Strain-hardening cement-based composites (SHCC) are a special class of fiber-reinforced concrete which develop multiple, fine cracks when subjected to increasing tensile loading, reaching strain capacities of up to several percent. The tensile behavior of SHCC is a result of a purposeful material design accounting for the mechanical and physical properties of the cementitious matrix, of the reinforcing fibers and of their interaction. The exceptionally high energy dissipation through inelastic deformations before reaching tensile strength makes SHCC suitable for manufacturing or strengthening of structural elements which may be subjected to impact loading. However, the tensile behavior of SHCC is highly strain rate dependent, both in terms of tensile strength and strain capacity. The different strain rate sensitivities of the constitutive phases of SHCC (matrix, fiber and interfacial bond) lead to disproportionate dynamic alteration of their mechanical properties under increasing strain rates and, consequently, to an impairment of the micromechanical balance necessary for strain-hardening and multiple cracking. Thus, high energy dissipation under impact loading can only be ensured through a targeted material design. This work presents a series of mechanical experiments at different strain rates and different scales of investigation with the goal of developing a qualitative and quantitative basis for formulating material design recommendations for impact resistant SHCC. Three different types of SHCC were investigated, consisting of two types of polymer fibers (polyvinyl-alcohol and high-density polyethylene) and cementitious matrices (normal-strength and high-strength). Uniaxial tension experiments were performed on SHCC specimens and on non-reinforced matrix specimens with different testing setups at strain rates ranging from 10-4 to 150 s-1. Besides the measured mechanical properties, special attention was paid to the crack patterns and the condition of fracture surfaces. Additionally, micro-scale investigations were performed to quantify the strain rate dependent changes in the mechanical behavior of individual component phases, i.e., matrix, fibers and fiber-matrix bond. The results obtained from the micromechanical investigations were used in an analytical model for crack bridging. The model links the micromechanical parameters and their strain rate sensitivities to the single-crack opening behavior under increasing displacement rates, making it useful for material design purposes. If given an extensive experimental basis for the fracture mechanical properties of the non-reinforced cementitious matrices, the model can be extended for predicting the strain capacity (multiple cracking) of SHCC under different strain rates. / Die hochduktilen Betone (Engl.: Strain-Hardening Cement-based Composites – SHCC) bilden eine besondere Klasse von Faserbetonen, die eine multiple Rissbildung unter zunehmenden Zugspannungen aufweisen, was zu einer sehr hohen Bruchdehnung führt. Das dehnungsverfestigende, hochduktile Zugverhalten der SHCC wird durch eine gezielte Materialentwicklung erreicht, die die mechanischen und physikalischen Eigenschaften der zementgebundenen Matrizen, der Kurzfasern und deren Zusammenwirkung berücksichtigt. Das außergewöhnliche Energieabsorptionsvermögen der SHCC durch plastische Verformungen vor dem Erreichen der Zugfestigkeit qualifiziert diese Verbundwerkstoffe für die Herstellung oder Verstärkung von Bauteilen, die Impaktbeanspruchungen ausgesetzt sein könnten. Jedoch weisen SHCC sowohl bezüglich deren Zugfestigkeit als auch deren Dehnungskapazität ein ausgeprägtes dehnratenabhängiges Verhalten auf. Unter zunehmenden Dehnraten führen die unterschiedlichen Dehnratensensitivitäten der gestaltenden Phasen von SHCC (Matrix, Faser und deren Verbund) zur Beeinträchtigung des mikromechanischen Gleichgewichts, welches für die Dehnungsverfestigung und multiple Rissbildung erforderlich ist. Eine hohe Energiedissipation unter Impaktbeanspruchungen kann deshalb nur durch eine gezielte Materialentwicklung der SHCC hinsichtlich deren Verhaltens unter hohen Dehnraten gewährleistet werden. Die vorliegende Arbeit umfasst eine Reihe von experimentellen Untersuchungen mit verschiedenen Dehnraten und