Published Article / The world is increasingly being misused by its inhabitants by the wasteful manner that its resources are utilized and the amount of pollution that is generated in the environment. This practice is unsustainable and it is incumbent on the present generation of decision-makers to rectify this phenomenon if our descendants are to have an opportunity to live life in the same manner as we do. Special emphasis should be placed on a reduction in the amount of air pollution that is created by electrical power generating plants, as well as the manner in which potable water is utilized and wasted. In this article the local situation with respect to the generation and use of electrical energy and water is discussed. It is encouraging to see that the National Government is taking strong steps to address these problems. Yet, it might not have the required ability to finance these efforts fully.

One approach to enabling a larger penetration of renewable sources of energy is the implementation of hybrid power plants. This work presents a process to determine the preliminary optimal configuration of a concentrating solar power-coal hybrid power plant with low solar augmentation, and is demonstrated on a coal power plant in Castle Dale, UT. A representative model is developed and validated against published data for a coal power plant of a different configuration than Hunter Unit 3. The simplifications within the representative model include combining multiple feedwater heaters, combining turbines that operate across the same boundary states, and the mass-average calculation for extraction properties to the combined feedwater heaters. It is shown that the representative model can accurately and consistently simulate a coal power plant. Comparing net power generation and boiler heating estimates from the representative model to the benchmark power plant, the representative model is accurate to within +/- 1% the accepted value from the benchmark power plant. The methods for quantifying solar resource with data from the National Renewable Energy Laboratory are presented with the derivation of an algorithm to simulate a concentrating solar power field arrangement. The solar contribution to electrical power output is estimated using an exergy balance. A simplified financial model is also developed to estimate the solar marginal levelized cost of electricity and payback time using a cash-flow analysis. Estimates for solar resource, solar contribution, and financial performance are consistent with data published by the National Renewable Energy Laboratory or in archival literature. A multi-objective optimization routine is developed consisting of the representative model, the augmentation of solar energy into the solar integration model by means of feedwater heater bypass, solar contribution, levelized cost of electricity, and payback time. Because this study considered complete FWH bypass, higher solar augmentation (>3% of boiler heating) is required for a hybrid design to be considered feasible. However, for higher solar augmentation, the costs are also considerably higher and the financial benefit is insufficient to make any hybrid designs feasible unless a carbon tax is in place. A carbon tax will amplify the financial benefit of hybridization, so optimization results are provided assuming a carbon tax value equivalent to the value used in California's Emissions Trading System (16 USD sh.tn.^-1). The impact of a green energy premium price paid by consumers is also explored in the context of payback time. The resulting optimal design for the Hunter Unit 3 with a carbon tax and no premium is using parabolic trough collector technology at an augment fraction of k=9% to bypass feedwater heater 6. The resulting marginal solar levelized cost of electricity is 9.5 x 10^-4 USD kWh^-1 with an estimated payback time of 25.2 years. This process can be applied to any coal power plant for which operating data and meteorological data are available to evaluate preliminary hybridization feasibility.

