No description available.

This paper introduces a high-gain, low-noise band-pass filter system for detection/amplification of small signals. In addition, related theory and methodology are described for a specific design implementation. Simulation and experimental results are presented and discussed. The purpose of the implemented design was to construct a band-pass filter system with 102 dB gain and with an output noise level of less than 0.8V. The design of the high-gain band-pass filter system was achieved mainly with the help of Filter Pro, LTSpice IV, and Multisim 12. The thesis provides important support for the project Marker Locator and constitutes a valuable reference for future active filter system design and small signal detection/amplification. / Marker Locator

This work is aimed at an analysis of frequency demodulation, design, simulation, and construction of a coincidence demodulator. Chapter 1 explains the basic characteristics of frequency modulated (FM) signals and provides an overview of the required signal bandwidth, the signal spectrum, and the signal-to-noise ratio after demodulation. Chapter 2 describes each type of FM demodulator separately, and it includes all significant types of demodulator for FM radio broadcast. The function of the coincidence demodulator and its characteristics are explained in detail. Chapter 3 contains a theoretical solution of the phase shift network. Calculated values of the circuit elements are verified by simulation with a view to the total harmonic distortion of the demodulator output signal. Chapter 4 describes the front-end circuit of the receiver. Here, the filter design and the mixer circuit description are provided. The final part of the thesis presents the applicable laboratory task.

Submitted work engages in suggestion of frequency-selection filters with usage of more active elements of the MCMI (Multi-Output Current Mirror and inverter). The preamble of thesis is applied to theory of frequency-selection filters and possible usage of them. The projected circuit layouts with the active elements are discussed in terms of the impact of parasitic properties of the real models. The part of thesis is numerical suggestion of found solutions, their simulation in suitable program.

In this thesis is discussed a filter design of a band-pass substrate integrated waveguide filter on the frequency of 5 GHz. It also includes design theory, filter synthesis, filter analysis in the program CST Microwave Studio® and the results of measurement on a vector network analyzer. The analysis results are compared with the measured results. Good agreement between simulated and measured results is observed.

My master’s thesis deals with methods of measuring the ultrasonic blood flow blood vessel with a detailed focus on Doppler ultrasound systems, which find application in the diagnosis of superficial vascular and obstetrics. The thesis is described a proposal indicating polydirectional Doppler system with a continuous carrier wave frequency of 4 MHz, the intensity of ultrasound 100 mW/cm2 and diameter D-shaped transducers 8 mm. As a result, the indicator will be able to measure blood flow velocity in the range of 5-40 cm/s, which appears to 3.5 digit display. After describing important theoretical assumptions, the work pays block diagram indicator. Furthermore, it examines the various functional blocks on the requirements imposed on them. It looks at the options of each functional block, and finally describes the implementation of the selected option and including peripheral solutions. Great attention is paid to the power of the indicator, where the power supply will be used 9 V battery. Create a symmetric voltage for operate amplifier and other auxiliary voltage will procure DC/DC converters. In conclusion, the work is located around the perimeter solutions indicator. The following draft for the production of double-sided PCB, its installation and a list of elements. The outcome of the thesis is complete documentation for the implementation of an indicator of blood flow, which allows us to obtain information on throughput vessels, especially the lower and upper limbs.

