No description available.

Thesis (PhD) -- Stellenbosch University, 2014. / ENGLISH ABSTRACT: Currently the reduction of the levelised cost of electricity (LCOE) is the main goal of concentrating solar power (CSP) research. Central to a cost reduction strategy proposed by the American Department of Energy is the use of advanced power cycles like supercritical steam Rankine cycles to increase the efficiency of the CSP plant. A supercritical steam cycle requires source temperatures in excess of 620°C, which is above the maximum storage temperature of the current two-tank molten nitrate salt storage, which stores thermal energy at 565°C. Metallic phase change materials (PCM) can store thermal energy at higher temperatures, and do not have the drawbacks of salt based PCMs. A thermal energy storage (TES) concept is developed that uses both metallic PCMs and liquid metal heat transfer fluids (HTF). The concept was proposed in two iterations, one where steam is generated directly from the PCM – direct steam generation (DSG), and another where a separate liquid metal/water heat exchanger is used – indirect steam generation, (ISG). Eutectic aluminium-silicon alloy (AlSi12) was selected as the ideal metallic PCM for research, and eutectic sodium-potassium alloy (NaK) as the most suitable heat transfer fluid. Thermal energy storage in PCMs results in moving boundary heat transfer problems, which has design implications. The heat transfer analysis of the heat transfer surfaces is significantly simplified if quasi-steady state heat transfer analysis can be assumed, and this is true if the Stefan condition is met. To validate the simplifying assumptions and to prove the concept, a prototype heat storage unit was built. During testing, it was shown that the simplifying assumptions are valid, and that the prototype worked, validating the concept. Unfortunately unexpected corrosion issues limited the experimental work, but highlighted an important aspect of metallic PCM TES. Liquid aluminium based alloys are highly corrosive to most materials and this is a topic for future investigation. To demonstrate the practicality of the concept and to come to terms with the control strategy of both proposed concepts, a storage unit was designed for a 100 MW power plant with 15 hours of thermal storage. Only AlSi12 was used in the design, limiting the power cycle to a subcritical power block. This demonstrated some practicalities about the concept and shed some light on control issues regarding the DSG concept. A techno-economic evaluation of metallic PCM storage concluded that metallic PCMs can be used in conjunction with liquid metal heat transfer fluids to achieve high temperature storage and it should be economically viable if the corrosion issues of aluminium alloys can be resolved. The use of advanced power cycles, metallic PCM storage and liquid metal heat transfer is only merited if significant reduction in LCOE in the whole plant is achieved and only forms part of the solution. Cascading of multiple PCMs across a range of temperatures is required to minimize entropy generation. Two-tank molten salt storage can also be used in conjunction with cascaded metallic PCM storage to minimize cost, but this also needs further investigation. / AFRIKAANSE OPSOMMING: Tans is die minimering van die gemiddelde leeftydkoste van elektrisiteit (GLVE) die hoofdoel van gekonsentreerde son-energie navorsing. In die kosteverminderingsplan wat voorgestel is deur die Amerikaanse Departement van Energie, word die gebruik van gevorderde kragsiklusse aanbeveel. 'n Superkritiese stoom-siklus vereis bron temperature hoër as 620 °C, wat bo die 565 °C maksimum stoor temperatuur van die huidige twee-tenk gesmelte nitraatsout termiese energiestoor (TES) is. Metaal fase veranderingsmateriale (FVMe) kan termiese energie stoor by hoër temperature, en het nie die nadele van soutgebaseerde FVMe nie. ʼn TES konsep word ontwikkel wat gebruik maak van metaal FVM en vloeibare metaal warmteoordrag vloeistof. Die konsep is voorgestel in twee iterasies; een waar stoom direk gegenereer word uit die FVM (direkte stoomopwekking (DSO)), en 'n ander waar 'n afsonderlike vloeibare metaal/water warmteruiler gebruik word (indirekte stoomopwekking (ISO)). Eutektiese aluminium-silikon allooi (AlSi12) is gekies as die mees geskikte metaal FVM vir navorsingsdoeleindes, en eutektiese natrium – kalium allooi (NaK) as die mees geskikte warmteoordrag vloeistof. Termiese