Thesis (MScEng)--Stellenbosch University, 2014. / ENGLISH ABSTRACT: Concentrating solar power promises to be a potential solution for meeting the worlds energy needs in the future. One of the key features of this type of renewable energy technology is its ability to store energy effectively and relatively cheaply. An air-rock bed thermal energy storage system promises to be an effective and reasonably inexpensive storage system for concentrating solar power plants. Currently there is no such storage system commercially in operation in any concentrating solar power plant, and further research is required before such a system can be implemented. The main research areas to address are the thermal-mechanical behaviour of rocks, rock bed pressure drop correlations and effective and practical system designs. Recent studies have shown that the pressure drop over a packed bed of rocks is dependant on various aspects such as particle orientation relative to the flow direction, particle shape and surface roughness. The irregularity and unpredictability of the particle shapes make it difficult to formulate a general pressure drop correlation. Typical air-rock bed thermal design concepts consist of a large vertical square or cylindrical vessel in which the bed is contained. Such system designs are simple but susceptible to the ratcheting effect and large pressure drops. Several authors have proposed concepts to over-come these issues, but there remains a need for tools to prove the feasibility of the designs. The purpose of this paper is to investigate aDEM-CFD coupled approach that can aid the development of an air-rock bed thermal energy storage system. This study specifically focuses on the use of CFD. A complementary study focusses on DEM. The two areas of focus in this study are the pressure drop and system design. A discrete CFD simulation model is used to predict pressure drop over packed beds containing spherical and irregular particles. DEM is used to create randomly packed beds containing either spherical or irregularly shaped particles. This model is also used to determine the heat transfer between the fluid and particle surface. A porous CFD model is used to model system design concepts. Pressure drop and heat transfer data predicted by the discrete model, is used in the porous model to describe the pressure drop and thermal behaviour of a TES system. Results from the discrete CFD model shows that it can accurately predict the pressure drop over a packed bed of spheres with an average deviation of roughly 10%fromresults found in literature. The heat transfer between the fluid and particle surface also is accurately predicted, with an average deviation of between 13.36 % and 21.83 % from results found in literature. The discrete CFD model for packed beds containing irregular particles presented problems when generating a mesh for the CFD computational domain. The clump logic method was used to represent rock particles in this study. This method was proven by other studies to accurately model the rock particle and the rock packed bed structure using DEM. However, this technique presented problems when generating the surface mesh. As a result a simplified clump model was used to represent the rock particles. This simplified clump model showed characteristics of a packed bed of rocks in terms of pressure drop and heat transfer. However, the results suggest that the particles failed to represent formdrag. This was attributed to absence of blunt surfaces and sharp edges of the simplified clumpmodel normally found on rock particles. The irregular particles presented in this study proved to be inadequate for modelling universal characteristics of a packed bed of rocks in terms of pressure drop. The porous CFD model was validated against experimental measurement to predict the thermal behaviour of rock beds. The application of the porous model demonstrated that it is a useful design tool for system design concepts. / AFRIKAANSE OPSOMMING: Gekonsentreerde sonkrag beloof om ’n potensiële toekomstige oplossing te wees vir die wêreld se groeiende energie behoeftes. Een van die belangrikste eienskappe van hierdie tipe hernubare energie tegnologie