In both the chemical and mechanical pulping process, the logs are cut into wood chips by a disc chipper before fibre separation. To make the wood chipping process more efficient, one have to investigate in detail the coupling between process parameters and the quality of the chips. One objective of this thesis was to obtain an understanding of the fundamental mechanisms behind the creation of wood chips. Another objective with the thesis was to investigate whether it was possible to, in a way tailor the chipping process so as to reduce the energy consumption in a following mechanical refining process. Both experimental and analytical/numerical approaches have been taken in this work. The first part of the experimental investigations, were performed with an in-house developed chipping device and a digital speckle photography equipment. The results from the experimental investigation showed that the friction between the log and chipping tool is probably one crucial factor for the chip formation. Further more it was found that the indentation process is approximately self-similar, and that the stress field over the entire crack-plane is critical for chip creation. The developed analytical model predicts the normal and shear strain distribution and to be more specific, the model can predict the compressive stresses parallel to the fibre direction for an assumed linear elastic and orthotropic material. The analytical distributions were found to be in reasonable agreement with the corresponding distributions obtained from a finite element analysis. To be able to study the chipping process under realistic conditions, which for example means to use chipping rates representative for a real wood chipper, a laboratory chipper was developed. Details regarding the chipper and how to evaluate the force measurements are given together with an example of how the force on the cutting tool (the knife) varies with time during cutting. To investigate the influence of a certain chipping process parameter, the chips were after production in the laboratory chipper, refined in a pilot refiner during conditions optimized for TMP (thermomechanical pulp) and CTMP (chemithermomechanical pulp) processes. It was concluded that the details concerning the chip process had a large impact on e.g. the energy consumption in both first stage and second stage refining. Results showing this are given in this thesis. / För både kemisk och mekanisk pappersmassa så tillverkas flis av trädstockar med hjälp av en skivhugg innan fibrerna separeras. För att göra flisningsprocessen mer effektiv, måste kopplingen mellan processparametrar och fliskvalitet studeras. Ett mål med denna avhandling är att ge fundamental kunskap om mekanismerna bakom bildandet av träflis. Både experimentella och analytiska/numeriska metoder har använts i detta arbete. De experimentella undersökningarna har gjorts med hjälp av egen utvecklad utrustning. Resultaten från den experimentella undersökningen visar att friktionen mellan stammen och flisningsverktyget har betydelse vid flisning. Vidare observerades det att inträngnings processen är approximativt självlik (self similar) och att det är spänningsfältet över hela sprickplanet som är kritiskt för bildandet av en flis. Den utvecklade analytiska modellen förutsäger normal- och skjuvspänningsfördelningen över sprickplanet och kan mer specifikt förutsäga den kompressiva belastning som verkar parallellt fiberriktningen i ett linjärt elastiskt och ortotropt material (trä). De analytiskt bestämda fördelningarna stämmer relativt väl överens med motsvarande fördelningar beräknad med finit element analys. För att kunna studera flisningsprocessen under realistiska förhållanden, vilket bl.a. betyder att skärhastigheter som är representativa för en verklig process skall användas, så utvecklades inom ramen för avhandlingsarbetet, en laboratoriesflishugg. Detaljer rörande flishuggen samt hur uppmätta lastsignaler skall utvärderas ges tillsammans med ett exmpel på hur kraften på skärverktyget (kniven) varierar under ett skärförlopp. Inverkan av en viss flisningsprocessparameter undersöktes genom att flis tillverkades i laboratorieflishuggen varefter de raffinerades i en pilotraffinör under förhållanden som var optimerade för TMP (termomekanisk massa) och CTMP (kemitermomekanisk massa) processerna. Det konstaterades att detaljer i flisningsprocessen hade stor inverkan på t.ex. energiåtgången i både första stegs – och andrastegsraffinering. Resultat som verifierar detta ges i avhandlingen. / <p>At the time of the doctoral defense, the following papers were unpublished and had a status as follows: Paper 3: Submitted. Paper 4: Submitted. Paper 5: Submitted.</p>

Die maschinelle Gewinnung ist in der Lage, den verantwortungsvollen Umgang mit Lagerstätten und die Sicherheit in Bergwerken zu erhöhen. Dennoch hat sie sich bisher nicht in gekurvten Strecken und in untertägigen Abbauen des Festgesteinsbergbaus etablieren können. Es wird daher überprüft, welche Aktivierungsparameter nötig sind, um den Anwendungsbereich der schrämenden Werkzeuge auf hochfeste Gesteine zu erweitern. Anhand von sechs Gesteinen werden einerseits die Leistungsfähigkeit des schrämenden Lösens und die Herausforderungen mit zunehmender Festigkeit der Gesteine, andererseits das schlagende Lösen und sein potenzieller Beitrag zur Leistungssteigerung untersucht. Dazu erfolgt die systematische Bestimmung der Gewinnungsparameter und die der gegenseitigen Abhängigkeiten. Am Einzelmeißel werden Orientierung, Schlagenergie, Abstand und Abfolge von Einzelschlägen untersucht, um eine Prognose für günstige Aktivierungsparameter geben zu können. Die Ergebnisse fließen in das Rechenmodell eines rotierenden Gewinnungsorgans, das die Spanleistung und wichtige Parameter der Gewinnung wahlweise mit oder ohne Aktivierung bestimmt. Der darauffolgende Vergleich der beiden Konzepte ermittelt anhand von zwei Gesteinen die jeweilige Vorzugsvariante.