an unterschiedlichen Betrachtungsebenen, mit dem Ziel eine qualitative und quantitative Basis für Empfehlungen zur Materialentwicklung von Impakt-resistenten SHCC zu schaffen. Drei verschiedene SHCC-Zusammensetzungen wurden untersucht. Die Referenz-Zusammensetzung aus einer normalfesten zementgebundenen Matrix und Polyvinyl-Alkohol-Kurzfasern wurde mit zwei unterschiedlichen SHCC verglichen (hochfest und normalfest), die mit Kurzfasern aus hochdichtem Polyethylen bewehrt wurden. Einaxiale Zugversuche wurden an SHCC-Proben und unbewehrten Matrix-Proben mit verschiedenen Prüfvorrichtungen bei Dehnraten von 10-4 bis 150 s-1 durchgeführt. Zusätzlich zu den gemessenen mechanischen Eigenschaften wurden die Rissbildung und die Bruchflächen detailliert untersucht. Darüber hinaus wurden mikromechanische Untersuchungen durchgeführt, um die Dehnratensensitivität der einzelnen Phasen, d.h. Matrix, Faser und deren Verbund zu beschreiben. Die aus den mikromechanischen Untersuchungen erzielten Ergebnisse wurden als Eingangswerte in einem analytischen Einzelriss-Modell verwendet. Das entwickelte Modell verbindet die mikromechanischen Parameter und deren Dehnratenabhängigkeit mit dem Rissöffnungsverhalten von SHCC bei zunehmenden Verschiebungsraten. Das macht es vorteilhaft für Materialentwicklungszwecke. Das Modell kann für die Vorhersage der Dehnungskapazität von SHCC bei diversen Dehnraten weiterentwickelt werden, wenn eine umfassende experimentelle Basis für die bruchmechanischen Eigenschaften der Matrizen vorliegt.

This paper focuses on two experimental methods that give indicators linked to the impregnation level of the yarn / matrix interface, in the case of Textile Reinforced Concrete (TRC). These methods have been tested on three different glass yarns laid in a cementitious matrix, with three different impregnation levels resulting from the manufacturing process. The first method (comparative mercury intrusion porosity test) is based on the evaluation by mercury intrusion porosity of the pores volume associated to the porosity inside and near the yarn. The second method (flow test) consists in measuring the flow rate of water along the yarn, with imposed flow conditions. The physical parameters measured by these two methods are both related to the pore size and to the porosity of the yarn / matrix interface. The results of the two methods are discussed and drawn in parallel to a qualitative characterization of the yarn matrix interface made by scanning electron microscopy. As a result, the connection between the results of the two methods and the SEM characterization is studied. It is shown how these methods can participate to characterize the yarn impregnation. Limitations of the methods are also discussed.

Strain-hardening cement-based composites (SHCC) are a special class of fiber-reinforced concrete which develop multiple, fine cracks when subjected to increasing tensile loading, reaching strain capacities of up to several percent. The tensile behavior of SHCC is a result of a purposeful material design accounting for the mechanical and physical properties of the cementitious matrix, of the reinforcing fibers and of their interaction. The exceptionally high energy dissipation through inelastic deformations before reaching tensile strength makes SHCC suitable for manufacturing or strengthening of structural elements which may be subjected to impact loading. However, the tensile behavior of SHCC is highly strain rate dependent, both in terms of tensile strength and strain capacity. The different strain rate sensitivities of the constitutive phases of SHCC (matrix, fiber and interfacial bond) lead to disproportionate dynamic alteration of their mechanical properties under increasing strain rates and, consequently, to an impairment of the micromechanical balance necessary for strain-hardening and multiple cracking. Thus, high energy dissipation under impact loading can only be ensured through a targeted material design. This work presents a series of mechanical experiments at different strain rates and different scales of investigation with the goal of developing a qualitative and quantitative basis for formulating material design recommendations for impact resistant SHCC. Three different types of SHCC were