is die vermoë om energie doeltreffend en relatief goedkoop te stoor. ’n Lug-klipbed termiese energie stoorstelsel beloof om ’n doeltreffende en redelik goedkoop stoorstelsel vir gekonsentreerde sonkragstasies te wees . Tans is daar geen sodanige stoorstelsel kommersieël in werking in enige gekonsentreerde sonkragstasie nie. Verdere navorsing is nodig voordat so ’n stelsel in werking gestel kan word. Die belangrikste navorsingsgebiede om aan te spreek is die termies-meganiese gedrag van klippe, klipbed drukverlies korrelasies en effektiewe en praktiese stelsel ontwerpe. Onlangse studies het getoon dat die drukverlies oor ’n gepakte bed van klippe afhanklik is van verskeie aspekte soos partikel oriëntasie tot die vloeirigting, partikel vormen oppervlak grofheid. Die onreëlmatigheid en onvoorspelbaarheid van die klip vorms maak dit moeilik om ’n algemene drukverlies korrelasie te formuleer. Tipiese lug-klipbed termiese ontwerp konsepte bestaan uit ’n groot vertikale vierkantige of silindriese houer waarin die gepakte bed is. Sodanige sisteem ontwerpe is eenvoudig, maar vatbaar vir die palrat effek en groot drukverliese. Verskeie studies het voorgestelde konsepte om hierdie kwessies te oorkom, maar daar is steeds ’n behoefte aanmetodes om die haalbaarheid van die ontwerpe te bewys. Die doel van hierdie studie is om ’n Diskreet Element Modelle (DEM) en numeriese vloeidinamika gekoppelde benadering te ontwikkel wat ’n lug-klipbed termiese energie stoorstelsel kan ondersoek. Hierdie studie fokus spesifiek op die gebruik van numeriese vloeidinamika. ’n Aanvullende studie fokus op DEM. Die twee areas van fokus in hierdie studie is die drukverlies en stelsel ontwerp. ’n Diskrete numeriese vloeidinamika simulasie model word gebruik om drukverlies te voorspel oor gepakte beddens met sferiese en onreëlmatige partikels. DEM word gebruik om lukraak gepakte beddens van óf sferiese óf onreëlmatige partikels te skep. Hierdie model is ook gebruik om die hitte-oordrag tussen die vloeistof en partikel oppervlak te bepaal. ’n Poreuse numeriese vloeidinamika model word gebruik omdie stelsel ontwerp konsepte voor te stel. Drukverlies en hitte-oordrag data, voorspel deur die diskrete model, word gebruik in die poreuse model om die drukverlies- en hittegedrag van ’n TES-stelsel te beskryf. Resultate van die diskrete numeriese vloeidinamikamodel toon dat dit akkuraat die drukverlies oor ’n gepakte bed van sfere kan voorspel met ’n gemiddelde afwyking van ongeveer 10%van die resultatewat in die literatuur aangetref word. Die hitte-oordrag tussen die vloeistof en partikel oppervlak is ook akkuraat voorspel, met ’n gemiddelde afwyking van tussen 13.36%en 21.83%van die resultate wat in die literatuur aangetref word. Die diskrete numeriese vloeidinamika model vir gepakte beddens met onreëlmatige partikels bied probleme wanneer ’n maas vir die numeriese vloeidinamika, numeriese domein gegenereer word. Die "clump"logika metode is gebruik om klip partikels te verteenwoordig in hierdie studie. Hierdiemetode is deur ander studies bewys om akkuraat die klip partikel en die klip gepakte bed-struktuur te modelleer deur die gebruik van DEM. Hierdie tegniek het egter probleme gebied toe die oppervlak maas gegenereer is. As gevolg hiervan is ’n vereenvoudigde "clump"model gebruik om die klip partikels te verteenwoordig. Die vereenvoudigde "clump"model vertoon karakteristieke eienskappe van ’n gepakte bed van klippe in terme van drukverlies en hitte oordrag. Die resultate het egter getoon dat die partikels nie vorm weerstand verteenwoordig nie. Hierdie resultate kan toegeskryf word aan die afwesigheid van gladde oppervlaktes en skerp kante, wat normaalweg op klip partikels gevind word, in die vereenvoudigde "clump"model. Die oneweredige partikels wat in hierdie studie voorgestel word, blykomnie geskik tewees vir die modellering van die universele karakteristieke eienskappe van ’n gepakte bed van klippe in terme van drukverlies nie. Die poreuse numeriese vloeidinamika model is met eksperimentele metings bevestig omdie termiese gedrag van klipbeddens te voorspel. Die toepassing van die poreuse model demonstreer dat dit ’n nuttige ontwerp metode is vir stelsel ontwerp konsepte.

