search, we use a low complexity Replacement Search Method (RSM) to reduce the calculation times of searching, and obtain a good result. Moreover, we can get a better PAPR reduction performance by increasing the number of iteration.
|
Page generated in 0.1066 seconds