No description available.

Satellite communication (Satcom) services are used worldwide for voice, data, and video links due to various appealing features. Parabolic reflector antennas are typically used to serve a cost effective scheme for commercial applications. However, mount degradation, roof sag, and orbital decay motivate the need for beam steering. Limited scan range beam steering opens a third option for electronic beam steering with lower cost than full aperture phased arrays and higher tracking speed and accuracy than mechanical-only steering.Multiple high efficiency passive patch array feeds were designed, fabricated, and measured, including a 2x2 MSA array, a stacked shorted annular patch antenna, and an SIW-fed hexagonal array feed based on PTFE material, achieving performance comparable to a horn feed. For multiband dual polarization applications, passive MSA feed solutions are also provided. Multiple MSA array feeds with high isolation were designed for dual band dual polarization applications. More functionality can be realized with multi-layer PCB techniques for complex communication scenarios.Limited scan range electronic beam-steering with a parabolic reflector fed by an active array feed which only needs gain control was demonstrated experimentally, leading to a low cost and effective solution for active beam scanning. A cost-effective flat-panel phased array with limited scan range electronic beam-steering was proposed by tiling high efficiency 4x4 passive subarrays and performing beam scanning at the tile level. The sidelobe issue was also investigated to comply with the pattern mask requirement set by FCC.To enable better use of circularly polarized (CP) MSAs for electronically beam-formed antenna systems, the impact of mutual coupling on the performance of high-sensitivity dual-polarized receivers for satellite communications applications was analyzed. A new analysis method for intrinsically dual-CP MSAs based on an equivalent circuit model and Jones matrices was proposed and validated to overcome the port isolation challenge. The model provides accurate estimates of impedances and S-parameters, as well as field parameters such as axial ratio. The feasible region for XPI and impedance mismatch factor is found for dual CP antennas. The circuit model enables multiple useful applications. Effective decoupling and matching schemes was proposed and demonstrated, leading to a high isolation, good match, and wide AR bandwidth dual CP MSA for satellite communications.

The objectives of this work were to investigate, design and implement beam steering antenna arrays for mobile and wireless applications using the genetic algorithm (GA) and particle swarm optimisation (PSO) techniques as optimisation design tools. Several antenna designs were implemented and tested: initially, a printed dipole antenna integrated with a duplex RF switch used for mobile base station antenna beam steering was investigated. A coplanar waveguide (CPW) to coplanar strip (CPS) transition was adopted to feed the printed dipole. A novel RF switch circuit, used to control the RF signal fed to the dipole antenna and placed directly before it, was proposed. The measured performance of the RF switch was tested and the results confirmed its viability. Then two hybrid coupled PIN diode phase shifters, using Branchline and Rat-Race ring coupler structures, were designed and tested. The generation of four distinct phase shifts was implemented and studied. The variations of the scattering parameters were found to be realistic, with an acceptable ±2 phase shift tolerance. Next, antenna beam steering was achieved by implementing RF switches with ON or OFF mode functions to excite the radiating elements of the antenna array. The switching control process was implemented using a genetic algorithm (GA) method, subject to scalar and binary genes. Anti-phase feeding of radiating elements was also investigated. A ring antenna array with reflectors was modelled and analysed. An antenna of this type for mobile base stations was designed and simulation results are presented. Following this, a novel concept for simple beam steering using a uniform antenna array operated at 2.4 GHz was designed using GA. The antenna is fed by a single RF input source and the steering elements are reactively tuned by varactor diodes in series with small inductors. The beam-control procedure was derived through the use of a genetic algorithm based on adjusting the required reactance values to obtain the optimum solution as indicated by the cost function. The GA was also initially used as an optimisation tool to derive the antenna design from its specification. Finally, reactive loading and time modulated switching techniques are applied to steer the beam of a circular uniformly spaced antenna array having a source element at its centre. Genetic algorithm (GA) and particle swarm optimisation (PSO) processes calculate the optimal values of reactances loading the parasitic elements, for which the gain can be optimised in a desired direction. For time modulated switching, GA and PSO also determine the optimal on and off times of the parasitic elements for which the difference in currents induced optimises the gain and steering of the beam in a desired direction. These methods were demonstrated by investigating a vertically polarised antenna configuration. A prototype antenna was constructed and experimental results compared with the simulations. Results showed that near optimal solutions for gain optimisation, sidelobe level reduction and beam steering are achievable by utilising these methods. In addition, a simple switching process is employed to steer the beam of a horizontally polarised circular antenna array. A time modulated switching process is applied through Genetic Algorithm optimisation. Several model examples illustrate the radiation beams and the switching time process of each element in the array.