investigated, consisting of two types of polymer fibers (polyvinyl-alcohol and high-density polyethylene) and cementitious matrices (normal-strength and high-strength). Uniaxial tension experiments were performed on SHCC specimens and on non-reinforced matrix specimens with different testing setups at strain rates ranging from 10-4 to 150 s-1. Besides the measured mechanical properties, special attention was paid to the crack patterns and the condition of fracture surfaces. Additionally, micro-scale investigations were performed to quantify the strain rate dependent changes in the mechanical behavior of individual component phases, i.e., matrix, fibers and fiber-matrix bond. The results obtained from the micromechanical investigations were used in an analytical model for crack bridging. The model links the micromechanical parameters and their strain rate sensitivities to the single-crack opening behavior under increasing displacement rates, making it useful for material design purposes. If given an extensive experimental basis for the fracture mechanical properties of the non-reinforced cementitious matrices, the model can be extended for predicting the strain capacity (multiple cracking) of SHCC under different strain rates. / Die hochduktilen Betone (Engl.: Strain-Hardening Cement-based Composites – SHCC) bilden eine besondere Klasse von Faserbetonen, die eine multiple Rissbildung unter zunehmenden Zugspannungen aufweisen, was zu einer sehr hohen Bruchdehnung führt. Das dehnungsverfestigende, hochduktile Zugverhalten der SHCC wird durch eine gezielte Materialentwicklung erreicht, die die mechanischen und physikalischen Eigenschaften der zementgebundenen Matrizen, der Kurzfasern und deren Zusammenwirkung berücksichtigt. Das außergewöhnliche Energieabsorptionsvermögen der SHCC durch plastische Verformungen vor dem Erreichen der Zugfestigkeit qualifiziert diese Verbundwerkstoffe für die Herstellung oder Verstärkung von Bauteilen, die Impaktbeanspruchungen ausgesetzt sein könnten. Jedoch weisen SHCC sowohl bezüglich deren Zugfestigkeit als auch deren Dehnungskapazität ein ausgeprägtes dehnratenabhängiges Verhalten auf. Unter zunehmenden Dehnraten führen die unterschiedlichen Dehnratensensitivitäten der gestaltenden Phasen von SHCC (Matrix, Faser und deren Verbund) zur Beeinträchtigung des mikromechanischen Gleichgewichts, welches für die Dehnungsverfestigung und multiple Rissbildung erforderlich ist. Eine hohe Energiedissipation unter Impaktbeanspruchungen kann deshalb nur durch eine gezielte Materialentwicklung der SHCC hinsichtlich deren Verhaltens unter hohen Dehnraten gewährleistet werden. Die vorliegende Arbeit umfasst eine Reihe von experimentellen Untersuchungen mit verschiedenen Dehnraten und an unterschiedlichen Betrachtungsebenen, mit dem Ziel eine qualitative und quantitative Basis für Empfehlungen zur Materialentwicklung von Impakt-resistenten SHCC zu schaffen. Drei verschiedene SHCC-Zusammensetzungen wurden untersucht. Die Referenz-Zusammensetzung aus einer normalfesten zementgebundenen Matrix und Polyvinyl-Alkohol-Kurzfasern wurde mit zwei unterschiedlichen SHCC verglichen (hochfest und normalfest), die mit Kurzfasern aus hochdichtem Polyethylen bewehrt wurden. Einaxiale Zugversuche wurden an SHCC-Proben und unbewehrten Matrix-Proben mit verschiedenen Prüfvorrichtungen bei Dehnraten von 10-4 bis 150 s-1 durchgeführt. Zusätzlich zu den gemessenen mechanischen Eigenschaften wurden die Rissbildung und die Bruchflächen detailliert untersucht. Darüber hinaus wurden mikromechanische Untersuchungen durchgeführt, um die Dehnratensensitivität der einzelnen Phasen, d.h. Matrix, Faser und deren Verbund zu beschreiben. Die aus den mikromechanischen Untersuchungen erzielten Ergebnisse wurden als Eingangswerte in einem analytischen Einzelriss-Modell verwendet. Das entwickelte Modell verbindet die mikromechanischen Parameter und deren Dehnratenabhängigkeit mit dem Rissöffnungsverhalten von SHCC bei zunehmenden Verschiebungsraten. Das macht es vorteilhaft für Materialentwicklungszwecke. Das Modell kann für die Vorhersage der Dehnungskapazität von SHCC bei diversen Dehnraten weiterentwickelt werden, wenn eine umfassende experimentelle Basis für die bruchmechanischen Eigenschaften der Matrizen vorliegt.