Concentrating solar power plants can integrate cost-effective thermal energy storage systems and thereby supply controllable power on demand, an advantage against other renewable technologies. Storage integration allows a solar thermal power plant to increase its load factor and to shift production to periods of peak demand. It also enables output firmness, providing stability to the power block and to the grid. Thus, despite the additional investment, storage can enhance the performance and economic viability of the plants. However, the levelized cost of electricity of these plants yet remains higher than for other technologies, so projects today are only viable through the provision of incentives or technology-specific competitive bid tenders. It is the variability of the solar resource, the myriad roles that storage can assume, and the complexity of enhancing the synergies between the solar field, the storage and the power block, what makes the development of adequate policy instruments, design and operation of these plants a challenging process. In this thesis a comprehensive methodology for the pre-design and analysis of concentrating solar power plants is presented. The methodology is based on a techno-economic modeling approach that allows identifying optimum trade-off curves between technical, environmental, and financial performance indicators. A number of contemporary plant layouts and novel storage and hybridization concepts are assessed to identify optimum plant configurations, in terms of component size and storage dispatch strategies. Conclusions highlight the relevance between the sizing of key plant components, the operation strategy and the boundaries set by the location. The interrelation between critical performance indicators, and their use as decisive parameters, is also discussed. Results are used as a basis to provide recommendations aimed to support the decision making process of key actors along the project development value chain of the plants. This research work and conclusions are primarily meant to set a stepping stone in the research of concentrating solar power plant design and optimization, but also to support the research towards understanding the value of storage in concentrating solar power plants and in the grid. / Koncentrerad solkraft erbjuder möjligheten att integrera kostnadseffektiv termisk energilagring och därmed behovsstyrd kraftkontroll. Detta är en viktig fördel jämfört med andra förnybara energiteknologier. Lagringsintegration tillåter solkraftsanläggningar att öka sin lastfaktor och skifta produktion till tider med största efterfrågan. Vidare möjliggör lagring fast elproduktion vilket leder till förbättrad nät- och kraftturbinstabilitet. Därför kan termisk lagring öka anläggningsprestanda och ekonomiskt värde trots ökande initiala kapitalkostnader. I termer av specifik elproduktionskostnad (LCOE) ligger koncentrerade solkraftsanläggningar med lagring fortfarande högre än andra kraftteknologier och anläggningsprojekt blir endast lönsamma genom subventionsmodeller eller teknologispecifika konkurrensutsatta anbudsförfaranden. Att hitta adekvata policylösningar och optimala design och operationsstrategier är en utmanande process eftersom det gäller att hitta rätt balans mellan variabel solinstrålning, lagring av energi och tid för produktion genom optimal design och operation av solmottagarfält, kraftblock och lagringskapacitet. I denna avhandling presenteras en omfattande metodik för pre-design och analys av koncentrerande solkraftverk. Metodiken baseras på en tekno-ekonomisk modelleringsansats som möjliggör identifiering av optimala avvägningssamband för tekniska, ekonomiska och miljöprestanda indikatorer. Metodiken tillämpas på ett antal moderna anläggningslayouter  och lagrings- och hybridiseringskoncept för att identifiera optimal kraftanläggningsdesign i termer av komponentprestanda och lagringsanvändningsstrategier. I slutsatsen poängteras relevansen av att hitta rätt storlek på nyckelkomponenter i relation till lagringsstrategi och randvillkoren som ges av konstruktionsläget för optimal ekonomisk och miljömässig prestanda. Resultaten används för att formulera rekommendationer till nyckelaktörer i beslutsprocessen genom hela kraftanläggningens värdekedja från politisk beslutsfattare till anläggningsingenjör. Forskningen och slutsatserna i detta arbete skall i första hand ta ett steg framåt för optimering och design av solkraftsanläggningar men även tillhandahålla en metodik för utvärdering av lagringslösningar och dess specifika värde för solkraftsanläggningar och elnätet. / <p>QC 20160829</p>

The Department of Energy funded a project to determine if the specific heat of thermal energy storage materials could be improved by adding nanoparticles. The standard thermal energy storage materials are molten salts. The chosen molten salt was a sodium nitrate and potassium nitrate eutectic, commercially called Hitec Solar Salt. Two nanoparticle types were chosen, alumina and silica. The nanoparticle composite materials were fabricated by mixing the components in an aqueous solution, mixing that solution for a set amount of time using a sonic mixer, then removing the water from the aqueous solution, leaving the composite molten salt behind as a fine white powder. The thermal properties of the composite and plain material were measured using two techniques: American Society for Testing and Materials (ASTM) 1269E and Modulating Differential Scanning Calorimetry (MDSC). These two techniques measured the specific heat and the heat of fusion of the plain and composite materials. The results of all the ASTM and MDSC measurements suggest that the addition of the nanoparticles using the given manufacturing technique increased the specific heat of the molten salt by approximately 20 percent, with both measurement techniques showing approximately the same level of increase. The silica and the alumina improved the specific heat by nearly the same amount over the base material. The heat of fusion did not seem to be significantly altered compared to the observed heat of fusion value of the unmodified material. It was also observed that the nitrate and silica composite material's specific heat decreased if the material was raised to a temperature above 400C. The specific heat was observed to decrease over time, even when the temperature was well below 400C. It is unknown why this occurred. The nitrate plus alumina composite and the plain nitrate were stable to a temperature of 450C for the test duration.