energie stoor in FVMe lei tot bewegende grens warmteoordrag berekeninge, wat ontwerps-implikasies het. Die warmteoordrag ontleding van die warmteruilers word aansienlik vereenvoudig indien kwasi-bestendige toestand warmteoordrag ontledings gebruik kan word en dit is geldig indien daar aan die Stefan toestand voldoen word. Om vereenvoudigende aannames te bevestig en om die konsep te bewys is 'n prototipe warmte stoor eenheid gebou. Gedurende toetse is daar bewys dat die vereenvoudigende aannames geldig is, dat die prototipe werk en dien as ʼn bevestiging van die konsep. Ongelukkig het onverwagte korrosie die eksperimentele werk kortgeknip, maar dit het klem op 'n belangrike aspek van metaal FVM TES geplaas. Vloeibare aluminium allooie is hoogs korrosief en dit is 'n onderwerp vir toekomstige navorsing. Om die praktiese uitvoerbaarheid van die konsep te demonstreer en om die beheerstrategie van beide voorgestelde konsepte te bevestig is 'n stoor-eenheid ontwerp vir 'n 100 MW kragstasie met 15 uur van 'n TES. Slegs AlSi12 is gebruik in die ontwerp, wat die kragsiklus beperk het tot 'n subkritiese stoomsiklus. Dit het praktiese aspekte van die konsep onderteken, en beheerkwessies rakende die DSO konsep in die kollig geplaas. In 'n tegno-ekonomiese analise van metaal FVM TES word die gevolgtrekking gemaak dat metaal FVMe gebruik kan word in samewerking met 'n vloeibare metaal warmteoordrag vloeistof om hoë temperatuur stoor moontlik te maak en dat dit ekonomies lewensvatbaar is indien die korrosie kwessies van aluminium allooi opgelos kan word. Die gebruik van gevorderde kragsiklusse, metaal FVM stoor en vloeibare metaal warmteoordrag word net geregverdig indien beduidende vermindering in GLVE van die hele kragsentrale bereik is, en dit vorm slegs 'n deel van die oplossing. ʼn Kaskade van verskeie FVMe oor 'n reeks van temperature word vereis om entropie generasie te minimeer. Twee-tenk gesmelte soutstoor kan ook gebruik word in samewerking met kaskade metaal FVM stoor om koste te verminder, maar dit moet ook verder ondersoek word.

Les centrales solaires à concentration industrielles consomment 4 m3/MWh d’eau pour le refroidissement de leur cycle thermodynamique. En environnement aride, cela est susceptible d'induire des conflits d’usages sur une ressource encore plus fondamentale que l’électricité, l'eau. Ce constat met en évidence la nécessité de concevoir des solutions alternatives de refroidissement sèches mais tout aussi efficaces. Le champ solaire d’une centrale CSP représente 50% de son coût d’investissement pour n’être utilisé que de jour pour la production de chaleur nécessaire au cycle thermodynamique. L'approche du sujet de thèse consiste à utiliser cette surface considérable comme macro-échangeur de chaleur avec son environnement via un transfert thermique couplé avec l'air ambiant (convectif) et avec l'espace extra-atmosphérique à 3K (radiatif). Après avoir démontré la pertinence des matériaux du champ solaire pour une telle application, le travail de thèse a montré expérimentalement qu'au-delà d'extraire les chaleurs fatales du cycle thermodynamique, il pouvait aussi produire du froid par transfert radiatif nocturne. Une solution alternative innovante pour le refroidissement des centrales solaires CSP offrant deux nouvelles fonctionnalités à leur champ solaire déjà existant au bénéfice de son amortissement. / Industrial concentrated solar power plants consume 4 m3/MWh of water to cool down their thermodynamic cycle. In arid area, it could induce conflicts of use on a more fundamental resource than electricity. This fact highlights the need to develop alternatives dry cooling technologies but equally effective. The solar field represents 50% of the investment cost of a CSP plant to be used only daily for the heat production needed for the thermodynamic cycle. The approach of the project is to use this huge area as macro-heat exchanger with its surrounding environment through a coupled heat transfer with the ambient air (convective) and with outer space at 3K (radiative). After validating the compatibility of solar field materials for a such application, these research works has shown experimentally that in addition to extract the waste heat of the thermodynamic cycle, it could also produce cold by night radiative cooling. An innovative alternative solution for cooling CSP plants offering two new features to their already existing solar field for the benefit of its paying off.