Fabric Reinforced Cementitious Matrix (FRCM) composites utilize a mineral mortar matrix as a substitute for epoxy resin that is used for Fibre Reinforced Polymer (FRP). This eliminates issues associated with the low thermal compatibility of FRP with concrete, susceptibility to UV radiation, and sensitivity to high temperatures in which organic polymers undergo vitrification. This study discussed the effect of varying parameters like the number of Carbon-FRCM (C-FRCM) layers (1, 2 and 3 layers), different anchorage configurations (non-anchored, spike anchor, wrap anchor and mechanical anchor), bond length (300 or 200 mm), and the fabric type (unidirectional and bidirectional) on the direct shear behaviour of C-FRCM composites bonded to a concrete substrate, especially the fibre-matrix bond which is the most common debonding interface of FRCM composites. Calibrated models of the bond – slip behaviour are provided based on the fabric type and number of fabric layers. The results indicate that the anchor type and the overall composite thickness are the main factors that control the failure mode of the composite. All properly anchored specimens using spike and wrap anchors failed due to fabric rupture. Moreover, a considerable number of the non-anchored specimens failed due to composite-substrate debonding, although premature fabric rupture was frequently observed. Furthermore, specimens with bidirectional fabric demonstrated shallower penetration of the strain into the composite which may be due to the horizontal fabric strands providing some anchorage for the longitudinal strands. They also exhibited slip initiation at a higher stress compared to unidirectional specimens. In addition, slip initiation stress of unidirectional specimens decreased with more fabric layers which may indicate that the additional layers have a lower bond efficiency. For the same reason, specimens with three layers of fabric generally experienced deeper strain penetration into the composite than one-layered or two-layered specimens regardless of the anchor type. The results also indicate that the use of bidirectional fabric and anchorage systems decreases the strain penetration into the composite and correspondingly, the effective length is shortened. Surface strain measurements captured using digital image correlation generally did not match the internal fabric strain values obtained from strain gauges.

Master of Science / Department of Civil Engineering / Hayder A. Rasheed / Throughout history natural fiber was used as one of the main building materials all over the world. Because the use of such materials has decreased in the last century, not much research has been conducted to investigate their performance as a reinforcing material in cement and concrete. In order to investigate one of the most common natural fibers, wheat fibers, as a reinforcing material, 156 mortar specimens and 99 concrete specimens were tested. The specimens were tested in either uniaxial compression or flexure. The uniaxial compression test included 2 in (50.8 mm) mortar cubes and 4x8 in (101.6 x 203.2 mm) concrete cylinders. As for the flexure test, they were either 40x40x160 mm cementitious matrix prisms or 6x6x21 in (152.4x152.4x533.4 mm) concrete prisms. Several wheat fibers percentages were studied and compared with polypropylene fiber as a benchmarking alternative. The average increase in the uniaxial compression strength for cementitious matrix cubes reinforced with 0.5% long wheat fiber exceeded that of their counterparts reinforced with polypropylene fiber by 15%. Whereas for concrete cylinders reinforced with 0.75% long wheat fiber, their strength exceeded that of their counterparts reinforced with polypropylene fiber by 5% and that of the control by 7%. The flexural strength of cementitious matrix prisms reinforced with 0.75% long wheat fiber exceeded that of their counterparts reinforced with polypropylene fiber by 27%. Meanwhile, concrete prisms reinforced with both long wheat fiber and polypropylene fiber showed deterioration in strength of up to 17%. Finally, ABAQUS models were developed for concrete cylinders and prisms to simulate the effect of inclusion of the wheat fibers.

[pt] O uso de todos os tipos de amianto na construção civil tem diminuído drasticamente devido a problemas sérios de saúde associados a sua manipulação. De fato é previsto banir totalmente o seu uso, dentro de um curto espaço de tempo, nos países desenvolvidos bem como nos em desenvolvimento. Na necessidade de se encontrar um substituto adequado para o amianto, tem-se pesquisado compósitos de argamassa reforçada com fibras vegetais e polpas celulósicas. Devido ao processo de polpação, que remove as impurezas não celulósicas, como a lignina e a hemicelulose, diminuindo o ataque às fibras, sem a necessidade de recorrer a modificações na matriz cimentícia, as polpas celulósicas podem ser o substituto ideal para o amianto. Assim sendo, o principal objetivo desta dissertação é determinar experimentalmente as características mecânicas e os parâmetros de fratura de compósitos de matriz cimentícia reforçada por polpa de bambu refinada e sem refino. As polpas celulósicas foram utilizadas nas porcentagens de 8 e 14 por cento em relação à massa do cimento, porcentagens estas que, conforme a literatura, são associadas à otimização da energia absorvida no ensaio de flexão. A avaliação do comportamento mecânico dos compósitos considerados neste trabalho foi realizada através de ensaios de compressão e impacto, bem como de flexão em três pontos em espécimes não entalhados e em outros contendo entalhes de raios de curvatura diferentes. Propriedades mecânicas, tais como módulo de elasticidade, resistência à compressão, ao impacto e à flexão, bem como integral J na carga máxima, são apresentadas e discutidas em termos de aspectos microestruturais e fractográficos dos corpos de prova ensaiados. / [en] As handling and manipulation of asbestos pose grave health hazards, its use in civil construction has been drastically dwindling and will in fact be completely prohibited, in a few years, in developed countries. With the need arising to find an adequate substitute, vegetable fibers and cellulosic pulps have been considered to be viable alternatives. Taking into account the fact that the process for pulp production entails the removal of impurities, such as lignin and hemicellulose, cellulosic pulps seem to be the ideal substitute to asbestos, as their use does not necessitate modifications in the cementitious matrix. Accordingly, the purpose of this work is to experimentally determine basic mechanical characteristics and pertinent fracture parameters of bamboo pulp reinforced cement. Refined and non-refined pulps were used in the proportions of 8 and 14 percent of the weight of dry cement. These percentages were adopted as they imply, according to literature, in optimizing the energy absorbed by the composite in bend loading. Evaluation of the mechanical behavior of the composites considered in this work was realized by means of compression and impact testing. Three point bend tests were also carried out using unnotched as well as notched specimens of different notch root radii. Mechanical properties such as modulus of elasticity, compressive, impact and bend strengths, and J integral at maximum load are presented and discussed in terms of pertinent microstructural and fractographic aspects of test specimens.