A new receiver concept utilizing impinging jet cooling technology has been developed for a small scale solar dish-Brayton system. In a typical impinging receiver design, the jet nozzles are distributed evenly around the cylindrical absorber wall above the solar peak flux region for managing the temperature at an acceptable level. The absorbed solar irradiation is partially lost to the ambient by radiation and natural convection heat transfer, the major part is conducted through the wall and taken away by the impingement jets to drive a gas turbine. Since the thermal power requirement of a 5 kWe Compower® micro gas turbine (MGT) perfectly matches with the power collected by the EuroDish when the design Direct Normal Irradiance (DNI) input is 800 W/m2, the boundary conditions for the impinging receiver design in this work are based on the combination of the Compower®MGT and the EuroDish system. In order to quickly find feasible receiver geometries and impinging jet nozzle arrangements for achieving acceptable temperature level and temperature distributions on the absorber cavity wall, a novel inverse design method (IDM) has been developed based on a combination of a ray-tracing model and a heat transfer analytical model. In this design method, a heat transfer model of the absorber wall is used for analyzing the main heat transfer process between the cavity wall outer surface, the inner surface and the working fluid. A ray-tracing model is utilized for obtaining the solar radiative boundary conditions for the heat transfer model. Furthermore, the minimum stagnation heat transfer coefficient, the jet pitch and the maximum pressure drop governing equations are used for narrowing down the possible nozzle arrangements. Finally, the curves for the required total heat transfer coefficient distribution are obtained and compared with different selected impinging arrangements on the working fluid side, and candidate design configurations are obtained. Furthermore, a numerical conjugate heat transfer model combined with a ray-tracing model was developed validating the inverse design method and for studying the thermal performance of an impinging receiver in detail. With the help of the modified inverse design method and the numerical conjugate heat transfer model, two impinging receivers based on sintered α-SiC (SSiC) and stainless steel 253 MA material have been successfully designed. The detailed analyses show that for the 253 MA impinging receiver, the average air temperature at the outlet and the thermal efficiency can reach 1071.5 K and 82.7% at a DNI level of 800 W/m2 matching the system requirements well. Furthermore, the local temperature differences on the absorber can be reduced to 130 K and 149 K for two different DNI levels, which is a significant reduction and improvement compared with earlier published cavity receiver designs. The inverse design method has also been verified to be an efficient way in reducing the calculation costs during the design procedure. For the validation and demonstration of the receiver designs, a unique experimental facility was designed and constructed. The facility is a novel high flux solar simulator utilizing for the first time Fresnel lenses to concentrate the light of 12 commercial high power Xenon-arc lamps. Finally, a prototype of a 253 MA based impinging was experimentally studied with the help of the 84 kWe Fresnel lens based high flux solar simulator in KTH. / <p>QC 20151123</p> / Optimised Microturbine Solar Power System , OMSOP

abstract: Fluids such as steam, oils, and molten salts are commonly used to store and transfer heat in a concentrating solar power (CSP) system. Metal oxide materials have received increasing attention for their reversible reduction-oxidation (redox) reaction that permits receiving, storing, and releasing energy through sensible and chemical potential. This study investigates the performance of a 111.7 MWe CSP system coupled with a thermochemical energy storage system (TCES) that uses a redox active metal oxide acting as the heat transfer fluid. A one-dimensional thermodynamic model is introduced for the novel CSP system design, with detailed designs of the underlying nine components developed from first principles and empirical data of the heat transfer media. The model is used to (a) size components, (b) examine intraday operational behaviors of the system against varying solar insolation, (c) calculate annual productivity and performance characteristics over a simulated year, and (d) evaluate factors that affect system performance using sensitivity analysis. Time series simulations use hourly direct normal irradiance (DNI) data for Barstow, California, USA. The nominal system design uses a solar multiple of 1.8 with a storage capacity