Convaincu de l’intérêt et du potentiel des matériaux naturels et des déchets industriels, cette thèse a contribué à la mise au point de matériaux de stockage de la chaleur (TESM) pour les CSP en Afrique de l’Ouest. Plus spécifiquement, ce travail de recherche a porté sur la valorisation de la latérite du Burkina Faso, des cendres de foyer des centrales à charbon de la société SONICHAR au Niger, des résidus en carbonate de calcium (chaux) de l’industrie de production de l’acétylène au Burkina Faso et l’huile végétale de Jatropha curcas de la société Belwet au Burkina Faso. Les résultats de cette étude ont permis de montrer que l’huile de Jatropha curcas peut être considérée comme une alternative viable aux fluides de transfert et aux TESM conventionnels pour les CSP fonctionnant à 210 °C. Les matériaux élaborés à partir des cendres de foyer et de la latérite présentent un caractère réfractaire en raison de la présence de mullite et de spinelle. L’ajout de chaux permet de réduire le point de fusion tout en préservant le caractère réfractaire et conducteur des phases obtenues. En raison de leurs stabilités, et l’absence de conflit d'utilisation, les matériaux obtenus peuvent être utilisés comme TESM dans CSP à des températures allant jusqu’à 900 °C. / Convinced of the interest and potential of natural materials and industrial waste, this thesis has contributed to the development of heat storage materials (TESM) for CSPs in West Africa. More specifically, this research focused on the valorization of laterite from Burkina Faso, the bottom ashes from the coal-fired power plants of SONICHAR in Niger, residues of calcium carbonate (lime) from the acetylene in Burkina Faso and the vegetable oil of Jatropha curcas from the company Belwet in Burkina Faso. The results of this study showed that Jatropha curcas oil can be considered as a viable alternative to conventional HTF and TESM for CSP operating at 210 °C. The materials elaborated from bottom ashes and laterites present a refractory character due to the presence of mullite and spinel. The addition of lime makes it possible to reduce the melting temperature while preserving the refractory and conductive character of the obtained phases. Due to their stabilities, and the absence of conflict of use, the obtained materials can be used as TESM in CSP at temperatures up to 900 °C.

In concentrated solar power (CSP) stations, large arrays of mirrors which are capable of changing its orientation are used to reflect the incident solar energy to a stationary receiver kept at a distance. Such mirrors are often called as heliostats. The receiver contains a heat absorbing medium like molten salt. By absorbing the thermal energy reflected from thousands of heliostats, the temperature would reach around 6000C and the heat can be used in thermal power plants to generate steam and thus run a turbine to produce electricity. One of the biggest advantages of CSP over conventional energy harvesting from Sun is that it can generate electricity during night for long hours of time from the thermal energy stored during daytime. This eliminates the usage of batteries or any other energy storing methods. The conversion efficiency is also high in CSP due to the high temperature achieved. With prior knowledge of the station coordinates, viz., the latitude and longitude, the day of the year and time, the direction or the path of sun can be fully determined. Typically, the sun's motion is tracked by the azimuth-elevation (Az-El) or the target-aligned configuration heliostats. In both these approaches, the mirror needs to be moved about two axes independently using two actuators in series with the mirror effectively mounted at a single point at the centre. This arrangement causes the mirror to deform in presence of gusty winds in a solar field which results in loss of pointing accuracy. Typically a beam error of less than 2-3 mrad is desirable in a large solar field and this value also includes other sources of loss of pointing accuracy like gravity and wind loading. In order to prevent this, a rigid support frame is required for each of the heliostats. In this work, two three degree-of-freedom parallel manipulators, viz., the 3-UPU wrist and 3-RPS, have been proposed to track the sun in central receiver systems. The main reasons for choosing a parallel manipulator as heliostat are its desirable characteristics like large load carrying capacity, high accuracy in positioning the mirror and easy to obtain the inverse kinematics and convenient for real time control. The proposed parallel