No description available.

No description available.

De nombreuses applications civiles et militaires (faisceaux hertziens, futurs réseaux mobiles, communications par satellite, radars automobiles, systèmes d’imagerie haute résolution) nécessitent des antennes à faisceau reconfigurable (dépointage de faisceau, faisceaux multiples, faisceaux formés). Les antennes à réseaux transmetteurs apparaissent comme une alternative aux réseaux phasés classiques ou aux réseaux réflecteurs pour ces applications. L’objectif principal de cette thèse est de démontrer la faisabilité de réseaux reconfigurables fabriqués avec des technologies standards en bande Ka (20-30 GHz). Divers cellules élémentaires utilisant des diodes p-i-n et fonctionnant en polarisation linéaire ou circulaire ont été conçues, optimisées et caractérisées. Les mesures en guide d’onde montrent des pertes minimales de 1,09 dB à 29,0 GHz et une bande passante à 3 dB de 14,7%. Une méthode de simulation hybride a été développée afin d’analyser efficacement des réseaux de grandes dimensions utilisant des rotations séquentielles d’éléments pour optimiser la qualité de polarisation et les diagrammes de rayonnement. Un réseau de 400 cellules élémentaires fonctionnant en polarisation circulaire a été réalisé et testé en chambre anéchoïque. Un dépointage électronique de ±60° et la possibilité de commuter entre les deux polarisations circulaires (droite/gauche) ont été démontrés. / Several civil and military applications (hertzian beams, satellite communications, automotive radars, high resolution imaging systems) require antennas with reconfigurable beam capabilities (beam-scanning, beamshaping, multiple beam generation). Transmitarray antennas are good candidates and represent an alternative to classical phased arrays or reflect-arrays for these applications. The main objective of this thesis is to demonstrate the feasibility of reconfigurable transmitarrays fabricated with standard technologies in Ka-band (20-30 GHz). Different unit-cell designs based on p-i-n diodes have been developed to work in linear and circular polarization. Their optimization and experimental characterization have been performed. Waveguide measurements show insertion losses of 1.09 dB at 29.0 GHz with a 3-dB bandwidth of 14.7%. A hybrid simulation technique has been developed in order to analyze efficiently large transmitarrays in which the sequential rotation technique has been applied to optimize the polarization quality and the radiation patterns. A 400-elements transmitarray operating in circular polarization has been realized and tested in anechoic chamber. A beam-scanning angular coverage of ±60° and circular polarization selection (left/right) have been demonstrated.

The aim of this project was to produce an integrate-able free space optical transceiver for Specks. Specks are tiny computing units that together can form a powerful network called a SpeckNet. The SpeckNet platform is developed by the SpeckNet consortium, which consists of five Scottish Universities and combines computer science, electrical engineering and digital signal processing groups. The principal goal of creating an optical transceiver was achieved by integrating in-house fabricated VCSELs (with lasing thresholds below 400 uA) and custom designed detectors on the SpeckNet platform. The transceiver has a very low power consumption (approximately 100 uW), which removes the need for synchronous communication through the SpeckNet thus making the network more efficient. I describe both static and dynamic beam control techniques. For static control, I used micro-lenses. I fabricated the lenses by greyscale electron beam lithography and integrated them directly on VCSEL arrays. I achieved a steering angle of 10 degrees with this design. I also looked at integrated gratings etched straight into a VCSEL and observed beam steering with an efficiency of 60% For dynamic control, I implemented a liquid crystal (LC) design. I built a LC cell with 30 individually controlled pixels, but I only achieved a steering angle of 1 degree. Furthermore, I investigated two different techniques for achieving beam steering by interference, using coupled VCSELs (a phased array approach). Firstly, using photonic crystals etched into the surface of the VCSEL, I built coupled laser cavities. Secondly, I designed and built bow-tie type VCSELs that were optically coupled but electrically isolated. These designs work by differential current injection causing an interference effect in the VCSELs far field. This technique is the first stepping stone towards realising a phased optical array. Finally, I considered signal detection. Using the same VCSEL material, I built a resonant-cavity detector. This detector had a better background rejection ratio than commercially available silicon devices.

