This diploma thesis is aimed on cutting tools made of cemented carbides. It characterizes marking, production and properties of non-coating and coating cemented carbides and describes the latest trends in coating. Target of this diploma thesis is comparison of assortment of two important world’s producers and one Czech producer in term of used productive technologies, products microstructure, coatings types, coatings methods and possibilities of their usage. Cutting data were evaluated and compared from obtained technical knowledge, which were recommended by chosen producers for effective turning application of their cutting tools. Recommended cutting speeds were found out for specific type of cutting material according to ISO, width depth of cut and for specific values of feeds per revolution.

The aim of this thesis is a complex processing of obtained technical findings in the area of cutting materials, especially the evaluation and comparison of work possibilities recommended by prime world manufacturers for effective usage and application of coated and uncoated cemented carbides. Characteristics of cemented carbides in terms of production, marking method, physical and mechanical properties and application. Comparison of cemented carbides in the range of production of the most significant world tool and cutting material producers. Cutting efficiency evaluation of the tool. Recommended areas and operating conditions for effective usage of cemented carbides and their technical economic evaluation.

In this Master Thesis work, the effect of pressure on sintering of cemented carbides is investigated. Special focus hasbeen given to the residual porosity after sintering. It is well known that sintering shrinkage depends on binder phasecontent, grain size, temperature and pressure. Thus 4 different cemented carbides grades were selected. The gradeswere pressed into standard products and TRS (Tensile Rupture Strength) rods with two different shrinkage factors.These were then sintered at different pressures and temperatures. Thereafter the impact of pressure on propertiessuch as Density, Coercivity, Porosity and TRS were analyzed. The observations were further supported with Weibullprobability analysis and fracture surface analysis in SEM.It has been shown that there exists a distinct threshold pressure at which significant reduction in porosity occurs forgiven compacted densities. For 3 out of 4 cemented carbide grades it has been observed that P2 sintering pressure issufficient to meet desired product characteristics. The fourth grade required a minimum sintering pressure of P4 toachieve desired quality criteria. Moreover it has been concluded that an increased sintering pressure increasesmaterial strength, as compared to vacuum sintering, thereby reducing the amount of early failures caused by poresduring TRS test.                                    Keywords: Cemented Carbides, Pressurized Sintering, Tungsten carbide, Porosity, Vacuum sintering, TensileRupture Strength, Weibull analysis, Fracture surface analysis.

A fundamental quantum mechanical modelling approach is used for calculating liquid diffusion parameters in cemented carbides. Up to now, no detailed description of diffusion for alloying elements in a liquid Co matrix is available. Neither are experimental measurements found in the literature for the self- or impurity diffusion in the liquid Co system. State of the art application is the description of gradient formation in cemented carbide systems using DICTRA. In this work it is assumed that diffusion during sintering of cemented carbides takes place mainly in the liquid Co binder phase. With this assumption one can calculate the diffusion coefficient for different alloying elements like W, Ti, N and C in a liquid Co matrix phase. The mean square displacement (MSD) of the diffusing atoms is used to obtain the diffusion coefficients which could be simulated by Ab initio Molecular Dynamics (AIMD). By fitting the computed temperature dependence with the Arrhenius relation one can determine the frequency factor and the activation energy which allows to give a quantitative description of the diffusion. Three methods will be used for validating the data from this work. Available estimated literature values based on calculations (scaling laws, a modified Sutherland equation and classical molecular dynamics) will be used to compare the results in a first instance. The general agreement for diffusion in liquid metals will be done by comparison with experimental data for the liquid Fe system. In a last step, the diffusion values obtained by this work will be used to create a kinetic database for DICTRA. The gradient simulations will be compared with experimentally measured gradients. The AIMD simulations are performed for binary diffusion systems to investigate the diffusion between the liquid Co matrix and one type of alloying element. In a second approach the diffusion for a multicomponent systems with Co, W, Ti and C has been performed. The results from the present AIMD simulations could be shown to be in good agreement with the literature. Only two DICTRA simulations could be performed within the timeframe of this work. Both are predicting a ~3 times bigger gradient zone whereas the initial choice of the labyrinth factor λ = f could be identified as a possible source of disagreement. A labyrinth factor of λ = f2 with the calculated mobility values from the AIMD calculations should give improved results. Although the results from those simulations are not available to this date. The two approaches of the diffusion simulations in the binary and multicomponent system are giving matching results. The non-metallic elements C and N are diffusing two times faster than the fastest metallic element Co. The diffusivity of Ti is slightly lower than Co and W could be identified as the element with the slowest diffusion within the liquid Co matrix. Further investigations of the liquid structure could indicate the tendency to form bonds between C and W and between C and Ti. This gives slowed down diffusion of C in the multicomponent system compared to the diffusion in the binary Co-C system.