manipulators support the load of the mirror, structure and wind loading at three points resulting in less deflection and thus a much larger mirror can be moved with the required tracking accuracy and without increasing the weight of the support structure. The algorithm for sun tracking is developed, extensive simulation study with respect to actuations required, variation of joint angles, spillage loss and leg intersection has been carried out. Using FEA, it is shown that for same sized mirror, wind loading of 22 m/s and maximum deflection requirement (2 mrad), the weight of the support structure is between 15% and 60% less with the parallel manipulators when compared to azimuth-elevation or the target-aligned configurations. A comprehensive study on stroke minimization of prismatic joints is carried out. It is found that a stroke of 700 mm is required for a 2 m x 2 m heliostat at Bangalore when the farthest heliostat is at a distance of 300 m from the tower. Although, there is an extra motor required to track the sun, the 3-RPS manipulator is better than the conventional methods if the mirror area per actuator criteria is taken into consideration. Prototypes of the Az-El and 3-RPS heliostats were made with a mirror size of 1 m x 1 m. A PID controller implemented using MATLAB-Simulink and a low cost, custom made motor driver circuit is used to control the motion of the 3-RPS heliostat. The algorithm developed is tested on the prototype by tracking a point marked on the wall of the lab space and is found to have a tracking error of only 7.1 mrad. Finally, the actual sun tracking is carried out on the roof of a building reflecting the sun-light to a wall situated 6.72 m above and a distance of 15.87 m from the heliostats. The images are captured at various instances of time from 11:30 a.m. to 3:30 p.m. on October 15th and November 10th, 2016, tracking errors are quantified and it is demonstrated that the proposed 3-RPS parallel manipulator can indeed work as a heliostat in concentrated solar power plants.

Par rapport aux ressources énergétiques fossiles combustibles, l’énergie solaire présente des caractéristiques inhérentes à la nature même de la ressource. Ce constat met en évidence la nécessité de système de stockage d’énergie. Ce travail de thèse consiste à étudier un stockage thermique pour une centrale solaire à concentration, ainsi que ses deux composants essentiels : le fluide de transfert et les matériaux de garnissage solides. La compréhension du système de stockage thermocline sur lit de roche est réalisée grâce à une approche expérimentale et numérique. Une alternative innovante sur le choix du fluide de transfert consiste à utiliser des huiles végétales. Concernant le garnissage, un matériau à géométrie contrôlée est développé à partir d’un coproduit issu de la sidérurgie. L’originalité de cette association pour le stockage thermique permet d’allier performance, disponibilité des matériaux en quantité industrielle tout en réduisant l’impact environnemental et financier. / Compare to fossil fuel energy resources, solar energy presents the inherent characteristic given by the very nature of the resource (intermittent availability). This observation highlights the need for thermal energy storage system. This doctoral thesis studies thermal energy storage for concentrating solar power plant, as well as its two essential components: the heat transfer fluid and the thermal energy storage materials. The analysis of the thermocline storage system with filler materials is achieved through experimental and numerical approaches. An innovative alternative for the heat transfer fluid consists to use vegetable oils, which offers comparable thermal properties and operating behavior to conventional thermal fluid. Regarding thermal energy storage materials, many natural and recycled materials can be used. A storage material with controlled geometry is developed from steel industry co-product. The originality of this combination for thermal energy storage combines performance, materials availability at industrial scale while reducing environmental and financial impact.

This thesis describes a concentrating solar power using a Stirling engine. The problems encountered during construction and operation. I focus mainly on problems derating dusting and icing. The second part of this work is the experimental design of the stand with long-term measurement of dusting depending on the reflectivity of mirrors and their degradation under various conditions. First measurement is stated and estimation of long-term results.