In radio frequency (RF), filtering is an essential part of RF transceivers. They are employed for different purposes of band selection, channel selection, interference cancellation, image rejection, etc. These are all translated in selecting the wanted signal while mitigating the rest. This can be performed by either selecting the desired frequency range by a band pass filter or rejecting the unwanted part by a band stop filter. Although there has been tremendous effort to design RF tunable filters, there is still lack of designs with frequency and bandwidth software-tuning capability at frequencies above 4 GHz. This prevents the implementation of Software Defined Radios (SDR) where software tuning is a critical part in supporting multiple standards and frequency bands. Designing a tunable integrated filter will not only assist in realization of SDR, but it also causes an enormous shrinkage in the size of the circuit by replacing the current bulky off-chip filters. The main purpose of this research is to design integrated band pass and band stop filters aimed to perform interference cancellation. In order to do so, two systems are proposed for this thesis. The first system is a band pass filter capable of frequency and band with tuning for C band frequency range (4-8 GHz) and is implemented in 0.13 µm BiCMOS technology. Frequency tunability is accomplished by using a variable capacitor (varactor) and bandwidth tuning is carried out by employing a negative transconductance cell to compensate for the loss of the elements. Additional circuitry is added to the band pass filter to enhance the selectivity of the filter. The second system is a band stop filter (notch) with the same capability as the band pass filter in terms of tuning. This system is implemented in C band, similar to its band stop counterpart and is capable of tuning its depth by using a negative transconductance in an LC tank. A negative feedback is added to the circuit to improve the bandwidth. While implemented in the same process as the band pass filter, it only employs CMOS transistors since it is generally more attractive due to its lower cost and scalability. Both of the systems mentioned use a varactor for changing the center frequency which is a nonlinear element. Therefore, the nonlinearity of it is modelled using two different methods of nonlinear feedback and Volterra series in order to gain further understanding of the nonlinear process taking place in the LC tank. After the validation of the models proposed using Cadence Virtuoso simulator, two methods of design and tuning are suggested to improve the linearity of the system. After post layout-extraction, the band pass filter is capable of Q tuning in the range of 3 to 270 and higher. With the noise figure of 10 to 14 dB and input 1-dB compression point as high as 2 dBm, the system shows a reasonably good performance along its operating frequency of 4 to 8 GHz. The band stop filter which is designed in the same frequency band can achieve better than 55 dB of rejection with the noise figure of 6.7 to 8.8 dB and 1-dB compression point of -4 dBm. With the power consumption of 39 to 70 mW, the band stop filter can be used in a low power receiver to suppress unwanted signals. The technique used in the band stop filter can be applied to higher frequency ranges if the circuit is implemented in a more advanced silicon technology. Implementing the mentioned filters in a receiver along with other elements of low noise amplifiers, mixers, etc. would be a major step toward full implementation of SDR systems. Studying the linearity theory of varactors would help future designers identify the sources of nonlinearity and suggest more efficient tuning techniques to improve the linearity of RF electronic systems. / Master of Science

This master's thesis presents the design and the realization of a low noise amplifier (LNA) for the S band of radio frequency spectrum from 2.3 GHz to 2.4 GHz. This thesis is mainly focused on stability and impedance matching networks study. Ansoft Designer and ANSYS HFSS programs are used for this design to simulate the LNA. Different low noise devices are simulated in order to find the best results for the final design. Moreover, a coaxial cavity resonator is designed in the input of the LNA and works as a band pass filter. Finally, the LNA is fabricated and its properties compared with the simulation results.

This thesis deals with ultrasound blood flow meter design with emphasis on practical implementation of such device. This medical device is used in ultrasound diagnostic, especially for measuring direction and velocity of blood flow in superficial vessels. This thesis contains consecutive design including description of individual function blocks. Documents for making double-sided printed circuit are included as well.