This thesis deals with a summary of different types and characteristics of coatings used for increasing the lifetime of cemented carbide tools. Besides, the thesis includes solving the issue regarding edge chipping during machining interrupted pipe ends at the pipe line, selecting a new type of indexable inserts and indexable inserts holders to increase line productivity and decrease tool costs in the related operation.

Les matrices en carbure de Tungstène et Cobalt (WC‐Co) sont utilisées dans les procédés de frappe à froid de l’acier pour leur exceptionnelle capacité à résister aux phénomènes d’usure. Ces travaux ont pour objectif de mieux comprendre les mécanismes complexes qui entrainent finalement la dérive des matrices vers l’état usé. Cette complexité vient des liens étroits entre la microstructure et les propriétés mécaniques macroscopiques de ces matériaux. Pour la compréhension des mécanismes de dérive vers l’usure, une stratégie de travail en quatre étapes est établie. La première étape est le prélèvement de matrices de frappe, avec différentes durées de vie, directement sur la chaîne de production. La deuxième étape est l’identification de la rhéologie. Elle s’accompagne de la modélisation numérique du procédé de frappe pour calculer le champ des contraintes et des déformations plastiques. La troisième étape est la caractérisation localisée de l’évolution de la surface selon trois axes : les propriétés tribologiques, morphologiques, et mécaniques. On quantifie ainsi la dégradation progressive des conditions de contact corrélée avec une fragilisation des surfaces et la décohésion de grains de carbures WC. Pour comprendre les mécanismes qui conduisent à la décohésion de grains, une stratégie de modélisation numérique à l'échelle mésomécaniques 2D est mise en place. L’énergie de rupture entre un grain et le reste du matériau est modélisée par des éléments cohésifs. Ces modèles montrent que la sensibilité de chaque grain à l’arrachement dépend non seulement des conditions de contact et de la ténacité du matériau, mais également de la taille et de la configuration du grain au voisinage de la surface. / Tungsten carbide and Cobalt (WC‐Co) dies are used for cold forming processes of steel because of their exceptional performances in resisting wear phenomena. This work aims to a better understanding of the complex damage mechanisms that eventually cause wear. This complexity comes from the existing relationships between their microstructure and their macroscopic mechanical properties. For a better understanding of the damage mechanisms leading towards wear, a four‐step strategy is presented. The first step is the cold heading dies sampling directly on the production line. They are collected at different lifetimes. The second step is the identification of the die rheology. It is followed by numerical modeling of the forging process to calculate the stress field and plastic strain magnitude. The third step is to characterize the local evolution of the surface properties along three axes: the tribological, the morphological and mechanical aspects. These analyses quantify the progressive decrease of contact conditions correlated with surface embrittlement and WC carbide grains debonding. To understand the mechanisms that lead to the grains debonding, a set of 2D mesoscale contact models are performed. The fracture energy between a WC grain and the rest of the material is computed using cohesive elements. These models show that the sensitivity to debonding depends not only on the contact conditions and the material fracture toughness, but also on the grain size and grain configuration in the vicinity of the surface.

The aim of this work was to systematically study how the microstructure evolution is affected by the carbon activity in WC-Ni cemented carbides. Seven WC-9.59at%Ni alloys with different carbon activity were sintered at 1500 °C. From investigating these alloys, the carbon window has been experimentally evaluated using light optical microscopy and compared to theoretical carbon window calculated using Thermo-Calc. The overall microstructure of cross sections and raw surfaces have been investigated using scanning electron microscopy. Finally, the WC grain size and distribution have been evaluated using electron backscatter diffraction. It was found that the experimental carbon window was slightly wider than the theoretical carbon window. The WC grain size increased and the grain size distribution got wider with increasing carbon activity. In addition, the largest WC grains showed the largest grain growth by increasing carbon activity. By comparing the present results of grain size and distribution of WC-Ni to previous results of WC-Co, it was found that the WC grain growth was more pronounced and more influenced by the carbon activity.