[pt] O objetivo deste trabalho foi avaliar as propriedades mecânicas, físicas e microestruturais de materiais compósitos cimentícios reforçados por fibras naturais e de laminados de bambu. O trabalho experimental foi direcionado para a determinação da tenacidade. Para se determinar a tenacidade foram utilizados três tipos de ensaios: impacto Charpy, impacto balístico e flexão em 3 pontos. Após os ensaios, a superfície de fratura dos corpos-de-prova foi analisada por microscopia eletrônica de varredura (MEV). Esta análise microestrutural serviu para determinar os modos de fratura e validar as hipóteses feitas nos modelos matemáticos utilizados. Foram usados modelos adaptados da literatura para a determinação da tenacidade e os valores teóricos obtidos foram confrontados com os experimentais. Determinou-se também através de modelos encontrados na literatura a tensão interfacial de todas as fibras utilizadas nesta pesquisa. Os modelos empregados para calcular a tenacidade e a tensão de adesão interfacial, se mostraram eficientes e válidos. Em segundo plano, porém não menos importante, ficou a determinação das propriedades térmicas dos materiais utilizados. Foram efetuados ensaios de condutividade térmica do compósito e ensaios termogravimétricos das fibras vegetais e do bambu. Os compósitos cimentícios foram reforçados por diferentes fibras naturais: polpa refinada de bambu (CPB), polpa de sisal (CPS), polpa de eucalipto (CPE), fibras curtas de sisal (CPFS) e wollastonita (CPW). As proporções das polpas de bambu, sisal e eucalipto utilizadas como reforço nas matrizes cimentícias foram de 8 por cento e 14 por cento em relação à massa do cimento, a da fibra curta de sisal (25 mm) foi de 3 por cento em relação ao volume e a da wollastonita foi de 11,5 por cento em relação à massa. Compóstios híbridos feitos com wollastonita e polpa de bambu (CPBW) foram também produzidos apenas variando a proporção da polpa de bambu em 8 por cento e 14 por cento e mantendo fixa a da wollastonita em 11,5 por cento. Como uma tentativa de se melhorar a resistência ao impacto, laminados CPB/AL foram também fabricados colando duas chapas de alumínio (liga 5052 H34) de espessura 0,8 mm em ambas às faces dos compósitos reforçados por fibra de bambu, formando assim compósitos sanduíche (CPBA). O bambu Moso (Phyllostachys heterocycla pubescens) com 5 anos de idade foi usado para fabricação dos laminados de bambu, sendo tratado com água fervida para a prevenção de ataques biológicos. Técnicas para a extração do laminado a partir de seu formato natural foram estudadas estabelecendo suas vantagens e desvantagens. Para o ensaio de impacto foram utilizados corpos-de-prova com dimensão nominal de 120 mm x 15 mm x 6 mm perfazendo um total de 18 corpos-de-prova. Para o de flexão foram realizados ensaios com uma lâmina simples de bambu (BL) e bambu laminado colado (BLC) com 3 camadas de lâminas dispostas ortogonalmente. Os resultados dos testes de impacto Charpy e flexão em 3 pontos comprovaram a boa tenacidade do bambu laminado quando submetido a cargas de impacto (42,54 kJ/m2) e a cargas estáticas (19,77 kJ/m2 para o laminado e 17,63 kJ/m2 para o laminado colado). Compósitos sanduíche constituídos de alumínio e laminados de bambu foram também fabricados. Estes foram analisados através de ensaios de impacto balísticos seguindo as recomendações da norma NIJ 0101.04. Observações no microscópico eletrônico de varredura foram realizadas para se analisar os mecanismos de falha dos laminados. / [en] The