Hybrid solar-Brayton systems utilize both solar thermal energy and supplementary renewable fuels to provide controllable and dispatchable power output, which renders them a promising way to meet the growing energy demand and reduce the carbon footprints. However, existing testing facilities for key components in such hybrid systems often fail to accomplish the testing requirements, hence impeding the improvement of the renewable energy share and the overall efficiency. A novel testing facility is urgently needed in order to thoroughly stimulate and analyze the component characteristics. This research work focuses on the development of a gas turbine simulator as an innovative testing facility for hot, pressurized components in hybrid solar-Brayton systems. The dual-flow choked nozzle based flow control has been proposed, explained, and analyzed in comparison to the single-flow layout. The basic idea of gas turbine simulator has been experimentally implemented and validated on a prototype, verifying its functionality. By incorporating a PLC-based control system, an automated gas turbine simulator has been designed and modified based on the prototype. Its performance with regard to stabilizing boundaries and tracking trajectories has been evaluated by experiments. Based on the experimental results, the gas turbine simulator prototype has proven its ability to establish controllable boundary conditions and migrate operating points for the impinging receiver. Through manual adjustments, excellent quasi-steady state performance has been obtained, with the precision for pressure control reaching ±0.005 bar at ambient temperature and ±0.015 bar at high temperature of 797.1-931.5 °C. The manual operation time has been identified at 23.1 s for establishing the receiver boundaries, and at 70 s for changing operating points. With the help of the proposed control strategy, the automated gas turbine simulator has eliminated the need for manual adjustments, and demonstrated the ability to maintain the safe and convergent operation for the receiver. The performance in boundary condition stabilization has been satisfactory, with enhanced steady-state accuracy comparing to the prototype by virtue of the PID controller. The transient-state fluctuations in pressure control have been effectively restrained within an acceptable region with deviations of ±0.018 bar to ±0.076 bar from the desired 2.400 bar operating pressure. The capability of tracking linear and nonlinear trajectories has also been testified, with the precision level between ±0.023 bar and ±0.037 bar. Finally, in view of the good stability, high precision, and rapid response manifested in the experimental studies, the gas turbine simulator has validated its ability to imitate the steady and transient characteristics of gas turbines on the boundaries of the test section. It also grants the possibilities to conduct control variable studies and wide-range transition studies. The gas turbine simulator is a suitable testing facility for the key components in hybrid solar-Brayton systems. / Hybrid solenergi-Brayton-system använder både solvärmeenergi och kompletterande förnybara bränslen för att ge kontrollerbar och sändbar effekt, vilket gör dem till ett lovande sätt att möta den växande energiefterfrågan och minska koldioxidavtrycken. Men befintliga testanläggningar för nyckelkomponenter i sådana hybridsystem misslyckas ofta med att uppfylla testkraven, vilket hindrar förbättringen av andelen förnybar energi och den totala effektiviteten. En ny testanläggning behövs omgående för att grundligt stimulera och analysera komponentens egenskaper. Detta forskningsarbete fokuserar på utvecklingen av en gasturbinsimulator som en innovativ testanläggning för varma, trycksatta komponenter i hybridsolar-Brayton-system. Den dubbelströms strypta munstycksbaserade flödeskontrollen har föreslagits, förklarats och analyserats i jämförelse med enkelflödeslayouten. Den grundläggande idén med gasturbinsimulator har experimentellt implementerats och validerats på en prototyp, vilket verifierar dess funktionalitet. Genom att införliva ett PLC-baserat styrsystem har en automatiserad gasturbinsimulator designats och modifierats utifrån prototypen. Dess prestanda med avseende på stabilisering av gränser och spårning av banor har utvärderats genom experiment. Baserat på de experimentella resultaten har prototypen av gasturbinsimulatorn bevisat sin förmåga att upprätta kontrollerbara gränsförhållanden och migrera arbetspunkter för den träffande mottagaren. Genom manuella justeringar har man erhållit utmärkt prestanda i nästan konstant tillstånd, med precisionen för tryckkontroll som når ±0,005 bar vid omgivningstemperatur och ±0,015 bar vid hög temperatur på 797,1-931,5 °C. Den manuella drifttiden har identifierats till 23,1 s för att fastställa mottagargränserna och till 70 s för att byta arbetspunkter. Med hjälp av den föreslagna styrstrategin har den automatiserade gasturbinsimulatorn eliminerat behovet av manuella justeringar och visat förmågan att upprätthålla en säker och konvergent drift för mottagaren. Prestandan vid gränstillståndsstabilisering har varit tillfredsställande, med förbättrad steady-state noggrannhet jämfört med prototypen tack vare PID-regulatorn. De transienta tillståndsfluktuationerna i tryckregleringen har effektivt begränsats inom ett acceptabelt område med avvikelser på ±0,018 bar till ±0,076 bar från det önskade 2,400 bar arbetstrycket. Förmågan att spåra linjära och olinjära banor har också vittnats, med precisionsnivån mellan ±0,023 bar och ±0,037 bar. Slutligen, med tanke på den goda stabiliteten, höga precisionen och snabba responsen som manifesteras i de experimentella studierna, har gasturbinsimulatorn validerat sin förmåga att imitera de stabila och transienta egenskaperna hos gasturbiner på gränserna för testsektionen. Det ger också möjlighet att genomföra kontrollvariabelstudier och omfattande övergångsstudier. Gasturbinsimulatorn är en lämplig testanläggning för nyckelkomponenterna i hybridsolar-Brayton-system.