In the constant pursuit of better-performing cemented carbides, recent studies suggest that a combination of better hardness and toughness can be obtained by changing its WC grain size distribution. As the area is still rather unexplored, this  thesis  aims  to  broaden  the  knowledge  and  answer  whether mechanical properties can be changed by changing the WC grain size distribution, in the context of mining drill bit inserts. This was performed by producing four dual grained material as well as four single grained reference materials, for which the carbon content and presence of alloying element were varied. The materials were characterised and compared with regard to magnetic saturation, magnetic coercivity,  hardness,  fracture  toughness,  wear resistance,  energy  needed  to cause  fracture,  as  well  as  detailed microstructural  analysis  obtained  through imaging and electron backscatter diffraction analysis The results showed that mining drill bit inserts with alternative WC grain size distribution  could  successfully  be  produced,  but  that  a  traditional  bimodal distribution  with  two  peaks  could  not  be  obtained.  The  distribution instead became significantly wider as well as skewed towards larger grains for the dual grained materials compared with their references. It was further also confirmed that the alternative dual grain size distribution could be used to improve the mechanical properties of fracture toughness and wear resistance, but only for material that was not alloyed, and the magnitude of the improvement may be considered  to  be  small.  For  the  alloyed  materials,  it  turned  out  to  be more difficult to influence the mechanical properties, as the improving effect of analloying element outweighed the effect of grain size distribution. / I en ständig jakt på hårdmetall med bättre prestanda, så föreslår ny forskning att en bättre kombination av hårdhet och seghet kan erhållas genom att ändra den mikrostrukturiella  WC-kornstorleksfördelning.  Då  det  ännu  är  ett relativt outforskat område, så har denna studie för avsikt att öka kunskapen genom att besvara frågan om de mekaniska egenskaperna kan förändras genom att ändra på materialets kornstorleksfördelning inom applikationsområdet hårdmetall för bergborrning. Detta gjordes genom att producera fyra material med WC pulver av två olika storlekar, samt fyra referensmaterial med en kornstorlek. För dessa varierades parametrarna kolhalt och närvaro av legeringselement. Materialen karakteriserades och jämfördes med avseende på magnetisk mättnad, magnetisk koercivitet, hårdhet,  brottseghet,  slitstyrka,  energi  som  behövs  för  att  orsaka brott, samt  en  detaljerad  mikrostrukturanalys  som  erhölls  genom  avbildning samt elektrondiffraktionsanalys. Resultaten visade att material med alternativ WC-kornstorleksfördelning kunde produceras, men att en fullt bimodal fördelning inte gick att skapa i denna studie. Fördelningen blev istället betydligt bredare samt förskjuten mot större korn för materialen som innhöll WC av två olika storlekar. Det bekräftades också att den alternativa     kornstorleksfördelningen     kunde     förbättra     de     mekaniska egenskaperna för brottseghet och slitstyrka, men endast för de material som inte var legerade och storleken på förbättringen får dessutom anses vara relativt liten. För de legerade materialen visade det sig vara svårare att påverka de mekaniska egenskaperna,  eftersom  den  förbättring  av egenskaper  som  legeringselement tillförde överträffade effekten av kornstorleksfördelning.

In the present work further modifications are implemented to an existing test setup for the evaluation of the wear of cemented carbide drill buttons in rock drilling applications. The test setup has been evaluated in previous diploma works, which has shown that the test successfully mimics the wear seen in rock drilling applications. The new modifications include friction and normal force measurements together with the collection of rock debris. This has been made possible by redesigning the sample holder and by manufacturing equipment making rock debris collection possible. The new modifications to the test setup were evaluated by comparing the wear of three different cemented carbide grades tested against sandstone and granite with two different loads. The data collected from the new modifications were found to be robust with lower than expected spread of data. The coefficient of friction when testing against sandstone was higher than when testing against granite. More adhered material was observed on the wear surface when testing against granite than against sandstone. Load dependence on the wear of the cemented carbide buttons is only seen for the softer cemented carbide grades when testing against sandstone. The wear of the buttons indicates a high dependence on the hardness of the different grades as shouldbe expected. This diploma work has been performed for Sandvik Mining, Rock Tools,a world leading supplier of rock drill equipment.

This master‘s thesis is presenting the way of the optimization of grinding characteristics when grinding cemented carbides by diamond wheels. There is described the theory of grinding, including grinding wheels and basic characteristics of cemented carbides in the theoretical part. There are defined experimental metering accomplished on the CNC grinding machine Walter Helitronic Power Mini in the practical part. There were tested eight grinding wheels. The grinding rate, surface roughness Ra, theoretic guaranteed storage period of grinding wheel in number of cuts, theoretical capacity of machined material, achievement of grinding machine and behaviour of the wheels when grinding ware evaluated from the reached results.