main objective of this work was to evaluate the mechanical, physical and microestructure properties of cementitious composite materials and bamboo laminates. The experimental program was focused on the determination of toughness. Three diferent types of tests were performed in order to establish it: Charpy impact, ballistic impact and three point bending test. After the tests, the fractured surface of the failed test specimens was observed using a Scanning Electron Microscope (SEM) to establish the failure mode. Mathematical models adapted from the available literature were used to determine the toughness from which the values were confronted to the ones obtained experimentally. It was also determined by mathematical models the interfacial bond stress of all fibers used in this research. The two models, used in the toughness and interfacial bond stress calculation, showed to be efficient, providing valid results. In second plan, but not less important, was the determination of the materials thermal properties. Thermal conductivity tests of the composites and thermogravimetry of the fibers and bamboo were performed. The cementitious composites were reinforced by different natural fibers: refined bamboo pulp (CPB), sisal pulp (CPS), eucalyptus pulp (CPE), short sisal fibers (CPFS) and wollastonite. The mass fraction of bamboo, sisal and eucalyptus pulp studied were 8 percent and 14 percent. For the wollastonite fiber the mass fraction studied was 11.5 percent and for the short sisal fiber a 3 percent volume fraction was studied. Hybrid composites made with wollastonite and bamboo pulp (CPBW) were also produced varying the bamboo fraction mass to 8 percent and 14 percent but keeping constant to 11.5 percent the wollastonite mass fraction. The slurry de-watering process was used in the production of all composites described before. To reduce the adverse effects of weathering on the cellulose fibers and to improve the impact load and flexural resistance of the composite, aluminum thin sheets were used to produce a sandwich composite lamina with the CPB, which was denominated as CPBA. Compound Adhesive gel from Otto Baumgart which is a type of epoxy was used to fix the aluminum sheets on the CPB. The use of aluminum has proved to give much higher impact resistance results when compared to the CPB ones. The 5 years old Moso bamboo (Phyllostachys heterocycla pubescens), which was previously treated in boiled water to eliminate biological agents, was used to produce the bamboo laminates. Techniques were developed to extract bamboo laminates from its natural form, establishing its advantages and disadvantages. For the Charpy impact test, a total of 18 specimens with nominal dimensions of 120 mm x 15 mm x 6 mm were tested. Laminated (BL) and 3 layer cross ply laminated bamboo (BLC) were tested in bending. A total of 9 specimens were tested per bamboo configuration. The BL specimens had nominal dimensions of 120 mm x 30 mm x 6 mm and the BLC were 120 mm x 30 mm x 17 mm. The results demonstrated the good toughness of bamboo laminates when subject to dynamic (42.54 kJ/m2) and to static load (19.77 kJ/m2 for the laminate and 17.63 kJ/m2 for the cross ply laminate). Aluminum thin sheets were again used to make sandwich composites, but now using the bamboo laminate (BLCA). The BLCA was tested using the ballistic impact test following the standard NIJ 0101.04. Analysis on the Scanning Eléctron Microscope (SEM) were performed in order to establish the laminate s failure mechanisms.