High-performance materials such as stainless steels and nickel based super alloys are widely used in demanding applications where high mechanical and thermal properties are required. The applications of super alloys are mainly found in jet engines, power plants and gas turbines demanding high fatigue strength, corrosion and oxidation resistance as well as wear resistant properties. In order to use them, they go through various machining processes such as milling, turning, cutting, polishing etc. until the final product is achieved. Modern manufacturing industries employs various machining tools and technologies to improve the machining process of heat resistant super alloys. However, there are still challenges which needs to be addressed. Among them, adhesive wear of the machining tools is one of the main wear mechanism during the tribological interaction of tool and workpiece, preventing them to achieve the desired quality and surface finish of the end product. Moreover, it damages the tool reducing its lifecycle and in return, increasing the production cost. Among the cutting tools tungsten carbide (WC/Co) tools coated with TiAlN coating due to their good high temperature performance are extensively used. Nonetheless, these coatings still face issue like adhesive wear, abrasion, oxidation at higher temperature damaging the tools and subsequent machining. Therefore, it is imperative to understand the initiation mechanism of adhesive wear during the tribological interaction of super alloys and coated cutting tool material. In this research work, the tribological response of two coatings deposited by physical vapour deposition (PVD), having the composition Ti60Al40N and Ti40Al60N have been studied against two super alloys material, i.e. Inconel 718 and stainless steel 316L. A high temperature SRV (Schwingung (Oscillating), Reibung (Friction), Verschleiß (Wear)) reciprocation friction and wear test set up was employed to investigate the friction behaviour, wear rate and dominant wear mechanisms.  For Ti60Al40N coating, the experimental results revealed that generally, friction increases in case of sliding against Inconel 718 up to 400 °C and drops at 760 °C. A high wear volume at room temperature and a decrease to a minimum at 760 °C has been observed for Inconel 718. On the other side, Stainless steel 316L (SS 316L) faces a continuous rise in friction coefficient with highest value at 760 °C during sliding against Ti60Al40N coating. Wear is highest at 400 °C for SS 316L pin. The worn surfaces shows that both workpiece materials experience increase in material transfer due to adhesive wear with rise in temperature. At 400 °C, adhesion is the primary wear mechanism for both workpiece materials. A further rise in temperature to 760 °C promotes the adhesive wear through oxides formation on both material surfaces.  Similarly, Ti40Al60N coating shows the same friction behaviour with change in average steady state friction values for both material of Inconel 718 and SS 316L. Both workpiece materials responds in a similar way to wear volume loss, i.e. lowest at room temperature and highest at 760 °C. For Inconel 718, transfer of coating constituents on to the Inconel 718 pin surface was detected and associated with coating rupture and peeling, exacerbating with rise in temperature. Adhesion, abrasion, and oxidation are primary wear mechanisms at 400 °C and 760 °C. For SS 316L, coating transfer only happen at 400 °C. No damage of coating at 40 °C, a complete damage at 400 °C, and formation of dense porous oxides layers at 760 °C have been noticed. At 400 °C, adhesion, abrasion, and chipping while at 760 °C, adhesion, three body abrasion, ploughing and oxidation are the main wear mechanisms.