Una línia de transmissió three-line-microstrip consisteix en tres pistes paral·leles practicades sobre la cara d'un dielèctric amb un pla de massa inferior. La propagació en aquesta línia es pot descriure en termes de tres modes fonamentals anomenats ee, oo i oe. Tot i que aquests modes són ortogonals interaccionen entre sí a qualsevol transició, discontinuïtat o asimetria. En el pla d'una transició o asimetria es genera un intercanvi d'energia o conversió modal en el que prenen part tots els modes.En aquest treball s'analitza la conversió modal que s'origina en un conjunt de transicions i asimetries construïdes sobre línies three-line-microstrip. L'estudi es realitza aplicant la tècnica de l'anàlisi multimodal. L'ús d'aquesta tècnica permet la deducció d'una sèrie de models multimodals (un per a cada transició) que proporcionen una anàlisi simple, rigorosa i quantitativa d'aquest fenomen.La validesa d'aquest estudi es verifica de manera experimental. Els bons resultats obtinguts demostren que els models multimodals proposats prediuen de manera precisa el comportament de les transicions. Aquest fet permet el seu ús per analitzar circuits o estructures constituïts per trams de tres pistes acoblades. En el cas d'aquesta tesi, han estat aplicats als camps de l'EMC i de les microones. Pel que fa a l'EMC, s'ha realitzat un estudi de l'acoblament i la integritat del senyal en configuracions de PCB amb trams de tres pistes acoblades. Aquest estudi ha permès identificar les transicions i asimetries en aquests circuits com a possibles fonts d'interferència i de degradació dels senyals ja que la conversió modal es pot interpretar com a un procés d'interferència que involucra tots els senyals presents. Pel que fa a les microones, s'ha realitzat una anàlisi multimodal de filtres spurline. Aquesta anàlisi ha permès desenvolupar dues noves estructures, la principal característica de les quals és la seva compacitat que, a diferència d'altres estructures similars, s'aconsegueix permetent la presència d'un nou mode en el procés de ressonància. L'ús dels models multimodals per a l'anàlisi d'aquestes estructures ha permès una interpretació clara i senzilla del seu funcionament així com el desenvolupament d'una sèrie de regles de disseny que permeten un ajust fàcil i ràpid de certs paràmetres dels filtres com ara la freqüència central i l'ample de banda. / Una línea de transmisión three-line-microstrip consiste en tres pistas paralelas practicadas sobre la cara de un dieléctrico con un plano de masa inferior. La propagación en esta línea se puede describir en términos de tres modos fundamentales llamados ee, oo i oe. Aunque estos modos son ortogonales interaccionan entre se en cualquier transición, discontinuidad o asimetría. En el plano de una transición o asimetría se genera un intercambio de energía o conversión modal en el que toman parte todos los modos.En este trabajo se analiza la conversión modal que se origina en un conjunto de transiciones i asimetrías construidas sobre líneas three-line-microstrip. El estudio se realiza aplicando la técnica del análisis multimodal. El uso de esta técnica permite la deducción de una serie de modelos multimodales (un per a cada transición) que proporcionan un análisis simple, riguroso i cuantitativo de este fenómeno.La validez de este estudio se verifica de manera experimental. Los buenos resultados obtenidos demuestran que los modelos multimodales propuestos predicen de manera precisa el comportamiento de las transiciones. Este hecho permite su uso para analizar circuitos o estructuras constituidos por tramos de tres pistas acopladas. En esta tesis doctoral, han sido aplicados a los campos de la EMC i de las microondas. En el primero de ellos, se ha realizado un estudio del acoplamiento y la integridad de la señal en configuraciones de PCB con tramos de tres pistas acopladas. Este estudio ha permitido identificar las transiciones y asimetrías en estos circuitos como posibles fuentes de interferencia y de degradación de las señales ya que la conversión modal se puede interpretar como a un proceso de interferencia que involucra todas las señales presentes. En el campo de las microondas, se ha realizado un análisis multimodal de filtros spurline. Este análisis ha permitido desarrollar dos nuevas estructuras, cuya principal característica es su compacidad que, a diferencia de otras estructuras similares, se consigue permitiendo la presencia de un nuevo modo en el proceso de resonancia. El uso de los modelos multimodales para el análisis de estas estructuras ha permitido una interpretación clara i sencilla del su funcionamiento así como el desarrollo de una serie de reglas de diseño que permiten un ajuste fácil i rápido de ciertos parámetros de los filtros como por ejemplo la frecuencia central y el ancho de banda. / A three-line-microstrip transmission line consists of three parallel coupled strips printed on a grounded dielectric substrate. The propagation in this line can be described in terms of three fundamental modes, namely the ee, oo and oe modes. These modes are orthogonal and propagate independently unless a transition or asymmetry is present in the line. Any transition or asymmetry will generate an energy exchange or modal interaction among all the propagating modes. In this work, the modal interaction of a set of transitions and asymmetries in three-line-microstrip transmission lines is analyzed. The study is carried out by using the multimodal analysis. By means of this technique a set of multimodal circuit models (one for each transition) is derived. These models provide a simple and a quantitative interpretation of the modal interaction.The proposed multimodal analysis is experimentally validated. The obtained results show that the derived multimodal models accurately predict the behavior of the transitions. Due to this fact, they can be used for the analysis of circuits and structures composed of three-coupled-strip sections. In this work, the models have been applied to both the EMC and microwave fields. In the former, they have been employed to study the cross-talk and signal-integrity problems in PCB configurations involving tree-coupled-trace sections. The performed analysis has shown that transitions and asymmetries in these circuits must be considered as a source of interference and signal degradation since the modal interaction can be interpreted as an interference process that involves all the present signals. In the latter, a multimodal analysis of spurline filters has been performed. This study has allowed the derivation of two new filter structures whose main feature is their compactness, which, in contrast to other analogous filters, is achieved by allowing the presence of an additional mode in the resonance process. The use of the multimodal models for the analysis of these structures has permitted both a simple interpretation of the filter operation and the derivation of a set of design rules which allows a rapid fine tuning of some filter parameters such as the center frequency and the bandwidth.