L'énergie solaire est connue pour sa nature intermittente par rapport aux ressources d’énergie fossile. Cette observation souligne la nécessité d'utilisation d’un système de stockage d'énergie thermique. Le système de stockage thermocline est considéré comme un système de stockage rentable. La présente thèse vise à étudier le potentiel des roches basaltiques et siliceuses comme des candidates matériaux de stockage pour les centrales solaires concentrées. Les études expérimentales des propriétés thermo-physiques et thermomécaniques de ces roches à des températures allant jusqu'à 1000°C montrent que ces roches offrent de bonnes propriétés thermiques par rapport aux matériaux classiques de stockage. L'analyse du système de stockage thermocline sur un lit de roches à air direct est réalisée par une approche numérique. En outre, cette recherche vise également à évaluer l’impact environnementale de ce type de système de stockage en effectuant une analyse comparative de son cycle de vie. Enfin, une étude complémentaire réalisée dans le but de produire une carte d'indice de pertinence a permis d’identifier les zones les plus appropriées pour la construction des centrales solaires en Egypte. L'originalité de cette approche alternative pour le stockage d'énergie thermique est qu’elle combine la performance et la disponibilité des matériaux de stockage tout en réduisant leurs impacts environnementaux et financiers. / Compare to fossil fuel energy resources, solar energy is known for its intermittent nature. This observation highlights the need for the use of a thermal energy storage system. The thermocline storage system is considered as a cost-effective storage system. This thesis aims to study the potential of basalt and silex rocks as candidate storage materials for concentrated solar power plants. Experimental studies of the thermo-physical and thermo-mechanical properties of these rocks at temperatures up to 1000°C show that these rocks offer good thermal properties compared with conventional storage materials. The analysis of the thermocline storage system of air rock-packed bed is carried out using a numerical approach. This research also aims to assess the environmental impact of this type of storage system by conducting a comparative analysis of its life cycle. Finally, a complementary study carried out with the aim of producing a relevance index map made it possible to identify the most suitable areas for the construction of solar power plants in Egypt. The originality of this alternative approach for thermal energy storage is that it combines the performance and availability of storage materials while reducing their environmental and financial impacts.

Concentrating Solar Power (CSP) is one of the most promising renewable energybased electricity generation technologies to deal with the increasing demand of power consumption and environmental sustainability. With the aim of achieving the 2020 SunShot cost target for CSP of 60 USD/MWh, the United States Department of Energy presented, in May 2018, the Gen3 CSP initiative. In particular, the CSP Gen3 Liquid-Phase Pathway proposes to design a CSP system adopting liquid sodium as Heat Transfer Fluid (HTF) in the receiver, advanced high-temperature molten chloride salt as storage fluid and supercritical CO2 (sCO2) Brayton cycle as power cycle. Within this framework, the aim of this master thesis was to design the sodium-chloride salt Heat Exchanger (HX) by developing both a heat exchanger model and a sodiumsalt-sCO2 system model. To pursue these purposes, a completely new Modelica-based HX model was developed and added to the SolarTherm library. Furthermore, as an extension of earlier models, the sodium-salt-sCO2 CSP system (NaSaltsCO2System) was implemented in SolarTherm, by incorporating the HX model and linking it with other new and existing component models. As for the HX, a general model was developed for shell and tube heat exchangers, based on the TEMA guidelines, with the possibility of being customized in terms of media adopted, constraints, boundary conditions, and correlations. The model performs an optimization in order to select the internal geometry configuration that optimizes a user-defined objective-function. By employing the implemented