of six hours for off-sun power generation. The mass of particles to achieve six hours of storage weighs 5,140 metric tonnes. Capacity factor increases by 3.55% for an increase in storage capacity to eight hours which requires an increase in storage volume by 33% or 737 m3, or plant design can be improved by decreasing solar multiple to 1.6 to increase the ratio of annual capacity factor to solar multiple. The solar reduction receiver is the focal point for the concentrated solar energy for inducing an endothermic reaction in the particles under low partial pressure of oxygen, and the reoxidation reactor induces the opposite exothermic reaction by mixing the particles with air to power an air Brayton engine. Stream flow data indicate the solar receiver experiences the largest thermal loss of any component, excluding the solar field. Design and sensitivity analysis of thermal insulation layers for the solar receiver show that additional RSLE-57 insulation material achieves the greatest increase in energetic efficiency of the five materials investigated. / Dissertation/Thesis / Masters Thesis Civil and Environmental Engineering 2017

abstract: Concentrating Solar Power (CSP) plant technology can produce reliable and dispatchable electric power from an intermittent solar resource. Recent advances in thermochemical energy storage (TCES) can offer further improvements to increase off-sun operating hours, improve system efficiency, and the reduce cost of delivered electricity. This work describes a 111.7 MWe CSP plant with TCES using a mixed ionic-electronic conducting metal oxide, CAM28, as both the heat transfer and thermal energy storage media. Turbine inlet temperatures reach 1200 °C in the combined cycle power block. A techno-economic model of the CSP system is developed to evaluate design considerations to meet targets for low-cost and renewable power with 6-14 hours of dispatchable storage for off-sun power generation. Hourly solar insolation data is used for Barstow, California, USA. Baseline design parameters include a 6-hour storage capacity and a 1.8 solar multiple. Sensitivity analyses are performed to evaluate the effect of engineering parameters on total installed cost, generation capacity, and levelized cost of electricity (LCOE). Calculated results indicate a full-scale 111.7 MWe system at $274 million in installed cost can generate 507 GWh per year at a levelized cost of $0.071 per kWh. Expected improvements to design, performance, and costs illustrate options to reduce energy costs to less than $0.06 per kWh. / Dissertation/Thesis / Masters Thesis Civil, Environmental and Sustainable Engineering 2017

The amount of incoming solar energy to earth is greater than any other source. Among existing technologies to harness solar energy there is concentrating solar power (CSP). One advantage of CSP is that is dispatchable, meaning that it can provide power even when the sun is not shining. However, CSP is undergoing challenges which hinder its development such as operating variabilities caused by the fluctuations of the sun or the fact that these systems are not yet cost competitive with respect to other technologies.   One way of improving the performance of CSP plants (CSPPs) is by increasing their operational flexibility, specifically their capability for fast starts. In this way it is possible for the CSPP to harness the solar energy as soon as possible, thus producing more energy and increasing its profitability. Over 90% of CSPPs use a steam turbine to generate electricity. Steam turbines are not currently designed with the flexibility required by the CSP application. Steam turbine start-up is limited by thermal stress and differential expansion. If not carefully controlled, these phenomena either consume lifetime or even result in machine failure. The aim of this work was to understand the improvement potential of steam turbine start-up and quantify this in terms of CSPP performance indicators. For this, a thermo-mechanical steam turbine model was developed and validated. The model was then used to analyze potential improvements and thermal constraints to steam turbine start-up operation. Furthermore, a CSP plant techno-economic model was developed including steam turbine details. This modeling approach including two levels of detail allowed for the particularities of the component to be included within the dynamics of the plant and thus be able to connect the perspectives of the equipment manufacturer with those of the plant operator. Reductions of up to 11.4% in the cost of electricity were found in the studies carried out. / <p>QC 20170814</p>