Il y a à l'heure actuelle un grand besoin d'antennes reconfigurables dans la bande des 60 GHz pour des applications de télédétection et de télécommunications sans fil très hauts débits. Les solutions traditionnelles de reconfiguration sont basées sur des semiconducteurs ou des composants RF-MEMS, qui connaissent un coût, une complexité et des pertes croissantes en bande millimétrique. Dans cette thèse, une approche originale a été développée : elle est basée sur la reconfiguration mécanique d'antennes et dispositifs millimétriques microrubans sur substrat élastomère ultrasouple PDMS grâce à des actionneurs MEMS grands déplacements. Premièrement, les choix de conception, la technique de simulation éléments finis (HFSS), et surtout la microfabrication d'antennes sur membrane PDMS ainsi que les techniques de mesure en impédance et rayonnement sont abordés.Deux axes ont ensuite été étudiés : les antennes accordables en fréquence, et les antennes et composants pour le balayage angulaire (déphaseurs et antennes à balayage mécanique de type scanner). Des procédés technologiques innovants ont été développés (reports de métallisations épaisses biocompatibles et d'aimants permanents en couches minces sur membrane PDMS) et différentes techniques d'actionnement (pneumatique, magnétique, par électromouillage) ont été mises en œuvre. Les performances en terme d'accord en fréquence (8,2 %) et de balayage angulaire (-90/+100°) dépassent l'état de l'art des antennes du même type en bande millimétrique, et ceci en utilisant une technologie peu complexe, ultra bas-coût et prometteuse pour la montée en fréquence. / There is currently an increasing need for reconfigurable antennas in the 60 GHz band for remote sensing applications and wireless communications. Traditional reconfiguration solutions are based on semiconductors or RF-MEMS but these components face cost, complexity and losses issues at millimeter-waves.In this thesis, an original approach was developed: it is based on the mechanical reconfiguration of millimeter-wave microstrip antennas and devices printed on ultrasoft PDMS substrates, thank to large displacements MEMS actuators. First, the design choices, the finite element simulation technique (HFSS), and the microfabrication of antennas supported by PDMS membranes as well as the impedance and radiation measurements techniques have been discussed. Two axis have then been studied: frequency-tunable antennas, and beam-steering components (phase shifters and "scanner" type antennas). Innovative technological processes were developed (transfer of biocompatible metal patterns and permanent magnet thin films on PDMS membranes) and several actuation techniques (pneumatic, magnetic, electrowetting) were implemented. Performances in terms of frequency tuning (8.2%) and scan angles (-90 / 100 °) are beyond the state of the art for similar antennas in the millimeter-wave band, and are achieved by using a very simple, ultra low-cost technique that is expected to be effective at even higher frequencies.

The thesis is focused on the research of THz antenna arrays to be used for communications. Attention is turned to modeling metallic surfaces at THz frequencies, a proper characterization of gold conductivity, its relation to Drude model and corresponding measurements. Moreover, the best methods for modeling thin metallic layers (depending on the skin depth related to the metal thickness) are presented. An optimized element of a THz 2×2 antenna array designed for the application of communications is developed in a way that enables an expansion to a larger array. The expansion ability is demonstrated on a 4×4 antenna array which is presented in the thesis too. The designed antennas achieve parameters better than the state-of-art antennas. The presented antennas radiate circularly polarized wave at THz frequencies, operate in a wide bandwidth, have a high gain and are of a compact size. In the thesis, an 8×8 antenna array with a beam steering capability is presented. The main beam of the antenna array can be controlled in two dimensions. A high gain of the radiated circularly-polarized wave can be achieved that way. Different approaches to modeling antennas with thin metallic layers are compared and the best methods are recommended from the viewpoint of different requirements. The designed 2×2 and 4×4 antenna arrays are manufactured using a microfabrication technology. Each step of the fabrication is described in detail and discussed. The reflection coefficient at the input of antennas is measured and compared with simulations. Discrepancies in results are associated with surface roughness which is analyzed by a scanning probe microscope and a scanning electron microscope. By down-scaling the developed THz antenna, a low-profile high-gain antenna for Ka-band space applications is designed. The presented antenna achieves better results than state-of-art CubeSat antennas. The antenna performance is verified by a prototype to be operated at 9 GHz, and the radiation characteristics are experimentally confirmed.

No description available.