HX model in the NaSaltsCO2System, the sodium-salt heat exchanger was designed aiming at minimizing the Levelized Cost of Electricity (LCOE), providing a complete geometry description, and an estimation of the performances and costs. The resulting NaSaltsCO2System model was found to be robust and able to perform annual simulations that allowed to estimate the energy performances of the CSP plant, as well as the LCOE. Considering the sodium-salt-sCO2 CSP system characterized by a receiver capacity of 543 MWth, 12 hours of Thermal Energy Storage (TES), and a 100 MWe power block, the LCOE resulted equal to 72.66 USD/MWh. The sodium-salt HX design that minimizes the LCOE resulted in a single-shell/single tube pass configuration, with vertical alignment, characterized by an overall height of 15 m, and a shell diameter of 1.8 m. It represents the 3.2% of the total capital cost of the plant. An interesting system-level optimization was then carried out on the combined receiver-heat exchanger block. It regarded the variation of the Log Mean Temperature Difference (LMTD) of the HX and highlighted the possibility to drop the LCOE down to 68.54 USD/MWh. The techno-economic investigations and the sensitivity analysis showed the flexibility and robustness of the HX model, as well as the importance of the NaSaltsCO2System. The latter lays the groundwork to explore potential improvements of this new generation of CSP systems, which can play a fundamental role in the future global energy mix. / Termisk solkraft (CSP) är en av de mest lovande elproduktionsteknologierna baserade på förnybar energi. Den kan bidra till hanteringen av den ökande efterfrågan på energi och miljömässig hållbarhet. I syfte att uppnå 2020 SunShot-kostnadsmålet för CSP på 60 USD/MWh presenterade USA:s energidepartement Gen3 CSPinitiativet. I synnerhet föreslår CSP Gen Liquid-Phase Pathway att utforma ett CSPsystem som använder flytande natrium som värmeöverföringsvätska i mottagaren, smält kloridsalt med hög temperatur som lagringsvätska, samt superkritisk CO2 (sCO2) Brayton-cykel som kraftcykel. Syftet för detta examensarbete var att utforma natriumkloridsaltets primära värmeväxlare genom att utveckla både en värmeväxlarmodell (HX) modell och en natriumsalt-sCO2-systemmodell. För att fullfölja dessa syften utvecklades HX-modellen först, sedan implementerades natriumsalt-sCO2 CSP-systemet NaSaltsCO2System. Båda verktygen utvecklades med hjälp av Modelica som programmeringsspråk. De finns nu tillgängliga i det öppna SolarTherm-biblioteket. När det gäller HX utvecklades en allmän modell för skal- och rörvärmeväxlare med möjligheten att anpassas när det gäller antagna medium, begränsningar, gränsvillkor och korrelationer. Dessutom utförde modellen en optimering för att välja den interna geometri-konfigurationen som optimerar en användardefinierad objektiv-funktion. Genom att använda den implementerade HX-modellen i NaSaltsCO2System designades natriumsalt-värmeväxlaren, vilket gav en fullständig konfiguration-beskrivning och en uppskattning av prestanda och kostnader. Den utvecklade NaSaltsCO2System-modellen visade sig vara robust och kapabel till att utföra simuleringar på årsbasis. Detta gjorde det möjligt att uppskatta CSP-anläggningens energiprestanda samt LCOE. Det utvecklade natriumsalt-sCO2 CSP-systemet som känneteckna des av en mottagarkapacitet på 543 MWth, 12 timmars TES och ett 100 MWe power block, resulterade i en LCOE på 72.66 USD/MWh. Natrium-salt HX-konstruktionen som minimerade LCOE resulterade i en enskalig/enkel rörpassningskonfiguration, med vertikal inriktning, kännetecknad av en total höjd av 15 m och en skaldiameter på 1.8 m. Det motsvarade 3.2% av anläggningens totala kapitalkostnad. Den mest intressanta systemoptimeringen genomfördes på det kombinerade blocket bestående av mottagare och värmeväxlare. Den behandlade variationen av HX:s LMTD och framhöll möjligheten att sänka LCOE till 68.54 USD/MWh. De teknisk-ekonomiska undersökningarna och känslighetsanalysen visade flexibiliteten och robustheten i HX-modellen, liksom vikten av NaSaltsCO2Systemet. Den senare lägger grunden för att utforska potentiella förbättringar av denna nya generation av CSP-system, som kan spela en grundläggande roll i den framtida globala energimixen.