Short fibres of different materials are used for crack bridging in strain-hardening cement-based composites (SHCC). Their mechanical properties and the fibre-matrix interphase on the micro level have a significant influence on the macroscopic component properties. Investigations on the specific modification and adaptation of fibre properties in relation with the failure mechanisms at different strain rates hardly exist so far, since mainly commercially available fibres are used. In the frame of this work, two different fibre types – polypropylene (PP) fibres and alkali-resistant (AR) glass fibres – were produced on lab spinning devices and the properties were adapted in such a way that fundamental correlations between the influence of fibre geometry, mechanical properties, chemical functionalities and surface structure on the behaviour during fibre pull-out from the concrete matrix can be derived. The PP fibres were produced with different degrees of stretching, cross-sectional geometries (circular, trilobal) and fibre diameters, as well as without and with sizing. The resulting changes in the crystallinity of the PP structure, surface roughness and wetting behaviour could be demonstrated by differential scanning calorimetry (DSC), roughness measurements by atomic force microscopy (AFM), and contact angle measurements. AR glass fibres were used in the unsized state and various chemical surface treatments were applied. Aqueous polymer dispersions of different materials were characterized in detail regarding particle size, pH value, solid content, and surface tension. In addition, their film-forming properties were evaluated using prepared polymer films. Furthermore, the influence of cross-linking agents on the thermal and mechanical stability of polyurethane sizings was investigated using thermal analysis methods. After application of the sizings to the AR glass surface, changes in surface structure and roughness could be observed by scanning electron microscopy (SEM) and AFM. The amount of sizing, or rather the polymer content on the fibres, was systematically increased and investigated in the non-cross-linked and cross-linked state with respect to energy absorption during fibre pull-out. Using a high-strength concrete matrix, all modified PP and AR glass fibres were used to produce and test single-fibre model composites by single-fibre pull-out tests, whereby the fibre pull-out was either quasi-static or dynamic. Based on the test results, design strategies for PP and AR glass fibres were derived at the end of the thesis. / Für die Rissüberbrückung in hochduktilen Betonen (Strain-Hardening Cement-based Composites – SHCC) werden Kurzfasern verschiedener Materialien eingesetzt. Ihre mechanischen Eigenschaften und die Faser-Matrix-Grenzschicht auf der Mikroebene beeinflussen die makroskopischen Bauteileigenschaften deutlich. Untersuchungen zur gezielten Veränderung und Anpassung von Fasereigenschaften im Zusammenhang mit den Versagensmechanismen bei unterschiedlichen Dehnraten existieren bisher kaum, da überwiegend kommerziell verfügbare Fasern eingesetzt werden. Im Rahmen dieser Arbeit wurden daher zwei verschiedene Fasertypen – Polypropylen (PP)-Fasern und alkaliresistente (AR)-Glasfasern – an Laborspinnanlagen selbst hergestellt und die Eigenschaften so angepasst, dass sich grundlegende Zusammenhänge zwischen dem Einfluss von Fasergeometrie, mechanischen Eigenschaften, chemischen Funktionalitäten und Oberflächenstruktur auf das Verhalten bei Faserauszug aus der Betonmatrix ableiten lassen. Die PP-Fasern wurden mit verschiedenen Verstreckungsgraden, Querschnittsgeometrien (rund, trilobal), Faserdurchmessern sowie ohne und mit Schlichte hergestellt. Die dadurch hervorgerufenen Eigenschaftsveränderungen hinsichtlich Kristallinität der PP-Struktur, der Oberflächenrauheit und des Benetzungsverhaltens konnten durch dynamische Differenzkalorimetrie (DSC), Rauheitsmessungen mittels Rasterkraftmikroskopie (AFM) und Kontaktwinkelmessungen nachgewiesen werden. AR-Glasfasern wurden im ungeschlichteten Zustand verwendet und verschiedene chemische Oberflächenbehandlungen durchgeführt. Es wurden wässrige Polymerdispersionen verschiedener Materialien detailliert hinsichtlich ihrer Partikelgröße, pH-Wert, Feststoffgehalt und Oberflächenspannung charakterisiert sowie ihre Filmbildungseigenschaften anhand hergestellter Polymerfilme bewertet. Weiterhin wurde der Einfluss von Vernetzern auf die thermische und mechanische Stabilität von Polyurethanschlichten mit Methoden der thermischen Analyse untersucht. Nach dem Applizieren der Schlichten auf die AR-Glasoberfläche konnten Veränderungen der Oberflächenstruktur und Rauheit mit Rasterelektronenmikroskopie (REM) sowie AFM beobachtet werden. Die Schlichtemenge bzw. der Polymeranteil auf den Fasern wurde systematisch erhöht und im unvernetzten sowie vernetzten Zustand hinsichtlich der Energieabsorption bei Faserauszug untersucht. Mit allen modifizierten PP-Fasern und AR-Glasfasern wurden unter Einsatz einer hochfesten Betonmatrix Einzelfaser-Modellverbunde zur Durchführung von Einzelfaserauszugversuchen (Single-Fibre Pull-Out) hergestellt und geprüft, wobei der Faserauszug entweder quasistatisch oder dynamisch erfolgte. Basierend auf den Versuchsergebnissen wurden am Ende der Arbeit für PP-Fasern und AR-Glasfasern Designstrategien abgeleitet.