Concern over the altering climate due to the release of anthropogenic greenhouse gases has caused a major shift in the developments of ways to minimise human impact on the climate. Solar energy is seen as one of the most promising sources to transform the energy market for low-carbon energy generation. Currently, solar power is generated via photovoltaic (PV) and concentrating solar power (CSP) technologies. The advantage of CSPs to scale up renewable energy to utility level, as well as to store thermal energy for electrical power generation when the sun is not available (after sunset or during cloudy periods) makes this technology an attractive option for sustainable clean energy. CSP development, however, is still in its infancy, and for it to be a competitive form of energy-generation technology, techno-economic developments in this field need to improve the efficiency and decrease the costs of this technology. A policy report by the European Academies’ Science Advisory Council (EASAC) (2011) indicated that central receiver (solar tower) CSP systems show the greatest margin for technological improvements (40% to 65% is estimated), and that an improvement in receiver technology could make the greatest contribution to increase efficiency. This study therefore focused on analysing the optical and thermal performance of a new proposed solar cavity molten salt receiver design for a central receiver CSP system using a numerical approach. In this study, the receiver’s performance was analysed by first selecting an existing heliostat field, Planta Solar 10 (PS-10). For the numerical analysis to reflect conditions that are as realistic as possible, numerical models for different aspects were selected and validated. For modelling the sun, the solar tracking numerical model proposed by Iqbal (1983) was selected and implemented after literature and comparison showed adequate results. The direct normal irradiation (DNI) was modelled by applying a clear sky model, with the parameterisation model C proposed by Iqbal (1983) as the chosen model. The variables in this model that were subject to temperature, and humidity values were more accurately presented by adding numerical approximations of the region’s actual weather data. The DNI model reflected realistic fluctuations. For the thermal modelling, a validation study was conducted on impingement flow heat transfer to select an appropriate Reynolds-averaged Navier-Stokes (RANS) model that would provide accurate results when conducting the thermal performance test on the receiver. The study concluded that the transitional Shear Stress Transport (SST) turbulence model performed the best. A new method was also developed and validated that allows one to not only simulate complex geometries within the Monte Carlo ray tracing environment SolTrace, but also to apply the results obtained by simulating this model as a heat source within the computational fluid dynamics (CFD) environment ANSYS Fluent. This allows SolTrace modelling to be more accurate, since models do not need to be approximated to simple geometries. It also provides an alternative for solar modelling in ANSYS Fluent. The optical analysis was conducted by first performing an analysis on the receiver aperture and studying its sensitivity on the captured flux. This was followed by analysing the optics of the proposed receiver, the flux distributions on a simplified absorber surface area, and how these distributions are altered by changing some parameters. An in-depth analysis was finally done on the absorber area by applying the aforementioned model to simulate complex geometries within SolTrace, with the results illustrating the difference of the detailed geometry on optical modelling. An alternative receiver design with improved optical features was proposed, with an initial study providing promising results. The thermal analysis was done within the CFD environment, with only a section of the absorber surface area considered, and by applying the solar flux simulated during the optical analysis as heat source within the geometry model. This allowed the model to simulate the effects of re-radiation at the surface of the absorber while simulating the heat transfer at the fluid molten salt side simultaneously. The results showed that, for the current design and requirements, the absorber surface temperature reaches impractical temperatures. Altering the design or being more lenient on the requirements has, however, shown dramatic improvements in terms of thermal performance. Sensitivity studies for both the optical and thermal analyses have shown that changes in design can dramatically improve the performance of the design, making it a possible feasible receiver design for central receiver systems. / Dissertation (MEng)--University of Pretoria, 2019. / National Research Foundation (NRF) / Mechanical and Aeronautical Engineering / MEng / Unrestricted